Search Documents

By R. G. Hite, R. G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, devel reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mechanics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1992

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

A digital computer program has been developed to mathematically simulate the effect of limited changes in feed rate on the grinding circuit of an operating mill. The data on which the program is based was supplied by the staff of the mill in question. Samples taken around the complete grinding circuit were analyzed for solids content and particle size distribution for two feed rates. Matrix models were used to represent the grinding units: rod mill and pebble mills. Parameters for these models were computed using a method developed by Mular(l). Classifier parameters were computed by the Powell search method(2) for the Plitt model (3) . The simulation program, which permits the computing of the size distributions in the circuit resulting from the changes in feed rate between the two measured values, assumes that a linear relationship exists between the corresponding parameter coefficients. The program uses an iteration method to bring the simulated grinding circuit to a steady-state material balance for any specified' feed rate between those measured. The program is, in addition, extremely fast and economic in computing time. The results show that the simulations are not everywhere consistent with practice. For example, higher feed rates on simulation predict finer products. These errors are shown to be attributable to anomalies in data gathering techniques. An improved sampling procedure for grinding-circuit data gathering is suggested for future simulations of this type. It is concluded that the

Jan 1, 1971

By R. T. Richins

Coeur d'Alene Mines Corporation (CDE) is a precious metals mining company. The company's three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE's gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

By R. Bhaskar

The control of quartz levels in the respirable dust requires an approach different from that used to control respirable coal dust. The unique physical properties of quartz have to be utilized when developing quartz dust control systems. Also, techniques that modify the surface properties of quartz dust so that conventional dust control measures are effective should be explored. For instance, the wetting characteristics of quartz can be modified so that the capture efficiency of the quartz dust can be improved. Foam sprays assist in modifying surface wetting characteristics. This paper summarizes the results of a study that was conducted in an operating mine to evaluate the effectiveness of a compressed air foam spray system installed under the boom of a continuous miner and directed so as to cover the pan and the gathering arm. The objectives of the study were to evaluate the effect of the foam underboom sprays on (1) the respirable dust concentration in the ambient air, (2) the quartz concentration in the respirable dust. The engineering design of the foam generation and delivery system is described in the paper, followed by a description of the mine and the dust sampling strategy. The data were analyzed to study the effect of foam on respirable dust and quartz concentrations at the miner cab, face return and the intake. The results of the data analyses and costs are presented in the paper.

Jan 1, 1991

By Avula Rajashekar Yadav, Sreenivasa Rao Islavath

Barrier pillars and gateroads play a vital role for the safe exploitation of coal from the panel in the longwall workings. The barrier pillars and gateroads are subjected to the front abutment and side abutment loads during the retreat of the panel. These structures may fail if the developed load on them is higher than their strength. The stability of the longwall structures such as barrier, gateroads and face is paramount in extracting the coal from the panel safely. For this, a deep longwall mine in India is chosen for the study using a 3D numerical modelling technique. In this paper, three critical conditions such as scenario 1 (no side goaved-out panel), scenario 2 (with side goaved-out panel) and scenario 3 (with two side goaved-out panels) are taken. For each scenario, five retreat distances such as 100, 125, 150, 175 and 200 m are considered for detailed investigation. The development of vertical displacement in gateroads, vertical stresses on barriers, vertical stress concentration factor, abutment zone and yield zone for longwall face are extracted and analyzed. Also, the safety factor of the barrier and longwall face is estimated considering the Hoek–Brown rock mass failure criterion. From the study, it is observed that the maximum vertical displacement of 121 mm in TG3 at scenario 3 for a retreat distance of 200 m and a minimum vertical displacement of 33 mm in TG2 for a retreat distance of 100 m at scenario 2. The development of vertical stress on the barrier is found to be between 8.78 and 13.40 MPa, and the safety factor of the barrier lies in between 1.56 and 1.80. The study also revealed that the yield zone at the longwall face lies within 2 to 3 m.

Dec 29, 2023

By Donald L. Bott

A computer model called the Quality Compliance Model was developed to optimize the mine planning and sequencing in area coal mining with respect to the limit on pounds of sulfur dioxide per million BTU imposed by regulations. The objective of the model is to maximize the amount of high sulfur coal mined from various benches while meeting the specified compl'ance standards. Given multiple seams and multiple benching operations, the mining sequence from each pit is simulated. The rate of mining is controlled such that the in-pit blending will maximize the usage of high sulfur coal and meet compliance standards. The compliant coal can be stockpiled for usage at a later date, or it can be disassociated. This calculation can be based on any given rate of production, i.e., from as small a unit as a unit train to as large as monthly or yearly production.

