Search Documents

By Thorvald Wetlesen

Computer controlled drilling is now proven technology. It was first introduced by the development of the Furuholmen system for a prototype three boom tunneling jumbo in Norway in 1978. Now, 13 rigs with this concept are in operation in Europe, 3. in mining in England and. 10 in tunneling elsewhere in Europe. The system is also adapted to roadheader guidance. Practical experience has shown that the computer control system makes it possible to drive tunnels with a more accurate contour thus reducing the total amount of rock excavated, and where a full concrete lining is required a reduction in concrete volume is achieved. The total tunneling economy is improved. In the future we expect to see a wider range of instrumentation on jumbos, from the simple direction instruments to computer guidance systems for monitoring only, as well as fully automatic drilling to a programmed drilling pattern. More compact and reliable electronics will be available. Systems with low power consumption will fit easily into flameproof applications. Cabling complexity will be reduced by connection of sensors to serial signal lines.

Jan 1, 1989

By C. R. Stephan

The Mine Safety and Health Administration's (MSHA) Ventilation Division continues to evaluate proposed explosion-resistant seal designs. There are currently eleven specific designs for explosion-resistant seals that are suitable for construction in underground coal mines. Seal construction in operating mines must be equivalent to those constructed in the Experimental Mine during the explosion testing program. Accidental failures of seals have occurred due to explosion pressures below 138 Kpa (20 psi). The possibility exists that the failed seals were not properly constructed. Also, conditions in the vicinity of the seals may change. Water may accumulate against the seals, heave or sag may cause detrimental effects on the seals, and sloughage of the ribs may negate hitching. If seals are not properly installed or maintained, they could fail when subjected to explosion pressures. If seals fail for any reason, the possibility exists for explosion propagation throughout large areas of the mine. There could be catastrophic consequences to an event of this nature. This report will present a limited discussion on the construction of each of these seals and will address related issues.

Jan 1, 2001

By Harold Gibson

The mechanisms leading to the impact of airborne dust particles onto bluff flow obstacles have been extensively reported [1] and widely applied in dust measuring instruments (e.g., impactors) and in dust collecting devices (e.g., filters and scrubbers). If the human head is regarded as a bluff body, particles from dusty flowing air can impact onto the face by virtue of those mechanisms. While a great deal has been researched and written on the nuisance caused to human beings by the entry of dust particles into the body by inhalation through the nose and mouth, there appears to be nothing reported in the scientific literature about the irritation which can be caused by the impact of dust onto the face. And yet there is sufficient evidence to suggest that in certain working environments and under certain conditions, the problem is indeed a real (albeit subjective) one. In the coal mining industry, underground workers are exposed to conditions, involving dust-creating production and handling processes on the one hand and high ventilation rates demanded by the gassy nature of the environment on the other, in which the problem can exist. At the coal face, for example, the movement of powered roof supports ("chocks") can release bursts of dust formed by the crushing action of the supports, which in turn is entrained into the moving air and impacts onto the faces of miners working just downstream. The dust in question contains a large proportion of coarse particles which, while still fine enough to remain airborne for appreciable distances downstream of the point of release, are coarse enough to produce sen¬sation on impact with the skin. Adverse subjective response of workers to such irritation could damage morale and productivity. We have performed laboratory and field experiments to investigate the psychophysical and physiological responses of human subjects to dust impacting onto the face and into the eyes. Since this appears to be the first systematic investigation into these questions, the aim has been to construct a useful scientific framework from which to allow characterisation of the problem of such "fly-dust", and, ultimately, the development of methods for monitoring and controlling it. The main results of our research are given here; the theoretical and experimental details will be presented at greater length elsewhere.

