Search Documents

By A. B. Cecala

An evaluation was recently performed on a district recirculation system at a trona mine in Granger, Wyoming. A 1.52m (5 ft) diameter, 37.3kw (50 hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated approximately 31.4 m'/sec (66,578 ft'/min) of air back into the intake. This amounted to a recirculation factor of approximately 20 pct of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 6l0m (2,000 ft) and 1,829m (6,000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane, and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF. tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1991

By Michel Dagbert

In the exploitation of porphyry-type deposits, the quality of the ore is mostly defined according to its grade. Besides the simplest distinction, ore-waste, several grade categories may exist and they correspond to the different ways in which the ore is further processed. At the time of mining the selection of the different categories is done from extensive information available from blast holes. But planning has to be done before this information is available and it is necessary for the geologist to forecast, from exploration and development data alone, the possible outcome of the selection done later on a block, a level, or the whole deposit and ultimately predict the ore reserves and value of the deposit. A good statement of this problem has been presented at the 1976 AIME annual meeting by Williamson and Hueller (1976). They have shown that, if the cut-off values are directly applied to the estimated grade of blocks, a gross overestimation of the recovered tonnage of ore (14%) will occur. This problem, now termed "the vanishing tons problem" (DaVid, 1977) seems to be common in many open-pit operations and it has been explained several times (DaVid, 1972; Huijbregts, 1975). In order to solve it l.Jilliamson and Mueller proposed a solution based on compiling masses and masses of blast hole data available from mined-out portions of the deposit. They derived empirical correction factors which provide for every block, given its estimated grade, the expected tonnage and average -grade of each category of material within that block. The purpose of our work is to repeat the same exercise but ignoring the blast holes data i.e. we want to derive the correction factors from the only DOH data. Doing this, we are more in the real conditions where the valuation of the mine and are reserve analysis has to be made before production actually starts. Two possible ways to achieve this goal will be investigated and the emphasis will be on recently

Jan 1, 1977

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonites to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath, 1986 and personal communication). These bentonites typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X¬ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated" bentonite to the oilfield since specifications are

Jan 1, 1989

By Baojie Zhang

The main goal of this study was not only to investigate the effectiveness of the FGX Dry Separator for removing pure rock from run-of-mine coal producing a better feed stock for conventional coal preparation plants but also to optimize the FGX Dry Separator performance for producing a salable clean coal product without using the conventional wet coal preparation processes. A Model FGX-1 Dry Separator with feed throughput capacity of 10 tph was extensively tested at the Illinois Coal Development Park using two coal samples having distinctly different cleaning characteristics. Statistically designed experimental programs were conducted to indentify critical process variables and optimize FGX Dry Separator performance by systematic adjustments of critical process variable parameters. The coal cleaning performance of the FGX Dry Separator was evaluated for the particle size range of 63.5 x 4.76 mm in most cases, although FGX Dry Separator feed consisted of nominal -63.5 mm run-of-mine coals. The best cleaning performance obtained from the FGX Dry Separator is described by specific gravity of separation (SG50) and probable error (Ep) values of 1.98 and 0.17, respectively. The SG50 and Ep values for individual size fractions were as follow: 1.90 and 0.12 for the +50.8 mm size fraction, 1.95 and 0.18 for the 50.8 x 25.4 mm size fraction, 2.01 and 0.19 for the 25.4 x 12.7 mm size fraction, and 2.03 and 0.23 for the 12.7 x 4.76 mm size fraction. These process efficiency measures produced a clean coal with ash content of 13.38% from a feed coal with ash content of 34.45%. Ash content of tailings and middlings streams were 85.09% and 39.57%, respectively. Total sulfur contents of corresponding streams were 3.87%, 4.68%, 6.87%, and 4.62%. For a relatively easy to clean Illinois No 6 seam coal (Cleaning Index: 0.72), only about 0.42% of the clean coal (i.e., 1.6 float fraction) present in the feed was lost to the tailings stream. For a relatively difficult to clean coal (Cleaning Index: 0.53), about 0.98% of the clean coal present in the feed was lost to the tailings stream.

