Search Documents

By David L. Moffatt, Leon Peters

A unique electromagnetic pulse sounding system for the detection and identification of geological and man-made anomalies which represent hazards in hard rock rapid tunneling operations is described. The main features of the system including a periodic video-type pulse interrogating signal and a probe structure that permits operational modes which either "see" or are "blind" to homogeneous-type targets are reviewed. The results of experimental pulse measurements on targets buried in the overburden and in a limestone medium are presented. Since the electrical properties of limestone are not radically different from those of a hard rock medium, conclusions based on these data should be valid for a hard rock media also.

Jan 1, 1997

By Gary A. Almeraris, Thomas F. Peyton

This paper describes the innovative procedures employed during the construction of 3 deep shafts within the confines of New York City. The shafts, which varied in diameter from 1.8m (6ft) to 7.3m (24ft) and had an overall depth of 199m (650ft), were excavated by both mechanical and conventional methods. These were subsequently concrete lined, clad steel riser pipes installed and associated surface structures were constructed. Tricky surface rock blasting coupled with the unearthing of unexpected obstructions caused constant uncertainty during the excavation phase. In addition, the necessity of handling men and material in restricted yet deep openings required the development of a safer and more productive shaft construction procedure.

Jan 1, 1989

By Shuang Shuang Huang, John Fillos

Ozonation was evaluated as an alternative treatment process for leachates of municipal landfills. The study was carried out on leachate from the Fresh Kills Landfill, New York City. The leachate has strong tea color and BOD5 ranging between 90 mg/L and 130 mg/L. The average COD, TOC and NH3-N concentrations were 1800 mg/L , 550 mg/L, and 665 mg/L, respectively. The kinetics of the process were studied in a sparged batch reactor by developing concentration- time profiles for residual color and TOC. Continuous flow experiments were then carried out at two selected contact times. The process was found to be effective in the treatment of leachates for color and TOC removal.

Jan 1, 1992

By John Reynolds, Robert Sloan

The Escondida copper mine is located in the northern Atacama Desert of Chile at an elevation of 3,050 m. approximately 160 km southeast of the port of Antofagasta. The mine is a joint venture between BHP-Billiton, Rio Tinto, a Japanese consortium and the International Finance Corporation. The most recent expansion, Laguna Seca, has increased the total capacity to the level of 220,000t/d ore throughput. The ore body, a typical porphyry deposit, is situated on the major Chilean west fissure fault system and contains primary sulphide ore grades between 0.6% and 2.0% copper. Primary sulphide mineralization consists of chalcocite pyrite, chalocopyrite, bornite and covellite. Significant copper oxides overly the sulphides in many areas.

Jan 1, 2005

By Guillermo Chong Díaz

A brief overview of industrial mineral exploration and exploitation in Chile is given. World class deposits of salt, lithium, nitrate, and iodine are present in northern Chile. The potential for further exploration and exploitation of these deposits, as well as the substantial reserves of other mineral commodities such as gypsum, anhydrite, volcanic rocks, and borates are discussed. In conclusion, industrial minerals mining in Chile has considerable potential, particularly as joint ventures between foreign and domestic companies. This has been demonstrated in the extraction of nitrates, lithium, iodine, and diatomites. However, as outlined in this paper, a number of factors need to be overcome before the true potential of the Chilean industrial minerals industry can be realized.

Jan 1, 2001

By Dipak D. Shah, Sajjan K. Jain

An interceptor sewer, 2103 linear meters (6900 Ft), 1.52 meter (5 ft) in nominal diameter, is installed by a direct pipe jacking system utilizing a remotely controlled fully automatic slurry shield machine called "Unclemole". The system involves placement of custom designed fiberglass pipe with Unclemole. The sewer alignment is along a heavily travelled thoroughfare in Staten Island, New York with invert varying from 20 meters (65 ft) to 28 meters (92 ft) beneath the road surface, and passes through soils of Glacial and Cretaceous origin. Dewatering was carried out at the jacking and receiving pits. Details of ground conditions, the pipe jacking system and method, and tunneling experiences are herein described.

Jan 1, 1991

By David Jenkins

Grefco Inc. operates two diatomite mines in the western Santa Ynez Mountains. The larger of the two mines, the Palos Colorados Mine, is located approximately seven miles southeast of Lompoc. The Miguelito Mine is located about two miles south of Lompoc on the west side of the Miguelito Canyon. Diatomite from the Palos Colorados and Miguelito mines is trucked to the Grefco plant at Lompoc for processing (Figure 1). HISTORY Grefco, Inc. evolved from the originating Dicalite Company which in 1929 began operations at the Walteria plant in the Palos Verdes Hills south of Los Angeles. In 1942 Dicalite leased the Palos Colorados mine at Lompoc. In 1944 the Dicalite Company was purchased by Great Lakes Carbon Corporation.

