Search Documents

By John C. Gould

GENERAL DESCRIPTION The Climax mine is located 161 km (100 miles) southwest of Denver on Fremont Pass astride the Con¬tinental Divide. Climax employs 2800 people to pro¬duce 42 670 t/d (47,000 stpd) of molybdenum ore. The Storke level, the main underground level, produces 19 970 t/d (22,000 stpd); the 600 level, the lowest ac¬tive underground area, produces 7260 t/d (8000 stpd); and the open pit presently produces 15 430 t/d (17,000 stpd), Fig. 1. A panel caving method is possible because of the favorable geology and geometry of the Climax ore body. Geology The Climax deposit is composed of three separate ore bodies formed in a massive Tertiary stockwork which penetrates Precambrian granites and schists. The ore bodies are elliptical in plan with overall dimensions of 914 x 1219 m (3000 x 4000 ft). In section the ore bodies are arcuate with an overall height of 457 m (1500 ft), although the depth is not firmly ascertained. Ore grade decreases rapidly into a highly siliceous cen¬tral core and more gradually toward the outer bounda¬ries of the deposit. The mineralization is relatively continuous in the ore zone and contains few dilution-causing waste inclusions. Molybdenite is contained in pre-ore fractures which were largely recemented during the three mineralization pulses. Postore fractures, with a spacing of a few inches to several meters (feet), render the deposit amenable to caving when it is undercut. The peripheral rock caves similarly to the ore, but the central core is competent and is difficult to cave. Caving Feasibility Successful caving action requires an undercut area of approximately 122 by 122 m (400 by 400 ft). When the undercut area exceeds this minimum distance, the arching effect is lost, and the ore column collapses. Ore extensions from the main cave area less than 122 m (400 ft) wide usually cannot be caved. Waste or low¬grade areas within the deposit can be left if they are large enough to carry weight around openings passing through them. Experience indicates that these areas should be over 30 m (100 ft) in length and width. Smaller unprofitable units of waste, such as postore dikes, are mined to avoid weight problems and result in ore dilution. Successful caving and ore recovery are dependent upon timely ore removal from the undercut zone because columns of immobile ore inhibit caving and concentrate weight onto the underlying workings. Climax experience indicates that a finger (drawpoint) spacing* averaging 10.4 m (34 ft) yields an excellent caving action and a 92.5% ore recovery at the estimated grade. An additional 15% of the ore is recovered-at a diluted grade (Fig. 2). Mine Layout The slusher drift is the primary production facility (Fig. 3). The ore is undercut and caved into the fingers,

Jan 1, 1982

By Mark L. Mott, Michael P. Synder

The Mine Safety and Health Administration has developed a program to improve the decision making process of personnel involved in mine emergency situations. The Mine Emergency Responsiveness Development Program (MERD) has been designed specifically for fires and explosions in underground mines. This program addresses the responsibilities and organizational requirements that are necessary during rescue and recovery operations of a mine emergency . Specific skills and knowledge are required to manage an organization of personnel under conditions of intense stress, such as a mine fire or explosion. As a result, the MERD program develops these skills by providing role playing emergency simulations. This role playing provides the participants with the opportunity to experience problems, explore solutions and interact with other personalities which may exist during mine emergency situations. This paper presents the standard procedures for the MERD program developed by the Ventilation Division of the Pittsburgh Health Technology Center.

Jan 1, 1991

By John Pekrul

Coeur Rochester Inc. located in north central Nevada, operates an open pit mine moving a total of 16 - 18 million short tons of material per year. A three stage crusher produces approximately 8 million tons of a minus half inch product that utilizes truck stacking to construct a heap leach with a zinc precipitation recov­ery plant. Coeur Rochester recovers approximately 6.0 - 7.0 MM ounces of silver and 60 - 80 K ounces of gold annually. Current metal prices and good operating practices require contin­ued review of operating systems that support the operation, thus the development of a Strategic Mine Plan. This Strategic Mine Plan provides managers, engineers and supervisors a means to improve their operations through three main objectives: 1. Reduce operating costs, 2 .. Increase production, 3. Increase mine life (reserves). These three main objectives will be reviewed in context to their current status and past performance.

Jan 1, 1999

By P. Maraboutis

Extractive industry (mining and quarrying operations), as other industrial activities, is subject to environment protection laws, regulation and standards such as the Environmental Impact Assessment directive, Natura 2000, Habitats & Birds directive, Water Framework directive etc The European Commission (EC) is aim to strengthen the EU environmental legislation to improve the (environmental and human) safety of mining activities. The mineral processing and the management of the mining waste will be covered by the new amendment of the Seveso II Directive, by a Best Available Techniques reference document (BREF) describing the Best Available Techniques of mining waste management and a new directive on the mining waste management. At the same time initiatives as the environmental liability, the energy taxation for environmental reasons and the natural resources management policy, which will have a positive impact on the protection of the environment, will affect the extractive industry operation procedures.

