Search Documents

By Dennis C. Martin

Assessment of the potential for mining induced subsidence and determination of ultimate design requirements for a mining operation should be based on a number of assessment approaches. Although the rock mechanics engineer has a variety of limit equilibrium and numerical modeling tools available for assessment and prediction of subsidence effects, empirical approaches based on precedent experience provide a powerful tool for calibration/verification of analytical models and prediction of subsidence. Three separate analyses approaches have been applied to the assessment of potential subsidence for a proposed block caving mine in eastern Canada. The investigations have included an assessment of documented historical information from previous block cave mining at the site, deterministic analyses using limit equilibrium approaches to assess kinematically possible failure mechanisms, and three-dimensional numerical modeling techniques. Analyses results have been used and compared with precedent experience and documentation of subsidence behavior from previous mining to optimize the subsidence predictions for the proposed mine.

Jan 1, 1998

By Adam Bedell, Paul Derby, Brad Crenshaw

Modified contact grouting was introduced almost 15 years ago as a methodology combining traditional contact grouting and consolidation grouting to address groundwater infiltration into hard rock tunnels that utilize cast-in-place concrete as permanent tunnel support. This process has been used on additional tunnels (since initially presented) as a measure to mitigate both groundwater infiltration and exfiltration. During this time, self-sealing grouts have been developed and have been added to the process to further reduce groundwater infiltration that occurs through cracks and discontinuities within the concrete liner itself. This modification is presented and additional results from the grouting process are discussed.

Jun 13, 2021

By M. B. Mooiman

Cyanidation of gold and silver ores by conventional mining and milling techniques has been practiced for over a century. During the past decade, heap leaching has emerged as a viable process for treating certain gold and silver ores. (1) The rapid development of heap leaching for gold and silver ores is largely a result of lower capital and operating costs and faster start-up time than that offered by conventional mining and milling. In general, these features make heap leaching an ideal approach for exploiting either small or large low-grade disseminated deposits of gold and silver considered to be uneconomic by conventional methods. The development of heap leaching technology has evolved from the operations initiated in the western United States. The basic components of a typical heap leaching operation are depicted in Figure 1. Run-of-mine or crushed ore (usually 1 to 5 ppm gold) is delivered to specifically prepared impervious pads. Alkaline cyanide solution is applied to the surface of the heap and allowed to percolate through the heap (typically 10-30 ft high). Pregnant leach solution which drains from the heap is collected and stored in tanks of sufficient size or in collection reservoirs. Gold and silver are recovered from the pregnant solution and the barren solution is recirculated back to the heaps after reagent make-up.

Jan 1, 1983

By Samir Kumar Pal, Rajasekar Rathanasamy, Gobinath Velu Kaliyannan, Moganapriya Chinnasamy, Sathish Kumar Palaniappan

The research examines the performance of uncoated and coated tungsten carbide-cobalt rock cutting bits. It aims to optimize process variables (cutting speed, depth, coating material) considering multiple output responses (cutting forces, specific energy, wear rate, material removed, angle of reaction forces). The study uses a hybrid optimization technique combining Taguchi design, grey relational analysis, and fuzzy logic. The optimal parameter combination was found to be cutting speed: 200 mm/s, cutting depth: 6 mm, and titanium aluminum silicon nitride coating.

Apr 24, 2022

By George H. Davis

Much concern has been expressed recently as to whether water supplies will be sufficient to support accelerated energy development foreseen in operation Independence. Taking the Nation as a whole, sufficient water is available for energy growth, but locally, as in arid parts of the Colorado Basin, limited water supplies will dictate economies in water use and affect plant siting. As Young and Thompson1 point out with respect to electric power generation, the term "water requirements" is misleading, as demand for water for cooling is sensitive to price of water and thus is quite flexible rather than the inflexible or fixed level implied by the word "requirement." Much the same is true of other energy conversion systems. Water is used in many aspects of energy production including mining and reclamation of mined lands, on-site processing, transportation, refining, and conversion to other forms of energy. In the East, South, Midwest, and along the seacoasts, water supplies are generally adequate for energy industries; most water problems in those regions relate to pollution rather than supply. West of about the 100th meridian, however, runoff is generally less than potential diversions and energy industries must compete with alternative uses for the limited available water supplies. Water is especially short in areas of less than 10 inches mean annual rainfall where natural precipitation generally is insufficient for establishing vegetation without irrigation. Extraction. The principal categories of extraction comprise coal mining, oil and gas production, uranium mining, and oil shale mining.

