Search Documents

By Dr. -Ing. Rainer Alles

Introduction Belt conveyors usually run in a straight line. The correct alignment is a major criterion for reliable functioning and optimum running properties. Any misalignment of the conveyor, especially mistracking of the belt, can have many negative effects. As a consequence of this, damage can occur on the belt and conveyor, some material can he thrown off at the edges and serious running problems can arise. In the worst case the belt can come off its supporting structure so that operations are brought to a halt. The absolutely straight alignment of a belt conveyor is actually impossible so that on closer observation every belt conveyor contains more or less sharp curves. Whereas on non-movable conveyors the deviations from the straight can he kept within the range of practical measuring accuracy by careful installation, movable conveyors in surface mining or belt systems in difficult terrain often contain curves that are easy to see with the naked eye. Below ground, too, alignment cannot always achieved to a desirable extent or is changed by geological faults over the years. Despite these unwanted curves, most belt conveyors perform their function reliably. In view of the belt tension, the belt tends to take the easiest path. This in general is the shortest distance between the pulleys on which the belt is tensioned and bent. This means for example that for a curve radius of 10,000 m over a flight of 100 m the greatest deviation from the ideal line is as much as 12 cm. And a figure of this magnitude cannot normally he accepted. In such cases, use is made of guide devices to properly train the belt if it doesn't center itself anyway. If it's possible to control the belt position over such unwanted curves. it can also he expected that the belt tends to follow the desired curved path within certain limits. I'd now like to cite a few examples to illustrate the ways and means of guiding a belt conveyor in curves. Cost-effectiveness The advantages of belt conveyors, in particular for longer conveying distances and mass flows have been known and undisputed for some time. However, there are often obstacles standing in the way of the concept of straight routing. If a belt conveyor is to bypass elevations or existing buildings or to follow the seam of underground deposits or a predetermined path, then substantially tighter radii and longer curves are desirable or necessary.

Jan 1, 1993

By Dan Xu, Song. Gaofeng, Zhen Wei, Zhihe Wang

"With decades of development and exploitation of coal resources, the first batch of coal-based cities in China are faced with the challenge of economic shrinkage and environment deterioration due to the rapid resource exhaustion and single industrial structure. Nowadays, as a policy instrument for sustainable development, a nationwide circular economy mode has been implemented during the design and planning of new coal mines to address the challenges arising from economic depression, energy shortage and environmental pollution. It should be mentioned that several national coal bases and most of constructing and planning coal mines are located in the underdeveloped areas in the Midwest of China which means that the distance between supply source for energy resources and the demand market is significantly increased. Moreover, the eco-environment vulnerability in these rural areas should be taken into serious consideration. Therefore, after comparison and analysis with several successful coals based and diversified circular industry chains, this paper presents a case study on the circular economy park (CEP) in the northwest of Shanxi Province. Through discussion and evaluation of ‘1+3’ mode in the CEP, this paper aims to enhance the understanding of coal mine sustainable development and shed light on the relationship between resources exploitation and local economic development.1. Introduction Earth's fossil energy resources are crucial to both economic prosperity and human well-being. Taking coal mining and consumption as an example, coal has been widely used to generate electricity since the 1880s, and more than 40% of the electricity globally is provided by coal nowadays. However, as one of the largest worldwide anthropogenic sources of carbon dioxide releases (39% of global CO2 emissions), the extensive excavation and utilization of coal have brought a series of side effects to both natural environment and human health (Wikipedia 2017). As the largest coal producer and consumer in the world, China is leading the list over the past decade (as shown in Figure 1) (BP 2016). The excavation and utilization of coal resources have made a crucial impact and irreplaceable contributions to China’s industrial development and economic prosperity (Long and Zhang 2009). However, most of the air pollution in China are also attributed to the simplified and extensive exploitation of coal resources, e.g., 90% of SO2, 67% of NO, 70% of smoke ashes, and 70% of CO2 in 2016. In recent years, most of North China and the developed coastal areas were wreathed by smog due largely to the oversimplified extensive utilization of coal, suggesting that the development patterns of coal utilization need to be reshaped so that both the biosphere and humanity could thrive equally."

