Search Documents

By P. C. Thakur

Frictional ignitions (also called face ignitions) is defined as the rapid oxidation of a mixture of methane and air with a visible flame that could last from a few seconds to several minutes. These ignitions have a potential to turn into a mine explosion and eventually a large-scale mine fire. Over the last 22 years, U.S. coalmines have had 1566 frictional ignitions. There were no fatalities but serious injuries have occurred. Every effort, therefore, should be made to prevent frictional ignitions. The preventative measures fall under four categories: (a) degasification of coal seams prior to mining, (b) adequate ventilation, (c) wet cutting or water-jet assisted cutting and (d) machine design to minimize ignitions. The paper discusses each of these techniques in detail.

Jan 1, 2006

Crushing and grinding activity in 1989 followed the rapid pace of the mineral industry. Use of existing installations, demand for expanded capacity, and implementation of entirely new operations contributed to a high level of activity. At the 1989 SME-AIME Annual Meeting in Las Vegas, NV, the crushing and grinding session focused on wear materials in crushers and mills. Another session joined the process control group in its simulation-modeling and control of crushing and grinding circuits. Both sessions addressed the optimization in operating effectiveness. Specific subjects covered grinding media wear of forged and cast grinding balls and rubber lined mill liner wear. Also, the Semi Autogenous Grinding (SAG) Mill Conference in Vancouver in September 1989 provided a valuable update on the progress of SAG operations in recent years. Operationally, gold grinding and roasting circuits were implemented in 1989. Freeport McMoRan Gold started up two operations in Nevada. Two other circuits, both using SAG mills, are scheduled to start in 1990. These will be in Nevada and British Columbia. Elsewhere in gold, additional capacity continues to be brought onstream, both domestically and worldwide. In copper, expansions continue to call on additional crushing and grinding units. The unrest at Bougainville in Papua New Guinea has fueled a continued, strong demand for comminution in the copper sector. Specific equipment installed or started in 1989 included the ac variable frequency drive SAG mills in Australia, Alaska, and Papua New Guinea. Also, the gearless drive SAG mill in Chile provides tremendous flexibility in terms of mill speed. The trend toward moveable in-pit crushers continues -even at established operations.

Jan 1, 1990

By C. I. Wilmot

The paper presents an update of the Paradise Peak mill after the first year of operation. Process revisions, equipment modifications and additions, and personnel requirements are discussed with a comparison to original design. All areas of milling are discussed including crushing, grinding, leach/countercurrent decantation (CCD), precipitation, refinery, and heap leach.

Jan 1, 1987

New developments in the pipe conveyor and belt are advanced to address the growth in the capacity, length and complexity of pipe conveyor systems. Improved belt construction can offer better stability during horizontal curves and resistance to twist. Low rolling resistance rubber compound can significantly lower the power consumption and belt tension, producing capital and operation cost savings. Dynamic analysis, when used to analyze the conveyor?s starting and stopping behavior, can improve the design and reliability of long overland pipe conveyor systems. For these three aspects, technical backgrounds and field installations as examples are discussed in this paper.

Jan 1, 2012

By T. Bajpayee, L. Prosser, A. Iannacchione

Reducing the number of roof fall injuries is a goal of the NIOSH mine safety research program. Central to this effort is the development of assessment techniques that will help to identify the nature of the risks associated with working under potentially hazardous roof conditions. This paper discusses a method to determine the roof fall risk using a qualitative risk analysis technique. The ability to determine roof fall risk has been a long-standing goal of safety professionals and can provide the kind of information, needed by on-site personnel responsible for worker safety, to mitigate roof fall injuries.

Jan 1, 2007

By John O. Marsden

Process selection is the systematic development of the optun.m metal extraction route for a particular feed matenal and has two main objectives: (1) to optimize project economics, principally a function of gold recovery, throughput rate and processing costs, and to develop a process that satisfies all of the proct requirements including, for example, political and environmental considerations.