Jan 1, 1974

By Jie Zhang, Xi Zhang, Yu Wang, Wei Zhao

The study proposes a novel reagent scheme where adding a small amount of citric acid (CA) significantly improves the depression effect of sodium silicate on calcite and fluorite. The flotation results suggest optimal concentrations for CA and sodium silicate, achieving nearly complete depression of the minerals. Theoretical analysis indicates that CA dissolves calcium ions on the mineral surface, enhancing the adsorption of sodium silicate and preventing collector adsorption.

Mar 27, 2022

By Richard L. Gordon

Coal supply analysis has since about 1973 become a major activity of many scholars and consulting firms. The present paper is an effort to explain in as nontechnical fashion as possible the state of the art and what implications, if any, the research has for those actually engaged in producing coal or regulating the industry. l The discussion stresses the coal supply side of the models and makes limited comments about other elements in the analysis. To orient the appraisal, it is desirable to recall the features of coal supply that an adequate model should capture. The first considerations are the locational aspects of the industry. Transportation costs can, in some cases, exceed the production costs of coal, and thus any adequate model must incorporate a treatment of the economics of transporting coal from one location to another. A second major issue is that of the heterogeneity of coal; models should treat as well as possible such key differences among coals as their Btu and sulfur content. Third, we recognize that, with given technology and labor, capital, and supply costs, an expansion of the supply of a given type of coal in a specific region will occur only if prices rise. This is the familiar proposition of textbook economics that supply is an increasing function of price. Finally, over time, changes in technology, input cost, and depletion interact to cause changes in the price of given amounts of coal. Economics represents the net effect of this process by a shift over time in the supply curve. During the 1950s and 1960s, the trend was to reduce the production costs of a given output; subsequently costs rose sharply.

Jan 1, 1977

By F. A. Renninger

The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Few individuals ever have occasion to purchase mineral aggregates for anything other than use for decorative shrubbery beds or walkways. They may, however, buy ready-mix concrete for a new patio, bituminous concrete for a new driveway, concrete blocks, or other building materials for a new room and never realize that the primary ingredients of their purchases are either direct or indirect products of the mineral aggregate industry. The average person driving past an operating crushed stone quarry or an active sand and gravel pit rarely realizes the economic impact the industry, represented by that operation, exercises on the general economy. He is not aware, nor does he really care, that elements of the modern comfortable environment to which he has grown accustomed rely to a great extent on the products of the crushed stone and sand and gravel industries Iron and steel, glass, cement, agriculture, and highway and building construction are but a few of the major industries to whom the products of the mineral aggregate industry are basic. Without these industries or without the stone, sand, and gravel basic to them, most of the major elements of our modern day civilization would be non-existent.

Jan 1, 1968

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013

Fundamental results obtained from research on the properties of the edge surfaces of kaolinite particles (~500 nm) are reported. Of particular significance was the development of the experimental protocol. Well-ordered kaolinite edge surfaces were prepared as an epoxy resin sandwich structure having layered kaolinite particles in the center of the epoxy resin sandwich. Images of the sectioned kaolinite edge surfaces were examined by atomic force microscopy (AFM), and the average thickness of kaolinite particles in this study was determined to be 38.3 nm ± 11.7 nm. Furthermore, the surface charge of the kaolinite edge surfaces was evaluated with a super sharp Si tip. The point of zero charge (PZC) of the kaolinite edge surface was determined to be below pH 4, in contrast to the traditional view that the edge surfaces of kaolinite particles may carry a positive charge at pH 4. This lower PZC of the kaolinite edge surface was attributed to the lack of isomorphous substitution in the silica tetrahedral layer when compared to the PZC for the muscovite edge surface. Our results are consistent with the particle aggregation and flotation behavior of kaolinite, and should provide the basis for improved flotation strategies leading to the efficient recovery and utilization of mineral and energy resources.

