Search Documents

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By E. J. Donovan, O&apos

The use of Dynamic Analysis techniques in the design of conveyor systems is extremely limited. The most frequent use of the technique is in large and expensive systems where the emphasis is on insurance against failure caused by catastrophic tension waves. This paper sets out to illustrate a much wider range of applications where dynamic analysis has been successfully employed. The examples chosen deal with identification and correction of dynamic low tension problems, the variability in take-up movement as other system parameters change, the requirement for proper tuning of starting controls and finally the absolute necessity for a complete understanding of the entire system when specifying brakes for critical applications. The intent of the paper is to get designers to view a conveyor as a system of interacting flexible components rather than as a single rigid body.

Jan 1, 1993

By S. Ragab

The objective of flotation models is to predict the recovery rate of minerals from a flotation cell. In this paper a CFD?based flotation models is presented. The model uses first order rate equation, and the collision frequency is estimated using Abrahamson [1] model with input from CFD two-phase simulations. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) are determined by the two-phase hydrodynamic simulations. Knowing these parameters throughout the machine is essential in understanding the effectiveness of different components (rotor, stator or disperser, jets) on the flotation efficiency. Not only the average pulp recovery rate can be estimated but also the regions of high/low recovery rate can be identified. The CFD-based flotation model presented here can be used to determine the dependence of recovery rate constant at any locality within the pulp on particle diameter, particle specific gravity, contact angle, and surface tension.

Jan 1, 2012

By F. Heivilin

Little did I know, in 1977, that when the A. P. Green Refractories Raw Material Manager showed me 5-6 burlap bags with samples of calcined high alumina bauxite in their testing lab that this was the start of China moving to be the number one user and producer of calcined refractory bauxite. According to Ted Dickson in his August 2008 Industrial Minerals article China produced about 4 million tons of calcined bauxite in 2007 using 2 million tons themselves. They imposed an export limitation of 970,000 tons in 2007 and 940,000 tons in 2008. A 10% growth will take up the difference between exports and production in 4 years. Two of these years are gone. It will take only 4 more years to eliminate the export quota in home use. Then they will be importing unless they increase production. Guyana was exporting over a half million tons in 1975 and sold less than 70,000 tons in 2002. Basai Metals Group bought Guyana?s deposits and is rose to 250,000 tons in 2007 and expects to produce 280,000 tons in 2008. PRICES According to the USGS Prices dropped from $172/per ton for Guyana calcines in 1980 just after the start of Chinese production to $122 in 1985. Guyana prices averaged around $120/ton from 1985 to 2005. China?s price dropped as low as $45/ton in 1995 undercutting Guyana and making it virtually impossible for anyone to get into the market. The price suddenly escalated to $550/ton FOB China in the summer of 2008 when China actually cut its exports in half. The price dropped in the fall as orders dropped. This is a four to five fold price increase. Is this a shortage of bauxite or a monopoly? Australia dropped out of the market in 2008 and Surinam, controlled by Alcoa, is not participating right now. Will these two come back in to make up the difference? Will the price hold up so they can make a profit? [ ] The low prices have undoubtedly affected the prices of the 60 and 79% alumina bauxite which can hold down the quantity of 80% plus calcined refractory needed in the world market. China is starting to upgrade lower quality bauxite up to 90% alumina. With high prices kaolin alteration to high alumina comes into play. The calcined bauxite is also used for proponents, Brown fused alumina, and abrasive grades which compete with Refractories. These and the tightness of supplies needed for metallurgical will hold prices up. TONNAGE China is the number one supplier and consumer of high alumina calcined bauxite in the world. Basai Metals Group Guyana (BMGG) is owned and controlled by Basai Minerals Group of China. This appears to be the second largest supplier. Australia has dropped production and Brazil is just starting to expand. It appears China is going to replace some of exports caused by the Export License 940,000 ton maximum in 2008 by raising Guyana?s (BMGG) production of calcined refractory grade bauxite. Companies exceeded restriction in 2007. Fines have been imposed for 2008. In August 2008 they appear on line to meet the 2008 quota. After August prices have dropped off as orders dropped due to the recession. Guyana was the largest producer in 1975 with 769,000 tons which decreased to less than 79,000 tons in 2002. The U. S. is a small part of the world production. I have used the United States charts to represent world imports because I have little data on what other countries import and pay FOB for their bauxite. China started exporting calcined 80% plus refractory bauxite to the United States in 1979 with 24,000 tons. By 1985 they were the number one importer with 169,000 tons. Guyana who had been number one in shipments to the United States gradually decreased to 36,000 tons in 2006. Guyana has been purchased by China BMGG and will increase there production to over 200,000 tons in 2009. Australia shut down production in 2008 and Surinam has elected to not send any Calcined bauxite to the United States. Imports to the United States from 1978 to present are as follows: [ ] Refractories are important because they affect 96% of the GNP. During the cold war we had stockpiles of 80% refractory grade bauxite

