Search Documents

By Leandro Augusto Viana Teixeira, Angela Avelar, Ruberlan Gomes Silva, Virginia S. T. Ciminelli, Daniel Majuste

Rare earth elements are essential for modern life products and green technologies. Recent supply constraints have boosted the development of rare earth projects after the price peak of 2011. The feasibility of a project depends on the definition of a processing route, which in turn depends primarily on the rare earth mineral, with monazite and bastnaesite representing the two most relevant minerals. Monazite-type ores usually contain high acid consumption impurities, such as iron, aluminum, calcium, magnesium, and phosphates, and may also contain prohibitive levels of radioactive thorium in its composition. This work presents a thermodynamic analysis of a monazite system and discusses the fundamentals of a selective process route for rare earth extraction from monazite ores with high iron content. This process involves sulfation by means of concentrated sulfuric acid and roasting at a high temperature. The route yields high rare earth extraction with low iron and thorium extractions and low acid consumption. Rare earth extractions as high as 80% were achieved, while iron and thorium extractions were lower than 1%, and acid consumption was lower than 0.34 kg of sulfuric acid per kg of ore. The operational window was compared to the one predicted by thermodynamic modeling, with 700 °C representing the optimal roasting temperature

By H. Huang, R. N. Gow

"The reactivity of an enargite mineral electrode was investigated spectroelectrochemically under conditions typically found in alkaline sulfide leach solutions, with pH 11-13 and Na2S additions of 50 and 250 gL-1. A bulk enargite electrode was cycled between 0 and -1,000 mV for each set of solution conditions. Raman spectroscopy was used to determine and compare surface formations against species in mass-balanced EH-pH diagrams generated using STABCAL. Previously, it was determined that arsenic could be selectively leached under alkaline conditions at an average solution potential of -300mV, across the pH range 11-13. Operating under such conditions allowed for the selective leaching of arsenic with elemental sulfur formation. From several of the voltammograms obtained during this current testing, the formation of elemental sulfur appeared at increasingly reducing conditions with increasing sulfide concentration. At high concentrations, copper started to dissolve, possibly as a bisulfide complex, reducing the selectivity of the leach, unlike previous studies. However, the presence of the higher sulfide concentration is also anticipated to prevent passivation by consuming any surface formation of elemental sulfur. This study provides insight into the operating parameters of alkaline sulfide leaching in regards to the selectivity of arsenic leaching, as well as guidance for control of reagents and solution potential and, of course, the need for water treatment afterwards.IntroductionEnvironmental limitations on the pyrometallurgical processing of arsenic-bearing concentrates have forced operations to consider other solutions. Attempts to hydrometallurgically process enargite (Cu3AsS4) fall into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under basic conditions. The authors believe that the selective leaching of arsenic is more amenable because it produces a solid copper phase, preferably chalcocite (Cu2S) or covellite (CuS) that could then be processed using conventional methods already in place in the copper and gold industries. Potential leaching methods include alkaline sulfide leaching (Achimovicovica et al., 1999; Anderson and Twidwell, 2008a,b; Tongamp et al., 2009 and 2010), hypochlorite leaching (Vinals et al., 2003; Curreli et al., 2005; Mihaljovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and acid leaching (Gow et al., 2014b) with or without fine grinding to mechanically activate the enargite surface and increase normally slow leach reaction kinetics (Achimovicova et al., 1999; Balaz et al., 2000; Balaz and Achimovicova, 2006). In this study, the reactivity of enargite under alkaline sulfide leach conditions was examined."

Jan 1, 2015

By C. J. Bise

Virtual Reality (VR) is a concept in which the human experience of perceiving and interacting with a computer-modeled environment is achieved through the use of sensors and effectors. It is an advanced fonn of computer graphics where the images are generated based upon where the user looks and how the user moves. As personal-computer-based (PC-based) instruction gains acceptance as an innovative approach to providing safety training, VR offers the capability of providing a multisensory, rather than merely a multimedia, mode of presentation. VR has been effectively used by the military for training tank commanders and by hospitals for training surgeons. However, these applications have been limited to small numbers of highly skilled participants. The purpose of this paper is to examine VR's potential for enhancing the hazard awareness of larger numbers of individuals in a broad-based approach to mine safety training, such as new-miner, annual-refresher, and independent-contractor training.