Feb 23, 2014

By Patrick J. Maessen, Bart H. M. Hendrix

"In the Netherlands, the Dutch Tunnel Standard has been developed for the execution of road tunnel projects. The Dutch Tunnel Standard is based on the Dutch Tunnel Law (WARVW) which sets the minimum safety standard for road tunnels in the Netherlands. Uniformity of tunnels and the uniform perception of a tunnel by its users leads to a higher safety level. Therefore, several items in the Dutch Tunnel Standard are specifically developed to ensure safety in emergency situations through the plane of human factors. Taking human factors into account is important in regular traffic situations, but in an emergency situation, this can be vital. In this paper, the development and contents of the Dutch Tunnel Standard are explained in the first part and in the second part, the systems related to human factors are described. DUTCH TUNNEL LAW AND THE NEED FOR THE DUTCH TUNNEL STANDARD In the 90’s of last century and the early 2000’s, several serious accidents occurred in tunnels in Europe. These accidents involved fire and led to many casualties. After these accidents, the European Union decided to change the regulations for tunnel safety, leading to the EU directive 2004/54/EG. The primary goal of this directive is, that casualties are minimized in case of a calamity in a tunnel (e.g. fire). In the Netherlands, the EU directive led to the development of the tunnel law and a tunnel regulation (in 2006) to prescribe the safety features required for a safe tunnel. The new Dutch tunnel law – cited in the Building Act – was meant to make tunnel design easier – but resulted at first in the opposite effect. Tunnel design in the Netherlands and design standards of Rijkswaterstaat Rijkswaterstaat – the executing organisation of the Dutch Ministry of Infrastructure and the Environment – is the owner of the tunnels in the Dutch national motorway network, thus owner of the majority of the road tunnels in the Netherlands. In the early years of tunnel building in the Dutch national highway network (approximately 1950 – 1970), Rijkswaterstaat was not only owner, but also designer of its own assets. Most Dutch tunnels are submersed tunnels, because these type of tunnels provide a cost-effective way to make river crossings. Another type of tunnel that is used, is a TBM tunnel. Because of the geological conditions in the Netherlands (merely clay/peat and sand), there are no NATM or drill-and-blast tunnels in the Netherlands. Since the last decades, land tunnels (covered roads) are becoming more common to provide for multiple use of surface space and to meet more modern environmental regulations as traffic increases near densely populated areas. Tunnel lengths in the Netherlands vary from 500 m to 1.5 km for river crossings up to 6 km for the Western Scheldt (bored) tunnel. The lengths of land tunnels vary from 500 m up to 3 km. With these increasing lengths, some safety topics and design topics arise, topics that were non-issues in the past, when tunnels were only used as river crossings."

Jan 1, 2016

By Ashley Woodward, S. Katharine Hammond, Mayela Padilla-Salas

This paper presents a scalable framework for worker safety assessments. The paper focuses on uranium mine reclamation in underserved communities, specifically Cove Chapter of the Navajo Nation. By integrating field observations, OSHA data analysis, systems mapping, and a hierarchical occupational health pyramid, this framework identifies site-specific hazards while addressing broader socio-cultural dynamics. The approach improves upon existing safety programs by suggesting actionable, locally sensitive solutions that prioritize higher-order controls such as hazard engineering interventions and administrative controls. This study contributes to enhanced worker safety, efficient environmental restoration, and engagement in marginalized communities with abandoned mine lands.

