Search Documents

An information system (I/S) plan is a means for establishing and communicating the direction the organization intends to take to provide the information required for achievement of organizational goals and objectives. The rapid advancements in information technology, the increasing complexity of systems, and the growing dependence of mining companies on these information systems have emphasized the need for more comprehensive I/S planning. This subsection explores this need, the role I/S planning can play within a mining company, and finally describes a methodology for development of an I/S plan.

Jan 1, 1979

By Graham G. W. Mustoe, Andrew I. Hustrulid

An advanced numerical model based upon the Discrete Element Method (DEM) has been developed to provide the engineer with unique detailed information to assist in the design of transfer points in large industrial conveyor systems in mining operations. This modeling technique provides a quantitative description of the bulk solids movement through the transfer point. This information consists of the velocity distribution of the bulk solids and the stresses within the bulk solids. The DEM model also gives detailed information concerning the impact forces acting on the transfer structure and the conveyor belts from the bulk solids flow.

Jan 1, 1996

By I. González, G. Lapidus, M. Teutli

The cementation kinetics of silver with aluminum particles were studied with model solutions under nitrogen atmosphere, varying the temperature, aluminum/silver ratio, pH and concentrations of thiourea and surface activator Recoveries were evaluated both by solution concentrations and by REDOX measurements. Tafel curves were determined for this system. The results showed the cementation process to be essentially independent of the pH and thiourea concentration. However, a strong influence was observed with respect to temperature, aluminum/silver ratio and the quantity of activator. There is evidence that the controlling step is the dissolution of aluminum oxide from the particle surface.

Jan 1, 1990

Simulation models were developed at the Julius kruttschnitt Mineral Research Centre to provide accurate estimates of power consumption for a wide range of equipment. With the models, a range of circuits and operating conditions can be compared by simulation for a particular ore type. Accurate models of classification allow for the interaction between classifier efficiency and target product size (e.g., P80 or percent passing 150 /an) to be considered. This paper considers a range of circuit types and overall energy efficiency in the context of case studies where different circuit types were treating similar ore types.

Jan 1, 1999

By Randy J. Mikula

Cleaning of low-rank coals can have several meanings, depending upon the definitions of the terms "low rank" and "cleaning." In general, low-rank coals would be lignite or subbituminous according to the ASTM classification. For the purposes of this summary, cleaning is defined to be any process which materially reduces the proportion of inert material in the coal. For low-rank coals, this often means a reduction in moisture content since moisture is the major inert component in these coals. A brief discussion of conventional cleaning processes is included, as is an extensive reference list.

Jan 1, 1991

By M. Z. Rashad, H. A. El-Sageer

The intersections of numerous joint sets at the surface of tunnels of the Abu-Tartour project in Egypt create blocks of irregular shape and size in the rock mass. Although most of these blocks are unable to move into the free space of the tunnel, a few key blocks are capable of such movement. In addition, as soon as they move, some restrained blocks will be liberated. The aim of this work is to find the removable key blocks of the walls, floor, roof and corners of a portion of the tunnel under jointed surface rocks and then determine the best tunnel direction.

Jan 1, 1993

By Violetta Pavlova

Knowledge of geometrical properties of blocks in a hard jointed rock among other things is of considerable importance for prediction of rock mass behavior and for its exploitation. This paper presents a new approach to obtain the information about percentage of blocks with desirable geometrical properties in a jointed rock mass extending through a large region of interest. A model of a rock mass separated by finite number of systems of parallel plane discontinuities which form discrete blocks is discussed. A computational procedure has been derived to analyze the volume and shape distribution of blocks in the rock mass.

