Search Documents

By LUKAS FAHLE, JURGEN F. BRUNE, ANDREW J. PETRUSKA, ELIZABETH A. HOLLEY, Gabriel Walton

Adverse ground behavior events, such as convergence and ground falls, pose critical risks to underground mine safety and productivity. Today, monitoring of such failures is primarily conducted using legacy techniques with low spatial and temporal resolution while exposing workers to hazardous environments. This study assesses the potential of novel simultaneous localization and mapping (SLAM)-based light detection and ranging (lidar) data quality for rapid, digital and, eventually, autonomous minewide underground geotechnical monitoring. We derive a comprehensive suite of quality metrics based on tests in two underground mines for two state-of-the-art mobile laser scanning (MLS) systems. Our results provide evidence that SLAM-based MLS systems provide data of the quality required to detect geotechnically relevant changes while being significantly more efficient for large mine layouts when compared to traditional static systems. Additionally, we show that SLAM-specific processing can achieve an order of magnitude better relative accuracy relevant for change detection than quality metrics derived from traditionally deployed tests would suggest, while reducing SLAM-drift error by up to 90 percent. In collaboration with an operating block-caving mine, we confirm these capabilities in field tests on a minewide scale and, for the first time, demonstrate methods of rockfall detection using MLS data. While more work is required to investigate optimal collection, processing and utilization of MLS data, we demonstrate its potential to become an effective and widely applicable data source for rapid, accurate and comprehensive geotechnical inspections.

Jan 1, 2023

By J. A. M. Cano

With a view toward increasing its product competitiveness in the foreign market, SAMARCO MINERACAO S/A has developed high MgO type pellets at its pilot plant for performing direct reduction simulation tests. Additives such as dolomitic lime and magnesite were used for increasing pellet MgO content. Comparative direct reduction simulation tests were conducted both in SAMARCO and foreign laboratories. The test results showed that it is possible to produce direct reduction type pellets with satisfactory metallurgical properties, which can be successfully processed at increased temperatures in direct reduction furnaces.

Jan 1, 1992

By K. A. Natarajan, K. Karthiga Devi

"A biodegradable flocculant was produced during growth of Bacillus megaterium. The major component of the bioflocculant was found to be a polysaccharide composed of some proteins. Fourier transform infrared (FTIR) spectra analysis revealed the presence of carboxyl and hydroxyl groups in the bioflocculant, and thermal characterization by differential scanning calorimetry (DSC) showed the transition and crystalline melting point at 90-105°C. The effects of bioflocculant dosage and pH on the flocculation of mineral suspensions were evaluated. The bioflocculant exhibited good flocculating capability on mineral suspensions and achieved flocculating efficiencies of 90 percent for kaolinite and 85 percent for hematite suspensions at a dosage of only 5 mL/L. The maximum arsenite removal was found to be 90 percent at a bioflocculant dosage of 2 g/L, which is better than traditional chemical flocculants. This study demonstrates that microbial bioflocculants have potential for application in environmental cleanup, such as in the flocculation of mineral fines and in the remediation of solutions that contain toxic heavy metals.IntroductionBioflocculants are biopolymers produced by microorganisms during their growths. The predominant components of a bioflocculant are extracellular polymeric substances such as glycoprotein, protein, cellulose and nucleic acid (Salehizadeh and Shojaosadati, 2001). Bioflocculants have gained much wider attention due to their biodegradability and safety. In recent years, the study of bioflocculants has attracted wide attention. Bioflocculants can be nontoxic, harmless and eco-friendly. Normally, they exhibit different functional properties, serving as stabilizer, dispersant or thickener. Among these properties, flocculation is of major interest. For example, Phormidium sp. strain J-1, isolated from a drainage channel, exhibited excellent flocculation activity for bentonite particles in liquid suspension (Fattom and Shilo, 1984). A protein bioflocculant produced by Rhodococcus erythropolis could efficiently flocculate suspended solids while losing their flocculating activity by enzymatic digestion (Kurane et al., 1994, Takeda et al., 1991). Klebsiella sp. strain S11 screened from activated sludge was unable to flocculate without the addition of calcium chloride (Dermlim et al., 1999)."