Jan 1, 1992

By Van Zyl Brink

A longwall-based coal mine in Australia, referred to in this paper as AusMine Colliery, experienced windblasts resulting from goaf falls. Windblasts were the cause of serious injuries and threatened the continued operation of the mine. A microseismic early warning system was installed and a significant success rate in providing early warning of large roof instability resulting in high velocity windblasts, has been achieved. Early warning of goafing is accepted as an operational tool on the mine. Severe demands are placed on the operator in terms of 'real time' interpretation. The development of an expert system allowed for a probabilistic approach to achieve automatic alarms. This paper will quantify the success, failure and false alarm rates achieved by manual operation and automatic expert system-based decisions making, respectively.

Jan 1, 2002

By Hans W. Brodbeck

The Advisory Conference on Tunnelling of the OECD, held in Washington, D.C. in June 1970, has established the following definition: "Tunnelling refers to the construction by any method of a covered cavity of predesigned geometry whose final location and use are under the surface, whose cross-sectional area is greater than 2 square metres". (1) The definition makes clear that the term includes all types of underground construction, be it in hard rock, soft ground, under mixed conditions, underwater, etc. Small-sized tunnels in rock therefore constitute but one part of the tunnelling scene. With an ever-growing urbanisation taking place in industrialized as well as developing countries, the demand for small-sized tunnels is, however, rapidly increasing and requires a far-reaching mechanization of excavation and support functions. This trend is accentuated by the fact that small-sized tunnels are far more labor-intensive than large ones, and, with wages raising at a much faster rate than costs for plant and equipment, this will accelerate the introduction of new tunnelling systems. SMALL-SIZED ROCK TUNNELS The main field of application for a tunnelling system for small sized hardrock bores is thus defined. It is in fact the numerous relatively short tunnels required under cities and other populated

Jan 1, 1974

By Norman Miskelly

Substantial progress has been made over the last ten years in the development of uniform national and international standards covering the definition, estimation and public reporting of mineral resources and mineral reserves. Agreement between the major participating countries has been reached, which include the requirement that a Competent Person prepares and approves publication of mineral resources and reserves. Most national regulatory organizations have accepted the new standards and have included them in the rules that must be followed by mining companies operating under their jurisdiction. These developments are the result of a concerted effort on the part of professional societies, national regulatory agencies, international organizations, and many dedicated individuals. The historical development of these standards is summarized in this paper. Accepted definitions of mineral resources and mineral reserves are discussed, as well as the definition and role of the Competent Person. Additional effort is needed before the international standards are fully understood, accepted and followed by mining companies, regulatory agencies, the investment community and the general public. Steps being taken toward development of a Mineral Reserves International Reporting Code Template (International Template) that will be available for all countries to use in deriving their specific country reporting codes, are outlined

Jan 1, 2003

By S. Lähteenmäki, P. Koivistoinen, J. Levanaho

Semi Autogenous Grinding (SAG) circuit is the most common grinding circuit to day. In Europe and South Africa fully autogenous (AG) circuits are also popular. SAG circuit has a lower capital cost and simple operation. SAG circuit requires the use of grinding balls, which increases operating costs and decreases availability. An AG circuit may produce a higher Net Present Value to the investment. The AG circuit is more complex to design and operate. However, operating experience from AG circuits illustrates that an AG circuit can be as trouble free as a SAG circuit with the benefit of lower operating cost.

Jan 1, 2001

By Luke Erickson

San Francisco Public Utilities Commission is planning to replace 5 miles of pipeline under San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance (EPB) TBM and will be the first TBM-driven tunnel under the Bay. The alignment passes under environmentally sensitive habitats, through interbedded layers of sands and clays, and through a buried bedrock ridge. This paper discusses the geotechnical characterization and anticipated tunneling conditions and presents the analysis of various construction methods that resulted in the selection of an EPB TBM. Considerations related to tunneling with an EPB TBM are described in detail, including ground conditioners, TBM cutterhead wear, muck control, and squeezing ground.

Jan 1, 2008

By Mark C. Holton

The mining industry has recently been. - experiencing a difficult period. Escalating costs, lower grades and deeper level mining, are a few of .the reasons' why interactive graphics or CADD (computer aided design and draughting) systems are increasingly being used. CADD systems which support powerful and flexible mining applications have great potential for making all forms of mining more efficient and effective. There are many application programs which address almost every aspect of mining. Most of these programs originated to satisfy a particular need. Graphics and other features were added until they, reached a point where they were commercially viable as a mining package. Because of their evolution these packages, lack many CADD-type features. Today there are powerful personal computers (PC's) and engineering workstations running the best CADD systems available. These systems, support hundreds of applications in almost every discipline. Mining was until recently not well supported by interactive graphics vendors because of the highly variable nature of mining and the lack of common standards. Users of CADD systems have experienced the benefits of CADD and come to expect similar features from graphic mining packages. Several developers of mining packagers have either attempted to include some CADD features or make their packages compatible with one or other CADD system. Mining can benefit greatly From a combination of interactive graphics (or CADD) and the right mining application software.

