Search Documents

By Carl S. Vender

Knife River Coal Mining Co.'s Beulah Mine is a multiple-seam lignite operation located in western North Dakota. The mine began production in 1963 with annual production of 450 kt (496,000 st). It now produces 2.2 Mt/a (2.4 million stpy). As development progresses, operations advanced into more complex geologic areas. Various techniques have been analyzed to maximize coal recovery in a cost-effective manner. Additional studies are ongoing to determine what changes will be implemented as deep, wet sands are encountered in the reserve area. Knife River Coal began as an underground operation in 1924 at Beulah, 120 km (75 miles) northwest of Bismarck. In 1950, the operation converted to a combination underground and surface mine. The underground segment was closed in 1952. Development of the existing reserve area south of Beulah began in 1963. About one-fourth of the acreage under permit (Fig. 1) is sufficient for 10 years at current production rates.

Jan 1, 1991

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

By D. Harney

Accurate measurement, tracking, and planning are vital for efficient utilization of energy in any mining operation, the major focus of this paper. This can be done with a number of assessments: 1) accurately measure KWH usage and track peak demand periods first; 2) identify the electrical equipment that affects your usage and the conditions that require it to be running; 3) remotely monitor and control as much equipment as possible, especially larger pieces of equipment; 4) with your utility determine that you are on the most suitable rate for your usage profile, then understand how your utility company calculates your electrical bill; 5) recognize how production affects energy usage and utility costs; 6) keep historical records of everything you monitor; 7) make information, live and historical, available to everyone; and finally, with the knowledge of your equipment and energy needs, automate controls that you have identified to optimize your energy usage and time of usage.

Jan 1, 2007

By Meliton M. Garcia, Satya Harpalani

This paper discusses the results of an investigation carried out in an underground mine to characterize the volatile by-products adsorbed on airborne particulates following the detonation of four common explosives including ANFO. The primary objective of this study was to determine if any organic amine compounds, particularly nitrosamines, and any polycyclic aromatic hydrocarbons were produced and trapped in the dust that a miner might inhale during the workday. The production of these substances is of great concern because of their suspected carcinogenic nature. The results of the study indicated that a large variety of the by-products are adsorbed on the particulates generated, and thus remain airborne following the detonation of explosives. The major by-products retained by the dust were bis(2-ethylhexyl) phthalate, and aliphatic hydrocarbons with carbon chains ranging from C12 to C28. One explosive, a water gel, produced the polycyclic aromatic compound, trimethylnaphthalene. No nitrosamine compounds were detected.

Jan 1, 1989

By K. N. Han, Q. Xu

The adsorption behavior of gold in ammoniacal solutions on activated carbon was studied. The gold adsorption capacity of the activated carbon and the recovery efficiency were examined. The parameters affecting the adsorption of gold on the activated carbon included temperature, agitation speed, the concentration of cation and anion and the concentration of ammonia. It was found that the maximum gold adsorption was about 10 kg/t of carbon. The recovery of gold by the adsorption, from ammoniacal solutions was found to be dependent upon the initial gold concentration. Under experimental conditions, a gold recovery of 98% was obtained after 120 hrs of adsorption. It was also found that the initial adsorption rate was relatively fast, when compared to the entire adsorption period. The apparent activation energy for the adsorption was determined to be 15.8 kJ/mol. It was believed that the kinetics of gold adsorption on the activated carbon was controlled by pore diffusion.

Jan 1, 1997

By R. Hogg, E. Kaya, H. Cho

Investigations were performed on fine grinding of bituminous coal in a laboratory-scale pulverizer. The results indicated that the breakage behavior at relatively coarse sizes (i.e., greater than about 20 µm) is essentially "normal." However, at fine sizes (i.e., less than about 10 m), there is clear evidence of reagglomeration. A simplified population-balance model for simultaneous growth and breakage is formulated. Breakage rates and breakage distributions were assumed to follow the patterns typically observed in simple grinding systems. It is recognized, however, that solid particles and agglomerates may exhibit different breakage behaviors. Agglomeration rates are assumed to be determined by contact probability, i.e., by the relative numbers of interacting particles. Based on comparisons between model simulations and experimental data, it appears that agglomerate rebreakage rates and fragment size distributions are quite different from those for solid particles. The result is that product size passes through a minimum and then increases with time as agglomeration begins to dominate.