Jan 1, 1995

By J. C. Harrison

When Exploraciones Eldorado, S.A. de C.V. finished their first phase of reverse circulation drilling at their La Trinidad property in Sinaloa, Mexico they began immediately with permitting and engineering activities. The first phase of drilling lasted four months and ended in April, 1994. The second phase of drilling ran from May through September of 1994. From May through December, 1994, Exploraciones Eldorado performed the permitting and engineering work for their La Trinidad heap leach mine. The mining permit was submitted to the regulatory agencies in February of 1995 and the first draft of the feasibility study finished one month later. The report outlines the permitting and engineering activities that took place during the second half of 1994.

Jan 1, 1996

By ev, Ze&apos Reches

The growth of networks of shear fractures is explored in a series of experiments with samples of wet clay. The samples are subjected to plane strain deformation in a rigid apparatus. The individual fractures observed on the upper surface of the clay samples grow longer by three mechanisms: in-plane propagation, off-plane propagation and coalescence. New, active fractures cut and displace older, less active ones. The lengths of individual fractures display lognormal distribution in most cases and power distribution in fewer. The calculated length parameters in the experiments, as well as in three field cases discussed here, suggest that the fundamental parameters in fracture analysis are the normalized cumulative length and the length of the shortest fracture measured.

Jan 1, 1986

By W. E. L. Minter

The most important Witwatersrand gold placers occur on extensive unconformity paleosulfaces that were produced during protracted periods of fluvial degradation. The erosional etches on what was generally unlithified sub-strate indicate that low sinuosity erosion patterns prevailed. The transport systems were dominantly braided fluvial with a minor debris-flow component. The placer sediments were non-cohesive sands and gravels. They were evidently transported by fluctuating, yet perennial, discharges across extensive, low relief braid plains, not far from littoral environments. Progress made in understanding heavy mineral transport processes now emphasizes the importance that selective entrainment probably had in producing concentrations. Cognizance that these characteristics are not unique to the Witwatersrand should be taken into account when designing exploration models.

Jan 1, 1991

By R. W. Bartlett

Aeration curing, over- a long duration in wet- red stockpiles, shows promise as an affordable pretreatment method for oxidizing gold encapsulating sulfide minerals, and possibly organic matter, in low grade refractory ores. Following aeration pretreatment, the ore is reclaimed, neutralized, and cyanide leached by conventional practices. Large tonnages of subeconomic material, including mine stripping waste, may he converted into ore by this new technology. The results presented show that a successful application of this technology will likely require crushing to about -2 cm (-3/4 in.), followed by aeration in a wet stockpile for long periods, up m three years. Natural convection may he inadequate, hut forced air ventilation, at modest pressures and power consumption, is affordable.

Jan 1, 1991

By Lars Olaf Höglund

MiMi has been set up to be i) visionary, ii) strategic and iii) long-term. The planning as well as the executive phases involves industry, academia and authorities in close co-operation. MiMi focuses on improved, economically efficient management of mining waste, a challenge that requires combined and integrated research efforts across discipline boundaries. The MiMi programme is financed by the Swedish Foundation for Strategic Environmental Research (MISTRA) with support from the mining industry. The first programme phase covers the period 1997 - 2000, with intentions for additional phases. Planning, experience and results from the first programme period are highlighted. INTRODUCTION Most of the mining activities in Sweden takes place in the No

Jan 1, 2000

By Richard R. Klimpel

This paper discusses some important industrial interactions between size reduction and downstream froth flotation processes. Experience gained at the industrial level is clearly indicating that how size reduction circuits are designed and/or operated can have a significant impact on froth flotation beyond normal considerations of particle size, liberation, etc. Three specific interactions will be discussed: 1) the impact of steel grinding media versus autogeneous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources; 2) the importance of appropriately utilizing the electrochemical window that is created in the grinding to enhance sulfide mineral recovery by froth flotation; and 3) the interaction of particle size distribution with collector dosage and frother type.