Feb 22, 2026

By Fun-Den Wang

In underground coal mines, three types of roof failure (2)*, tensile, local, and shear, occur in the development entries and in room-and-pillar extraction areas. Most of the tensile failures in the roof at the center of the mine opening as well as those local failures due to fracture or jointing can be controlled by roof bolts, trusses, and timbering. However, control of the shear failure at the sides of the roof (or the cutter-roof caving) has not been successful with ordinary roof control methods. The only effective method, when there is an indication of cutter-roof caving, is to use cribs, which are costly and make transportation, ventilation, and production difficult. Frequently, the operator allows the cutter roof to cave and then cleans it up rather than trying to stop it. This shear type of roof failure is often associated with large areas which may progressively involve several hundred feet of roof caving at one occurrence. At times, this shear failure occurs suddenly with little or no warning. This can result in buried equipment and great danger to the safety of personnel. This shear failure may be due to one or more of the following: high stress concentrations at the corner of the roof from (1) high horizontal to vertical load ratio, (2) orthotropic elastic properties of rock and coal, (3) greater stiffness of the immediate roof layer than of the secondary roof layer, (4) viscoelastic behavior of rock and coal, and (5) geometry and material properties of the geologic setting. Removing or reducing the high stress concentration should improve the roof stability. The structural analyses of models of two typical

Jan 1, 1972

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

You have been involved with research activities in froth flotation and size reduction. What do you think the future holds for these technologies? Froth flotation and size reduction are essential processing steps common to almost all current mineral-processing operations. The most significant recent advances in both of these technologies have been in the increased size of equipment and in some alternative machine designs, such as the column cells and the high-pressure roller mills. I believe that the next major area of improvement in size reduction will be at least partially driven by an improved awareness of controlling the conditions that influence the efficiency of particle breakage. This would include factors such as water-chemistry influences, the influence of fines from classification, chemical grinding additives and better rheology control. In froth flotation, significant changes are currently taking place in the plant use of frothers. Also, there will be an increasing number of new collector chemistries for certain types of flotation, such as with oxide minerals, oxidized mineral recovery in sulfide systems and improved selectivity with certain sulfide mineral systems. You have been active in implementing new engineering technology in industry. What do you think will be the technological future of mineral processing? Being involved in the invention and industrial implementation of new technology has been one of the most positive experiences of my career. I also have had the unique experience of working in the chemical and petroleum industries as well as in mineral processing. In my opinion, the future of mineral processing will be an exciting, wonderful work area in which to be involved. The development of new technology in minerals processing offers a special challenge compared, for example, to that of chemistry or chemical engineering. In successful industrial innovation involving minerals, having a sound theory is not enough. Instead, what is required is a valid blend of a good idea, meaningful laboratory characterization and, most key, the experience necessary to adjust the plant in such a way to incorporate the idea. The complexity of engineering systems that contain solids, liquids and gases, as well as highly variable natural mineral properties, means that nothing new comes easily. In some cases, it has been difficult to explain how processes practiced in industry for decades actually work, in terms of physical and chemical fundamentals. On the other hand, when a new idea is successfully implemented, the economic and professional returns can be very rewarding. I know of no more challenging field of engineering than minerals processing. What is your view of the future of the minerals industry in general? The need for minerals, metals and coal will be with us for decades to come. In many aspects, the minerals industry became global much earlier than some of the other industrial sectors that are currently experiencing globalization. I believe that fair international competition is beneficial to the users of minerals, metals and coals and to those involved in producing such materials. The key word here for a global economy to work is "fair." So the various playing fields involved such as finance, profit return, regulation and labor should be relatively level for all the players involved. Competition is an amazing driving force for innovation. This has been true in the minerals industry during the last few decades. The mining industry is producing more at less cost per unit than ever before in our history. I anticipate that this trend will continue as long as the global political situation remains relatively stable.

