Search Documents

By Jorge Martinez

The Muck Valley Hydroelectric Project in Northeastern California required construction of a 3.65 meter tunnel through 6,623 meters of mixed volcanic flow deposits within a critical time frame. As Engineer and Construction Manager for the Project, Morrison-Knudsen Engineers invited bids for both Drill and Blast as well as Tunnel Boring Machine methods, selecting a contractor proposing a TBM designed and built specifically for this project which could excavate a wide variety of materials and maintain acceptable progress rates to complete the work within schedule. Tunnel lining as required included shotcrete with metal fibers and full circle concrete.

Jan 1, 1989

By D. L. Petersen, C. R. Nelson, P. M. Bergson, B. K. Nelson

Membrane waterproofing systems in large tunnels cause the partial decoupling of the concrete liner from the rockbolted and shotcreted reinforced rockmass. This decoupling leads to a loose fit of the liner in the excavation when shrinkage from cooling and moisture loss occurs. This increases tensile stresses which require either the addition of reinforcing steel in excess of common European practice or the potential for liner cracking. Hot weather concrete placement and cold weather service conditions increase the magnitude of the problem, while creep of the rockmass reduces it. Contact grouting also reduces, but does not eliminate, the problem.

Jan 1, 1991

By M. Kaya

The main purpose of this study was to design a modular/mobile coal preparation plant with a capacity of 300 t/h for Seyitömer B3 vein (almost 70% of the whole SLI deposit). Firstly, coal washing properties and washability curves were determined by sink and float tests. Then, equipment sizing, selection, flow sheet development, economic evaluation, investment and operating costs were determined for coarse (-150+18mm), fine (-18+0.5mm) and slime (-0.5+0.1mm) coals. Economic evaluation of the proposed flow sheet showed the feasibility and profitability of the investment.

Jan 1, 2006

By D. R. Zeni

Today's mine development requires the safe, expedient and economical construction of vertical shafts for both ventilation and access. This construction must be accomplished within diverse ground conditions. Advancements in large-diameter shaft drilling have led to many exceptional mechanical refinements in shaft-drilling technology. The author traces the history of the equipment and methods employed by the large-diameter shaft-drilling industry and explores the likely paths of future development. Case histories that illustrate the adaptability of shaft drilling as a versatile tool for advanced, worldwide mining operations are cited. Safety, scheduling, costs, environmental impacts and capabilities are discussed.

Jan 1, 1996

By W. L. Han, Y. D. Zhang, X. C. Li

Meta-systhetic technique for large systems engineering has been placed on the agenda. The meta-systhetic A1 approach should involve the integration of digital and knowledge info, from qualitative to quantitative analysis, etc. Some algorithms of meta-systhetic technique such as ANN-ES and GA-ANN are introduced. A case study follows - mining conditions evaluation by meta-synthetic A1 methods, including: setting up the structure of evaluation indexes system, deciding their grade of membership by ANN-ES algorithm; determining the weight values of evaluation factors by GA-ANN algorithm; and developing the integrated evaluation model.

Jan 1, 2002

By Thomas W. Healy, David V. Boger, Yee-Kwong Leong, Lee R. White, Peter J. Scales

The concentration of mineral slurries by conventional thickening devices is discussed. The role of additives on the compression of mineral slurries is also examined. Results for a range of flocculation conditions are presented. The compression of flocculated mineral slurries is found to be highly dependent on the fundamental particle-particle interaction forces and hence, the rheology of the particulate fluid. It is demonstrated that a detailed knowledge of the properties of both the mode of operation of the thickening device and of the solid/liquid interface is required for improvement in the rate and in particular, the extent of dewatering.

Jan 1, 1995

By Charles H. Arnold

This topic addresses historic and current techniques of excavating, supporting and lining tunnels of 4 m (13.1 ft) and smaller. Special considerations relate to the economics of working in close quarters and the sizes of tunnel which achieve the required facility in the optimum economic manner are discussed. The excavation discussion includes TBM, conventional and special techniques for hard rock, soft ground, subaqueous, free and compressed air tunnels. Internal and external support methods discusses timbering, steel ribs, bolting, strapping, shotcreting, grouting, and freezing. Lining methods include cast-in-place concrete, concrete pipe, segmented linings, shotcrete, and others.

Jan 1, 1981

By Thomas H. Wake, Timothy M. Tower

A continuing trend in raise drilling is the movement toward increased automation. This paper discusses the reasons for automating a raise drill, which include labor saving, faster and smoother operation, quicker response to blocky ground, and improved data logging and diagnostics. It gives a "wish list" of features when automating a raise drill, from simple shutdown control through unattended operation. It discusses the principles involved in closed loop control of a sluggish mining machine with large inertia, and covers functions such as data logging and remote control. Results are presented from a field test on a production raise drill.

Jan 1, 1991

By Anthony J. Ranalli, Florentino B. Maestas, Katherine Walton-Day, Richard W. Healy

Water movement and water chemistry were monitored in the unsaturated zone at two sites in fluvial tailings deposits along the Arkansas River near Leadville, Colorado. One of the sites was remediated by the incorporation of lime and biosolids into the soil. Preliminary results, based on data collected during the 11 months following remediation, indicate that differences between the two sites can largely be attributed to heterogeneity of the deposits. Remediation has increased the alkalinity in the upper soil zone, but as of yet, there is no indication that soils at depths greater than 30 cm have been affected.

Jan 1, 2000

By S. G. Haycocks, M. Karmis, C. Haycocks

Risk assessment is a primary factor in the decision to mine some near surface orebodies, such as limestone, by either surface or underground methods. Identification and quantification of risks demonstrate that environmental concerns are greater for surface operations than underground, and may include such factors as runoff, spoil piles, aesthetics, dust, and large site reclamation. Risk assessment also includes local public feeling towards surface and underground operations while considering the balance between environmental impacts and the economic effects of mining on the local community. A complete understanding of the risks involved permits a comprehensive and accurate comparison between the two mining alternatives.