Jan 1, 2017

By Cyrus W. Field

The Pacific Northwest as defined in this review comprises an exceedingly large and geologically complex terrain that occupies the 'Western Cordillera mobile tectonic belt. This metallogenic province is approximately 2100 miles long and 350 to 500 miles wide. It extends north-northwest from northern California and Nevada, through western Idaho and Montana, Oregon, Washington, British Columbia, and southwestern Yukon Territory, to southern Alaska, and west from the western flank of the Northern Rocky Mountains to the continental margin (Fig. 1). Many detailed and thorough exploration programs that have been conducted by mining and petroleum companies for over a decade have demonstrated that porphyry-type deposits are both numerous and wide-spread throughout this province. Although the Granby Mining Company extracted about 34 million tons of copper sulfide ore from Copper Mountain during the period 1900-1957, intentional large-scale production of porphyry-type ores was first initiated in 1962. It began at Bethlehem Copper Corporation's East Jersey orebody in the Highland Valley District of south-central British Columbia, approximately eight years after Mr. H. H. Huestis rediscovered that broad zone of copper-molybdenum metallization and recognized its potential significance.

Jan 1, 1973

By Annan Cook

J.R. Atkinson, office engineer to Kennecott Copper Corp., summarized data on the Mineral Park area [Wallapai (Chloride) Mining District, Mohave County, Arizona, Fig. 1] and submitted it to the New York office in 1950. He recommended an examination. Weston Bourret, a Kennecott geologist, accompanied by B.S. Butler, the well known former US Geological Survey geologist, examined the larger of two hydrothermally altered areas in Mineral Park that same year. Bourret recommended that the property be optioned and mapped. Georges Ordonez, Kennecott's chief geologist, after a field examination, agreed with Bourret's conclusions At the end of the summer of 1951, Annan Cook (another Kennecott geologist) accompanied Ordonez to the property prior to starting a mapping program. At Ithaca Peak, the structure, alteration, and reddish-brown coloring in leached cavities-hematite, jarosite, and goethite with minor copper staining - made an interesting target. The Peak, which has since been mined, was a Laramide quartz monzonite porphyry grading into quartz porphyry, penetrating Precambrian rocks. Turquoise had been mined from several workings on the Peak. Surrounding the central area of alteration, but mainly to the northwest, there were many long-abandoned underground workings mined for zinc, lead, gold, silver, and copper. To the west of Ithaca Peak within the main area of alteration, surface evidence of a chum drill hole suggested interest in the disseminated mineralization probably prior to World War II. A topographic and geologic survey of the altered Ithaca Peak area was initiated by Cook in September 1951. He was assisted by Richard Vosburgh, field engineer, and by four geologists: Charles Goddard, III, Donlon LoBionda, Keith Martin, and A.T. Stone. When Cook returned to New York, Vosburgh was left in charge. Mapping continued and diamond drilling took place during the winter of 1951-1952. Drill sites were selected entirely on the basis of surface geology. Five drill holes, including a flat hole, located around the flanks of Ithaca Peak, averaged about 183 m (600 ft) in length. A sixth hole caved at less than 60 m (200 ft). The best values obtained were in the first hole (-45°): 90 m (300 ft) averaged 0.62% copper and 103 m (337 ft) averaged 0.041% molybdenum. In another hole, 43 m (142 ft) averaged 1.09% copper and 0:023% molybdenum. The values of copper and molybdenum in these two holes were generally higher than in the remaining holes, although molybdenum values were always around 0.024% or better. The New York office decided, however, to abandon the project even though the remaining field crew of three had recommended more drilling.