Jan 1, 2015

By Caroline Gerwig, Joseph R. Wickline, Zach Agioutantis

In longwall mining, the progressive caving of the roof allows stored energy to dissipate over an extended time. However, in some cases, the roof strata above the longwall panel are unusually strong and do not break with the movement of the working face. Instead, the roof material bridges over the expanse of the longwall, forming an unstable beam. Later, when this beam breaks, the stored energy can release suddenly, causing a seismic event to propagate to surrounding mine workings. The focus of this paper is to estimate the size of beams that form over longwall panels to the seismic energy recorded by the mine. Analytical calculations are used to verify two-dimensional models of longwall roof beams to determine the strain energy and gravitational energy developed, which is then released upon strata failure to surrounding mine workings. Models are developed using RS2 to model the stress, strain, and deflection along the bottom of the longwall roof beam to calculate gravitational and strain energies. Gravitational energy is shown to be the main driving factor in energy release, except for the beams with low heights. Analyses allow the determination of beam characteristics based on seismic data. The analysis is refined using swelling factor to compare various beam drop heights. The models show an increase in seismic magnitude for higher drop heights. However, the actual data provided by the Buchanan mine displays a decrease in seismic magnitude with increasing drop height, indicating that energy is dissipated into the broken gob material as drop height increases.

Jul 1, 2023

By L. Yuan, J. H. Rowland, R. A. Thomas

Hydrogen (H2 ) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system. In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, H2 concentrations in the airflow are constant, while in the full-scale experiments, increasing H2 concentrations generated as a byproduct of charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to safeguard underground miners.

By Ralf Winterberg, Axel G. Nitschke

"Macro synthetic fiber reinforced concrete or shotcrete is seen by many design engineers as offering a viable alternative to steel reinforcement in tunnel linings. The technology is now commonplace for primary and permanent ground support in both mining and civil tunnel applications. It has for instance become the standard form of reinforcement in the Australian mining industry, and has been used for a majority of permanent tunnel linings in recent tunnel construction in Norway. Similarly, macro synthetic fibers are becoming a standard solution for the initial lining in the USA.The use of macro synthetic fiber offers innovative solutions, yielding robust and sustainable tunnel lining designs. Citing recent research and actual projects, this paper presents state-of-the-art design considerations for fiber reinforced tunnel linings relating to structural and long-term performance. Topics include seismic resistance, crack width control, corrosion and durability, as well as sustainment of performance with age.INTRODUCTIONMacro synthetic fiber reinforced concrete (MSFRC) and shotcrete (MSFRS) has reached maturity as an engineered material and is widely used in all forms of tunnel linings, for temporary as well as permanent ground support in both, mining and civil tunnel applications. In the Australian underground mining industry, it became the standard form of reinforcement, where 2014 literally marked the end of steel fiber use in shotcrete [1], and has been used for over 80 percent of permanent tunnel linings in recent tunnel construction in Norway. Similarly, macro synthetic fibers are becoming a standard solution for tunnel initial linings in the USA. Recent examples in civil tunneling are the Devil’s Slide Tunnel and Caldecott Fourth Bore Tunnel in California or the Anacostia River Tunnel Intershaft Connector Tunnel in Washington D.C. In addition, an increasing number of tunnels are adopting shotcrete permanent linings using macro synthetic fibers. Examples include the A3 Hindhead tunnel near Guildford in the UK and the North Strathfield Rail Underpass in Sydney, Australia [2, 3]."

Jan 1, 2016

By Dan Norrgran

In recent years, a great deal of attention has been focused on developing mill liners to increase wear resistance, improve grinding efficiency and reduce energy consumption in milling applications. The installation of an appropriate mill liner is critical as it affects the overall cost and product quality. A mill liner has two specific functions. The first is to protect the mill shell and mill ends from direct contact with the abrasive grinding media (in this case, the liner serves as a wear surface). The second function is to transport the grinding media, creating energy for size reduction. The liner acts as a lifter, mechanically transporting and cascading the grinding media. The mill lining is a major cost in the milling operation. The costs associated with the mill lining include the capital cost of the lining, downtime required to replace the worn liner and the labor for installation. Generally, in hard rock mining, the life of a mill liner in secondary ball mills is 12 to 24 months.