Jan 1, 2002

By Michael J. Feltes

In mining operations, conveyors hold one of the most important keys to productivity. Sudden belt or belt-splice failures and extended repair downtimes can contribute to low material-handling system availability. Consequently, operations and maintenance personnel should have a thorough understanding of the available splicing and repair alternatives and how each method can affect the productivity and cost-effectiveness of their operation. The two primary methods of joining belt ends - vulcanization and mechanical fastening - affect the likelihood of sudden failure and repair times in different ways. The time-honored method of vulcanization remains popular in many conveyor-intensive underground and above-ground mining operations around the world. At first, vulcanization may seem attractive because, when done properly by trained and experienced craftsmen, it can match the original belting fairly closely and give the splice a smooth, continuous surface with no edges or seams to invite snagging.

Jan 1, 1993

By F. Figge, T. Hahn

In this article we present Sustainable Value, a valuation methodology to assess sustainable value creation of companies. Sustainable Development posits that decisions must not only take into account economic capital but also natural and social capital. Sustainable Value, the methodology presented in this paper, borrows the idea from financial economics that the return on capital has to cover the cost of the capital. Capital costs are determined as opportunity costs, i.e. the forgone return that would have been created by an alternative investment. By expanding the well established logic of the valuation of economic capital in financial markets to also cover natural and social capital we provide a methodology that allows an assessment of the most efficient allocation of economic, natural, and social capital for sustainable value creation in companies. We demonstrate the practicability of the methodology by the valuation of the sustainability performance of British Petroleum (BP).

Jan 1, 2005

By Y. C. Kim

One-quarter of a century has passed since the "theory of regionalized variables" (geostatistics) was introduced by G. Matheron (1962, 1963) in France. Yet, only during the past decade has geostatistics found broad acceptance in the mining industry. Foremost among the reasons for this time lag was ignorance. The first English treatise on geostatistics was not written until Matheron (1971), and the first published text accessible to mining professionals did not appear until David (1977). Other significant reasons for the slow acceptance of geostatistics included the conservative nature of management in the 1970s minerals industry, and the fact that conventional ore reserve estimation performs reasonably well when confined to massive deposits of base metal and iron deposits having relatively low coefficients of variation in grades. In short, mine engineers and geologists were not willing to accept a new set of tools for problems that they did not see.

Jan 1, 1989

By S. R. Abt, J. D. Nelson, G. M. Smith

An empirical investigation was conducted to formulate a design criteria for predicting the beach profile of hydraulically deposited tailings. Field data were obtained from mining operations producing gold sulfides, silver, molybdenum, copper, platinum, and uranium. Site-specific parameters were collected that included the beach slopes, tailings soil properties, slurry properties, and the slurry distribution system characteristics. Each of the beach profiles were dimensionlessly plotted, and regression expressions were computed. It was determined that either a power expression or exponential expression closely predicted each beach slope. A general power expression and a general exponential ex¬pression were developed resulting in a design criteria. A procedure was formulated to determine which expression, power or exponential, is applicable to any specific site. A slope designation chart was developed as a function of the discharge, the tailings critical tractive shear stress, and the inertial forces exerted by the slurry on the beach.

Jan 1, 1987

By Zhu Mingshan, Wu Jiang, Xu Yingqin

A mathematical model to simulate spontaneous combustion of coal in goaf was developed. Under the condition of two-dimensional flaw of air through a bed of uniform mixture of coal, gob, stone etc., the model simulates the temperature rise in the air-and-particle system associated with Arrhenius particle surface reaction. The model is developed as a set of coupled non-linear partial differential equations, which include (1)mass conservation equation for oxygen, (2)energy conservation equation for gas, (3)energy conservation for solid, and (4)velocity equation for gas, that are solved numerically. An elaborate parametric analysis is made of effect of leakage air flux and position of source and sink, parameters relating to the coal accumulating character and the kinetic properties of coal on the tendency to spontaneously combust. In addition, the dynamic process of temperature rise within goaf under several conditions is displayed with picture drawn by computer.

Jan 1, 1991

By G. Schubert, H. Hoberg

A large number of diverse size reduction machines is currently available for the comminution of waste materials. Equipment selection is determined by the nature of the material to be treated and by its behavior under external mechanical stressing. Accordingly, wastes can be divided into those with elastictbrittle and those with ductile/viscous behavior. The scientific understanding of the comminution of wastes is lagging strongly as compared to that of the grain-shaped mineral raw materials. Only in a few unique cases have the fundamentals of the comminution of ductile or viscous materials been presented. The paper centers on a characterization and systematic analysis of the types of stress fundamental to comminution. On the basis of this discussion an overview is presented of the currently available technologies for the comminution of wastes, with attention centering on those machines designed for materials with ductile or viscous behavior.