Jan 1, 2009

By R. H. Clarke

"INTRODUCTION Characterization of waste rock is frequently an oversight in mine planning which can contribute to significant delay in permitting and ultimately development. Thorough waste rock characterization is now a prerequisite to developing operating and closure plans acceptable to regulators and the public. BACKGROUND A long history of mine development has placed virtually all focus on the economic extraction and beneficiation of ore materials, while waste rock characterization and management received substantially less attention and consideration. Inadequate waste rock characterization has contributed to planning and management practices that are having unintended and unforeseen impacts to surface and groundwater, and in some cases lead to significant long term closure liability. In response, the regulatory community has developed guidelines for performing waste rock characterization during the pre- mine permitting process that in some cases seem onerous (BLM, 2013). Additionally, where a project proponent has not met these guidelines or results have been deemed “inadequate”, the Nevada Division of Environmental Protection and Bureau of Land Management (regulatory agencies) will only issue operating permits with rigid management practices to address the uncertainty, including requirements for lining waste rock facilities. WASTE ROCK CHARACTERIZATION FOR NEVADA PROJECTS Newmont Mining Corporation (Newmont) operations in Nevada approaches waste rock characterization like ore characterization, as it requires a similar investment of time, funding and attention to detail in order to pass public and regulatory scrutiny. Newmont follows a tiered approach to characterization that creates three over-lapping data sets representing an “escalation” in analysis at each tier, an approach that has thus far gained regulatory approval. “Tier 1” waste rock characterization for most Newmont projects begins with exploration drilling which follows internal standards and procedures. 20-foot composite samples are prepared from all drilling and analyzed for multiple trace elements using inductively coupled plasma mass spectrometry (ICP-MS) methods and for acid-base characterization using method ASTM-E1915. If the exploration program is successful and further resource or reserve development is recommended, the Tier 1 data are used to prepare a Waste Rock Characterization Plan (Plan) that will be presented to regulatory agencies as a part of baseline project characterization."

Jan 1, 2015

By P. Hickey, J. Spenceley, T. J. DeMull

Development of the Batu Hijau Project was successfully completed in the fourth quarter of 1999 with the final handover and start-up of ore processing facilities. The development project had started more than three years earlier, in August 1996, when the Owner, PT. Newmont Nusa Tenggara (PTNNT), awarded an EPC contract to Fluor Daniel (FD) for design and construction of the project including: copper concentrator, port, power plant, town site, and infrastructure. PTNNT managed the development of the mine and procurement of mine equipment with its own forces. Bringing the Batu Hijau copper deposit into production was the largest mining project ever undertaken. Development of Batu Hijau was a complex project involving the work of tens of thousands of people in all parts of the world to complete engineering, manufacture and deliver equipment, supply materials, and build the plant. The ore deposit is located on the tropical island of Sumbawa in a remote and undeveloped section of Indonesia. The location and environment presented challenges for all phases and aspects of the project. To meet the challenges, the project team combined good planning and teamwork to best utilize the resources available. This approach assured continuity of personnel through construction to operations and minimized cost, resulting in completion of the project ahead of schedule and under budget.