Jan 1, 1992

By K. F. Unrug

Martin County Coal Corp. is located in Martin County, KY, in the Appalachian coal fields, near the West Virginia border. The company's total leasehold covers more then 133.5 km' (33,000 acres). Total annual production at Martin County Coal Corp. is currently 2.2 Mt (2.5 million st). In certain years, though, it exceeded 2.7 Mt (3 million st). About 45% of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal's work schedule consists of two nine-hour shifts a day, 240 days a year. Topography The topography of the area is characterized by rugged hills and ridges and sharp V-shaped valleys demonstrating a cliff and slope topography. This topography consists of alternating benches of outcrop sandstone and slopes. The deep valleys have been carved out by many small streams in the area. These streams are contained within the steep slopes of narrow, twisted mountain ridges. The ridges are underlain by massive sandstones that, being resistant to erosion, create sharp, rocky morphology. The height of the hills above the valley floors ranges from 122 to 244 m (400 to 800 ft).

Jan 1, 1991

By P. Somasundaran, H. S. Hanna

The separation of minerals such as apatite and scheelite by flotation from other salt-type minerals such as calcite is extremely complex owing to the close similarity between their physicochemical properties. In this paper, properties relevant to flotation such as crystal structure, solubility, surface charge and adsorption behavior of important salt-type minerals are examined along with the role of inorganic modifying agents such as silicates and polyphosphates and organic modifying agents such as starch and tannin. Flotation characteristics of these minerals are then reviewed and selected separation problems involving salt-type minerals are discussed.

Jan 1, 1976

Current design guidelines for the surface catalysed oxidation of Fe(II) on Fe(OH)3 (Ochre) in passive mine water treatment systems are based largely on empirical data as the details of rates and mechanisms have not fully been revealed. Also the effects of elevated carbonate concentrations, typical of many UK minewaters, on the surface catalysed oxidation rate are unclear. In order to move away from empirical design and towards sound engineering that is based on geochemical and hydrological understanding it is necessary to quantify these reaction rates. In this study the effects of Fe(OH)3 and carbonate on the rate of Fe(II) oxidation by dissolved oxygen have been investigated with an aim to delineate the reaction mechanism. Experiments were conducted under well-controlled conditions. Preliminary results indicate that the surface catalysed reaction is an order of magnitude faster at pH ~6.4 with 200 mg/l Fe(OH)3 than the homogeneous rate and is dominated by an elevated rate of removal and oxidation of Fe(II) from the solution phase. It is also apparent that the oxidation rate of actual adsorbed Fe(II) is substantially retarded with respect to the homogeneous rate. Carbonates were not shown to affect the surface rate within the bounds of this preliminary study.

Jan 1, 2006

By Jacques Villeneuve, Stéphane Brochot, Jean-Claude Guillaneau, Marie-Véronique Durance

Since 1986, BRGM has been developing a powerful process simulation software package, USIM PAC. These last years have seen significant developments in mineral processing technologies, particularly in hydrometallurgy, bio-hydrometallurgy and mineral liberation. The new version of the simulator, USIM PAC 3.0, incorporates these modem-processing fields. Its structure and tools allow the user to take into account, at the same time, a wide range of technological, economical and environmental aspects. The improvement of the existing features and the introduction of new unit operation mathematical models and tools such as the supervisor, global optimization, workshop model or chemical reactions contribute to a global approach in mineral processing design.

Jan 1, 2002

By Val Cachic, Harry M. Castrantas, Craig McKenzie

In April 1986, FMC- Paradise Peak Corporation began milling at the Paradise Peak Mine, which is located eight miles southeast of Gabbs, Nevada. The mill processes about 4DOO tons per day of ore through the mill and cyanide leaching circuit. Gold and silver are recovered via the Merrill-Crowe zinc precipitation process. Tailings are routed to a tailings pond located about one half mile southeast of the mill facility. The pond, lined with 60 mil MDPE, was 25 acres at the start of the cyanide detoxification, covers 90 acres and will ultimately cover 180 acres. Solution is reclaimed from the pond and circulated back to the mill.