Jan 1, 1991

By Rod A. Levander, Kenneth B. King

INTRODUCTION The Panna Maria Uranium Project is located in South Texas, between San Antonio and Corpus Cristi, approximately 10 kilometers (6 miles) north of Karnes City, Texas. The tailings disposal facilities are located immediately south of the mill area and the central portion of the west pit. The mine and mill drainage pond is located north of the tailings pond. Location of the facilities is shown in Figure 1. The tailings pond is a disposal area for mill process wastes and has a capacity for storage of approximately 9 million metric tons (10 million tons) of tailings. This capacity is adequate for approximately 10 years of milling at a maximum rate of 2,700 metric tons (3,000 tons) per day. The tailings disposal facilities were designed to essentially eliminate discharge of contaminated waters to preclude degradation of surface streams or ground water. Water levels in the ponds will be maintained. through reuse in the mill and by evaporation. WASTE CHARACTERISTICS The sources of waste that is stored in the tailings pond include runoff from the mill area and tailings from the mill processing. The tailings consist of a sand slime slurry; the percentage passing the No. 200 sieve varies depending on the ore material, and it is generally in the range of 10 to 25 percent. The tailings have a density of approximately 1.2 metric tons per cu m (75 lb per cu ft) and an average specific gravity of 2.55. The liquid effluent from the mill consists of waste solutions from the grinding, leaching, extraction, and washing circuits of the mill. These solutions have an initial pH of 1.5 to 2.0 and contain the remnants of the leaching agents used in the mill process, sulfates, some silica as the primary dissolved solid, and trace quantities of soluble metals. This liquid is discharged with the solids into the tailings pond and is diluted by rainfall and runoff from the tailings dam. Runoff from the mill area, drainage from the mine area, and de-oiled water from truck washing facilities is discharged into the mine and mill drainage pond. Runoff from the mill area drains approximately 28 hectares (70 acres) from offices, shops, the mill site, the ore pad, haul roads, and adjacent areas. Mine drainage is collected in the mine area and pumped to the mine and mill drainage pond.

Jan 1, 1980

By P. J. Hyde

Cyanide is a significant contributor to the cost of producing gold. Any reduction in consumption that can be achieved through more reliable measurement and/or more efficient management of dosing rates can have a significant financial impact. An automated analyser, by its mechanical nature, is not prone to the variations of human operators, particularly notice­able from shift to shift. Reducing the standard deviation of the measurement (ie, reducing noise ), the automated measurement will give the metallurgist a truer picture of the underlying patterns of usage. The combination of automated analysis with on-line operation and a control loop provides timely information that is efficiently utilised in the management of the plant. Until the release of the Chemtronics On-Line Cyanide Analyser (OTA3000) about 12 months ago, the Australian experience with automated analysers (especially on-line) had been substantially negative. Since its release, the Chemtronics instrument has outperformed both manual titrations and other automated instruments, gaining an enviable reputation for accuracy and reliability in the process. The instrument is built around the technique ofpotentiomet­ric titrations, in which the potential of an indicator electrode is measured as a function of the volume oftitrant that is added to the sample. As the cyanide in the sample is depleted, the potential on the indicator electrode changes rapidly, producing a typical sigmoidal curve. The OTA3000 takes the first differ­ential of the curve, identifies the apex of the peak as the endpoint and reports the result in parts per million of sodium cyanide. The OTA3000 accepts the peak as valid only if it exceeds a certain minimum height. That minimum height is a programma­ble parameter and is used to optimise the relationship between sensitivity and the rejection of spurious peaks. The instrument will track cyanide trends through both positive and negative slopes of any magnitude, but it will provide a warning if it the slope becomes excessive, not because it affects the instrument but because it means that something unusual is occurring in the tanks. There are a limited number of conditions under which the instrument will produce a result of zero. In these cases the OTA3000 holds any output lines at the last valid result while it repeats the titration. This feature was incorporated for reasons of stability in a feedback loop.