Jan 1, 2001

By A. M. Anthony, A. Y. Atta, S. S. Magaji, U. Abubakar-Zaria

There are two major gold recovery methods: the hydrometallurgical technique, which employs cyanide solutions, and amalgamation method, which involves mercury (Hg). These methods present considerable health, safety, and environmental concerns. Past applications of alpha-cyclodextrin (α-CD) on gold scraps show that α-CD is not only inexpensive, but is also environmentally friendly. This research work used α-CD to recover gold from gold ores instead of gold scraps. The gold ore was sourced from Shanono gold deposit site Kano State,Nigeria. The gold ore was characterized by fire assay (FA) for the precious metal. The concentrate was digested with aqua regia (AR) for 24 h. Modified AR, where hydrochloric acid was replaced with hydrobromic acid, was used for the gold digestion due to the good match in molecular recognition between gold bromide ion (AuBr)− and α- CD in a second sphere coordination complex. The digestate was characterized using atomic absorption spectroscopy (AAS). Gold recovery using this technique is pH sensitive, and five pH values (2.0, 3.6, 4.0, 5.4, and 6.0) were investigated. FA analysis showed the Shanono gold ore deposit contains an average of 4.71 ppm of gold, AAS analysis showed highest gold recovery of 69% at pH 4.0, which is lower than recoveries from the metal scraps. This could be due to the presence of other gangue minerals closely associated with the ore. However, gold recovery using α-CD on Shanono gold ore has shown to have a higher yield of 69% compared to 35.5% yield obtainable by Artisan Small Scale Miners using mercury.

May 5, 2020

By R. S. Conti, M. R. Krump, C. P. Lazzara Ph. D., R. L. Derick, L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, CO, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward-sloping (20%) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward-sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used, due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results.

Jan 1, 2010

By Douglas B. Silver

"Editor’s note: Douglas B. Silver, Portfolio Manager, Orion Resource Partners, was the keynote speaker at the 2017 SME Annual Conference & Expo in Denver, CO on Feb. 19, 2017. He also gave the keynote address to the SME Annual Conference in 2008. The following is his 2017 keynote address with a few of the slides that were presented. The full speech is available on YouTube https://www.youtube. com/watch?v=uF0qwGJIX3UIn 2008, I had the privilege of giving SME’s keynote address. At that time the financial markets were on the verge of collapse and my presentation described the issues. Unfortunately I was correct, and global markets went into a steep nosedive, creating the largest economic downturn since the Great Depression.In hindsight, there were plenty of signs that this was coming. The Supercycle had created massive new wealth. This wealth was largely invested in the United States due to the country’s political stability and credit worthiness. In 2004, the large investment banks convinced the U.S. Securities Exchange Commission (SEC) to allow them to triple their borrowing leverage ratios. This made the banks more vulnerable to market volatility. The banks then lent money to NINJAS - people with no income, no job and no assets. Even worse was the fact that these unqualified home owners used adjusted-rate mortgages (ARMs) which they, of course, intended to refinance prior to interest rates rising. These mortgages were then bundled up by the banks and sold to investors as “safe” investment products. The money flowed into these products because the rating agencies gave these instruments high marks. These same agencies earned their fees from the very same banks seeking high ratings. (No conflict there). Private debt exploded and peaked out in 2008.These mortgage products were sold in an unregulated shadow banking system and the ARMs came due. Toxic mortgage default rates skyrocketed and the mortgage-backed securities collapsed in value. This house of cards had a negative feedback loop that accelerated the market crash and resulted in more than $1.5 trillion being lost in the securitization sector, a 47 percent decline in the Dow Jones Industrial Average, foreclosure rates skyrocketing and housing prices collapsing. The financial markets were in a nosedive."