Jan 1, 1989

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

10.1 I~RODUC1'ION In order to understand the effects of surface subsidence due to underground mining on the ground water hydrology, a brief introduction to the rate, direction, and general pattern of ground water movement in aquifers is necessary. Ground water movement in an aquifer is controlled by aquifer lithology, structure, permeability, water levels, topographic set¬ting, and pumping patterns (Sgambat et al., 1980). Fig. 10.1 shows an idealized flow pattern of ground water in a hilly terrain (Coe and Stowe, 1984). The hill is made up of a series of interbedded permeable aquifers (mostly sandstone) and confining units (mostly shale). Since sandstone is porous and permeable, ground water moves through it downward and laterally until it reaches the interbeddings of the confining unit immediately below. The ground water then moves laterally along the interbeddings, be¬cause the confining unit is less permeable, and comes out as springs on the surface at the intersection of the aquifer and the confining unit. If there is a ground water table in each aquifer, it is a perched water table (e.g., right side of Fig 10.1). On the other hand, if the ground water recharge is larger than can be drained out, the interbedded permeable aquifers and confining units will be filled with water and a ground water table will exist only at the uppermost permeable aquifer. This is the semi-perched water table (e.g., left side of Fig. 10.1). There are three ground water flow systems: shallow, interme¬diate, and deep. Shallow flow systems occur near the land surface and the surface drainage system. The flow depth ranges from a few to several hundreds of feet with a resident time of a few weeks to a few years after entry, depending on the permeability of the rock strata. In a shallow flow system, the drainage coincides with sur¬face run-off water divides. Intermediate flow systems occur in minor hills some distance away from surface drainage. The travel distance ranges from several hundreds to several thousands of feet, the travel time from several months to tens of years. These systems are less dependent on seasonal recharge or discharge. In deep flow systems, the ground water travels from thousands of feet to miles, and transfers between surface basins. The travel time ranges from several tens to several hundreds of years. The systems generally receive recharge over a large area on major mountains and dis¬charge into major stream systems. 10.2 CASE STUDIES There are two ways of monitoring water wells for studying the effects of dewatering due to underground mining, i.e., water level and piezometric level. The water level is the water elevation in a water well that has penetrated two or more aquifers. Thus it indi¬cates the combined flow of all the aquifers that the water well intersects during the time of measurement. The piezometric level is the level to which water rises in a piezometer cased to a specific aquifer, and coincides with the pressure level of water in that aquifer. Therefore piezometric level reflects the water condition in that particular aquifer to which it is confined, while the water level represents the total yield of a water well without regard to the source of water. For instance, if a water well intersects two aqui¬fers, and if the lower aquifer is affected by undermining and goes dry while the upper aquifer does not, the water level in the well will drop, but may never go dry. Under this condition, the data obtained by monitoring the water level do not indicate the true behavior of the individual aquifers, especially if they are located at widely separated heights. 10.2.1 WATER LEVEL EFFECTS The effects of underground mining on ground water flow have been the subject of many investigations (Booth, 1984; Coe and Stowe, 1984; Owili-Eger, 1983; Rauch et al., 1984). However, the problems are very complicated, as have been exemplified by the conflicting conclusions reached by various investigators in var¬ious case studies. The most dramatic examples were described by Coe and Stowe (1984). In the first case (Fig. 10.2), the coal seam was 5 ft thick with cover from 400 to 800 ft deep. The majority of water supplies came from a sandstone aquifer in most ridge tops. When the face of the Panel No. 3 passed under it, dug well WW-1, which was approximately 670 ft above the coal, went dry, while the water level in Borehole B- 1, which was located at the center of Panel No. 4 with the bottom reaching the coal seam, also dropped about 160 ft. In Panel No. 5, the developed spring DS-2, which originated from the surface of the sandstone/shale contact and was approximately 750 ft above the coal seam, stopped when the face passed under it. The water level in the dug well W-2, which was dug into the shale about 700 ft above the coal seam dropped about 22 ft, but the well did not go dry. Therefore, nearly every spring or well located above or near the active panels was affected by longwall mining. In the second mine (Fig. 10.3), the seam was 5 ft thick with cover from 200 to 400 ft thick. Dug well DW-2, the bottom of which was 35 ft deep and approximately 330 ft above the coal seam in a perched sandstone aquifer, went dry right after the longwall passed under it. Drilled well W-3, in the sandstone aquifer, about 220 ft above the coal seam, experienced a 75-ft drop in water level when the face was under it, but showed some re¬covery after the face had passed under it. Ponds P- I and P-2 were developed in shale bedrock and were spring fed. They were not affected by longwall mining. Pond P-3 was developed in the sand¬stone aquifer, and its water table showed some decline when the face passed under it. Spring ST-1, which originated from Pond P-1 and was fed from several tributary valleys, was affected by longwall mining, probably because it passed across the panel edges where tension cracks drained off the water. Although the overbur¬den in case 2 was about half of that in case 1, the majority of water resources were not affected by longwall mining. Coe and Stowe (1984) attributed this discrepancy to: (1) a higher percentage of clays, shales, and claystones, resulting in a lesser degree of inter¬connected fracturing, and (2) a less rugged topography resulting in a less localized ground water flow system. Therefore, in order to assess the effects of underground mining, the premining ground water flow patterns, topographical, lithological, and meterological conditions must be known. Booth (1984) also monitored the ground water effects of a longwall mine (Fig. 10.4) in a seam 5 ft thick and 300 to 800 ft deep. There were three major aquifers: Morgantown sandstone approximately 30 ft thick and 630 ft above the coal; Saltsburg sandstone of up to 50 ft in thickness and 520 ft above the coal; and