Jan 1, 1997

By Shakuntala Tudu, Indrajit Paul, Surajit Sinha, Pulibandla Basaveswara Rao, Shaik Mahaboob Basha, Srinivas Dwarapudi

The iron and steel manufacturing sector directly accounts for 7–9% of global CO2 emissions. Raw material preparation, such as iron ore sintering, pelletizing, and cock making, is the major CO2 emitter. As climate change becomes a bigger concern, steel manufacturers need to lower CO2 emissions without hindering efficiency or increasing costs. In recent years, the percentage of iron ore pellets in blast furnaces has increased due to its uniform size, good reducibility, and high tumbler index. Pelletizing is energy-intensive and emits considerable CO2. Around 20% of CO2 emissions during pellet making come from fluxes. In the present work, the authors established a novel CO2- free flux called wollastonite (CaO.SiO2) for sustainable palletization. Pellets with varying percentages of wollastonite (0–6%) are prepared and tested for chemical, physical, and metallurgical properties. Image analysis through an optical microscope is carried out to quantify the phases of fired pellets. SEM–EDS is performed to evaluate the chemical composition of the melt and slag phases. The results showed that the reducibility index (RI) and swelling index (SI) of pellets decreased with an increase in wollastonite dosage. Pellet strength increases with an increase in wollastonite addition up to 1.2% CaO (2.27% wollastonite), and a decrease in strength is observed thereafter. The increase in strength is attributed to the increase in slag bonds. The decrease in strength beyond 1.2% CaO is mainly because of an increase in low melting eutectics and more magnetite content. Pellets with 2.27% wollastonite to get 1.2% CaO showed good physical and metallurgical properties.

Mar 4, 2024

By T. A. Gray

There are several potential large-volume uses for coal ash in mining-related applications that could be environmentally and economically beneficial to mining companies. Actual usage, however, may be constrained by regulations or by perceptions of coal ash and the potential uses. To identify currently allowed uses and to assess constraints to coal ash use in the eastern coal fields, questionnaires were sent to state coal mining agencies to determine their policies on coal ash utilization and to mining companies to solicit their viewpoints on coal ash utilization. Identifying and understanding the constraints will allow for the development of a coordinated and consistent approach to remove or reduce these constraints and possibly allow for increased utilization of coal ash by the mining industry. This paper summarizes the findings of our investigation.

Jan 1, 1995

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990

By E. J. Karges

The use of pulverized coal for generating power and performing industrial processes has made an important contribution to our industrial economy during the past half century. Actually, the burning of coal in powdered form is a subject that has held the attention of engineers for a century or longer. Its widespread use, however, is comparatively recent, As early as 1866 patents were granted to Messrs. Whelpley and Storer for a method of feeding pulverized coal into a furnace as an auxiliary to the grate fuel. In the many tests made during the subsequent years with various kinds of apparatus, the experimenters were handicapped in not getting the coal fine enough to obtain complete combustion and to prevent excessive formation of slag.

Jan 1, 1965

"Mine ventilation is in every underground mine a crucial process to ensure mine safety as well as acceptable working conditions. On the other hand is also a major cost factor depending on air requirement and air resistance. Due to the fact that the special layout of mines develop over time, ventilation systems change as well. This may result in complex systems which are suffering severe problems and low efficiency. With attention to the mine safety and costs, ventilation systems have to be controlled repeatedly and optimized continuously to fit changing conditions. The project “Improvement of ventilation systems in narrow vein mines” has been commenced with measuring and data collection in the Bogala Mine, Sri Lanka. This over 150 year’s old graphite mine consists of about 20 levels. The resulting ventilation system is highly complex and suffers problems like high temperatures and humidity as well as a mixing of fresh and used air on lower levels. To solve these problems and to optimize the system the complete ventilation system had been measured on-site first. The gained data have been used for simulations to develop and select an optimal and cost efficient solution. OBJECTIVE As an important process in mining ventilation is a major cost factor and can determine the economic feasibility of a mine. Due to the production mine layouts develop over time and mines increase in size and depth while the ventilation system becomes more complex and may suffer severe problems and inefficiency. Therefore mine ventilation systems have to be controlled and optimized regarding the general requirement of mine safety and health of the miners as well as the costs. Depending on the deposit type, depth, mining method, climate and as well corresponding laws and regulations the possible solutions are varying strongly. The work carried out paid special attention to the improvement of ventilation in narrow vein mines in tropical climate, in this case the graphite mine “Bogala” in Sri Lanka, South Asia."

Jan 1, 2015