Jan 1, 2012

By D. W. Park

A vast majority of longwall operations in the United States use shield-type hydraulic supports to provide ground control along the longwall face. The three-dimensional finite-element technique combined with a progressive failure approach was utilized to simulate interaction between shields and surrounding strata and determine various loading conditions. In addition, a separate finite element model of the shield structure was made to study responses of each long wall shield to the different loading conditions. Shield responses under various loading conditions and the shield characteristics, such as shield stiffness, the ability of resisting horizontal forces, and the effect of shield height, were studied based on the results from finite-element analyses. The results can provide the basis of effective shield design and be used for evaluation of the shield performance. It is suggested to develop a technique incorporating the finite-element method to evaluate the real-time shield performance for the purpose of effective ground control.

Jan 1, 1992

By William Gleason

Despite a global slowdown in most mining sectors, Caterpillar, the world?s largest mining equipment maker continues to forge ahead with new, and improved offerings to the global mining industry. On Nov. 10, as part of its Loading and Hauling Mining Focus Session at its Tinaja Hills proving grounds south of Tucson, AZ, Caterpillar unveiled to customers and media its two latest mining products, the 994K wheel loader and 6020B hydraulic shovel. The Caterpillar 994K wheel loader builds on a nearly 25-year history of the 994 model but with one noticeable difference ? the 994K is bigger ? much bigger. Weighing in at 239,142 kg (527,218 lb) the 994 K is up to 20 percent larger and comes with up to 30 percent increase in payload capacity. This behemoth of a machine is currently being tested at Caterpillar?s Tucson Proving Grounds, Anglo Gold Ashanti?s Cripple Creek and Victor gold mine in Colorado and Taseko?s Gibraltor copper and molybdenum mine in British Columbia, Canada.

By M. Trim, Y. Sun, D. Tepavac, A. Kumar

Configuration of Rozelle Interchange Project’s ventilation system required design and construction of some of the largest and tallest underground civil caverns attempted in Australia. The paper focuses on the technical challenges of designing these caverns within a heterogeneous, generally weak sandstone under highstress conditions while providing a construction sequence that would align with the contractor’s preferred techniques and schedule. Various construction techniques were investigated, but ultimately an observational approach relying on a construction sequence and specialized instrumentation met both the designer’s and contractor’s requirements. Relevant data obtained from excavations and the construction monitoring program are presented within.

Dec 1, 2022

By J. LaForest, R. Riggle

In today’s challenging mining environment, everyone is focused on minimizing cost per ton. With haulage costs approaching up to 45% of the overall mining costs, and loader performance driving production, optimizing payload on the truck is a big opportunity. This paper will focus on technology’s role in loaders achieving the truck target payload. There are constantly new innovations in technology, but not everyone uses them correctly. Technology is intended to help achieve the next level of performance, but still requires the right people and processes to effectively utilize the benefits. In today’s mining business, miners, engineers, trainers, supervisors, and managers have ever increasing roles and responsibilities as never seen before in past decades. Technology can make these roles more efficient, but fully relying on the technology can detract from optimization. Sometimes the old-fashioned method of loading to a consistent pass match will provide a lower cost per ton. Before blindly trusting your technology feedback, know these three areas discussed in this paper: (1) Prerequisites to utilize technology in payload management; (2) Types of payload management technology; (3) How to use the data to manage operator behavior. The objective of this paper is to provide low-cost recommendations to efficiently increase production. INTRODUCTION Whether miners claim to have been around and experienced it all, or they are the data-driven new generation on the mine site, miners are expected to execute the mine plan at the lowest cost possible. So why is it so difficult to execute this task? Shouldn’t supervisors just have to staff the equipment, tell operators to have a safe day and tally up the numbers at the end of the shift? Let the technology system do the rest; what could go wrong? Lots. Having examined numerous mining operations that use the latest loading technologies over the past several years, one common denominator is the opportunity to improve loader operator performance. Mining companies seek help from consultants, training departments, performance reporting systems and an arsenal of resources. Armed with all this information, but the improvements don’t happen, what could have gone wrong? It comes down to people, not managing the resources to drive the right behavior and as a result, the mine’s performance is not where it should be. Understanding how to make “Great Miners” out of these people is critical to this constant struggle to move more with less and get the costs down. Extraction CPT (Cost-Per-Ton) is most sensitive to optimizing loader production which can be generalized into 3 categories of influence: machine specifications, cycle timing, and continuous management using technology. After establishing a basic production machine configuration, utilizing technology to manage cycle times, operator efficiency and payload can be advantageous. Prerequisites to Utilize Payload Management Technology It is important to begin with the primary considerations that enable the use of technology to continuously manage loading productivity. All systems are interdependent in mining, but these are divided into the simplest terms to remember. First, fix your timing and geometry.

