Search Documents

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains (CAC) on roof bolting machines have been proven, through laboratory and field investigations, to protect miners from respirable dust, preventing dust overexposures. Another desired application is to develop a CAC that is mounted in the compartment of a shuttle car to protect the operator from dust. The challenges faced with this design include mine ventilation rates in tandem with the shuttle car tram speeds, causing cab airspeeds that may exceed 600 fpm, as found in this study of a central Appalachian underground coal mine. Prior research and laboratory testing indicate that successfully protecting a miner in high air velocities is difficult to achieve because the clean air from the CAC is unable to penetrate through the high velocity mine air and make it to the breathing zone of the operator. During this investigation by researchers from the National Institute for Occupational Safety and Health (NIOSH), dust concentrations of the shuttle car operator were measured. Also, air velocities experienced by the operator were measured using a recording vane anemometer. Results from the survey indicate that the highest exposure to respirable dust (2.22 mg/m3) occurred when the shuttle car was loading at the continuous miner, where there was an average airspeed of 157 fpm. While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 203 fpm. This study indicates that a CAC system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, since the majority of the operator’s dust exposure occurs in air velocities less than 200 fpm. INTRODUCTION NIOSH has issued a contract (#200-2015-63485) with Marshall University and J.H. Fletcher & Co. (Salem et al., 2016) to develop a canopy air curtain (CAC) for coal mine shuttle cars. The proposed design maintains a similar design to the roof bolter CAC by providing filtered air via a blower over the operator. The plenum, which will provide the uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a CAC is ventilation airflow perpendicular to the plenum airflow [Engel et al. 1987]. This ventilation airflow, if the velocity is significantly high, can shear the downward flow from the plenum. The shear caused by the ventilating airflow can reduce the effectiveness of the CAC by either disrupting the downward flow or allowing contaminated mine air into the CAC zone of protection."

Jan 1, 2018

By H. Kinilakodi, R. L. Grayson

In 2010, the U.S. Mine Safety and Health Administration (MSHA) began holding hearings on a new coal mine respirable dust rule, which proposed a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the “hot spots” where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines’ compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, average mining height and selected “hot spot” counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications for the need for better dust control methods.

Jan 1, 2012

By F. Dingwu

The latest technology and novel equipments in kaolin processing industry in China are described in this paper. Some typical experimental results are presented, which include laboratory-, pilot-or commercial-scale tests. The characteristics of kaolin processing technology are summarized, and the developing trends are indicated.

Jan 1, 1995

By Ralph W. M. Lai

The liquid membrane separation process was first patented in 1968 for separating hydrocarbons.(1-4) This stimulated many researchers to join in the area of separating organic compounds. l Since then, its applications have been extended to the removal of contaminants from waste water,(12-33) encapsulation of enzymes and/or microorganisms for reaction and/or separation, (24-28) oxygenation of blood (artificial lung),(19) removal of toxins from blood (artificial kidney)(26,20) and metal extraction.(31-63) This paper discusses the possible process schemes for using liquid membranes to separate and concentrate copper ion from its acidic leaching solution.

Jan 1, 1982

By Samuel Rigert, Marco Bettelini

"INTRODUCTION AND OBJECTIVES Long rail tunnels require in most cases powerful mechanical ventilations. Besides requirements related to normal operation and maintenance, operational safety always requires a high level of smoke management. Identifying the optimum ventilation concept is essential for achieving proper performance and safety while keeping investment and operational cost at a reasonable level. For the purpose of the present paper, long tunnels have a length of typically 20 km or more. This is related to the European classification of trains (TSI 1303/2014), where the maximum distance from the portals to a firefighting point and between firefighting points is limited to 20 km (only category B passenger rolling stock allowed) or 5 km (general case). From TSI 1303/2014 it can be concluded, that tunnels over 20 km require in any case emergency stations with complex mechanical ventilations. Based on the experience arising from a number of recent projects in the European area, including in particular Gotthard (GBT), Lötschberg, Lyon-Tourin (LTF), Brenner (BBT) and Gibraltar, safety-relevant issues related to the ventilation of long railways tunnels are reviewed in this paper. Amberg Engineering is directly involved in these challenging design tasks and can provide first-hand experience and know-how. As a particular highlight, special attention is devoted to the longest tunnel worldwide, the 57 km long Gotthard Base Tunnel, which will be commissioned in 2016. THE GOTTHARD BASE TUNNEL Overview The Gotthard Base Tunnel will be commissioned in 2016 (official inauguration on the 1st of June and beginning of regular operation on the 11th of December) and will be the worldwide longest tunnel. Its complex and powerful ventilation system is very representative for many other long tunnels and is used as reference in this paper. Therefore, a few key characteristics of the Gotthard Base Tunnel and its ventilation system will be described in some detail in this initial chapter. The Gotthard Base Tunnel (GBT) consists of two single-track tunnel tubes with connecting galleries every 312 meters. Two so-called multi-functional stations (MFS), located at roughly 1/3 and 2/3 of the tunnel length, host the key equipment for normal and for emergency operation. At these locations, double crossovers allow trains to switch from one tunnel tube to the other. An emergency station is located in each multifunctional station, allowing trains to stop in case of emergency. The general layout of the GBT is presented in Figure 1."

