Search Documents

By Hassan El-Shall

The results of laboratory and pilot plant testing of a newly developed process to dewater waste slurries from different industries are presented. Data indicate that an increase in solid contents from 6% to over 30% can be obtained in few minutes retention time in comparison to several years as required by currently used technologies. The economical as well as the environmental impacts of such process are discussed.

Jan 1, 1992

By C. Peppin, H. McLoren, D. Bayer

Hecla Mining Company and Master Builders Inc. conducted a study to evaluate the use of admixtures in reducing backfill binder concentrations. Additionally, admixtures were evaluated to help mitigate the occurrence of cold joints in the fill. Initial results demonstrated a 20% reduction of cement was possible while maintaining critical strength and flowability criteria. Admixtures also helped to control the formation of cold joints in backfilled areas.

Jan 1, 2001

By Edgardo I. Cifuentes, Andrew L. Mular, Andrew Burkert

Experimental designs are data acquisition plans which, if followed exactly, will quickly provide process engineers with information to assess statistically the individual and joint influence of factors on responses to permit of rapid decision making. Methodology employed to construct data acquisition plans is described in some detail. In production environments, factorial designs are appropriate for most purposes. Use of two level factorials to make decisions is described for a grinding circuit.

Jan 1, 1991

By J. M. Mutmansky

Procedures for the determination of the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques has been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the multitudinous mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the solution of problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To establish a major simplification in the development of procedures for the determination of the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1984

By H. Dr. Boldt, J. Dr. Henneke

PREFACE In German coal mines the application of tunnel boring machines has become a very effective and economic technique for major development works. After initial trials around 1970 the breakthrough was reached by driving 13 km of road ways on Rheinland and Friedrich Heinrich collieries, using a DEMAG tunnel boring machine of 6 m diameter. INTRODUCTION The coal mines of Rheinland and Friedrich Heinrich are to be found in the West of the Ruhr Area, the largest coal mining area in the Federal Republic of Germany (Table 1). They form part of the Ruhrkohle company. Rheinland coal mines produces 41000 to 43000 t of run-of-mine coal every day, of which 20500 t are usable coal. Friedrich Heinrich has a daily production of 17000 t of run-of-mine coal, 9000 t of which are usable. The coal is worked at depths of 600 to 1100 m in seams 0.6 to 3.0 m thick. The method of mining is longwall, and the machines used are ploughs and shearer loaders. From 1973 to 1980 a programme was put into operation in these two mines to develop and open up the coal field on the 885 m level. A total tunnel length of 20 km was to be driven. After thorough investigations it was decided to employ a full-face tunnel boring machine for

Jan 1, 1981

By Richard C. Sale

INTRODUCTION The topic of the paper is to discuss the use of micro computers in the construction industry. I will first discuss the present situation of the PCs in our industry followed by a discussion how Guy. F. Atkinson has integrated the PCs into it's organization. I will close with some general comments that any organization should review in order to enhance the use of their PCs both at the job sites and home office locations. PRESENT SITUATION OF THE PCs IN OUR INDUSTRY Today, the possible number of combinations that can be obtained when bringing together the available models of PCs, with their peripherals and software, is astronomical. With this array of equipment that can be bought, plus the new and possibly better equipment that is being put on the market almost daily, it is indeed a very difficult task for an organization to know how to invest its money in computer equipment. At the job sites, the work is fast paced with little time available to fully learn what the PCs can do to help with the required paperwork. I am still waiting for the day when someone has to tell the superintendent at the job site that he cannot start pouring concrete or shoot the next round because no one can get the computer to work.

Jan 1, 1987

By R. Parkins

This paper will discuss a method used to refine the fill level, and orifice size for a dual motor conveyor drive with extended delay chamber fluid couplings. The subject conveyor is located on the surface at the Mountain Coal Company West Elk Mine, located near Somerset, co.

Jan 1, 1996

By S. K. Kawatra, Harrison R. Cooper

In the last 30 years, on-¬stream slurry analyzers have proven to be of great use in the control of mineral processing circuits. This review discusses the two most popular methods, x-ray fluorescence and neutron activation analysis, and also considers techniques which are still under development.

Jan 1, 1986

By Reno M. Tonsi, Bill Raley

Supervisory Control and Data Acquisition (SCADA) systems are important tools in providing more efficient and profitable operations for the mining industry. This paper touches on the different types of equipment used in SCADA applications and discusses the benefits obtained in using Programmable Logic Controllers in this application.