Jan 1, 1995

By Anibal Gajardo

Clays for building bricks and roofing tiles in Chile are classified as common clays and ball clays, with deposits of sedimentary and residual origin, both Cenozoic in age. Deposits are known from north to south, through 11 of the 13 Chilean Administrative Regions, 18° to 39° South latitude, and from west to east, through three of Chile's main geomorphic features, namely the Coastal Plains, Coastal Range, and Intermediate Depression. Alluvial and lacustrine sedimentary common clay deposits are located in the northern and southern Intermediate Depression. The average chemical composition of clay deposits in I and I1 Regions, is 58 percent Si02, 16 percent A1203, and 4 percent Fe203 by weight; the primary minerals are sericite, quartz, feldspar, and albite. The average chemical composition of clays in Metropolitan, VI, and VIII Regions, is 52 percent Si02, 16 percent A1203, and 6 percent Fe203 by weight; the primary minerals are montmorillonite, quartz, and plagioclase. Residual common clay deposits occur in the Intermediate Depression and in the Coastal Range internal basins, VII, VLII, and IX Regions, and they represent surficial alteration of pumice beds and crystalline rocks. The average chemical composition of clay deposits derived from crystalline rocks is 58 percent SO2, 17 percent A1203, and 9 percent Fe203 by weight; the primary minerals are sericite, quartz, and clinochlore. Clay deposits formed from pumice beds contain 47 percent Si02, 24 percent A1203, and 10 percent Fe203 by weight; the primary minerals are kaolinite, feldspar, and cristobalite. Sedimentary ball clay deposits are located in the Coastal Plains and Coastal Range, VI, VII, VIII, and IX Regions, between 34" and 39" South latitude. The average chemical composition of the ball clay deposits is 51 percent ,902, 28 percent A1203, 5 percent Fe203 by weight; the primary minerals are kaolinite, quartz, and sericite (illite?). These clay deposits supply the Chilean building sector with over one million metric tons (mt) (1.1 million short tons [st]) of material per year. The average growth rate of clay consumption during the period 1993 through 1997 was 10 percent annually. The clays are used by both mechanized plants and handcraft facilities.

Jan 1, 2001

By Geoffrey Purcell

The flotation response to amine collector of quartz and the feldspars microcline and albite, of the pyroxenes augite and spodumene, and of olivine can be, explained by a physical adsorption model. Flotation decreases in the order given above, and the different behavior of the three groups is attributed to structural variations of the silicates, With sulfonate collector both chemical action and physical adsorption play their part in producing hydrophobic surfaces, and flotation increases in the order given.

Jan 1, 1966

By V. E. May

Has your organization adopted Six Sigma as part of their Performance Improvement strategy? What about Lean manufacturing or Lean Six Sigma? If you already have any of these business process improvements in place where will you go next? In this article we will focus on transforming your organization beyond Lean Six Sigma to the next level of performance. In the future companies can take another quantum step forward by combining Lean Six Sigma with advanced Root Cause Analysis (RCA). The value of taking this natural progression on the way to achieving new levels of organizational excellence is presented.

Jan 1, 2011

By Hugh E. Cronin, Joseph J. Coluccio

The Columbia Slough Consolidation Conduit Project is a 12 ft. 0 in. inside diameter—15 ft. 4 in. excavated diameter tunnel, 8,300 lf. in length. The tunnel is divided in two parts a 4,460 lf. reach to the West and a 3,770 lf. reach to the East separated by a flow regulation structure in the middle. The project was built for the City of Portland, Oregon Bureau of Environmental Services (BES) by the Frank Coluccio Construction Company (FCCC) Seattle, Washington under a $22,600,000.00 contract starting in 1998 and completing the contract in 2000 at a total cost to the City of $25,448,000. An increase of 12.6% from the original contract. The tunnel was constructed in an alluvial sediment that ranges up to 1,500 feet thick. The sediment varies from ?ne silty sand and sandy silt (SM-ML) to coarse sand and gravel (GP-GM) with varying quantities of cobbles and boulders. Most of the tunnel was constructed above the water table although one reach of almost 1,000 lf. had water to above the tunnel crown. The contractor, FCCC, used a Lovat 15 ft. 3 in.900 hp shielded TBM with multiple doors (4) of variable opening to excavate and support the tunnel. Tunnel supports were 5 in. WF 16 lbs. per foot at 4 ft. spacing and4 in. Douglas Fir lagging. Tunnel excavation was worked in 10 hour shifts with additional equipment maintenance and repair on the off time. The original Geotechnical Design Summary Report (GDSR) established a baseline for contractual purposes of slightly over 5 boulders (between 12 in. and48 in.) per foot of tunnel. (Table 1) At the pre-bid conference, three test pits were excavated to approximately tunnel invert, one at each end of the project and one in the middle near the flow regulation structure. The test pits encountered a few boulders but did not seem to support the five boulders per foot (varied from one boulder per foot of tunnel to eight b/lf.). Subsequent to the pre-bid meeting and the test pits, BES issued any addenda which changed the baseline boulder quantity in the GDSR to 1.7 boulders per foot of tunnel (varied from0.2 to 3.5 boulders per foot) a reduction of 67% from the original baseline. It is interesting to note the two separate tunnel reaches and how they were evaluated in the GDSR. Originally the Eastern portion of the work was projected at5.08 boulders per foot of tunnel and the Western portion at 5.30 boulders per foot of tunnel for a variance of less than 5%. In the revised quantity the Eastern portion was projected at 2.01 boulders per foot of tunnel and the Western portion at 1.42 boulders