Jan 1, 2009

By John W. Lane

Climax Molybdenum Company, a Division of American Metals Climax, Inc., operated a hydrometallurgical plant* at Climax, Colorado from August 1966 through August 1968 to recover molybdenum from a mixed oxide and sulfide ore. The ore treated for this addition to the existing plant contained sufficient Molybdenite values to be mined for Molybdenite recovery alone, so that the oxidized molybdenum recovery could be regarded as a byproduct operation. Climax is located at an elevation of 11,300 feet. All process equipment, except thickeners, was enclosed in buildings. Annual snowfall is approximately 250 inches per year. Paved highways and rail service to the plant are maintained and kept open all year. Most of the employees live in the town of Leadville, which is approximately twelve miles from the plant site. The sulfide flotation plant handles 40,000 to 45,000 tons per day of ore. The mine is one of the world's largest underground mines.

Jan 1, 1971

By K. H. Nimerick

Froth flotation of coal is growing in importance and complexity. Some of the reasons for these changes follow. 1) A need exists for energy resource conservation. 2) Preparation plants are processing widely varying coal -- deep seam, strip and stockpiled either separately or as blends. 3) More fines are being generated because more mines are using automatic mining equipment. 4) It is more practical and economical to remove ash and sulfur at the preparation plant than during utilization.

Jan 1, 1982

By E. D. Sehnke

The refractory materials industry provides the largest commercial market for nonmetallurgical grade bauxite. Refractory grade bauxite is prepared from bauxites having low iron, titania, and alkali content by calcining at temperatures near 1,650° C. Although there are substantial bauxite reserves in the world, premium grade bauxite ores suitable for use in refractory applications are limited to only a few specific sources, primarily in Guyana and the People's Republic of China. Consumption of bauxite for refractory use is closely associated with the production and consumption of primary metals, in particular iron and steel. Barring major disruptions within the principal producer nations, sufficient supplies of refractory bauxite will be available to meet world demand well into the next century, and raw material costs will continue to determine the availability of markets for bauxite-based refractory products.

Jan 1, 1992

By Adeyemi Adesina, Subhabrata Mishra, Syed Mohammed Mustakim, Malaya Kumar Jena, Shaswat Kumar Das

Utilization of low-grade manganese ore adopting the carbothermic reduction roasting process is a proven method to produce high-grade manganese ore. To minimize industrial waste and protect the environment, gas cleaning plant sludge (GCPS), which is a solid waste from steel industries, was employed as a reductant to perform the reduction roasting process. The optimum conditions to carry out reduction roasting of the low-grade manganese ore were found to be: a roasting temperature of 950 °C, a residence time of 2 h, 40% GCPS as reductant, and magnetic separation at 5000 G for a manganese ore size of –10 mm. A lowgrade manganese ore comprising Mn grade 31.27% and Fe grade 19.78% having a Mn/Fe ratio of 1.58 containing a high silica content of 26.48% was used for the carbothermic reduction roasting having mineral phases of pyrolusite (MnO2) and hematite (Fe2O3) as found from XRD. The gangue minerals were separated during the magnetic separation, and the upgraded product was obtained, which reached a maximum value of TMn 49.5% with RMn 76.55% and TFe 62.19% with RFe 42.51%. In the study, activated charcoal (AC) was also taken as a reductant for comparative analysis; the experimental results revealed that GPCS performed better than that of the AC, showing potential to be used as a reductant in metallurgical industries. However, the resultedMn/Fe ratio was very low for the reduced sample; therefore, it can be used for smelting along with high-grade manganese ores as a feed.

Mar 5, 2021

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By J. Morris

Petro-diesel is a common collector for fine coal froth flotation but partitioning of diesel range organics (DROs) in process streams has not been widely studied. Preliminary research suggested that under normal dosing schemes total residual DRO in process waters should be limited to the sub-ppm water-soluble fraction (WSF). Further, polycyclic aromatic hydrocarbons (PAHs) should partition proportionately with DRO. The purpose of this study was to confirm these findings in laboratory flotation tests. Total DRO and specific PAHs were measured in tailings and concentrate streams, and coal recovery and ash rejection were tracked. Results show that concentrate waters consistently had higher DRO than tailing waters, and DRO in both streams generally increased with increasing diesel dosage. DRO again appeared to be limited to the WSF and PAHs tended to partition proportionately with DRO. Results indicate optimal flotation performance should generally coincide with minimal DRO partitioning to process waters. Under typical operating conditions residual DRO should not present an environmental concern; however, conditions should be avoided that allow significant overdosing of diesel.