Jan 1, 2016

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical assessment of orebodies in the mining industry typically relies on bench-scale or lab-based characterization techniques. In this study, we investigate drone- and tripod-based field hyperspectral imaging as a potential addition to the geometallurgy toolkit in multiple applications. This pilot study tests hyperspectral imaging for largescale mineral mapping in and around the active Lisbon Valley copper mine, including natural exposures, previously producing U-V mines, highwalls, dumps, and leaching sites. Tests include different (supervised and unsupervised) mineral data classification methods, varying mineral spectral reference libraries, comparison with ground-truth geological and spectroscopic mapping and sampling, and integration with LiDAR data. The results show that hyperspectral scans can produce spatially registered maps of the distribution of different spectrally active mineral types over dumps, highwalls, leach pads, and natural outcrops. Clays, other phyllosilicates, carbonates, and sulfates showed up particularly well. The sensor was also able to distinguish dry from lixiviant-saturated areas and map different clay types on the leach pads, and shows promise for differentiating types and health of vegetation. These results suggest that hyperspectral imaging, if coupled with robust ground-truthing, can be a useful complement to existing geometallurgical techniques in the mining industry, such as geological mapping, blast hole sampling and automated mineralogy identifications, and handheld spectrometry. In particular, hyperspectral imaging has promise for mapping the distribution of acid-consuming minerals; mapping the distribution of swelling, sliming, and heap-blinding clays; and pinpointing problem areas on heap leach pad surfaces.

Feb 10, 2021

By T. McCallum, C. Cooper, B. Hutzler

"In copper solvent extraction, managing the quality of the organic phase is a key parameter to ensure optimal physical and metallurgical performance in the plant. Increased throughput as a result of declining ore grades coupled with advances in plant design and practice, resulting in reduced organic losses, has pushed the limits of the status quo with respect to organic quality. Clay treatment of plant and recovered organic at the optimal dosage is critical in maintaining quality, however, achieving the optimal dosage through existing filtration capacity and practice can be difficult. Cytec has developed a process aid that increases efficiency of existing filtration equipment that has been successfully implemented at two commercial SX operations. ACORGA® CB1000 enables higher dosages of clay while allowing for more efficient use of existing filtration capacity. This study analyzes results from commercial trials and demonstrates that improved organic quality and clarity is achievable through optimization of current treatment practices. INTRODUCTION Decreasing ore grades have prompted copper solvent extraction operations to raise PLS flow rates, increasing plant throughput to maintain production1. The ability to process higher flow rates through existing mixer-settlers historically came at the expense of increased entrainments2. However, advances in mixer-settler design, practices and improvements in organic recovery processes have enabled operations to maintain, and in some cases reduce organic losses while achieving higher flow rates through existing equipment. Based on the increased demand on the SX equipment and reduced losses (or more efficient recovery) maintenance of the circuit organic quality through efficient clay treatment is now more important than ever. This paper discusses common industry practices and related issues in organic clay treatment, and presents benefits achieved in commercial operations through the use of ACORGA® CB1000 Clay Binder. IMPROVEMENTS IN DESIGN AND PLANT PRACTICE Mixer-settler design has improved since the first commercial copper SX operation in the late 1960s. Advanced designs in mixer, settler, and settler internals have contributed to reductions in entrainments. For example, improved impeller designs have been reported to decrease organic in aqueous entrainment from the ‘old designs’ of 50-200 ppm3 to as low as 4 – 10 ppm confirmed via diluent and reagent consumptions . Similarly, operations are reporting a 20-50% decrease in reagent consumption when compared to the original design criteria3. Operations have optimized settler internals to increase coalescence and have improved settler operating practices which have been shown to reduce entrainments7. Comparison of the SX world operating data from 1999 and 2007 shows reductions in organic entrainment losses with increases in flow rates."