Jan 1, 2019

By N. A. Abdel-Khalek

An experimental study was carried out to compare the results of laboratory column flotation versus conventional flotation for the cleaning of fine coals of different rank and their oxidized samples as well as discrete size fractions. Surface oxidation caused a significant reduction in the flotation yields achieved with both methods. However, the column flotation produced concentrates? of lower ash content. The recovery -size curve achieved with column was similar in shape to that obtained with conventional cell, with superior results in the region of fine fractions. The influence of some column operating parameters was also discussed.

Jan 1, 1990

By Aaron Archer, James Parkes

This paper presents design considerations for the major underground elements of the pending BCRUA Phase 2 Raw Water Delivery System Project. These elements include two Lake Taps; an 8,800 LF, minimum 10-ft OD intake tunnel; a suction chamber with 6 Pump Shafts; a 30-ft diameter, 300-ft deep Main Shaft; a 2,600 LF Transmission Tunnel with 78-inch steel liner; and a 130-ft deep shaft on the Transmission Tunnel. The tunnels and shafts will be excavated through the Glen Rose limestone. The design development included consideration for technical requirements, easements, third party commitments, previous local project experience, and constructability based on contractor outreach.

Jun 13, 2021

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By Manuel Gomez

This report presents prediction equations for eleven factors indicative of metallurgical coal quality which have been developed from data obtainable during exploration. Five coke strength parameters and six carbonization product yields have been predicted for coking coals having volatile matter contents in the range 16.3 to 42.1 percent, dry basis. The prediction models developed contain information from the proximate and ultimate analyses, the size consist, and the petrographic composition of coking coals carbonized in BM-AGA retorts at 800°, 900°, and 1,000°C. The equations reported have been evaluated with independent data derived from the 900°C carbonization of 33 binary blends. Present results show that metallurgical coal quality can be predicted ahead of mining. Capability to forecast coal quality is useful in mine planning and should provide basic information for optimization of blending and crushing techniques, leading to the production of uniform coke.

Jan 1, 1968

By Jodie Robertson, Isabel Barton, Cristian Caro

Prior to mining, all rocks contained in a mineral deposit must be placed in one of several categories known as ore types. Each ore type describes a different way that the rock will behave in processing. The ore type determines which process stream a particular mined unit will be sent to, sets expectations for process engineers and metallurgists, and forms the basis for recovery predictions and production estimates. At first, ore types are assigned mainly by geologists based on visible geological criteria (dominant ore mineralogy, estimated grade, rock type, alteration type). As metallurgical tests are carried out and process data accumulate, the resulting criteria may be factored into the ore typing process, typically as assays and recoverable metal using the relevant process(es). Other variables may also be incorporated into ore typing at operations if they are particularly important, such as grindability, preg-robbing, gangue reagent consumption, and the presence of especially deleterious minerals such as talc or smectite. The mine operation department may also redefine ore types and/or process destinations based on economic criteria. A “best” ore type is designated that (in theory) best describes how the rock will behave in processing. Codes representing this ore type are entered into the drill hole database, then interpreted on cross sections and level plans, and finally added to the block model. Ore types are iteratively reexamined and adjusted over the life of a project. Major difficulties in effective ore typing are (1) lack of communication between geologists and metallurgists, (2) the imprecision inherent in imposing clean categories on messy natural systems without discrete divisions, (3) the need for ore types to provide useful information for a wide range of processes, (4) difficulties in scaling up laboratory test results to mine production, and (5) conflict among geological, metallurgical, and economic criteria for ore typing.

Nov 8, 2023

By Praterm J. D.