Jan 1, 1992

By Harold D. Taylor

Lognormal grade distributions are definitely the rule rather than the, exception in many types of deposits, including precious metals, uranium, and many others. The "normal theory" geostatistical techniques do not work well in these situations because the occasional high grade values, perhaps several orders of magnitude larger than the median, can overwhelm the rest of the data, resulting in variograms and Kriged estimates which are unrealistic or even ridiculous. Robust techniques for variogram modeling have been proposed, and truncation of high sample values can produce more reasonable Kriged estimates, but the technique of working with log transformed data appears to be the best method of handling lognormal data. This paper will discuss primarily the two parameter lognormal case, with some discussion of the three parameter lognormal, but no discussion of other methods of transforming data, such as disjunctive Kriging.

Jan 1, 1982

By F. J. Klingler, R. Hausmann, K. M. Swaffar, J. C. Neyer

This paper presents the results of a study of case histories of projects on which sinking caissons were used to construct shafts for tunnel construction and other underground works. Design methodologies are reviewed with respect to the impact of soil and groundwater conditions on the performance and constructability of sinking caissons. Factors which have led to success or failure are reviewed and evaluated, and recommendations for future investigation, design and construction activities are presented. Cost data for five recent projects are reviewed and compared to the cost of shaft installation by other means.

Jan 1, 1997

By Jamal Rostami, Alireza Salimi, Christian Moormann

"Rock mass classification systems are often applied in many empirical design practices in rock engineering, some contrasting with the original intent and applications of these classification systems, for example, estimation of TBM performance in various ground conditions. While accurate estimation of machine performance is significantly impacted by rock mass properties, parameters used in many of the existing classifications are more related to ground support design and not rock mass boreablity. The results of many investigations on this issue have shown a weak correlation between TBM rate of penetration and rock mass classification. This limitation can be overcome by fine tuning the rock mass classification input parameters to represent influence of rock mass properties on TBM performance as has been the objective of RME or QTBM. This paper will offer an overview of the impact of rock mass on TBM performance and introduces an empirical equation for predicting performance of rock TBMs based on rock mass classification. The results of the preliminary analysis of a new model has revealed that the use of the proposed system can offer a reasonable accuracy for estimation of TBM performance in various rock masses. 1. INTRODUCTION Hard rock tunnel boring has become more or less the standard method of tunneling for tunnels of various sizes with lengths over 1.5–2 km. Estimating the performance of TBM is a vital phase in tunnel design, and for the choice of the most appropriate excavation machine. During the past three decades, numerous TBM performance prediction models for evaluation of TBM rate of penetration and advance been proposed. In brief, all the TBM performance prediction models can be divided into two distinguished approaches, namely theoretical and empirical ones (Rostami et al., 1996). The most common and recent works on this topic are summarized in Table 1. Currently, two models including Colorado School of Mines or CSM (Rostami and Ozdemir, 1993; Rostami, 1997) and Norwegian University of Science and Technology or NTNU (Blindheim, 1979; Bruland, 1998) models are the most recognized TBM performance prediction and prognosis models in use around the world."