Jan 1, 1998

By C. H. Bucknam, A. M. Raichur, M. Misra

Simultaneous dissolution of mercury along with gold occurs during cyanidation of gold ores. A method has been found for the efficient removal of mercury from the gold cyanide solution by treating with dithiocarbamates which form stable compounds with mercury. The mercury concentration in the leach solution can be brought down to low levels by adopting this treatment. Furthermore, it is also possible to stabilize the mercury in the ore heap itself by addition of this reagent so that mercury does not dissolve in the cyanide solution during heap leaching. Only trace amounts of mercury were detected in the pregnant solution obtained from a heap treated with dithiocarbamates. In this paper, process parameters are discussed in detail.

Jan 1, 1997

By Y. M. Jiang, R. L. Sanford, D. W. Park

Artificial intelligence has emerged over the past two decades as an important problem-solving tool. Techniques include expert systems, neural networks, free classification, fuzzy logic and genetic algorithm. These methods can be employed to solve rock mechanics and ground-control problems associated with the highly complex nature of rock masses and ground conditions. A current study focuses on the development of an artificial-intelligence system for real-time interpretation of data collected from longwall monitoring stations and on the development of an early warning system for the prediction of undesired conditions and the prevention of longwall-mine instability problems. The successful application of these artificial-intelligence techniques will contribute to a safer and healthier mining environment.

Jan 1, 1997

By W. Allen Dupree, Charles D. Campbell

A field investigation was conducted by the Ventilation Division, Pittsburgh Health Technology Center (PHTC), Mine Safety and Health Administration (MSHA) to evaluate the effectiveness of a blowing face ventilation system utilizing a water sprayfan system and a single inlet flooded bed dust collector (scrubber) in controlling methane liberation in the face area while mining at brattice distances up to 12.2 meters (40 feet) from the face. The rated capacity of the scrubber was 117 m3/s (4,145 cfm) of air. Results from the investigation indicated a methane dilution capacity of 0.57 m3/s (20 cfm) with the air quantity behind the line brattice averaging 138.7 m3/s (4,900 cfm).

Jan 1, 1991

Gold heap leach operations often process low grade ores with little margin for cost increases. The advantage of heap leach operations is the considerable savings in both capital and operating costs. This paper looks at an alternative pH modifier to lime in the heap leach process, namely bauxite waste mud or red mud. The red mud can contain trace amounts of gold and was found to be an excellent source of slow release sodium hydroxide for long-term pH modification. Column cyanide leaches showed that 25 kgt-1 of red mud provided a higher pH and longer pH modification than 0.25 kgt-1 of lime. Contaminants leached from the red mud hampered the adsorption of the aurocyanide complex onto activated carbon.

Jan 1, 1993

By Victor F. Hollister

The great increase in post-World War I1 use of molybdenum was made possible by discoveries of that metal in porphyry molybdenum and porphyry copper deposits. This section documents significant porphyry molybdenum discoveries of the post-war period. The most important discovery was Henderson in Colorado. It is not only one of the world's largest and richest, but it was found by a team of geologists who defined the hood model and tested it successfully at Henderson. Under the leadership of Stewart Wallace, these scientists established a set of criteria for exploration for Henderson-type de- posits that was copied by the industry. The discovery bf vertical cylinder type porphyry molybdenum deposits was less renowned. Boss Mountain in British Columbia and then Mt. Pleasant in New Brunswick were given relatively scant notice, compared with the Henderson discovery. However, these deposits have geometrics distinct from that found in the typical hood, which directly affects their exploration characteristics. Mt. Pleasant, included in this section, is a well defined, near vertical breccia pipe. Both the Henderson and Mt. Pleasant discoveries were made by relatively small groups operating independently of the bureaucracy that characterizes large corporations. The management role in each case was one of encouragement. In addition, Wallace had the beneficial experience of working for Climax, whose objective was the discovery of porphyry molybdenum deposits. Henderson was the natural outgrowth of the exploration effort by those who studied and understood the Climax deposit.

Jan 1, 1991

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By P. Ollivier

A comparative study on potential refractory ore processing techniques was launched at the BRGM to enable exploitation of numerous small deposits of arsenopyrite and antimony sulphide ores.

Jan 1, 1998