Jan 1, 1998

By Numan Elmas

Barite deposits located in Dinek and surrounding region have important economic features with their large reserve capacity for Turkey. The objective of this study is to elucidate geological and depositional characteristics in terms of. site investigation and chemical analysis. In order to do this, geological area of about 300 km2 was examined and detailed geological map was constructed. It was observed that Barite mineralization in these deposits was occurred in carbonate and pelitic rocks of Lower Cambrian-Lower Ordovician. Deposits were exposed to advanced diagenesis regional metamorphism and tectonics that rotated and deformed the barites; therefore, barites shows secondary veins, brecciate and fracturing structure. Even though, a few light isotope values of barites may suggest hydrothermal and exhalative sedimentary characteristics or possible mixing with magmatic fluids, generally heavy isotope values indicate that the sulfate ions were supplied from coeval seawater and, many of sedimentary features and petrological, geochemical characters support dominantly sedimentary origin.

Jan 1, 2005

By P. D. Rao, D. E. Walsh

A pilot-scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2 in.) crushed ore from Ester Dome, AK. 9.04 t (9.94 st) of crushed ore were sampled and processed through a Pan-American jig-Wilfley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/t (22.4 oz/st). The feed grade to the plant was calculated at 1.71 g/t (0.05 oz/st). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/t (0.042 oz/st), 1.30 g/t (0.038 oz/st), and 5.47 g/t (0.16 oz/st, respectively. Significant coarse, free-milling gold values were shown to remain in the, jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1992

By Gordon D. House, J. B. P. Sawyer

The Bannockburn gold prospect is a new discovery in Ontario's oldest gold camp at Eldorado, eastern Ontario. Mono Gold Mines Inc. of Vancouver, British Columbia, acquired the property in 1980 and in 1984 discovered a previously unreported gold bearing quartz vein system to the northeast of the old Bannockburn Mine. Extensive diamond drilling carried out since 1985 defined a quartz vein system over 475 m (1 ,500 ft) of strike to a depth of over 105 m (350 ft). Limited underground exploration by decline to the 22.9 m (75 ft) level in 1988 confirmed the continuity and tenor of the quartz veins. Gold occurs as native metal with minor sulphides and bismuth tellurides in a quartz carbonate vein system within metasedimentary and metavolcanic rocks of the Grenville Province. Metallurgical test work on a surface bulk sample was favourable. Estimates of drill indicated reserves have been made as well as reserves based on the limited underground exploration.

Jan 1, 1989

By V. T. McLemore

The Steeple Rock district in New Mexico is a major epithermal gold-silver district that exhibits district zoning. Five types of ore deposits occur within the district: •base-metal veins (with gold and silver) form the center of the district and occur along the Carlisle fault, •gold-silver veins along northwest-trending faults and outward from the base-metal veins, •copper-silver veins along the margins of the district, •fluorite veins along the margins of the district, and •manganese veins along the margins of the district. Areas of older acid-sulfate alteration occur throughout the district and also exhibit the following zoning: massive silica/chert zone (inner), silicified zone and clay zone (outer). This alteration overlies regional alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow, but older, epithermal hot-springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1996

By H. J. Marais, P. C. van Aswegen

The Biological Oxidation (BlOX®) Process for the treatment of refractory gold ores was commercialized in 1988. During the last decade, the technology has developed into a mature, commercially viable process, with five additional operations commissioned, including operations at Sao Bento in Brazil, Harbour Lights and Wiluna in Australia, Ashanti in Ghana and Tamboraque in Peru. With ongoing development, the efficiency and cost effectiveness of the process have both improved, making it an attractive alternative to conventional refractory treatment processes such as roasting and pressure oxidation. The bacterial culture is robust and can withstand the normal fluctuations experienced on an operating plant. The plants are simple to operate, making it ideal for remote areas. The scale-up potential of the process has been proven, and it can be applied to large refractory ore bodies. The process is environmentally friendly. Neutralization of plant effluents produces precipitates that comply with the most stringent environmental regulations.