Jan 1, 1980

By Kenneth W. Torpey, James G. Ball, Richard F. Flanagan, David S. McAllister

INTRODUCTION Under a Federal grant by the Urban Mass Transit Administration (UMTA) (80%), and sponsored by the State of New York (200), Niagara Frontier Transportation Authority is constructing a 10.3 km (6.4 mile) light rail rapid transit system in Buffalo, New York. The $450 million project, which began construction in the Spring of 1979, is unique in rail transit alignment designs in the U.S.A. and the first predominantly underground light rail system in North America. The Buffalo project is unique in that the first phase of the expandable system follows the alignment of Main Street and is on the surface in a proposed 1.6 km (1.0 mile) pedestrian mall in the downtown business district. The alignment then progresses northward into a cut-and-cover portal and standard double-box configuration for 2.74 km (1.7 miles) at a depth of 9.1-10.7 m (30-35 ft) and subsequently drops into bedrock at depths of 18.3-27.4 m (60 to 90 ft). The 5.63 km (3.5 mile) rock tunnel section consists of two single tunnels 4.88 m (16.0 ft) nominal finished diam. and includes five stations. The rock tunnel line section was divided into a north and south contract of 2 316 m (7,600 ft) and 3 243 m (10,640 ft), respectively. Due to the existing surface facilities and the future station locations, the line tunnel contracts differed considerably in their shaft access

Jan 1, 1981

By Thomas Oberndorfer

Recent publications indicate that there is a rising interest in the field of mining method selection, and increasing efforts are being undertaken to develop satisfying solutions. Yet, computer assistance for mining method selection (MMS), or in other, terms assistance in the (pre-)feasibility state of a project, still lags behind the computer application in other mining activities. This is true for research as well as for application. This paper is intended as a contribution to the development in computer-assisted mining method selection, and focuses especially on underground hard-rock mining. It is structured in four main parts. The first deals with general aspects of mining method. selection within the process of mine planning, and with problems and requirements which derive from this specific situation. In the second part some numerical MMS-approaches hitherto published are briefly introduced, and investigations on these approaches are discussed. Based on .these experiences, in the third part an analysis of the complex system MMS is presented. It focuses on heuristics, influencing factors, objectives, assessment-routines and mining methods, and emphasizes the essential necessity of a profound mining method description (MMD) specially developed for the requirements of MMS and numerical processing. Accordingly the fourth part of this paper presents a mining method description model developed at the Department of Mining Engineering, Montan-University Leoben (MUL), Austria. It describes the consequences of the investigation, in particular the new mining method description model, on 'the design of a MMS-system. The paper closes with a outlook on the possibilities of an successful MMS-system being realised.

Jan 1, 1992

By J. R. Gump

The term "rare earths" is used to designate a group of elements, Numbers 57-71 which are closely related chemically. They were called "earths" because their oxides resemble those of the alkaline earths, and the designation "rare" was originally applied because of their scarcity. Now many of these elements are known to exist in considerable quantities, and the term "Lanthanide" is applied to this group of elements, because of their similarities to lanthanum, the first element in the group. Many authorities insist on including yttrium, element Number 39, because of its extremely close association with the members of the group in nature and because of its similarity in chemical properties. It has been estimated that the combined rare earth group makes up about five-thousandth. of one percent of the Earth's crust, a higher percent than the common elements, lead, tin, zinc, arsenic, mercury, silver and gold. Cerium is by far the most abundant member comprising about half of the total amount. Yttrium, neodymium, and lanthanum are next in order; samarium, gadolinium, praseodymium, dysprosium, erbium, holmium, and ytterbium are increasingly scarce; while the elements lutetium, thulium, terbium, and europium are extremely rare. The rare earths as a group are metals, usually trivalent, forming basic oxides, and insoluble oxalates in dilute mineral acids. Their fluorides are also difficultly soluble; hence the rare earths or lanthanides may be separated, in general, from other elements by adding oxalic or hydrofluoric acid to a dilute mineral acid solution containing them. The most striking fact which characterizes these elements is the remarkable .similarity in both the physical and chemical properties of their compounds. Their main differences are in the solubilities of their salts and the basicity of their oxides, which vary between that of the alkaline earths and that of aluminum.