Jan 1, 2003

By John T. McDonough

The Climax Mine of AMAX's Climax Molybdenum Division is currently producing approximately 34,000 tons of molybdenum ore per day from two underground levels (see Figure I), and initial design is underway for the next deeper (1200) level. The aim of this report is to present the methods of site evaluation used at Climax for cavability determinations and underground support design. Climax succeeds with its panel caving system of mining (Julin, 1973) (Figure 2) largely because of the presence of pervasive geologic structural discontinuities. The stockwork ore body at Climax was formed by the multiple intrusion of mid-Tertiary rhyolitic magmas into Precambrian granite, schist and gneiss, and the hydrothermal emplacement of molybdenite into the network of fractures that were generated during the forceful upward intrusion of magma. Subsequently, intrusive events that were more deeply seated refractured the overlying, ore- bearing stock and propagated a complex system of axial and radial fractures. Post-ore movement along the Mosquito Fault (Wallace, 1968) and its associated stranded shear zones further fractured the ore body and disordered the existent geologic structure. The result of these structural events is a brittle, crystalline ore body that is transected by a complex pattern of faults, shear zones, and joints that augment cave initiation and enhance comminution of the ore blocks. Generalizations can be made about the structural trends within the ore deposit (King, 1946; Kendorski, 1973), however, the intensity and orientation of geologic structure is by no means uniform throughout the ore body. The relative intensities of silicic and argillic alteration are also highly variable (Vanderwilt and King, 1955). As a consequence, no single rock-mass model suffices as a standard for mine design, and site characterization for cavability and support design is a continuous process.

Jan 1, 1977

By James H. Harmon

As the trend to deeper mines, producing from marginal ore bodies, continues, mine hoists and their associated equipment will become more sophisticated, complex, large and expensive. Over the past two decades, mine hoisting equipment and systems have moved from steam engines to static rectification of ac to dc, and electronic controls are the standard. It is the intent of this section to present what is currently available in the field of mine hoisting equipment and systems. Because the present engineer has been exposed longer and more intensively to such things as computers, electronic devices, and machine design, no attempt has been made to make this a layman's article. Contributions from the electrical design and application engineer, gearing and hearing design engineers and other specialists have been incorporated. Some material will be devoted to electrical drive systems, rectifiers and gearing design among others. These items are inherent in the design of a mine hoisting system and the subsequent selection of the correct, most reliable and most economic system. The mine hoist can be a bottleneck between the underground mine and the surface mill. Correct selection of the right type of hoist is imperative. In this vital link between mine and mill, crude estimates of hoist capacity are not good enough, and the mining engineer must design and select the right hoisting system to meet the design specifications. 15.1-MINE HOIST TYPES There are two basic types of mine hoists available anywhere in the world today: the drum hoist on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe), which merely passes the rope over the wheel during the hoisting process. Drum and friction hoists are "generic" terms which describe the two basic categories. Within each category are variations, as below. 15.1.1-DRUM HOISTS Drum hoists, as noted, actually store the hoist rope on the drum much the same as line on a fishing reel. To accomplish this task, the drums are so designed to store, in one or more layers, the footage of wire rope equal to the total maximum hoisting distance plus sufficient rope for cutting and inspection at regular intervals and for holding to the drum (see Fig. 15-1). Usual practice in hoist drum design is to allow three turns of hoist rope for holding on the drum and three turns for inspection cuttings. 1. Single-Drum Hoists-Fig. 15-2 shows a typical single-drum hoist as manufactured by most U.S. heavy-mining-equipment companies. With the exception of some very minor features, this design configuration is standard throughout the U.S.A. Fig. 15-3 is a plan view of a typical single-drum mine hoist. This particular hoist has a single-motor drive and a double-reduction set of gearing.