Jan 1, 2000

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which enables completely new designs of conventional shell and tube configurations. This article explains the principle and application of this self-cleaning heat exchange technology and also pays attention to an actual case of a revamp of the severely fouling exchangers of a conventional multi-effect evaporator into a self-cleaning configuration. Possibilities for the revamp of conventional exchangers suffering from massive and very hard scale deposits are found in a variety of metallurgical processes, such as: The refining of nickel, the production of alumina from bauxite and many others.

Jan 1, 2003

By Des B. Bolton, Neil P. Boland

Typically, environmental work on mine sites in Northern Australia involves addressing an individual problem as it arises. However, individual mining companies are moving toward a more holistic approach to managing the interactions between the environment and the mining process and are thus pre-empting environmental problems. This paper presents a broad overview of this holistic approach and provides a few examples, drawn from our own experience, which illustrate some of the tangible benefits to be gained from Environmental Planning.

Jan 1, 1991

By Marc E. Orman, Mark E. Smith

Regulatory and environmental concerns continue to broaden the range of mine wastes that must be capped with low permeabili­ty liner systems at closure. The mining industry has been a leader in developing liner technology for leach pads and tailings impoundments, but it is a newcomer to cap designs. Closure of waste piles, leach heaps and tailings require special design con­siderations. Factos such as differential settlement, surface ero­sion, veneer stability, vegetation and burrowing animals must be considered.

Jan 1, 1996

By Ethan B. Eilertsen

Titanium solves corrosion, maintenance and environmental problems in many reactor and autoclave applications. Titanium clad construction permits autoclave designers a great deal of flexibility combined with significant cost reduction. Titanium alloys can be selectively applied in specific regions of the autoclave to accommodate local environmental conditions. Resistance to general corrosion, crevice corrosion, abrasion, and ignition conditions can be accomplished selectively and economically. Explosion clad pressure vessel fabrication and performance have been proven through three decades of experience.

Jan 1, 1997

By Robert L. Bates

The field of industrial minerals and rocks includes such a wide diversity of materials and occurrences that communication is essential to foster a sense of "belonging? among geologists and other professionals. Besides, exchange of ideas and information is essential in meeting the needs of an ever-expanding world economy. A survey of the field shows to what an extent such communication--especially in the form of conferences and their proceedings--has increased during the past 25 years.

Jan 1, 1995

By Earle J. Klohn

Tailings disposal has rapidly become an area of increasing importance to both existing and planned mining operations. In recognition of the significance of this topic, MINING ENGINEERING is presenting a series of articles on tailings disposal. The first, published in June, outlined some site criteria that influence tailings disposal and some of the design options available to meet these criteria. The following article explores in more detail important design criteria for tailings dams and provides several case study illustrations.

Jan 7, 1981

By Dennis K. Mortensen

Improvements in metallurgical performance are continually being made in the attempt to achieve the metallurgist's goal of maximum concentration, minimal loss of recovery and at costs that maximize profit margins. Innovative technological advances provide a means for the metallurgist to more thoroughly understand the mechanisms of separation and foster new ideas from old. Problems associated with the implementation of new technology can be overcome effectively if the metallurgist thoroughly understands the metallurgical systems with which he is working.

Jan 1, 1991

By Remo Grandori, Fabrizio Antonini, Giorgio Dolcini

The paper describes the anticipated and the encountered geology, the TBM selection concepts and the machine special features, the tunnel sections, the achieved advance rates and the geological problems, the machine behaviour and the main setbacks caused by ground conditions the Authors also discuss the scopes for possible improvements to double telescopic shield machines, with special reference to their application under extreme geological conditions such as those that were met in the course of Los Rosales Tunnel excavation.

Jan 1, 1991

By Alan C. Noble

Ore reserve estimation is a multi- disciplinary process involving not only tonnage and grade estimation (resource estimation), but also consideration of technical and legal aspects such as mining the deposit, beneficiating the ores, and selling the product. This paper provides a background to under- standing resource estimation including geologic modelling, manual estimation methods, conventional computer methods. and geostatistical methods. Mine planning, metallurgical studies, legal/environmental, and marketing considerations are also discussed as they relate to estimating ore reserves.

Jan 1, 1991