Jan 1, 1960

In June, 1,334 underground construction and tunneling professionals gathered in Toronto, Ontario for the 2007 Rapid Excavation and Tunneling Conference (RETC). This biennial event, sponsored by SME, is one of the global underground construction industry?s major events. And this year?s RETC was the first one that included the new Underground Construction Association. [ ] (UCA) of SME. In addition, the conference?s exhibit attracted 125 equipment and service providers. The next Rapid Excavation and Tunneling Conference is set for June 14-17, 2009 at Caesar?s Palace, Las Vegas, NV.

Jan 1, 2007

By Alfredo Menendez, Alberto Sarmentero

A B S T R A C T The Los Pijiguaos bauxite is one of the largest accumulations of trihydrate alumina ore recently discovered; it is a plateau type, with no overburden, relatively soft tertiary quartz-bearing bauxite developed on a pre-Cambrian Rapakivi Granite batholith. The deposits are found in the northwestern rim of the Guiana Shield, State of Bolivar, Venezuela, and were discovered in 1976 after a grass-roots exploration campaign. Target areas were mainly selected on the basis of geological and geo¬morpholigcal criteria, guided by correlation with known deposits elsewhere in the Guiana Shield. The vertical. lateritic profile consists of an upper concretionary zone, followed by a mottled zone, a palid zone and finally the weathered rock merging into fresh granite. The upper concretionary zone displays a cellular, pisolitic or spongy texture and contains the following minerals: gibbsite (60-90%),quartz (5-10%), hematite (5-10%), goethite (under 5%), boehmite (traces), kaolinite (traces). The gibbsite content decreases sharply downward from the lower limit of the concretionary zone and the kaolinite and quartz content increases in the underlying mottled zone. The mottled and palid zones display a pseudo rapakivi texture and quartz, kaolinite and mica are the. essential minerals.

Jan 1, 1984

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By P. E. Sperry, R. E. Heuer

The United States Bureau of Reclamation is constructing the $200 million Navajo Indian Irrigation Project to irrigate 110,000 acres of land on the Navajo Indian Reservation in northwestern New Mexico. Water from the San Juan River is impounded by Navajo Dam and will be conducted for 26 miles along a series of tunnels and canals to the area to be irrigated. Tunnel No. 3 is the third in a series of six tunnels along the route. Bids for construction of Tunnel No. 3 were received by the Bureau of Reclamation in September, 1970. Fluor Utah was low bidder at $8.7 million. Ten of the 12 bids were based on excavation by tunnel boring machine. The consulting firm of A. A. Mathews, Inc., was retained by the contractor to advise on geologic and rock mechanics conditions after support problems developed in the tunnel. Tunnel No. 3 is 15,264 feet long, has an 18 foot lined diameter, rises approximately one-half inch per 100 feet in the direction being excavated, and is 6,000 feet above sea level. There is one short curve in the alignment. Minimum concrete thickness is 12 inches with eight inches from 'A' to 'B' line making a pay diameter of 21 feet, 4 inches. The tunnel is supported with rock bolts and steel pans. Mole excavation began on May 13, 1971 from a blasted starting chamber. After 46 feet were excavated the mole was shut down and the trailing muck handling equipment was pulled into place. After advancing 1,700 feet in 34 days, unanticipated ground water conditions and ground support problems were encountered slowing moling so that the next 1,000 feet of advance consumed 97 days until December

Jan 1, 1997

By Anitava Ghosh

A computer program has been written to simulate ground vibrations induced by multiple- hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosive charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g.,velocity, attenuation, single-hole input pulse), or by back-calculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties encountered are backcalculating individual input pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shorn to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included, improved input pulse determination and propagation laws, and more detailed verifications with field results are required in order to make the program more directly applicable to practical situations.