Jan 1, 2015

By A. K. Bakshi

Slurry rheology affects autogenous grinding performance by changing the rock's breakage characteristics. In this study pilot scale batch autogenous grinding was carried out to observe the effect of viscosity on the breakage characteristics of the rocks (the media), and on the overall specific energy consumption. Clay/fines content, and temperature of the initial charge, were varied to alter the viscosity of the slurry. Results showed that at higher slurry viscosity, rocks became more difficult to break, resulting in an overall increase in the specific energy consumption of the mill. Also, it was observed that viscosity had a significant effect on the amount of critical size material present in the grinding circuit, where the critical size material is the material which is too large to be effectively ground in the mill, and too fine to act as grinding media.

Jan 1, 1996

By H. Salamanca

The electric operation and design features of the 11.000 H.P. variable speed SAG mill gearless drive is presented. The function of the frequency converter, control system drive and lubrication systems are described. An analysis of the harmonic characteristic in the Supply System and Motor is presented, and the dynamic development of the stator current, speed and the magnetic flux in the start-up process of the drive is evaluated. Besides, the most important aspects in the commissioning and maintenance of the drive are analyzed.

Jan 1, 1991

By D. D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a cost-effective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Feb 23, 2014

By P. Sander, M. Spiegl, J. Reilly, A. Van Droogenbroeck

Although the outdated idea of calculating risk as the deterministic product of its likelihood and impact is not entirely a thing of the past, a multitude of organizations have adopted the usage of probabilistic methods for risk analysis, as they better reflect the inherent uncertainty of cost and risk estimates with ranges. But are these advancements sufficient in a complex environment such as tunnelling projects, where inadequate modelling of cost and risk can result in estimate discrepancies that run into millions of dollars? This paper explores two advanced probabilistic modelling techniques for tunnelling projects. The first one demonstrates how the cost and schedule uncertainty related to changes in excavation and support classes can be modelled with correlated variables. The second example models the risk related to explosive ordnance clearance on construction sites using a probabilistic event tree.

Dec 1, 2022

By Carlton M. Ray, William P. Levy, Thomas Lindberg

"The District of Columbia Water and Sewer Authority (DC Water) is implementing its $2.6 billion DC Clean Rivers Project to reduce combined sewer overflows to the District’s receiving waterbodies and mitigate chronic sewer flooding in District neighborhoods. The First Street Tunnel project is a major component of the DC Clean Rivers Project, designed to mitigate sewer flooding and basement backups in the District’s historic and densely populated Bloomingdale neighborhood. Bloomingdale has been historically affected by sewer flooding and was severely impacted by four storms in the summer of 2012 that caused significant damage to homes, the environment and public property. As a result, DC Water accelerated the design and construction of the First Street Tunnel in order to mitigate the effect storms have on the undersized sewers serving the neighborhood. The infrastructure designed to mitigate flooding, including the tunnel, are located within the highly urbanized neighborhood – with some structures being less than ten feet from residents front door steps. The success of a large public works project of this magnitude and in this unique location depends on a well informed and supportive public. With the local community impacted by flooding but concerned about heavy construction impacts, this paper details the components of a successful public outreach plan and lessons learned throughout the design and construction process. Early identification of community mitigation, working cooperatively with stakeholders and frequent dissemination of accurate information required the project team to establish a culture of problem solving collaboration with the community. BACKGROUND Chronic Flooding in the Northeast Boundary Sewershed The Northeast Boundary sewershed, in which the Bloomingdale neighborhood is located, is served primarily by a combined sewer system and has a long history of chronic flooding problems during moderate to severe storm events. The sewer system that serves the Northeast Boundary drainage area was constructed by the Federal Government in the late 1800's when developed areas of the District terminated at what is now Florida Avenue. Since construction of the system, population within the sewershed area has grown at an exponential rate. In meeting the growing needs of the population, the District experienced development that transformed previously low-density rural areas into new communities. Impervious areas have increased drastically since the sewer system was constructed and consequently, the existing sewer system does not have the capacity to convey storms with return frequencies beyond the 2-year storm without flooding. As a result of the capacity limitations, many of the low-lying areas have become chronic flooding areas due to the surcharging of sewers."

Jan 1, 2016

By A. J. Kwitowski

Teleoperation is a technology that can provide significant health and safety improvements in mining, by relocating machine operators hundreds of meters away from the face area. The U. S. Bureau of Mines (USBM) has recently developed a teleoperation system for continuous mining and haulage equipment. This system features near-real-time closed-loop control. A prototype system was developed and demonstrated on the surface. This system could be used in thin-seam applications down to 914 mm. Details are provided on the developed teleoperation system, results of testing, and expected, future applications of this technology for improved safety.