Jan 1, 1996

By Russell G. Shomperlen

Grinding mills in excess of 5 meter diameter and 3500 kilowatts per mesh are putting new demands on big gears. This paper returns to the basics of ring gear design beginning with the fundamental power formulas specified by AGMA. Specific emphasis is given to those elements in the rating equations which require closer attention as gear diameters and transmitted power increase. Strict process control in the manufacture of the gear blank is also stressed. Finally, the writer offers a guide to proper installation, lubrication and maintenance.

Jan 1, 1981

By Lei Zhang, Zhibo Ma, Pingye Guo

The mechanical behavior of hard roofs often leads to significant deformation and strong mine seismicity in gob-side entry retaining (GER) of the longwall mining, affecting the mining safety and efficiency of coal mines. Field investigations indicate that the failure process of the retained entry by hard roofs can be divided into three stages. In this paper, theoretical analysis and numerical simulations are first used to evaluate the damage process of the retained entry under the hard roof. The results show that the instability of the retained entry in the conventional GER method results from the combined static-dynamic loads (in stage II and stage III) from the hard roof. Then, an innovative method, through fracturing roofs to maintain entry (FRME), based on GER with the hard roof is introduced to solve this problem. In this method, the roof of the mining area is pre-fractured, and when the coal seam is mined, the direct hard roof will collapse along the fractured surface due to its deadweight and mining pressure. The hard roof control effect on the static and dynamic loads, taking into account the innovative method, is verified with simulations and theoretical analyses. The results are compared with those of the conventional GER method. Furthermore, based on the numerical simulation study of dynamic responses, it is found that compared to the GER method, the dynamic response of the retained entry using the innovative method is more moderate and more conducive to the stability of the entry. Field application also validated the effectiveness of the innovative method to control the mechanical behavior of the “massive sudden collapse” of the hard roof.

Aug 14, 2023

By W. J. Dolinar

The U.S. Bureau of Mines implemented the Fe2+ /Fe3+-SO2 anode reaction in a Cu electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/m2 (24 A/ft2) and 40 'C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb) compared to conventional electrowinning. Acid misting was completely eliminated, and SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1995

By R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corporation's Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about -502 without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1971

By Andrew Trusiak

Brunswick Mining, employing approximately 1600 employees, is located 40 km south of the city of Bathurst in north eastern New Brunswick. The mine has operated as two lead-zinc operations - the underground mine(No.12) and the open pit mine (No.6). The open pit orebody is presently being' mined by underground methods. It is expected that the No.12 mine will furnish the entire ore supply by the end of 1981. The flotation practice prior to 1971 has been described by Neumann and Schnarr(1) and by Erskine (2). More recently, the current flotation practice has been described by McTavish(3) and deals with some major circuit modifications between 1972 and 1978. The period 1978 to 1980 has seen the completion of. a major flotation cell replacement and expansion program for the No.6 concentrator, and the implementation of computer control in the No. 12 CuPb and Zn flotation circuits.