Jan 8, 2017

By R. G. Church

Belle Ayr Mine was established in 1972 as the first large surface coal mine in the Powder River Basin of Wyoming. During the mid-1980s, it was eventually out-distanced in productivity by newer mines, and management recognized that the mine must recapitalize its major mining equipment and enhance its workforce flexibility in order to be competitive in the deteriorating market situation. Therefore, state-of-the-art haulage and loading equipment was placed into service, and a 12-hour rotating shift and a technician-based workforce was implemented. Belle Ayr Mine is located 29 km (18 miles) southeast of Gillette, Wyoming, in Campbell County (Figure 1). The mine is a part of AMAX Coal West, Inc., and with its sister mine, Eagle Butte, located 8 km (5 miles) north of Gillette, is a major contributor to the overall coal production of AMAX Coal Industries, Inc., headquartered in Houston, Texas. This paper addresses mine planning, recapitalization initiatives, and innovative workforce changes which propelled this large, surface coal mine to the forefront of productivity in the ever tightening low sulphur coal market.

Jan 1, 1994

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By Shilpa S. Haramkar, Bhaskar N. Thorat, Sachin V. Jadhav

The filtration of phosphogypsum is a ubiquitous step in the manufacturing of phosphoric acid. It is highly desired to achieve the minimum concentration of P2O5 in the phosphogypsum cake. This work is aimed at addressing P2O5 losses in phosphogypsum (PG) along with the recovery of P2O5 from slurry by using constant pressure filtration at 1 bar pressure. Laboratory tests were carried out in the phosphoric acid production plant situated in Paradeep, India. Recycled water source near acid plant (i.e., pond water) was used for cake washing to reduce the burden on fresh water stock. The findings indicated that pressure filtration offered the most effective P2O5 recovery (nearly 93.48%). The moisture was reduced to 14–16%, and watersoluble P2O5 in the gypsum cake was found to be negligible. A narrow particle size distribution was observed, which offered effective filterability with average cake resistance of 2.38 × 1010 m/kg, indicating a moderately separable cake.

Aug 23, 2023

By G. Bulut, Ü. Yenial

"The use of recycled water in flotation has significant effects on flotation and selectivity because the recycled water contains many dissolved compounds and ions that alter the chemistry of the system. In this study, the effects of calcium, magnesium and sulfate, which are abundant components in recycled water, were investigated on galena, sphalerite and pyrite flotation using pure minerals and a complex sulfide ore by conducting bench-scale flotation, microflotation and zeta potential measurements. The bench-scale flotation tests indicated that higher recoveries of galena and sphalerite are obtained when water is recycled, due to higher concentrations of ions in recycled water. However, there was a critical ion concentration for galena recovery. The microflotation tests showed that galena recoveries at different pHs in recycled water are lower than in tap and distilled water. Pure sphalerite recoveries improved in recycled water in the bench-scale test with ore. Pure pyrite was depressed with recycled water as well. Zeta potentials became less negative with increased calcium and magnesium ion concentrations due to their adsorptions, and the presence of sulfate ions was seen to increase the negative charges of sphalerite and pyrite, conversely for galena. IntroductionWater is among the most important elements for mining and mineral processing. The distance to water sources is one of the major factors for mine site selection. The mining and mineral processing sector needs and consumes large quantities of water. In Chile in 2014, the copper mining sector alone consumed 12.7 m3/s fresh water for 1.189 tons of ore processing, and recycled 74 percent of the consumed water (Chilean Copper Commission, 2015). A plant that does not reuse or recycle any water will require 1.9 to 3.0 m3 of water per ton of ore processed (Gunson et al., 2012). Many stages of mineral processing, such as grinding, gravity concentration, dense medium separation, wet magnetic separation, flotation and hydrometallurgical operations, use large volumes of water (Schumann, Levay and Ametov, 2009).In mineral processing plants, the process water is recycled from the tailings dams, thickener overflows, and dewatering and filtration units. Wet concentration processes can require large quantities of water. Flotation, the most common process, typically takes place at 25 to 35 percent solids by mass. Most flotation plants practice at least some water reuse and recycled. Modern mines and mineral processing operations generally aim for zero water release (Levay, Smart and Skinner, 2001). In most cases, water quality has been found to affect flotation performance, and this interaction remains under investigation."