Jan 1, 1998

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003

By Mark R. Rybak, James Delmonte, Travis Hartman

The City of Phoenix, Arizona designed a 7.2 km (4.5 mi) long water transmission main from the South Mountain Reservoir to the Ahwatukee Foothills Reservoir to address the growing demand for drinking water in the southeast valley. The pipeline design called for a bored tunnel in a very environmentally sensitive area. The Reach3B contract included an 2.44 m (8 ft) diameter TBM excavated tunnel, 1,847 m(6,060 ft) in length. The geotechnical investigation revealed that the tunnel would likely pass through zones of loose to moderately cemented soils (caliche). The primary tunnel support would consist of rock bolts, circular steel ribs, hard wood lagging, and mine straps. A TBM that could handle the ground conditions and allow for efficient ground support installation was required. This paper describes the construction of a small diameter rock tunnel in challenging ground conditions.

Jan 1, 2003

When multiple mines operate in an area there are social, economic and environmental impacts which cumulate over space and time. These impacts require special attention. A collective approach is required to identify, assess and manage them. No assessment of sustainability of mining can be considered complete without accounting for cumulative impacts. This paper proposes a framework and typology to deal with cumulative impacts and tests this in a coal mining area in NSW Australia.

Jan 1, 2007

By A. Zomosa

In the operation of continuous countercurrent decantation it is well known that an increase in the number of thickeners results in an increase of the fixed costs. But inversely it happens that the variable costs are reduced, i.e. the valuable material has a better recovery. The aim of this paper is to solve the problem by means of an economic balance of both parameters, in order to determine the optimum number of stages.

Jan 1, 1991

By K. N. Han, X. Xie

The dissolution behavior of palladium powder in thiourea solutions was investigated. The variables studied were temperature, stirring speed and the concentrations of thiourea, acid and ferric ion. Palladium was found to be soluble in thiourea solutions in the presence of an oxidant such as ferric ion. The dissolution of palladium in thiourea solutions was believed to be chemical-reaction controlled, with an apparent activation energy of about 25.3 kJ/mol.

Jan 1, 1997

By J. Muir

This report focuses on minimum ore block sizes that are economically feasible to mine with the vertical crater retreat (VCR) method. In 1985, Homestake Mining Co. began a program to bring several small block VCR stopes on line. This report examines these experimental stopes, including design parameters, ground control, drill patterns, secondary blasting, and mucking. Cost and scheduling comparisons are made with mechanized cut-and-fill and open cut- and-fill methods.

Jan 1, 1987

By Sylvain Duchesne, Claude Bazin, Robert Grant

Grinding simulators are now widely available to assist in the selection of circuit operating conditions or flowsheet designs that yield a given product size distribution. These simulators do not inform of the impact of the grinding product size distribution on subsequent flotation stages. This paper presents a method to predict the effect of fineness of grind on a flotation bank operation. Application of the method is illustrated with data from two Canadian concentrators.

Jan 1, 1995

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

With increased emphasis on controlled blasting, which is the first and least-costly stage of comminution, ore grindability and plant throughput can be increased by 5% to 10%, and energy savings of up to 10% appear possible. Crushing and grinding efficiencies are presented for ore blasted under regular and adjusted field conditions. An economic analysis of drilling and blasting through crushing and grinding is presented, suggesting that cost savings approaching 10% may be achieved.

Jan 1, 1998

By R. D. Willette

The Hector Mine deposit in the California Mojave Desert has a magnesium-rich clay that formed when lithium and fluorine were introduced into isolated fine lacustrine volcanic sediment during the Pliocene. The intensely deformed deposit has been supplying the highest grade thixotropic clay to the coatings industry for over half a century. A thixotropic clay displays the property of changing from a gel to a sol when shaken, and increases in strength upon standing.

Jan 1, 1995

By Alex Ruzycki

Gold Fields-Mesquite is a 7.5 million ton per year heap leach operation located in the Maj ave Desert of Southeastern California. Extraction of gold is carried out on multiple lifts, with over 33.3 million tons of ore leached since the inception of operations in 1985. The delineation of the gold left in heap residue is a formidable task. Gold removed from active leach areas can be routinely monitored through sampling of emerging solutions but exact recoveries from specific heaps remains nebulous due to factors such as cross flow between sections buffering effects from multiple lifts, and releaching. In order to better quantify ultimate heap recoveries and increase releach efficiency, Mesquite initiated a residue drilling program. The project progressed through an evaluation of sampling protocol, drilling of residue by reverse circulation, entry of assays into a software package capable of producing grade-based contour maps, and a production scale releach test that evaluated the system's ability to predict residue grade.

Jan 1, 1992