Jan 1, 1981

By Jim Salley, Mohammad Saleem, Indra Banerjee, Kevin Sapp

"On underground construction projects, effective Quality Management is essential for ensuring facility durability, life cycle performance and low maintainability. Furthermore, follow on contracts also rely on an effective quality management system for interface congruency. An effective Quality Management System (QMS) is also essential in mitigating risks and meeting schedule and budget performance objectives. For the past 15 years Central Puget Sound Regional Transit Authority’s Link Light Rail extension has successfully completed over 10 miles of twin bore tunneling and associated underground features including cross passages, deep sump structures and shafts. After the completion of each segment, lessons learned have successfully been implemented to improve the quality of delivered projects. This paper presents the Sound Transit QMS with regard to a number of project elements of tunnel construction projects, with specific focus on quality performance of slurry wall construction, TBM tunnel excavation assessment, segment production and segmental lining installation, and other associated construction features. A collaborated total QMS will be presented in this paper that will serve as a guide for successful implementation of Quality Assurance and Quality Control processes. INTRODUCTION Implementation of a robust Quality Management System reduces defects, errors and omissions, identifies and addresses nonconformance in a timely manner and increases stakeholder confidence in the project. In fact and effective QMS helps ensure that optimal project outcomes are realized both in terms of project delivery and life cycle performance. The two key components of QMS are quality control and quality assurance. Quality Control (QC) is the procedure implemented to achieve a certain level of quality and ensure that products, processes and services meet specific requirements. Quality Assurance (QA) activities are carried out to evaluate the effectiveness of the quality control measures and ensure that the QC process is working. A team obligation that recognizes that quality is built into every aspect of a project is the basic concept of a successful QMS."

Jan 1, 2016

By Ron Drake

The Anderson Dam Tunnel Project is a high-priority, urgent project under construction by the Santa Clara Valley Water District in California. The project will provide a new low-level outlet for the Anderson Reservoir enabling the seismic retrofit of the Anderson Dam as mandated by the Federal Energy Regulatory Commission. This paper describes planning for construction of the tunnel through the dam’s right abutment crossing several faults in challenging and variable soft and hard ground conditions. The construction methods include SEM, hard rock drill and blast techniques, and a mechanized 8-foot (2.5 m) diameter microtunneled lake tap.

Dec 1, 2022

By R. G. Sinclair, E. Sangine, S. M. Fortier, J. Brainard, K. Stone

"The U.S. Geological Survey and Natural Resources Canada conducted a study on the net import reliance of each North American country, and the impact of North American trade on the net import reliance of 12 nonfuel mineral commodities that are associated with advanced technology products: cadmium, cobalt, gallium, germanium, graphite, indium, lithium, nickel, rare earth elements, selenium, silver and tellurium. The combined results for North America, using 2014 data, showed greatly reduced net import reliance for nearly all of the commodities evaluated, which is largely the result of pooling the resources of production and recovery in Canada and Mexico of materials that are consumed in the United States. This study highlights the mitigation of potential supply risk for critical materials that results from trade within the North American trade bloc. IntroductionMultiple metrics and definitions exist for what constitutes a critical material, but there is broad acknowledgment that a mineral commodity may be considered critical if, among other factors, its production is geographically concentrated, if it has few or no substitutes, or if the country of origin is politically unstable. Numerous governmental and independent researchers have proposed methods of investigating criticality, with differing priorities such as economic resilience or strategic military supplies (European Commission, 2014; Graedel et al., 2015; U.S. National Science and Technology Council Subcommittee on Critical and Strategic Mineral Supply Chains, 2016). While criticality really depends on who is asking the question, and despite the differing priorities, there are several commodities that are commonly found to be of concern. In particular, some critical or potentially critical materials are used increasingly in advanced technologies, or they have complicated supply chains because they are coproduced or are produced in controlled markets.Commodities for which imports are required to satisfy domestic demand are those for which the importing country is net import reliant. Net import reliance (NIR) in this study is calculated as the amount of imported material, including changes in stockpiles, minus exports and is expressed as a percentage of domestic consumption:"

Jan 7, 2018

By Rameshwar Sah, Somasekhar Pitchika, Akhil Singh, Seenivasan Rajiah, C. B. Dayanand, G. Balachandran