Jan 1, 2016

By P. Zhu

The leaching behavior of copper powders recovered from waste printed circuit boards (WPCBs) was investigated using electrogenerated chlorine and aeration in a sulfuric acid solution with added NaCl and CuSO4. Various parameters were studied to understand the mechanism of the copper leaching. When the current density increased from 0 to 0.1 A/cm2, the temperature from 30 to 60° C, agitation speed from 100 to 400 rpm, and the size ranged from below 75 to 150 µm, the leaching ratios of copper powders increased. The leaching kinetics were analyzed using a shrinking core model: 1-(1-X)1/3 = kt, and the leaching process was chemically controlled with an activation energy of 14.7 kJ/mol due to Cl- ion catalysis. The ratios of [Cu+]/[Cu2+] at various temperatures (30, 40, 50, 60 and 70° C) showed a periodic variation with the increasing of the leaching time. The redox potentials of the leaching solution and copper leaching ratios in different conditions were measured. The result indicates that dissolved oxygen achieved the dissolution of coppers and electrogenerated chlorine can promote the dissolution of copper powders and improve the reaction rate of kinetics in the presence of oxygen.

The classical slope analysis and a statistical technique were used in order to determine the iron complexes formed in the organic phase during the extraction of Fe(III) from Fe-Ni-Co sulfate solutions with Di-(2-ethylhexyl) phosphoric acid (D2EHPA) in kerosene. Equilibrium constants for the extraction based on these complexes were also calculated. The complexes determined were of the general form (Fe(OH)3-nRn?sHR)x' where n varied between 1 and 2.5 and s between 0 and 3, and both were found to be decreasing as the iron loading in the organic phase increased. Values of 1,2 and 3 were generally found for x, indicating that the complexes were monomers, dimers and trimers.

Jan 1, 1988

By John M. Hird

Texas Gulf Sulphur Company's Lee Creek Mine has opened a major phosphate mining district in the Central Coastal Plains of North Carolina (Fig. 1). The ore deposit as it is now known was roughly outlined in 1961 by a Texas Gulf geologist using wire line exploration methods. Slightly uraniferous phosphate materials were detected by a slim-hole gamma ray probe run in numerous farmers' water wells penetrating the formations. A follow-up-core drilling pro- gram determined the economic ore limits to lie in the south central section of Beaufort County beneath 70 feet to 120 feet of unconsolidated sediments. The 50,000 acre deposit is known to contain over two billion tons of phosphate ore amenable to strip mining methods. A part of the deposit underlies several thousand acres of the Pamlico River estuary. The 90 million dollar capital investment plant built by Texas Gulf during 1965-66 included a strip mining operation using a 72-yard walking dragline, a three million product ton per year flotation concentrator, four fluid bed calciners, a sulphuric acid plant (acid for captive use), a phosphoric acid plant, and three solid fertilizer material plants. Shipment to domestic markets is by rail and truck and to over- seas markets by barge to a transshipment terminal at Morehead City, North Carolina. Early mining investigations were conclusive first that the phosphate ore could economically be recovered only by dry strip mining methods, and second that artesian ground waters in the formation (Castle Hayne limestone) underlying the ore would have to be controlled. This report will relate the application of ground water hydrology in depressurizing the Castle Hayne aquifer to facilitate dry strip mining at depths 130 feet below sea level at the Lee Creek Mine.

Jan 1, 1970

By David W. Wisecarver

The U.S. Bureau of Mines, in cooperation with U.S. Borax and Chemical Corporation and the Kennecott Copper Corporation, has investigated the use of the microseismic method to evaluate the stability of large, open-pit slope walls. The method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. This report briefly describes the three different types of microseismic apparatus, the procedures, and the results of microseismic investigations in the slope walls of the Boron Mine near Boron, California, and the Rimbley, Liberty, and Tripp-Veteran open-pit mines near Ely, Nevada. Microsesimic noise rates in stable inactive mining areas are between 0 and 10 noises/ hour; the rates in stable active mining areas are between 10 and 50 noises/hour; and the rate in unstable areas is as high as 2500 noises/ hour. High microseismic noise rates in the Liberty Pit correlate with the time of nearby earthquakes, indicating that the earthquakes affected the slope wall. The results provide evidence that the microseismic tech¬nique is applicable to large pit walls, and that the wide band, wide range microseismic equipment appears to be suitable for open-pit investigations.