Jan 1, 1986

By A. S. Macfarlane

Over the last few years, and especially the last few months, issues relating to Corporate Governance in industry in general, and the Minerals industry in particular, have become increasingly topical, as a result of a number of scandals and failures. The development of International and National Codes for the reporting of Mineral Resources and Reserves began some years ago, and has been followed by more stringent Listing Rules for the Securities Exchanges, as well as more standardised formats and protocols for financial reporting of assets and activities. More recently, some countries have adopted Codes for the Valuation of Mineral Properties, which have focussed on standardisation of valuation approaches to be adopted, and the qualifications of people deemed competent to sign off such valuations. This process has not been without criticism, the main criticism being the proliferation of local standards and regulations, which are often difficult to apply and regulate, or which are too prescriptive for multinational mining companies to deal with. In South Africa, these concerns have been recognised, while at the same time a need has been identified to establish a Code which could be applied to South Africa, and the African continent as a whole. Such a development would necessitate that the Code satisfies the needs of the continent, but in a global context. This global context has already been set by the activities of the International Organisation of Securities Commissions, the International Valuations Standards Committee and the International Accounting Standards Board. This paper explains the progress and process that has been established in South Africa for this purpose, and highlights the key issues which are open to public debate, so that the process is inclusive and transparent, whilst at the same time it is consistent with international time frames, and provides a deliverable product that meets the desired objectives.

Jan 1, 2004

By J. Winterton

Cripple Creek and Victor Gold Mining Co. is developing a full-scale pad injection program as part of the overall operational plan for the Valley Leach Facility. As part of the development process the mechanics of the injection methodology are evaluated in the context of physical injection measurements, outcome from geophysical monitoring, and gold leaching theory. The results indicate that hydraulic fracturing analogies advanced heretofore do not accurately describe injection phenomena in unconsolidated and noncohesive material typical of leach pads. A new interpretation is presented and extended to define operational strategies for maximizing gold production.

Feb 27, 2013

By M. Prasad, A. K. Majumder, T. C. Rao

The depletion of high-grade phosphate ores is bringing about a search for a suitable, economically viable technique that con process the abundant low-grade phosphate reserves. About 75% to 80% of the world's low-grade phosphate reserves are associated with carbonate gangue that is not amenable to treatment by the simple techniques of physical separation. The processing of sedimentary dolomitic/calcareousphosphate ore has numerous problems, including similar surface properties of the carbonate and phosphate. Two-stage reverse anionic flotation of carbonates (dolomite/calcite) has appeared to be a promising separation technique ,for the removal of carbonates from sedimentary rock phosphate. In reverse fatty-acid anionic flotation, the depression of phosphate mineral with orthophosphoric acid produces satisfactory results for calcareous as well as dolomitic phosphate ores from several locations of sedimentary origin.

Jan 1, 2000

By E. M. J. A. Pallone, F. N. Cunha, W. S. Resende, R. M. Stoll, R. C. Bradt

Utilization of the magnesium aluminate spinel in refractor' applications is briefly reviewed. The synthesis of a magnesia aluminate spinet aggregate from natural raw materials is considered in terms of the crystal chemistry of the spinet structure and expected impurities. Principles for the formation of this spinet refractory aggregate from different natural raw materials are presented. The basic concepts were then applied to the reaction of a bauxitic clay with a natural magnesite. This combination of raw materials has the potential to produce a low-cost refractor' aggregate that is a composite of spinel and forsterite. Experimental results are reported to produce a spinel refractor.' aggregate containing a small amount of forsterite. It possesses low apparent porosity and high bulk density suitable for industrial refractor' applications, including steelmaking, aluminum and copper foundries and cement production.