Jan 1, 2016

By M. E. Smith

Waste rock dumps, tailings impoundments and spent leach heaps are common features at mine sites. Many of these waste disposal facilities contain sulfide-rich minerals, which generate acid mine drainage (AMD) when they oxidize. Control of AMD can be achieved by removing one or more of the three essential components in the acid-generating process (sulfides, air, or water). One AMD prevention measure is to cap the waste with an engineered cover system to minimize the infiltration of water and diffusion of air into the system. Possible cover designs include: ? Earthen ?store-and-release? covers (also known as evapotranspiration (ET) or water balance covers), including capillary barriers. These covers require climate conditions where there is both modest to little rainfall and significantly greater evapotranspiration than precipitation, both annually and seasonally. ? Low-permeability compacted clay liners (CCLs) employing fine-grained soils typically compacted at wet of optimum water content. ? Geosynthetic composite covers, comprised of a geomembrane liner placed over and in direct contact with either a CCL or a geosynthetic clay liner (GCL). These systems have been commonly used for base liners for leach pads as well as covers and base liners at municipal solid waste (MSW) landfills in the US for more than 20 years. Comparisons of these different cover systems, both in terms of performance and cost, are presented later in this paper. First, however, a review of the typical mine closure approaches, and the possible rationale behind them, is warranted.

Feb 27, 2013

By G. H. Kuhnhausen

The Bear Creek Uranium Mill was designed in 1975 to process 909 tonnes per day (1000 STPD) of low-grade uranium ore from the Powder River Basin in Wyoming. The mill was expanded to 1818 tonnes per day (2000 STPD) in 1979. The Bear Creek Uranium Project is owned by the Bear Creek Uranium Company, a partnership of Rocky Mountain Energy Company and Mono Power Company. The original mill design contemplated processing ores from Bear Creek Uranium Company properties exclusively. The expanded capacity has been utilized for tolling ores from Kerr McGee Nuclear Corp. and other mining companies in the region. This paper describes the process of designing the original mill, the lessons learned from operation, and the design of the process modifications required for expansion. The project background, design philosophy, design basis, design criteria, actual flowsheet, special design considerations, and a comparison of assumed operating conditions and actual operating results will be presented. Bear Creek Uranium Company wishes to thank and acknowledge the help granted by the many operating companies who provided invaluable information, insight, and critique of the Bear Creek design through all the various stages and were instrumental in the successful completion and start-up of the mill. Without their contributions, the design philosophy used at Bear Creek would not have been possible and the results obtained would surely have been less satisfactory.