In the sintering of iron ores, the partial substitution of anthracite coal for coke breeze has been considered to be an effective way of reducing emissions and improvement in sintering properties. In the present study, the combustion characteristics of the anthracite coal and coke breeze were investigated and its influence on product sinter quality and sinter flue gases is being monitored. Pot trials are carried out with different coke breeze ratios, 0%, 40%, 50%, 60%, and 100%. It is found that as the percentage of anthracite coal is increased from 0 to 100%, the sintering time decreased from 24 to 20 min, and the productivity increased from 2.25 to 2.60 t/h/m2. Up to 60% anthracite coal substitution Tumbler index (+ 6.3 mm%), Product yield (+ 5 mm%), and fines generation (− 5 mm%) is found 62.29%, 85.17%, and 15.33%; moreover, hematite ( Fe2O3), magnetite ( Fe3O4), calcium ferrite phases ( CaFe2O4, CaFe3O5), and Silico ferrite of calcium and aluminum (SFCA) are major mineral phases found during microstructural analysis of product sinter. Keywords Sintering · Anthracite coal · Combustion rate · Productivity

Jun 2, 2022

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"PROJECT OVERVIEWThe Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million inhabitants. The project was constructed by a joint venture of four South American contractors (“the JV”), and consisted of the following key components:• Treatment Plant: A 16 hectare area was cleared for the construction of a treatment plant to purify 900,000 m3/day of raw water from the Paraná River and distribute it to the surrounding communities.• Bored Tunnel: Nearly 15 km of 3.6 m inner diameter tunnel, ranging from 18 to 22 m below grade, was bored with two EPB tunnel boring machines to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions: Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access & Ventilation Shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of: one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (Intake and Treatment Plant, respectively), and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installed afterwards. Access Shaft 3, the intermediate shaft located between the launch shaft and the treatment plant, experienced persistent leaks during initial excavation attempts."

Jan 1, 2016

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990

By M. Misra

The dispersion of oily collector has significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. However, such dispersion and reagent addition techniques are invariably inadequate and non-selective. A new collector utilization technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This new technique involves atomization of the collector into the gas stream. Under these circumstances an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the gas phase (continuous with respect to oil) and the gas phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de-facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and most significantly increases the flotation rate of ultrafine coal. Furthermore, atomization of collector/frother combinations yielded improved flotation yields and maintained near uniform froth levels which is a desirable feature in coal flotation. In addition to flotation experiments, microscopic examinations of the attachment of oil-coated bubbles at a coal surface were conducted by attachment-time and contact-angle measurements. The oil coated bubbles attach at significantly faster rates and with a higher contact angle than do oil free bubbles.

Jan 1, 1987

By S. G. Ozkan

Boron minerals of economic importance are primarily colemanite, tincal, and ulexite. Turkey and the United States are the leading producers of boron minerals and compounds. Other production includes datolite in Russia and synthetic colemanite in Chile. This paper will discuss various types of chemical and physical treatments of boron ores to produce the marketable minerals and compounds that are consumed in commercial products.

Jan 1, 1995

By R. Merwin, S. Hoff, A. Ellsworth, M. Zhao, X. Jiang

The choice of mill linings in comminution circuits is critical as it affects grinding efficiency, overall cost, and product quality. As a consequence, a variety of liners have been developed over the years in an effort to increase wear resistance, improve grinding efficiency, and reduce energy consumption. One particular type of metal magnetic lining (MML) was developed in China seventeen years ago and has since been installed in over 400 applications throughout the Chinese mining industry. Most recently, one set of magnetic mill liners was brought to the US for installation into a secondary ball mill used for the grinding of iron ore. Protection of the mill is provided through the magnetic attraction and retainment of worn media, ball chips, and other various magnetic particles to the mill wall. This greatly improves the wear resistance and overall life of the liner. The installation and performance data for the magnetic mill liners in a US iron ore concentrator are presented in this paper.