Jan 1, 1992

By Y. Akin, M. S. Celik, T. Batar, F. Arslan

Despite its importance in various diverse industries, research on beneficiation strategies of boron minerals has not received enough attention. Boron minerals are primarily upgraded by wet processing methods. However, severe environmental constrains have accelerated the development of dry processing techniques such as calcination. Interestingly, the boron minerals colemanite, ulexite and borax undergo decrepitation, shrinkage and expansion, respectively, upon heat treatment. Each mineral then requires a different beneficiation scheme. In this study, laboratory and pilot-plant studies conducted in our laboratories on the calcination of boron minerals are briefly reviewed and their implications to commercial operations are discussed.

Jan 1, 1999

By S. K. Kawatra, T. C. Eisele

In many mining operations, particularly northern open-pit mines, large seasonal variations in grinding slurry temperature can occur. It is shown in this paper that this temperature shift can cause a winter-time loss in autogenous grinding efficiency of as much as 20% if it is not controlled. Laboratory experimentation indicates that much of this effect is due to increases in slurry viscosity as the temperature is decreased. An additional effect may result from changes in rock strength upon freezing, for which possible mechanisms are discussed. However, no effect clearly resulting from rock strength changes has been definitely confirmed.

Jan 1, 1992

By Y. Luo, S. S. Peng

This paper presents some results obtained from research on long-term subsidence over and near chain pillar systems - the area available to long-term subsidence in longwall operations. Although the long-term subsidence for most longwall operations is insignificant, it does exist in some cases. In the cases that showed significant long-term subsidence, it was found that the development process could be expressed by an exponential decaying function. The stability factor of the chain pillar system and the potential for long-term subsidence are the two most important factors that control the magnitude and development characteristics of the long-term subsidence process.

Jan 1, 2000

By H. Pieterse, K. S. Fraser, J. R. Goode

The Goldstrike autoclave plant is designed for the pressure oxidation of 1363 t/d (1500 stpd) of refractory gold ore. The plant was commissioned in early February 1990 over a one week period - an unusually short period for a plant of this complexity. The rapid plant start-up is attributed to certain detailed design and control aspects of the plant. This paper discusses key features of the autoclave plant with emphasis on the design of the splash/flash system of heat recovery and the control systems. Commissioning and plant operations over the first three months are reviewed.

Jan 1, 1990

By M. Spangler

FirstMiss Gold installed a supervisory control system that is based on Pavilion Technology's Process Insights neural-network software and Oil System's PI data historian. The first successful control loop involved controlling the limestone feed rate to the neutralization circuit. The resulting improvements in the control of the circuit resulted in savings of $31,000 per month. Although it was the primary goal of the system, supervisory control of the preconditioning circuit was not achieved. However, information gained during the modeling suggested process modifications that resulted in cost savings of $54,000 per month in the preconditioning circuit.

Jan 1, 1997

By A. D. Unsted

The Premier mine has been in existence for over 75 years and is closely woven into the glamour of the history of South Africa. A note on the geological formation of the diamond pipe and the gabbro gives a clearer overall picture of the mine. Mining methods for operations above and below the gabbro sill are briefly discussed. Ventilation arrangements for mining above the sill are briefly described and possible ventilation arrangements for mining below the sill are discussed in more detail. Note: conversions to S.I. units are not exact as rounding has been done.

Jan 1, 1980

By Mark R. Stanton

Geochemical and mineralogical analyses of 46 samples from six drill cores in the Mayday mine pile near Silverton, Colorado, demonstrate wide variability in trace metal contents with spatial location. This variability results from the original geochemical composition of mined rocks, mixing of ore and non- ore rocks during emplacement of the pile, and weathering since rocks were placed in the pile. Weathering reactions are controlled by factors such as pile thickness (depth), water availability, microbial activity, and mineral dissolution and formation kinetics. These factors result in variable redistributions of trace metals from primary (ore) to secondary (weathering products) minerals within each core.

Jan 1, 2000

By Jeff W. Butwell

Mill flotation tailings impounded at the Gooseberry Mine site between 1976 and 1984 were determined to be an economic source of gold and silver recoverable by standard heap leach technology in conjunction with feed agglomeration. Metal recovery at 85 percent Au, 75 percent Ag is attained on properly agglomerated (pelletized) tailings which average 85 percent -75 micron. Because the impounded tailings averaged over 18 percent moisture (32 percent moisture maximum at depth) in place behind the storage dam, the mining method, mixing and agglomeration technique, and materials handling practice were major considerations in making this operation a financial success.

Jan 1, 1990

The definition of sustainable development is often taken from the so-called “Brundtland” report, requiring that activities of the current generation not detract from the potential welfare of future generations. Mining is often held up as unsustainable in this regard, since the extracted resource is non-renewable. Yet Brundtland’s definition of sustainable development also requires that the current generation address the disparity in welfare across the globe, a facet of Brundtland’s report that most have ignored. This paper examines the impact of mining on the welfare of the poor, empirically assessing mining’s contribution to this second facet of sustainable development.

Jan 1, 2004

By Helen Leung, Colin R. Phillips

The performance of personal alpha dosimeters in mixed radon daughter and thoron daughter atmospheres in Ontario uranium mines is described together with monitoring developments which enable the radon daughter working level to be determined separately. The theoretical bases for continuous and integrated working level measurements based on individual and gross counts are presented in terms of the weighting factor for combining the thoron daughter working level with the radon daughter working level, and in terms of the in-growth time of the air. Implications for the determination of working level in the presence of thoron daughters are discussed.

Jan 1, 1981