The process parameters for effective utilization of nitric acid as an oxidant for copper-iron sulfides have been developed. Leaching variables found to be important were acid concentration, temperature, time, atmosphere, pressure, mineral type, particle size, and percent solids. Particular attention was devoted to analysis and control of fumes evolved during the oxidation. Responses recorded were metal extraction, elemental sulfur formation and oxidation, product gas composition and evolution rate, reagent consumption, and residue flotation response. The paper concludes by laboratory testing a flow sheet based on the above observations. Ninety-eight percent of the copper contained in a chalcopyrite-bornite concentrate was recovered, requiring 1. 6 pounds of nitric acid to be regenerated externally per pound of copper extracted. Iron remained in the leach residue as hydrogen jarosite and was ultimately rejected from the system by froth flotation. Sixty percent of the sulfur contained, in the heading concentrate reported in the elemental form; the remainder was oxidized to sulfate and eliminated with the hydrogen jarosite in the flotation tails or by neutralization of the solvent extraction raffinate with lime. Nitrogen was evolved primarily as NO and NO2; up to 3 percent N2O was also present. Gases containing sulfur were absent except when pyrrhotite was solubilized in the absence of soluble copper. In this case, H2S was evolved.

Jan 1, 1972

By S. Norman Kesten

The Galena mine is located astride the Polaris fault in the Coeur d'Alene district of northern Idaho. The surface installations are about a mile up Lake Gulch, the mouth of which is about 2.4 km (1 112 miles) west of the old town of Wallace. The mine had its beginnings when the first claims were located in the early boom days of the district in the 1880s and when the first underground ore bodies were opened up in 1917. During the ensuing 14 years, ore was mined from which were recovered 5.4 Mkg (12 million lb) of lead and almost 14.2 Mg (112 million oz) of silver. Workings consisted principally of a vertical shaft from surface to the 800 level and an offset underground shaft to the 1600 level, together with extensive lateral openings. High-grade silver-copper ore was discovered near the Silver Standard fault in the Sunshine mine, a few miles to the west, on the 1700 level in 1930. By 1937, the Sunshine and adjacent mines were producing silver-copper ore on a regular basis. In 1943 additional ore of a similar type was found along the Chester fault, to the east of the principal Sunshine workings. The interest of American Smelting and Refining Co. (renamed ASARCO in 1975) was aroused and the company's geologists determined that the Galena mine, idle since 1931, provided a geological environment in which similar ore might be found. After negotiations were initiated with the owners of the property, Callahan Zinc-Lead Co., the property in question was deeded to Callahan's wholly owned subsidiary, Vulcan Silver-Lead.

Jan 1, 1990

By Stephen C. Tadolini, Colton Cook, Cody Hildreth, Frederick Cybulski

"Broken and jointed ground is extremely hazardous and requires unique stabilization techniques to protect worker and critical entries. Bolting techniques, even the most advanced with pre-load to create roof compression, can leave large gaps of unconfined and separated roof. This roof can also be susceptible to water inflows which only exacerbate the support problem. These types of conditions existed on long term development main entry accessing several future longwall panels. The geotechnical assessment identified well-defined jointing systems that also permitted water to flow between the roof separations, which “lubricated” the roof material and minimized any frictional advantages. Chemical injection of a Polyurethane material, Minova Carbopur WS, was placed beyond the bolted horizon to move the water to the rib lines and reinforce the fractured and broken roof. The injection material permitted the effective use of bolting patterns and helped ensure long-term stability of these critical entries. The paper describes the evaluation techniques, design patterns, basis for chemical selection and application, and results and recommendations.BACKGROUNDThe injection of mine and underground civil structures using polyurethane (PUR) has been ongoing for over 50 years. The applications in mining have included gate road stabilizations, longwall set-up and tear-down entries, and simple consolidation of coal mine roofs. PURs have also been used for roof stabilization during longwall shield recoveries. Polyurethane injection was initially developed by the Bergbau-Forshung GmbH, a German coal mine research institute, in the early 1960s (Jankowski, 1972). The product became a standard stabilization method in Germany after its commercial introduction in 1971 (Knoblauch, 1994), and was successfully manufactured at the Minova Essen, Germany location for over 50 years. With the recent closing of the German underground mines, that manufacturing facility has been closed and moved to Katowice, Poland, where production continues today Injection products are also being successfully manufactured by Minova in Australia and the United States.Polyurethane injection in underground coal mines is used in difficult ground conditions in fractured immediate and main roofs. It is also common as a rock stabilization remedy to prevent longwall face caving during shield removal. As presented in the case study, polyurethane was applied to minimize the inflow of water from beneath a stream channel while providing reinforcement and consolidation of the fractured roof that had lost confinement. Polyurethane is a two-component system (Part A and Part B) that is injected into a borehole and can chemically bond to the rock, not relying on friction or mechanical interlock to provide support. The material is injected under pressure, coupled with a low viscosity and small particle size; it flows into roof fractures and separations, which are the paths of least resistance. New developments in low viscosity PUR materials allows penetration of cracks as tight as 0.002 inch (0.05 mm) wide. This also allows for the closures of extremely small cracks to minimize the inflow of water, even if the water is under pressure. Combinations of designed expansion properties and low viscosities make the materials ideal for minimizing and stopping flows of water from underground structures."