Jan 1, 2007

By Halter L. Gould

Since the turn of the century there has been a marked increase in population, industrial and economic growth, and in energy requirements in the United States. During this time our energy needs have been met largely by natural gas and petroleum, but as our reserves of these materials are depleted, we are going to depend more and more on our large reserves of coal. The mining of coal for electrical power production has increased at a rapid rate during the past decade. Over half the coal produced in the United States in 1971 came from mines utilizing surface mining operations (Paone, et al, 1974). Surface mining is expected to increase as the rising cost of oil places more demand on coal for energy. About 57 percent of the coal reserves in the United States lie in the area west of the 100th meridian. About one-quarter of this can be mined by current surface methods. This would involve the disturbance of approximately 1.5 million acres (600,000 hectares). By the year 2000, projections indicate disturbance of about 200,000 acres, or 300 square miles, in the West. Mined areas receiving more than 250 mm of annual precipitation can usually be revegetated without irrigation if the spoils are properly shaped, the surface layer consists of suitable plant growth media, and proven techniques in rehabilitating disturbed rangeland are applied. Areas receiving less than 250 mm of annual rainfall or with high evapotranspiration rates pose a more difficult problem. Revegetation of these areas can probably be accomplished only with major inputs of water and good management (National Academy of Science, 1974).

Jan 1, 1978

By P. M. Keyser

Column flotation continues to make inroads into applications traditionally dominated by mechanical flotation cells. For example, columns are becoming more visible as rougher flotation devices. At Royal Mountain King Mine in California, two 2.9 m (9.5 ft) diameter columns are used for rougher flotation of carbon from a gold ore (Orlich et al, 1992). In addition, work performed at BRGM in France demonstrated the superiority of column flotation over mechanical flotation with respect to design of new plants (Morizot et al, 1991). With the mounting evidence, columns can succeed in any flotation application. The primary reasons for this acceptance of columns are a general improvement in design, scale-up and operation as well as improvements in sparger design and performance. With these advances, the full benefits of column flotation can be realized. The benefits of properly designed, aerated and operated flotation columns include: ? Lower Capital Costs ? Reduced Operating Costs ? Fewer Processing Stages ? Improved Metallurgical Performance

Jan 1, 1993

By D. J. A. Chambers, J. M. Wempen, K. D. Koper, M. K. McCarter, K. L. Pankow

"The EarthScope Transportable Array (TA) of broadband seismometers (www.usarray.org) was deployed across southwest Wyoming from November 2007 through May 2009. During this time period the Array Network Facility (ANF, anf.ucsd.edu) detected and located a total of six seismic events near the trona-mining district. This lack of seismicity is atypical compared to coal mines employing similar mining methods. In this study, eighteen months of continuous seismic data from several nearby TA stations are reexamined using conventional and correlation-based methods to detect seismic events. Waveform cluster analysis and epicentral locations are used to discriminate between mining induced seismicity (MIS) and seismic energy generated from surface blasts at nearby coal mines. The locations and magnitudes of the 143 newly detected MIS events are compared to regional subsidence as measured by Differential Interferometric Synthetic Aperture Radar (DInSAR). INTRODUCTION An abundance of natural resources and a favorable political climate have made southwest Wyoming home to multiple large mining operations. Among these operations are five underground trona mines located approximately 50 km west of Rock Springs, Wyoming. The trona mines employ room and pillar, longwall, and solution mining methods over an area roughly 900 km2, and produce a sizable portion of the world’s soda ash (Brown 1995). Historically, in the Rock Springs mining district, several relatively large magnitude seismic events have occurred. These events are thought to have been related to mining activity and have caused notable subsidence (Case 1997). The largest event in the region recorded by seismometers, ML 5.1, has been confirmed as the 1995 Solvay Trona Mine collapse (Pechmann et al. 1995). In addition, blasting at surface coal mines near Rock Springs produces significant amounts of seismicity; approximately 50% of all daytime seismic events in the Mountain time zone from 2007 to 2009 locate near an active surface mine in this region (Astiz et al. 2014). Much of the current research related to surface subsidence and induced seismicity focuses on wastewater impoundment (Ellsworth 2013) and hydraulic fracturing. The observable seismicity in geological injection environments is widely variable and McGarr (2014) has argued that, in such environments, the maximum amount of seismic energy that can be released is proportional to the injected volumes. Like injection environments, in extraction (mining) environments seismicity is highly variable depending on many geological and operational variables (Boltz et al. 2012; Carnec and Delacourt 2000; Fritschen 2010; Iannacchione et al. 2005; Sen 2013) and does not always correlate well spatially with subsidence, a surface expression of extraction at depth."

Jan 1, 2015