Jan 1, 1989

By Heinz Hofmann

In order to drive tunnels with low overburden in town regions, it is necessary to give a quantitative prognosis for the deformation of the underground as well as of the tunnel-lining and of its stability. These problems and their solutions are illustrated by the works for a two-track-railway-tunnel in Bochum (Ruhrdistrict). In this case the most important problems consisted in passing below buildings in a vertical distance to the fundamentals of only 3.20 m and a railway earthdam with rapid train traffic in a distance of 4 m under the dam. The results of measurements from other comparable tunnels and finite-element-computations were used to prognose the settlements on the surface and in the ground, their distributions and their development in time. To obtain these values at the site, a special system of tunnel driving was executed. The tunnel was excavated with the newest type of tunneling-machine from DEMAG, cutting an inclined front, immediately followed by a special temporary support of shotcrete and inclined steel-ribs. By using theoretical and empirical methods to assess the behavior of the tunnel and underground and by executing an optimal driving system in technical as well as economical aspects, the expected behavior, expressed in quantitative values, was almost equivalent to those received by control measurements.

Jan 1, 1974

By J. Peck, M. J. Scoble, C. Hendricks

This paper is based on field studies in North American surface mines. The work involved the adaptation of microprocessor-based instrumentation to monitor various operating parameters on-board rotary blasthole drills and mining shovels. Following a review of instrumentation and monitoring methodology - drawing on experience gained under field conditions-the paper will focus on the application of monitoring technology within the framework of an Integrated Equipment Monitoring System. Such a system will permit real-time performance evaluation of key equipment involved in surface mine production. Drill performance monitoring has been demonstrated through work to date, to provide significant input into blast design, reserve estimation, mine planning and production control processes, through an improved facility for ground characterization. Monitoring excavation equipment has been proven valuable in assessing how effectively the input from drill monitored data has been used in the evolution of blast designs. This specifically refers to assessing blast efficiency through measuring associated levels of excavator performance in relation to muckpile characteristics. The medium-term goal of equipment instrumentation and monitoring has been to assist mines in optimizing the overall rock breakage and handling process. Based on the reported results, this has been accomplished. Long-term efforts now concern using a greater understanding of equipment performance and response to varying operating conditions as a foundation for the implementation of mining automation.

Jan 1, 1993

By S. S. Peng, V. Z. Sun

One of the major concerns of ground control in a coal mine is the prevention of roof, pillar and floor failures of the mine entry. To better design and evaluate the stability of a mine entry within a certain level of confidence, a reliability approach is introduced. The advantage of using the reliability approach, rather than the conventional safety-factor (SF) method, is that it not only takes variability of both rock/coal properties and stress into consideration but also assesses the stability of each component and the mine entry as a whole. Therefore, it is anticipated that by using this approach the current ground-control technology in a coal mine will convey a better sense of confidence. The results of a case study show that there is a significant difference in mine entry stability between the current design method and the reliability approach.

Jan 1, 1999

By W. J. Stone

In response to concerns over the impact of mining on the hydrologic balance at the Navajo Mine in northwestern New Mexico, a recharge study was conducted using a chloride mass- balance approach. Impact of mining on annual recharge volume was assessed by comparing pre- and post-mining recharge values. The mean regional recharge rate for reclaimed ground (weighted by acreage) is 1.02 mm/a (0.04 in. per year) or twice that for undisturbed ground, 05 mm/a (0.02 in. per year). Comparison of regional recharge volumes for identical areas shows mining increases recharge 92%. The increase is only 80% if no closed depressions are constructed during reclamation. However, the increased rates are so low that there should be no detrimental impact on regional water resources. The chloride method proved useful at Navajo Mine and should succeed at others surface coal mines as well.

Jan 1, 1991

By R. L. Murray-Smith, M. E. A. Robertson, M. J. Prosser

The AZTEC is an automated instrument, for the non-destructive analysis of gold ore samples, which uses energy dispersive X-ray fluorescence (XRF), This is achieved by X­ray tube excitation of gold K X-rays. The first production instrument was commissioned at Vaal Reefs Chemical Laboratory (VRCL) in November 1987, followed by two second generation instruments in 1989. AZTECs have also been installed at Western Deep Levels and at Anglo American Research Laboratories (AARL). A further unit is being assembled at Ashanti mine, Ghana. At VRCL the AZTECs are used primarily for the evaluation of mine (stope) samples. Each of the production instruments can routinely analyse 650-700 samples per day, with the aid of a robotic sample transfer system. Various techniques have been evaluated for increasing sample throughput. For example, higher value samples can be counted for a shorter time to obtain the necessary relative precision.

Jan 1, 1991

By J. A. Slattery, C. E. T. White

Although trace amounts of Indium are found in many ores, commercial production of the metal has come almost exclusively from residues, flue dusts and slags generated by Zinc recovery operations. Our paper attempts to summarize the various approaches used to recover Indium from these by-products. Some comments on production and price trends are Included as well as our views on future availability.