Jan 1, 2002

By C. Abbruzzese, L. Piga, P. Fornari, S. Ubaldini, R. Massidda

The effects of certain variables on the extraction of gold by thioureation have been investigated on a quartzose gold-bearing ore using a statistical multifactorial strategy. The factors taken into consideration were milling time (which corresponds to a given grain size), oxidant concentration, thiourea concentration and liquid/solid ratio. The influence of these four variables was ascertained first by a full factorial design at two levels for each variable (16 runs). This permitted the estimation of first-order effects of the factors affecting the process. Then 9 runs were added whose levels were both in the centre of and outside the axes of the previous plan thus originating a central composite design. This permitted estimation both of second-order effects of the factors involved and of parameters of a second-order polynomial model. The results show that extraction of gold depends only on milling time and oxidant concentration, at least in the experimental range considered. The equation fitting experimental data, as calculated by the least squares method, allows a response surface to be drawn. Due to the low gold grade of the ore (6 ppm) statistical analysis could lead to contradictory results, hence strict observance of Gy's rules for sampling and very accurate and precise chemical analyses were required.

Jan 1, 1995

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles)northeast of Winnemucca, NV (Fig. 1). The deposit is owned by Getchell Gold Corp. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 to 671 m (1,400to 2,200 ft) along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate in the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By Paul D. Tomlingson

World class performance is the ultimate objective of many maintenance organizations. It marks the organization as a leader in its industry and sets it apart as the ultimate achiever. But what is a “world class” standard and how can it be achieved? Is there a yardstick by which an industrial organization can measure the relative performance of its maintenance activity and compare it with performance levels that universally identify “world class” status? Are there financial formulas, achievements, evaluation techniques or indices that provide this yardstick?

Jan 1, 2006

By P. J. D. Lloyd

INTRODUCTION The mining of gold commenced on the Witwatersrand in 1884, and reached a mature state by about 1910, when nearly 20 million metric tons were mined. Mining has continued on the central Witwatersrand, the area of the first mining, at a similar rate until recent years. As a result, well over 1 billion tons of gold mining wastes have been dumped along a line over 80 km long, centred on Johannesburg and stretching from Randfontein in the west to Nigel in the east. (see Figure 1). The population of this conurbation, which straddles the line of mining, has grown to about 5 million. In 1922 uranium was first discovered as a constituent of the ore (and thus of the wastes). Investigations in the 1940's revealed that values near Johannesburg were low, but that, at the western and eastern ends of the central Witwatersrand line, and in the new areas centred on the towns of Carletonville, Klerksdorp and Welkom up to 200 km from Johannesburg, values were adequate to permit uranium recovery. Commercial production commenced in 1952, and by 1979 over 100 000 tons of uranium oxide had been produced. There thus arises on the central Witwatersrand nearly 1,3 billion tons of slimes containing an average of about 0,005% uranium and about 1,8% FeS2. The material grading is about 70%-75µm, and the primary mineral is silica (over 85%). The material is contained in dams constructed hydraulically. A typical dam has an area of about 100 hectares and there are over 6000 ha under slimes dams in the area of concern. The treatment of these dams for uranium recovery commenced in 1977. The situation has thus arisen whereby potential uranium ores have unwittingly been dumped in significant quantities within a major metropolis over a period of nearly a century. The purpose of this note is to review the experience arising from the potential hazard over a considerable time.

Jan 1, 1980

By Milton E. Wadsworth

The evolution of engineering education and research has been profoundly influenced by computer technology and has concomitantly followed changes in this technology. Today, virtually all faculty have access to at least two hierarchies of computers: desk personal computers and at least one echelon higher (workstations or a variety of mid-sized computers). Most faculty have access to three or even four hierarchies: the two listed, plus super-mini and super computers. The ready availability of computers at a low cost has increased dedicated and site-specific computer technology. This has permitted universities to move into the field of macro-engineering, to address increasingly complex problems in resource recovery, manufacturing and many other areas, including important societal problems, like the environment. The creation of university research centers indicates the growing importance of macro-engineering involving large systems of interactive components. Funding agencies have increasingly favored such centers since they cross disciplines, generate inter-university consortia and foster university-industry programs.

Jan 1, 1992