Jan 1, 1994

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not co-precipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Jan 1, 2011

By J. L. Huiatt

The U.S. Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 5 percent K. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgSO4.2.7H20) and schoenite (K2SO4MgSO4.6H20), were conditioned in a saturated brine solution, thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular weight fatty acid. Continuous small-scale pilot plant testing indicated that 80 percent of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 11 percent K.

Jan 1, 1975

By B. R. Arvidson

Rare-earth elements have some unique properties that are used in many common applications, such as TV screens and lighters. In the 1970's, rare-earths began to be used in a new generation of magnetic materials that have very unique characteristics. Not only were these stronger in the sense of attraction force between a magnet and mild steel (high induction, B), the coercivity (He) is extremely high. This property makes the magnetization of the magnet body composed of a rare-earth element alloy very stable, i.e., it cannot easily be demagnetized.

Jan 1, 1998

By David G. Kidd

The principles of Ore Sorting in general and photometric sorting in particular are discussed with detailed reference to the Model 16 machine. The operating principles and design of the Model 16 are discussed and a case study presented to demonstrate the use of sorters to process an industrial mineral. In addition, an economic study is presented, to highlight the benefits of ore sorting, by evaluating the increased revenue that can be achieved using an ore sorter to process a particular ore body.

Jan 1, 1983

By W. Petruk

Mineral liberations that would be obtained by grinding an ore to a specific size can be predicted by analyzing unbroken ore pieces, and mineral liberations in ground ores and mill products can be determined directly by image analysis. Predictions of mineral liberations are made by measuring size distributions and textures of mineral grains by image analysis, and using liberation models. Ground ores and mill products are analyzed to determine the proportion of mineral that is liberated, and the data are used to evaluate mineral behaviour during mineral beneficiation. The liberation data for minerals in a suite of mill products from a circuit are processed by a materials balancing technique to calculate recoveries of minerals in different types of particles throughout the circuit. The liberation-materials balance data define mineral recoveries; define the behaviour of an ore in a concentrator, pilot plant or bench test; and indicate whether recovery improvements are possible and/or feasible.

Jan 1, 1991

By J. Duran

Mining at Newmont Mining?s Phoenix?s Mine is currently done by surface operation in the Fortitude and Bonanza pits at a combined rate of approximately 100 kt/d (110,000 stpd). A portion of the orebodies targeted by these pits was mined previously by underground mining methods, dating back to the mid-to late-1800s. Most of the underground workings (voids) are located in the west central area of the Bonanza pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This article presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

By C. S. Harman, C. A. Enright, J. F. Brune

"The mining environment presents challenging and complex situations for the application of medical care. The combination of remote locations, difficult access and longer response times may create an increase in morbidity and mortality in the event of serious accidents. The U.S Mine Safety and Health Administration (MSHA) has only minimal requirements of first aid training for mine workers. For mine rescue team members, MSHA requires medical training at the Emergency Medical Responder (EMR) level, as only prescribed by mine rescue contest rules. This paper examines, based on mine accident statistical information, whether a higher level of medical training, for example at the Emergency Medical Technician (EMT) or at the Advanced Life Support (ALS) level can better address injuries most commonly disabling or leading to the death of miners in the United States. BACKGROUND Prehospital emergency medical care for the sick and injured has evolved considerably from first inception. Ambulances used to be staffed by persons with little training and equipment and prehospital care was focused largely on the rapid transport of the injured person to a hospital and. The modern prehospital care model was initially developed in military applications, where medics were responsible for some treatment on the battlefield and rapid transport to the care of a physician. In 1965, the National Academy of Sciences and National Research Council Committees on Trauma and Shock published Accidental Death and Disability: The Neglected Disease of Modern Society (National Research Council Committees on Trauma and Shock, 1966). This white paper laid out the consequences of the insufficiency of the Emergency Medical System (EMS) in the United States at that time. According to this paper, in 1965, 107,000 people were killed from accidental injury, with another 400,000 injured with permanent disability. The authors estimated that approximately 50% of ambulance services were provided by local morticians that were not capable of rendering advanced life support. The paper states that, based on experiences in the Vietnam war, seriously wounded soldiers had a better chance of survival in the battle field compared to traffic accident victims with similar traumatic injuries because the military was capable of providing first aid and efficient transportation to emergency care facilities. The white paper states that death rates from battle injuries declined significantly from 8% in World War I to 2% in Vietnam. The publication of this white paper is credited for the broad evolution and rapid advance of the civilian EMS system after 1965. It eventually lead to the creation of the National Highway Transportation Safety Administration (NHTSA) National Standard Curricula (NSC) for emergency medical care in 1985. Training, and therefore required skill and knowledge for prehospital emergency care has continued to grow to reach the current standard."

Jan 1, 2016