Jan 1, 1973

By David Williamson

In the post-World War II years, metals analysts and statisticians have tracked the demand for metals in line with changes in Organization of Economic Cooperation and Development (OECD) industrial production (IP) growth rates, Williamson said. This was because the correlation between IP growth and metal demand was reasonable. "However, the correlation was exaggerated," he said. During times of expanding IP growth, metal demand increased at a faster proportional rate than IP growth. This was probably due to industry restocking in anticipation of growing demand at the start of each economic cycle. Conversely, metal demand would slacken at a greater rate than would be suggested by negative IP growth as industry destocked to reduce costs. Nonetheless, he said, a reasonable correlation could be painted between IP growth over the longer term and metal demand. "Yet, although this correlation has stood well since the last world war, it has been based on the fact that the bulk of the world's IP growth stemmed from the industrialized countries of the western world, lately including Japan," Williamson said. The so-called "developing world" had been of little consequence. The Soviet Union and other communist bloc countries were deemed to be closed, self-contained entities that, for each metal, would either be net exporters or importers, he said. These quantities would be used by analysts to calculate the overall supply/demand equation for the western world only and to deduce whether a commodity was in shortage or surplus. It is now believed that this method of projecting total world supply and demand for raw materials is outdated, Williamson said. It does not take into account the worldwide political changes that have occurred since the collapse of communism and the revitalization of China. "It is no longer appropriate to assess global balances for raw materials on the basis of three economic blocs," he said, including the western world, developing world and communist bloc. Rather, global balances need to be projected on a global basis. In this regard, since the collapse of communism and the removal of many other totalitarian regimes, capitalist forces are attempting to satisfy the expectations of the great mass of the world's poorer people, Williamson said. Such people, usually located in Asia, Africa and Latin America, have aspired to the same standard of living as people living in western Europe, North America and Japan. "Now, with free market forces at work, their aspirations will start to be met." Consequently, the demand for metals and other raw materials will now rise at a much faster rate. The production of raw materials has to keep pace with rising IP in the developed world. It will also have to keep pace with the demands associated with the rising expectations of increasing populations in the developing world, as well as from within the old communist bloc countries.

Jan 1, 1997

By Roman Z. Pyrih

Subsurface migration of cyanide is attenuated by naturally occurring geochemical and biogeochemical processes. Geochemical mechanisms which remove or immobilize cyanide and metal-cyanide complexes include precipitation/coprecipitation, sorption, and volatilization. Geochemical properties of soils and geochemical materials that promote the functioning of these mechanisms include the following: 1) acidic soil pH; 2) presence of illite and smectite clays; and 3) presence of iron hydrous-oxides and organic carbon. Naturally occurring soil microorganisms play perhaps a more important role in attenuating cyanide movement than previously realized. Biodegradation of cyanide is a "renewable" process, limited in its effectiveness by the avalibility of oxygen and micronutrlents (usually phosphate) to the microorganisms.

Jan 1, 1990

By R. O. Burt

The Tanco pegmatite is located in the Bird River greenstone belt of south-eastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). The orebody was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANCO), and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco's currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Corporation, and the Province of Manitoba.

Jan 1, 1988

By K. Rajamani

A mathematical model based on the pertinent fluid dynamic equations to predict the performance of the hydro cyclone has been developed which will eventually replace the empirical model. Experimental measurements of fluid velocity profiles made in a 75 mm hydrocyclone by laser Doppler velocimetry (LDV) agree well their predictions by solving the Navier-Stokes equations numerically. Particle slip velocity and particle trajectory were computed which in turn, yields separation curve of the hydrocyclone.