Jan 1, 1995

By M. Abdel-latif, R. W. Bartlett, P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines was designed and operated. A nontransferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained above 1673 OK (1400°C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbonmonoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pres- sure and average reactor temperature. The interaction of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1995

By Hans Skretting, Abraham A. Dor

This paper briefly reviews the historical development of the Rotary Kiln-Electric Furnace Process, which was first applied commercially to the treatment of qarnieritic ores in New Caledonia in the mid-fifties. It describes various technological improvements introduced, since, in industrial plants or developed in pilot facilities where a wide variety of nickel oxide ores has been treated success- fully over the years. Major categories of ores are characterized. The effect of their physical and chemical properties on their performance in the electric furnace is discussed. The relationships between ore composition, ferronickel grade and slag composition are analyzed and their effect on slag and metal tapping temperatures, nickel recovery, and electrode voltage are discussed.

Jan 1, 1979

By G. Troly, M. Esterle, B. Pelletier, W. Reibell

In New Caledonia, ultramafic formations occur on 7,000 square kilometers. Weathering of peridotites leads to profiles of alteration and nickel concentrations. Complete profiles are composed of two main groups of horizons: 1. Limonitic, mainly composed of iron hydroxides 2. Saprolitic, partly composed of magnesium and iron silicates Shape and mineralogical composition of saprolitic horizons are chiefly affected by the nature of the bedrock: types of peridotite and their degrees of serpentinization. On the other hand, morphology (plateau, terraces, slopes, piedmont) is an important factor. Ore-bodies are inside saprolites; their outlines are determined by the grade of nickel and tonnage economically mineable. Information about geology, morphology, geochemistry, and mineralogy are given in this paper.

Jan 1, 1979

By Ricardo Gomez, C. T. Ogryzlo, A. A. Dor

This paper reviews the historical background leading to the development of the project. It gives a description of the exploration program and resulting geological and ore reserve information together with plans for mining. A discussion is included of the three processes investigated for the project: 1. Rotary Hearth and Magnetic Concentration 2. Shaft Furnace and Electric Furnace 3. Rotary Kiln and Electric Furnace Results of pilot plant campaigns conducted at Fiskaa, Norway, and Riddle, Oregon, on the process chosen for the production of ferronickel are presented. The paper continues with a review of the considerations involved in selection of commercial plant equipment and concludes with comments on the current status of the project.

Jan 1, 1979

By A. K. Bakshi

In cold regions, rinsing of spent cyanide from leach heaps is stopped during winter and is resumed again after the snow melts. The effect of this idle time on the overall removal process was studied in this experiment. Samples were collected for rinsing tests from one heap at a gold mine near Fairbanks, Alaska. Continuous and interrupted rinsing of this sample were carried out in test columns. The rinse solution was analyzed at regular intervals to determine the rate of cyanide removal from the solids. It was found that total cyanide concentration per rinse cycle for interrupted rinsing test was higher than for the corresponding continuous rinsing test. As a result, interrupted rinsing required less rinsing cycles than continuous rinsing.

Jan 1, 1995

By McDonald E. Wrenn, Narayani P. Singh, Victor E. Archer, Ceno Saccomanno

Fourteen uranium miners' lungs from Colorado plateau were collected at autopsy and the concentrations of 238U, 234U and 230Th were determined by radiochemical procedures utilizing solvent extraction - alpha spectrometric techniques. The uranium and thorium isotopes are in near equilibrium with average concentrations of 238U, 234U and 230Th being 89.3, 95.2 and 91.1 pCi/kg respectively. The combined average radiation dose rate to lung from these three isotopes is about 24.2 mrad/year at death excluding the unmeasured contribution from the 226Ra and daughters. The average concentration of 230Th is about 65 times higher than the mean concentration of 230Th in lungs of non-miners dying at comparable ages from the same region.

Jan 1, 1981

By Graham Andrews

Experiment shows that the microbial degradation of pyrite does not necessarily proceed stoichiometrically. Under some conditions sulfur is oxidized preferentially leaving something approaching iron in composition; under others, the pyrite is converted almost to elemental sulfur. A kinetic model for the process based on three elementary biochemical reactions can explain these observations. The diffusion of sulfur along grain boundaries and dislocations in the solid pyrite uncouples the oxidation rates of sulfur and iron from the requirements of stoichiometry. This mechanism also explains qualitatively why bacteria adsorb preferentially at dislocation sites on pyrite surfaces, why they form "pits" at these sites, and why amorphous pyrite is more readily degraded than pure crystals. The rate-limiting step for pyrite oxidation is discussed

Jan 1, 1989