Jan 1, 1982

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicron range, and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicron range. Since dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using impactor-type size selector (diesel particulate matter impactor, DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) represent an alternative size selector for DPM sampling applications, with a major advantage being that, by design, they should not be susceptible to rapid aging. This paper presents results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device, and eventually a reduction of its effective particle cut size – though, when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions present for this study, effects of SCC aging were observed to be minimal by the end of the study period. INTRODUCTION Submicron particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, et al., 2000; Ristovski, et al., 2012). Diesel particulate matter (DPM) represents a major source of submicron particles in both public and occupational environments (Kittleson, 1998; Abdul-Khalek et al., 1998). Due to their work around large equipment in confined spaces, underground miners have some of the highest exposures to DPM (EPA, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as “soot”, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the NIOSH 5040 Standard Method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007 and Birch, 2016)."

Jan 1, 2018

By E. Fregeau-Wu

To recycle steelmaking slags for their iron, manganese, and lime contents, removal of the phosphorus-bearing dicalcium silicate and calcium phosphate is essential. Slow-cooling of slags was necessary to promote the sufficient grain growth to achieve liberation. In-situ grain size distribution determination showed that a high soaking temperature, a long soaking time, a very slow cooling rate, and the addition of fluorspar were shown to promote grain growth. High gradient magnetic separation on slow-cooled slags removed much of the dicalcium silicate. Liberation modelling was used to discuss the breakage and beneficiation characteristics of the slow-cooled slags.

Jan 1, 1992

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Chloride ions and their interactions with two organic smoothing additives – Cyquest® N-900 and HydroStar® 4208 – during copper electrodeposition were explored using cyclic voltammetry and electrochemical impedance spectroscopy. The results revealed that chloride ions, up to a concentration of 40 mg/L, depolarized the copper deposition reaction. A combination of chloride ions and Cyquest N-900 inhibited the depolarization reaction during copper electrodeposition. It is proposed that the chloride ions acted as bridging ligands between copper and Cyquest N-900. Addition of HydroStar at a concentration of 2.5 mg/L depolarized the copper deposition reaction when no chloride ions were present. This behavior did not change with the addition of chloride ions at the concentrations tested, indicating that chloride ions and the polysaccharide do not interact.IntroductionElectrowinning is a major production method used to obtain high-purity copper. In modern tankhouses, copper is electrodeposited onto stainless steel blanks and then stripped, washed and bundled for delivery. Significant improvements in the quality of electrowon copper have been made over the last few decades. Additives, temperature, current density, electrolyte concentrations and agitation are known to influence the quality of copper electrodeposits (Jenkins and Eamon, 1990).The influence of chloride and organic additives on copper electrodeposition has been the subject of considerable research. The addition of small quantities of chloride and organic additives has been recognized to significantly improve the properties of copper electrodeposits. These additives are critical in the prevention of dendrite growth and the production of smooth, dense cathode deposits.Chloride ions have been reported to catalyze the copper reduction reaction and assist in the production of uniform deposits (Lakshmanan et al., 1977; Sun and O’Keefe, 1992). Moreover, it is generally agreed that chloride ions depolarize the copper deposition process at low (several millimolar) chloride concentrations. This is because chloride ions catalyze the reduction of copper (II) ions to copper (I) ions (Cu2+ ? Cu+ + e-) in the rate-limiting step of this process (O’Keefe and Hurst, 1978; Ilgar and O’Keefe, 1997; Hebert, 2005; Shao, Pattanaik and Zangari, 2007)."

Jan 1, 2016

By G. A. Doyle

The White Pine Mine is the second-largest active underground copper mine in the United States, covering an area of approximately 13 square miles in the Upper Peninsula of Michigan. The mine operator intends to initiate in-stope solution mining by circulating a solution of mine water, sulfuric acid, and ferric iron through rubblized ore and recovering copper from solution. As planned, the solution would be retired in the mined-out stopes following completion of solution mining activities. Investigations into the fate of the retired solution mining fluid indicate that the solution, through time, will change from an acidic, metal-rich solution to a near-neutral, reducing solution containing much lower concentrations of metals. Investigations include reaction path modeling (EQ3/6) and laboratory and in-mine experiments. The combination of neutralization and reduction will result in precipitation of most metals, primarily as metallic sulfates, chlorides, and sulfides.