Jan 1, 1979

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The integrated grouting method, as developed in the USSR, can be applied to multi-purpose operations that in¬clude the construction of shafts, drifts, and tunnels. In the USSR it has been used extensively for primary and final grouting of underground excavations in mining engineering and civil engineering projects. It has been applied in projects where the primary objective was waste contain¬ment. It has also been used to control subsidence beneath buildings located over mined out openings and to eliminate the flow of ground water beneath and around dams. This chapter considers several industrial applications in the form of case histories. The word integrated means that grouting activities were integrated with other activities. 9.1 CASE HISTORIES OF GROUTING FRACTURED ROCK WHEN SINKING VERTICAL SHAFTS The integrated grouting method has been applied most widely in the sinking of vertical shafts in fractured, satu¬rated rock. As explained previously herein, grouting oper¬ations preferably are carried out from the ground surface where they are integrated into the schedule of the setting up of the shaft excavation and construction equipment. Such integration reduces significantly the length of time required for preparation of shaft construction and the time required to sink the shaft. The increased efficiency is achieved by the elimination of cementing operations from the working face upon the penetration of each aquifer. Concomitantly, labor and energy consumption during shaft sinking are minimized because the more complicated and labor-intensive work is carried out at the surface section. Table 9.1 presents the essential parameters for the pri¬mary grouting of saturated fractured rock carried out by the integrated method when sinking vertical shafts. 9.1.1 NAGOL'CHANSK MINE NO. 1-2, VENTILATION SHAFT NO. 1 The integrated method of grouting saturated fractured rock through holes drilled from the surface was employed for the first time during the sinking of vertical shaft No. 1 at the Nagol'chansk mine No. 1-2 in the Don Basin. The shaft had an inside diameter of 6 m. The grouting operations commenced by using cement grout with a density of 1.7 to 1.8 g/cm3. Clay-based grout with cement and other addi¬tives was used only for grouting the aquifers where cement grout proved to be ineffective. By the time of the grouting of ventilation shaft No. 1, hydrodynamic analytical methods were well in hand and a preliminary method for designing isolation curtains had been developed. A method for designing and drilling ori¬ented directional drillholes whose natural curvature re¬flected the characteristics of the fracturing had been devel¬oped. The majority of the necessary equipment had been developed. Clay-based grouts were considered ready for the first industrial application. The hydrogeologic environment at the Nagol'chansk mine No. 1-2 contained many prolific aquifers. According to monitored drillhole data, the total expected inflow into ventilation shaft No. 1 without grouting was 425 m3/hr. This large ground water inflow rate was supported by in¬formation obtained during the sinking of the main shaft and from the auxiliary shaft of the "Nagol'chansk" mine No. 1-2. The construction contractor at the site began sinking ventilation shaft No. 1 to a depth of 217 m by cement grouting from the working face of the shaft. As a result of the cement grouting operations, the inflow of water was reduced from 105.4 to 40 m3/hr over this 217 m interval. However the residual inflow rate caused the shaft to become functional at the depth of 217 m. At this point all grouting operations were transferred to SPETSTAMPONAZHGEOLOGIA (STG) in an effort to improve the operation. In order to carry out preliminary grouting from the sur¬face, seven drillholes were installed and designed for re¬ceiving grout. Drilling was implemented by the ZIF-1200A rig to the design depth of the shaft. The geometry of the principal fracture system that would be encountered by the shaft was estimated while breaking ground using informa¬tion from other shafts. The drillholes were arranged so that they cut through the aquifers uniformly around the shaft. Some preference was given to intercepting the aquifers that were located along the rock dip above the shaft bottom because it was established that the ground water in the aqui¬fers flowed downward along the dip into the cone of de¬pression of the shaft. Investigations in the drillholes using the DAU-3M flowmeter described in Chapter 3 showed that all of the nine aquifers were penetrated by the time a depth of 690 m had been reached. The flowmetric information showed that aquifer numbers [1 and 2], [4, 5, and 6], and [7 and 8] had practically identical hydrogeologic characteristics; so it was decided to connect them into combined stopes and inject the grout using five stopes instead of nine. Table 9.2 shows the results of the grout injection into the aquifers. The volume of grout pumped into the separate intervals through single holes varied from 204 to 15 m3. The trend of grout consumption showed a reduction of grout consump

Jan 1, 1993

By D. S. Kostick

Soda ash production in the United States during 1994 increased 4%, reaching 9.3 Mt (10.2 million st). That was the second highest production year. Domestic nameplate soda ash capacity is about 11 Mt (12 million st). Overall, the industry operated at about 85% of capacity. Some companies produced at 100% of capacity while others produced at below their design ratings. Although domestic soda ash consumption was slow during the first half of the year, third- and fourth-quarter sales increased, especially in the flat¬glass and fiberglass sectors. These two sectors increased because of greater demand for glass products in the automotive and construction industries. Soda ash sold for pulp caustic soda increased during 1994. This was due to higher prices for and reduced availability of electrolytic caustic soda. It is often preferred for pulp digestion because of its stronger alkalinity.

Jan 1, 1995