Jan 1, 2019

By Francis F. Pitard

The presence of elements, minerals, or chemical compounds in materials at very low concentrations is becoming a constantly increasing concern for several segments of the Industry. Some trace elements or chemical compounds may be considered as hazardous, some are simply considered as undesirable In complex processes where they could be constantly recycled and end up as the major factor of decreasing quality for some valuable products. In some other cases, the presence of a trace element or mineral may be highly desirable because of its economical value: precious metals are falling into this category, they probably were the first trace elements to draw our attention. Tremendous quantity of money is spent for analysis at the trace level, also the analytical "tool" has been considerably improved during recent years, but still the sampling aspect of the problem remains obscur for many, and because of it, large quantity of analytical efforts become meaningless. Not only the absence of sampling strategies is badly affecting the representativeness of a large majority of samples, but furthermore for the same reasons, many laboratories are failing In their endeavor to prepare reliable standard reference materials. The reason of this failure has its roots in the unability to estimate effectively the sampling characteristics of the element, mineral, or compound of interest, not to mention the unability to perform precise and accurate complete analysis, so essential for the instrumental analyst (1). In this paper a strategy to perform a better sampling operation is recommended. SELECTION OF A PROBABILISTIC APPROACH AS SOON AS PRACTICALLY POSSIBLE It Is essential to differentiate probabilistic sampling from non-probabilistic sampling. As Illustrated in Figure 1, the sampling operation Is a selection process which could be performed In two different ways: I. A probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with a same probability of being selected. 2. A non-probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with different probabilities of being selected.

Jan 1, 1986

By Kathleen Lagnese, Srikanth Muddasani, Kashi Banerjee, Carla Robinson

"Mine water generated from underground coal mining operations contains both dissolved and particulate solids. Dissolved solids primarily consist of sodium, calcium, magnesium, potassium, chlorides and sulfates. When discharged to a receiving stream without treatment, these constituents create a potentially toxic environment for aquatic life.A case study is presented to discuss how a centralized treatment plant treats mine water from six locations to meet discharge limitations for chlorides. Located in West Virginia, this facility consistently achieves less than the National Pollutant Discharge Elemenation System (NPDES) permit limitation of 218 mg/L chlorides in the discharge while generating almost zero liquid waste. The dissolved solids concentration in the influent ranges between 5,000 and 10,000 mg/L, with chloride concentrations of 1,000 to 2,000 mg/L and sulfate concentrations of 2,000 to 6,000 mg/L.The mine water is treated using advanced treatment technology to produce clean water for discharge or reuse. The treatment process comprises aeration, softening, filtration, reverse osmosis (RO) reject softening, evaporation, crystallization, final effluent remineralization and sludge dewatering. The solid waste generated in the treatment process is landfilled on site. The leachate is sent back to the facility’s thermal treatment process. Because no liquid waste leaves the property, this plant is termed a zero liquid waste (ZLW) facility.The advanced water treatment system was built to meet a new 218 mg/L regulatory limitation imposed by the West Virginia Department of Environmental Protection for chlorides discharged to surface waters. The system is designed to treat a maximum flow of approximately 795 m3/h (5 million gpd) of mine water. The treatment process utilizes RO membrane treatment to achieve the effluent criteria, and evaporation and crystallization technology to manage the RO concentrate from the water treatment process. As a result, the system produces clean water for discharge while generating zero liquid waste. The effluent water can be used for industrial purposes or discharged to a receiving stream. A water impact index (WIIx) study indicated that discharge of this high-quality water into the Monongahela River watershed may improve the water quality for downstream water users. The waste produced in the treatment process, including softening sludge and salt, is disposed of in an onsite landfill. Currently, the plant is treating at an average flow of 490 m3/h (3.1 million gpd) of mine water with an average influent chloride concentration of 1,530 mg/L and an average effluent chloride concentration of 11 mg/L."

Jan 1, 2014