Jan 1, 1996

By Kanhaiya Mishra, Phanil. K. Mandal, S. K. Behera, P. S. Paul, Prashant Singh, C. N. Ghosh

The techno-economic and social benefits of cemented paste backfill (CPB) resulted in its wide acceptance by the mining industry. The Ordinary Portland Cement (OPC) remains the key binder but to diminish its economical constraints, suitability of alternate binders has been examined worldwide. The present study aimed to investigate the effect of partial replacement of OPC with fly ash on the CPB’s strength and to determine the most optimal mix to achieve the required strength (1 MPa at 28 days of curing) at the most cost-effective way using the Bayesian network (BN). The CPB mixes were prepared at 72 wt.% solid concentration with mill tailings (87–91%), OPC (6–13%), and fly ash (0–4%), and instantly after mixing, fresh (slump, bleeding, density) CPB properties were measured. The strength was tested at 7, 14, 28, and 56 days of curing and initially analysed through traditional model. The traditional models follow the aleatory principle and are considered not appropriate for geotechnical engineering. Hence, the BN model was developed and tested. The reliability of two classifiers in learning model structure was compared which gives Naïve Bayes as the highest reliable tool. The CPB’s strength is most sensitive to the OPC content. The most consistent mix(s) is mill tailings: 87–88%, OPC: 9–11%, fly ash: 1–4%. Adding fly ash at 89–91wt% mill tailings possesses high failure probability of the CPB. The collinearity test indicates that the fines percentage and chemical composition of CPB’s ingredients are highly correlated with its slump, bleeding, and strength development.

Jul 14, 2022

By G. Deschênes

Silver minerals are known to have slow leaching rates and low overall extraction and require a high concentration of cyanide and a long retention time to maximize leach extraction. Their response to cyanidation is considered mild to moderately refractory, largely due to complex mineralogical compositions. New research on improving the dissolution of silver minerals in cyanide was performed using high-purity minerals, as well as a high-grade ore sample from the Kupol property, owned 75% by Kinross Gold. The high-purity silver minerals studied in the leach investigations included acanthite, stephanite and pyrargyrite, which were also the predominant silver minerals in the Kupol ore sample. Dissolution of silver from acanthite produced only 37% extraction in 48 hours of leaching with 500 ppm NaCN. Analysis of the leached acanthite surface showed appreciable formation of polysulfide species, which can interfere with silver leaching. Adding lead nitrate into a pretreatment stage increased the acanthite silver extraction to 86.2%. No polysulfide species were formed with the addition of lead nitrate from the surface analysis. Cyanidation of stephanite and pyrargyrite produced very low dissolutions of silver, only 12.6% and 10.4%, respectively, in the absence of lead nitrate. Silver extraction from stephanite improved to 98% by adding lead nitrate directly to the leaching stage, whereas pyrargyrite required a pretreatment with lead nitrate to extract 83.2% Ag. With the addition of lead nitrate, the mineral surfaces had a PbO species and minor amounts of Pb(OH)2 and antimony was oxidized on the stephanite and pyrargyrite surfaces during leaching. There was a much greater concentration of Sb(V) on stephanite relative to pyrargyrite. Therefore, lead forms a redox couple on silver mineral grains and favors the oxidation of silver minerals. The high-grade Kupol sample assayed 22.6 g/t Au and 359.3 g/t Ag following treatment by gravity separation. Gold and silver extractions from the Kupol sample were 94.5% and 82.9%, respectively, using 500 ppm NaCN and 250 g/t lead nitrate. The findings to improve the extraction of silver from the ore sample with lead nitrate addition were congruent with those to improve the extraction of silver from the individual high purity minerals. Pretreatment did not, however, improve gold or silver extraction significantly with the ore sample.

Jan 1, 2011

By L. G. Martin

Early mining at Manhattan demonstrated that blasthole assays alone were insufficient to control the disposition of material. A program was began using controlled blasting, intense sampling and panning of crushed samples, fire assay checks, and geologic inspections to sort material in the pits. Statistical data confirms that the method provides effective control at minimal cost. This cost is easily offset by additional tonnage found in areas considered to be waste.