Feb 23, 2014

By A. J. Plumpton

Centrifugal air classification and li-quid-phase sedimentation are the principal methods of industrially sizing materials of dimensions smaller than those handled by screens. Increasing application of materials such as composites and high performance ceramics has furthered the need for closely-sized, fine, industrial mineral and synthetic products of controlled properties. Sedimentation can be used to separate very small sized particles but introduces problems of liquid-solid separation, de-agglomeration and drying. Some of the advantages and limitations of centrifugal air classification will be discussed and laboratory and plant measurements using centrifugal machines will be presented to support the discussion.

Jan 1, 1990

By B. K. Cantrell

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989, which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This paper reviews present diesel emission standards, available diesel exhaust aerosol measurement techniques, and the results of the occupational exposure surveys. In the surveys, diesel aerosol was emphasized because it is a major component of diesel exhaust, is suspected to contribute to the health hazard, and is readily measurable. Three primary aerosol measurement techniques were used: respirable combustible dust, size-selective sampling, and measurement of the elemental carbon fraction. Occupations surveyed included mine workers, railroad workers, forklift operators, fire fighters and truck drivers. The studies found mean diesel aerosol concentration levels in the range of 0.004 to 1.74 mg/m3? Highest aerosol exposures were in confined spaces such as mines where heavy diesel equipment is used. Polycyclic aromatic hydrocarbons typically are found at very low concentration levels and are not unique to diesel exhaust.

Jan 1, 1996

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of U.S. coal mining companies are beginning to develop coal seams previously thought to be coo deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas contained in coal beds increases with depth, and ventilation requirements are much more stringent for deep underground coal mines than for shallower mines. When the longwall mining method is used at great depths, ventilation, ground control, and operational considerations must all be addressed in the design of longwall panels. This paper examines the influence of these factors, particularly ventilation and operational considerations, upon the feasibility of two, three, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1986

By Jim V. Rouse

Adverse water-quality impacts of uranium mining and milling activities on both surface- and ground-water resources in the Grants Mineral Belt have recently been documented.1 In some cases, the impacts resulted in violation of existing regulations and license conditions and have endangered public health. Unfortunately, industry-sponsored ground-water monitoring programs do not adequately record the actual impacts of mining and milling on ground-water quality.

Jan 1, 1976

By Martin Langenderfer, Catherine Johnson, Alexander Douglas

Mine haul roads degrade rapidly due to extreme loads on suboptimal construction materials. Unmanned aerial vehicles (UAV) are suited to quantify large-area road-network conditions, such as surface roughness, defects and grade to optimize remediation of poor conditions and reduce overall costs. Mine haul roads present unique challenges, such as material type and edge characteristics, to automatic road detection that often fails, requiring manual road input. This research work proposes a new method using the road center determined by the principal curve of a haul truck’s path. Analysis grids were created from this center line. A dense point cloud from UAV photogrammetry was generated and multiple linear regression analysis was conducted on each individual grid. The root-mean-square error in each grid indicates the surface roughness, and the change of slope between grids indicates the road grade inconsistencies. This method was applied to 26 road sections, and the results were validated by images taken from the truck operator’s vantage point. Critical defects were identified including excessive pothole formation, corrugation, depressions retaining water, and narrowing of travel lane. The results demonstrate this is a valid method of road identification and quantification of road defects at a mine site.