Jan 1, 1983

By Surendra K. Mishra

Recent land ban act has put pressure on industry to decontaminate the waste streams before they could be discharged. However, for both metal and organic contaminated wastes, there are commercial incentives to recover usable resources. Recent technology developments have helped meeting such objectives. This paper reviews developments in treatment technologies for industrial wastes. Major chemical groups used in waste treatment are summarized.

Jan 1, 1994

By S. K. Kawatra, S. J. Ripke

Iron ore pellets use bentonite clay as binder at dosages from 0.5to 1.0% (10 to 20 pounds per ton) of moist iron ore concentrate. Bentonite is typically shipped hundreds of miles from Wyoming to the Lake Superior iron ore district. It is therefore best to know how effective a bentonite will be before it is shipped and used to bind concentrate into pellets. Current tests of bentonite effectiveness include: plate water absorption, methylene blue uptake, free swell, exchangeable cations, and glycolated layer expansion. However, these tests have many disadvantages: First, they only measure the ability of a bentonite to expand, disperse, or absorb, not how well it will bond. Second, most of the tests require up to 20 hours to perform. Bentonite only has a few minutes to interact within the concentrate before it is indurated (sintered). These long-term tests may not reflect the true behavior of bentonite. Third, the tests are tedious and often results are inconsistent between different iron ore concentrates, labs, and technicians. Fourth, some of the testing equipment is difficult to procure. Fifth, procedures are often difficult to standardize. In this paper, the Binder Effectiveness Strength (BESt) test to evaluate binders for iron ore pellets is presented that: measures the ability of bentonite to bond, requires only about two hours to complete, is simple and reproducible, and utilizes readily available equipment that has been standardized for decades.

Jan 1, 2003

By Mehmet Mesutoglu, Ihsan Ozkan

This study investigates the feasibility of rock bolting support in an underground coal mine gallery with a thick coal seam. The Ömerler underground coal mine working area, owned by West Lignite Enterprise of Turkish Coal Enterprises, was selected for this purpose. Longwall top coal caving is implemented as the production method in the Ömerler underground coal mine. Field and laboratory studies were conducted to determine rock mass and rock material properties, followed by experimental, empirical and numerical analyses based on the acquired data. The obtained design results were evaluated using a resin-grouted rebar rock bolting (RBR) system and steel arch support (SAS) pilot application areas. The numerical modeling results conducted using the fast Lagrangian analysis of the Continua 3D (FLAC 3D v6.0) program indicated less displacement and secondary stress change in the RBR-supported zone compared to the SAS-supported zone. In situ measurements also demonstrated that RBR provided more successful support to the roof during coal production activities. The findings suggest that RBR is a more effective solution when evaluating the feasibility of rock bolting support systems in underground galleries with thick coal seams at the Ömerler Mine. This study emphasizes the importance of more sustainable and safe support systems to enhance operational efficiency in the coal mining industry.

Mar 1, 2025

By Y. C. Kim

One aspect of long-range mine planning in an open-pit mine is first to define the ultimate pit limit, i.e., the projected size and shape of the pit at the end of its life. This chapter is concerned with various techniques that are currently in use today in determining the ultimate pit limits using the computer. Prior to the early 1960's, open-pit limits analyses were entirely performed manually. This manual technique has been well explained by Soderberg and Rausch in Surface Mining (1968). Soderberg and Rausch also explain clearly the need for establishing the ultimate pit limits in long-range mine planning, i.e., location of surface facilities, dumps, etc. Consequently, the need for ultimate pit limit design will not be reiterated here. Nor will the definitions of the most commonly accepted terminologies such as break-even stripping ratio, economic cutoff grade, ultimate and working slope angles, preproduction stripping, etc. be repeated here. Briefly, the objective of the ultimate pit limit design (which is also frequently referred to as pit design in short) is to determine the projected final pit limits of an ore body and its associated projected grade and tonnage, which will maximize some prespecified economic criteria while satisfying practical operational requirements.

Jan 1, 1979

By Kostas Fytas, Sebastien Perreault

This paper presents EOLAVAL, an integrated mine ventilation design software. In its new expanded version it is a user friendly and fully interactive computer package. The features of the new version are a graphics interface fully compatible with Autocad files, an integrated database of fan characteristics and the optional use of the thermodynamic approach in carrying out network simulations. This software can be used in underground mine ventilation planning: mine ventilation network analysis and simulation, economic design of airways, auxiliary ventilation design, calculation of a mine air heating plant, and evaluation of the natural ventilation and pressure losses in a mine shaft. This paper presents a case study illustrating the use of the computer package in mine ventilation design.

Jan 1, 2002