Jan 1, 1988

By J. E. Osmanski

This semantically ambiguous title purports to describe an examination of the question of automation and its effect on the industrial worker. More explicit titles might be "Painless Automation" or "Mechanization without a Sting" or, if I may steal a few phrases from the title of a recent interview Pith John L. Lewis, "More Machines, Fewer Men -- Is the Union Happy About It?" Automation has become the biggest ?scare word? for many industrial workers and their unions since "wage stabilization.? "To many a union orator," reports TIME of January 4, "automation is the sinister business of eliminating jobs." TIME might better have phrased this description by saying that many unions regard automation as the attempt to eliminate not jobs, but workers, The recent steel dispute was hung up for so long primarily because of the problems evolved of increased job efficiency through automation and job changes. Everywhere today there is heard the cry of our need for maintaining full employment within the context of an expanding economy echoing against the sheer reality of automation's displacement of thousands of workers through a rapid acceleration of productivity.

Jan 1, 1960

By Claude A. Chapallaz, Dominique L. Butty

Bauxite is derived by surficial weathering of aluminosilicate rock forming minerals under warm and humid climatic conditions. Variations in climate combined with base level changes promote cyclical, evolutionary weathering/concentration patterns, the residual products of which are closely controlled by biological activity. Rock decomposition results mainly from hydrolysis, chelation and solution, the effects being (a) removal of bases and silica in dilute solution, (b) depletion of iron in areas where low pH-Eh prevail and, (c) concentration through direct precipitation, or more generally via intermediate amorphous phases, of aluminium hydrates in variable associations with iron hydrates and clay minerals. Bauxites can be regarded as aluminous soils, and as such they result from cyclic or polygenetic pedogenesis. The ferralitic pedological evolution is essential for bauxite formation. Under some specific conditions, related to local climate and parent rock composition, the podsolic- or andosolic-type of pedogenesis is an effective precursor to bauxitization.

Jan 1, 1984

By John T. Crawford

Various open pit limit-analysis techniques have been utilized for many years to design pit limit surfaces. In the last 15 years there have been many advances in developing sophisticated computer methods to aid this process. The extensive capability of the digital computer has led to effective utilization of multiple alternative approaches to problem solving. Computerized open pit limit analysis methods can be applied to a broad scope of long range and intermediate range mine planning and design needs. This paper provides an overview of some of the more important of these applications. While not covered in detail, they are meant to indicate the flexibility and adaptability of open pit limit analysis methods and to stimulate thought.

Jan 1, 1979

By R. V. Ramani

Control is a vital management function by which operations are brought into compliance with predetermined standards to achieve the goals of an enterprise. Events that are characterized by a low degree of expectation, avoidability, and intent necessarily have a low degree of control. Such events are difficult not only to predict but to control as well. Fortunately, very few industrial situations fall into that category of events. It is an axiom of control technology that in order to control, one must first measure; further to measure, one must know the characteristics of the subject (or environment) upon which the measurement must be made. Finally, if measurements are to be made reliably, the influences that affect the measurement must be known and, if possible, understood. The complete control cycle therefore consists of the following: (1) defining the objective, (2) planning to achieve the objective, (3) putting the plan into practice with appropriate instructions, (4) measuring variables or parameters of interest, (5) transmitting and transforming the measurements to analyze the system's status and to predict the future outcome, (6) comparing these with the defined objective, and (7) determining and taking corrective actions to bring the actual results closer to the objective. The management principle underlying the control cycle is the principle of management by exception. The application of the principle and the frequency with which corrective actions are taken vary according to the purposes of the review and control. For example, the control of a machine operation (e.g., truck on a haul road) may require adjustments and therefore data, analysis, and decisions, in intervals of seconds whereas the review for ore-grade control may take several hours. Reviews, on the other hand, for cost control may be done in intervals of weeks or months. In any case, three specific purposes of the control cycle are: (1) to correct the operation so that it follows the accepted plan closely, (2) to evaluate the operation and predict future outcomes in light of changes in the environment or of more experience, and (3) to review the objectives and modify these to be reasonable and realistic.

Jan 1, 1979