Apr 1, 2024

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the USA. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before firing to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150,000 metric tons of barite in both 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender, or weighting agent in products such as paints, plastics, and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, add weight to rubber mud flaps on trucks, and add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around x-ray units in hospitals, nuclear power plants, and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses account for an estimated 78,000 tons per year in the United States. Another barite use was patented in 1926 by the oil industry. In this patent, barite is primarily used as a non-abrasive weighting agent for drilling for oil and gas exploration and production. As a weighting agent, it provides the downward force in a water based or oil based drilling fluid for cutting through rock with a tri-cone diamond drill bit. In order to minimize the wear on the drill bit and drill stem, minimum abrasion of the weighting agent is preferred. In recent years in the USA, 95% of the barite produced and about 80% on a world basis are used as a fluid weighting material during the search for oil and gas. During the latter part of the 20th century, barite was used in the drilling mud of oil and gas wells, particularly for wells deeper than 2000 meters, and petroleum well drilling demand for barite became the mineral?s major end use during economic expansions after World War II and subsequent increased use of oil and gas in the USA. The profitability of oil and gas production had a strong effect on the number of drill rigs and consumption of barite. The United States was the leading petroleum well drilling country starting in 1970, reaching 4,530 drill rigs in December 1981, and was the largest consumer of barite. In the USA, record highs of about 2.6 million tons of barite produced and 4.3 million tons consumed were reported in 1981. From 1997 to 2006, barite production declined from 662,000 to 589,000 metric tons. However, USA imports increased from 1,470,000 to 2,530,000 metric tons for lump barite. World production of barite increased from 6,780,000 to 7,960,000 metric tons during the same period. Table 1 (see Appendix) lists USA production, imports and exports and world production from 1997 to 2006. Major sources of imported barite include China, India and Morocco. Table 2 (see Appendix) lists the USA imports and price of barite by country. China, India and Morocco are the three largest exporters of barite to the USA and the world. Vietnam is a new producer, beginning in 2006. IMPACT OF CHINA ON DRILLING GRADE BARITE In the 1970s or before, China began supplying barite to the world drilling market in order to help develop their economy. When China first entered the barite export market, their high production volume, low pricing and low ocean transport expenses to the Gulf Coast forced barite producers in the USA to supply only regional markets, such as Battle Mountain Nevada barite for the western and Rocky Mountain states and Canada. Until recently, it was China?s government policy for domestic consumers to use barite below the API 4.20 specific gravity specification, leaving higher grades for export, but this is no longer the case. In recent years the internal demand for barite in China increased tremendously as their economy rapidly developed. China reduced their former 15% VAT tax rebates to 5% for Chinese barite producers, and then eliminated all VAT tax rebates on December 15, 2006. On the supply side, some high-grade barite deposits in China have been depleted. In particular, the low heavy metals sources are less plentiful. Additional mine capacity is being developed, but the new mines are underground and therefore costs will be higher. China?s appetite for other raw materials has tied up a large portion of the world?s bulk vessel fleet, including Panamax vessels (preferred for barite ore transport). Ocean transport freight rates have increased in recent years, and receiving ports in the USA are congested with imports of higher-added-value products. The Panamax Index, which tracks maritime shipping rates, more than doubled in 2006. China has also devalued its currency from RMB8.30 to RMB7.80 per dollar. These factors are driving up the import price of crude and ground barite for drilling. In addition, in the USA, rail congestion and high fuel prices led to higher trucking rates, increasing the delivered cost of ground barite to oil customers. India is the second largest supplier of crude barite to the USA and world drilling market. It produces all of its barite from a single deposit in the Cuddapah region of Andhra Pradesh State. More than 90% of production comes from the State-owned Andhra Pradesh Mineral Development Corp., and the government continues to closely control production, export volumes, and prices. India saw a dramatic increase in barite prices as a result of its last 3-year tender in 2004. However, in 2004 and 2005 their shipments of crude barite to the USA were not significant. In 2005, India began supplying barite pulverized to meet API specifications to the Gulf Coast. In 2006, Indian production was reduced owing to severe flooding in November 2005 that curtailed mining until mid-April 2006. Morocco has been the third largest supplier of crude barite to the USA and world drilling market. In 2003 and 2004 their shipments of crude barite to the USA were not significant. In 2005, Morocco resumed shipment of crude barite to the Gulf Coast and began supplying barite ground to meet API specifications to the Gulf Coast.

Jan 1, 2009

By Yuting Xue, Khaled Mohamed

Rib control is a critical component of underground coal mining operations, and comprehensive rib support design is essential for ensuring the safety of miners. However, there is currently no standardized approach for rib support design in the United States. To tackle this issue, the National Institute for Occupational Safety and Health (NIOSH) has developed a standalone application, Design of Rib Support (DORS), for rib stability assessment and rib support design under development load. The rib support design in DORS starts with the rib support density, which is determined from the unsupported rib factor of safety (RibFOS). The relationship between rib support density and unsupported RibFOS was obtained from the collected field data. The objective of this research is to validate DORS rib support design by analyzing the extent to which the proposed design capability was utilized to support the coal ribs using numerical simulations. A series of numerical models with varying overburden depth and rib height were built and the ribs were supported with the DORS-recommended rib support design. The bolt load was analyzed under different conditions and the results show that bolt load varies with the overburden depth, the location of the bolt and bolt length. The load in the bolt(s) increases with the reduction in unsupported RibFOS. The bolt(s) start to yield when the unsupported RibFOS falls below a threshold value of 0.8 and secondary support is necessary.

Jun 25, 2024