Jan 1, 1969

By E. Yigit

Hydrometallurgical production of zinc from concentrates is generally carried out by H2SO4 leaching. For the smooth operation of this process, some harmful components must be removed from the leach solution before the electrolysis stage; MgO is one of these compounds. Zinc concentrate samples from the Mount Isa mines were used in leaching tests. Leaching tests with an aqueous solution of H2SO4 and SO2 gas were carried out at various temperatures, pH levels and leaching durations. While duration and the pH value of the solution were effective parameters in H2SO4 leaching, temperature and pH were more effective in SO2 leaching for the removal of MgCO3 and CaCO3. Removal of MgCO3 and CaCO3 was generally achieved at low pH values. The results show that SO2 gas can be a good alternative to sulfuric acid in the leaching of MgCO3 and CaCO3

Jan 1, 2010

By W. D. Blackburn

If there is a single key to managing a mineral extraction company, it is the control of productivity. American labor costs, in general, tend to be in the range of 10%-15% of total costs. American coal mining labor costs, however, exhibit ranges of 30%-60% of total costs. Is it any wonder that the industry finds itself at a competitive disadvantage? When labor costs take as much as sixty cents of every dollar of revenue, there is little room for profitability. The American coal mining industry must set as a long range goal the reduction of labor costs to the 10%-15% range of total costs in order to be competitive.

Jan 1, 1986

By J. Groppo, W. Zhang, R. Honaker

"Rare earth elements (REEs) found in coal are in the form of minerals, ion-adsorbed onto clay surfaces or inner layers, or organically bound. Rare earth minerals such as monazite exist in coal and have grain sizes smaller than 5 µm. In this study, froth flotation was successful in concentrating rare earth minerals existing in a thickener underflow material derived from Fire Clay seam coal that contained around 431 ppm of total rare earth elements (TREE) on a dry ash basis. Conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2,300 ppm TREE. Using a laboratory flotation column to limit hydraulic entrainment, the TREE content was further enriched to around 4,700 ppm, which equated to an enrichment ratio of 10:1.IntroductionRare earth elements (REEs) are becoming increasingly important and have been widely used as raw materials for the production of phosphor, metal catalysts, magnets and batteries (Binnemans et al., 2013; Zhang et al., 2015). REE recovery from alternative sources such as coal and coal byproducts has the potential to stabilize the economic viability of coal mining operations while providing a dependable supply of critical materials.The average REE content of the world’s coal resources is around 60 to 70 ppm (Zhang et al., 2015). There are many well-known coal beds with high contents of REEs such as those in the Far East coalfields in Russia with contents of 300 to 1,000 ppm, the Fire Clay coal seam in eastern Kentucky in the United States with contents around 500 ppm and the Sydney Basin in Nova Scotia, Canada, with contents of 72 to 483 ppm (Birk and White, 1991; Seredin, 1996; Hower, Ruppert and Eble, 1999; Blissett, Smalley and Rowson, 2014). The occurrence of REEs in coal and coal byproducts can be classified into three types: (1) rare earth minerals, such as monazite and xenotime, (2) ion-adsorbed REEs on clays and (3) REEs associated with organic matrices. The rare earth minerals in coal and coal byproducts are very small in particle size, generally on the micrometer and/or nanometer scales (Honaker et al., 2014). Froth flotation, which concentrates minerals based on surface chemistry differences, has been widely used to treat fine rare earth industrial minerals such as monazite, xenotime and bastnaesite (Abeidu, 1972; Cheng, Holtham and Tran, 1993; Pavez and Peres, 1994; Pavez, Brandao and Peres, 1996; Jordens et al., 2014). As such, flotation is a promising method for the concentration of rare earth minerals from coal and coal byproducts."

Jan 1, 2017