Jan 1, 1980

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold masses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By D. Stone, R. Pakalnis, B. Seymour

Most mines using backfill routinely carry out quality control (QC) testing of backfill mixes with unconfined compression test cylinders. This is true for paste operations, hydraulic fill operations, and cemented rockfill operations worldwide. However, a large number of mines simply do not prepare and test the backfill samples in a consistent manner and fail to properly analyze or interpret the test results. Conventional concrete test criteria are not applicable given the differences in the mix constituents and the fact that a large number of the backfill QC test cylinders typically fail to achieve the target strength. Standard industry practices are needed to improve the analysis and interpretation of QC test results and to provide a better means of determining if the backfill is achieving its intended target strength. This paper will attempt to lay the groundwork for standard industry practices and will address several key questions raised by operators, such as how laboratory test data compares to in-stope performance, and how many QC tests should fail before a red flag should be raised. INTRODUCTION Although paste backfill is widely used throughout the mining industry, cemented rockfill (CRF) remains as the backfill of choice in places like Nevada where very poor ground conditions mandate the use of underhand mining. The safety and stability of undercut entries beneath backfill is a function of the quality of the cemented fill, which is typically assured through routine quality control testing. In the absence of a backfill quality standard, most mines rely on concrete standards to design and interpret their backfill quality control programs. In the USA, these standards are developed and published by organizations such as the American Society of Testing and Materials (ASTM) and the American Concrete Institute (ACI). However, the application of these standards to cemented backfills can be very difficult owing to the high degree of variability in backfill mixes and the resulting variability in test results. To illustrate, the concrete industry standards denote that an acceptable (passing) test result occurs when the average strength of the duplicate test cylinders exceeds the target strength and no single test result deviates from the target strength by more than 10% (ACI 214R). Remedial measures must be taken if three consecutive tests fail. With mine backfills, it is safe to say that these criteria are rarely achievable. A further, more dramatic example is the accepted coefficient of variation for concrete QC cylinders. According to ACI 214R, the coefficient of variation (CV) should range from below 3% (excellent rating) to above 6% (poor rating). However, if this analysis method is applied to several backfill QC databases from operating mines, coefficients of variation are calculated on the order of 50%. Clearly, there is a need to develop better industry practices for assessing the quality of mine backfill and to assist mine operators with the interpretation of test results and the development of action plans in the event of undesired outcomes.

Jan 1, 2019

By Irwan Halim, Young Jin Park

A new tunnel lining was designed for rehabilitation of the existing unlined Weehawken Tunnel in New Jersey. Structural assessment using beam spring models was performed for the lining design as a drained structure at the invert with a waterproofing umbrella. Empirical Federal Highway Administration (FHWA) guideline was typically adopted for estimating hydrostatic pressure, which recommends full hydrostatic pressure at the crown and ten or twenty-five percent gradual reduction from the initial pressure toward the invert. Finite element seepage analyses were conducted for the actual conditions based on anticipated drainage behind the lining and impact on the structural design. Considerations will be provided on the existing guideline for estimating hydrostatic pressures.

Dec 1, 2022

By T. Lupek, M. Buxton, A. de Jong

"With regard to the EU funded project ‘Real-Time Mining’ a sensor-based acquisition, collection and transmission of data for the resource extraction process will be developed. The key concept promotes the change in paradigm from a discontinuous to a continuous process monitoring. Especially concerning material characterization, machine performance and underground positioning ‘Real-Time Mining’ will provide sensor solutions as well as the interfaces for integration, management and visualization of the collected data for a permanent updating process of the resource model with the aim of near real-time optimization of decisions. On the basis of ‘Real-Time Mining’-Output a permanent monitoring of costs can be performed as well in both, the installation and the production process of a mine. Due to the collected data in terms of machine performance connected with the underground positioning information added with personnel tracking and mine surveys a comprehensive overview of process performance is available. By evaluating those information in a specific manner costs per unit will arise for monitoring and possibly controlling actions. INTRODUCTION By having a look into the future of mineral extraction projects, a new challenge for the Ore Mining Industry will arise in the short and medium term. Due to the depletion of currently mined mineral reserves in addition to the persistently high demand of mineral raw materials, the extraction of complex reserves will be necessary. By characterizing such deposits as not constantly graded and geometrically varying, the extraction process, especially concerning the requirement of a minimized zero-value material handling, will become economically ineffective by utilizing the traditional mineral resource management methods. Regarding the state-of-the-art mineral resource management process along the mining value chain, an intermitted, discontinuous sequence of actions is applied (Figure 1). Recently data will be collected from drill hole cores. These rock samples are analyzed in a laboratory. Based on those analyses a resource model is created whereby unknown data between drill holes is interpolated. This resource model is the basis for all mine planning actions including the selection of the mining method, extraction sequencing and the prediction of the expected performance. With the start of the production, real conditions (concentrations of elements, hardness, stability, etc.) can be observed and measured. As the production process is running accordingly to the above described mine plan, the verification of the initial assumptions happens at the earliest after processing of the extracted material. Even if deviations between the predicted and the actual performance are now recognized, the execution of corrective actions is not possible anymore."

Jan 1, 2016