Search Documents

By J. Kang

To obtain microbial cultures with the ability to efficiently leach copper ion from chalcopyrite, microbial samples from acid mine drainage sites were mixed and then subjected to mutation using sodium nitrite (NaNO2), diethyl sulfate (DES), ultraviolet light (UV) and their combinations. Mixed cultures with a much stronger ability to leach copper ion (identified as mixed cultures A, B, C, D and E) were obtained by screening on leaching media. Leaching tests showed that mixed culture E had the best leaching performance and increased the Cu2+ content by 120.5% in 20 days, compared to a control without mutation treatment. Mixed culture E grows well on Leathen leaching medium supplemented with Cu2+ (at a final concentration of 32 g/L), reaching 3.2 × 107 cells/L after 15 days, while the unmutated control culture cannot survive beyond 15 days, indicating that mixed culture E is more tolerant of high concentrations of Cu2+. In addition, continuous leaching by mixed culture E is very effective at a pulp density of 1%. These results suggest that it has the potential for industrial applications.

Jan 1, 2008

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud.INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1]."

Jan 1, 2018

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud. INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1].

Jan 1, 2019

By N. R. Sainath

This paper discusses the results of a laboratory investigation carried out to study the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 1.5 and 4 inch diameter cores were mapped by visual inspection. The cores were stressed in a triaxial stress field representative of in situ conditions. The permeability of the samples to water was then estimated. The samples were exposed to 20 g/l sulfuric acid and the experiment repeated. The Permeability of unleached samples ranges from 10-1 to 10-19 m2 and it increases as leaching progresses. The porosity variation and the rate of recovery of copper from the specimen during leaching were also studied.

Jan 1, 1991

By Jan Wolf

The iron ore industry presently utilizes two types of de-posits. The first are the high grade deposits generally located in remote areas and, secondly, the low grade de-posits which are normally found nearer to the steel-making centers. The high grade deposits produce a direct shipping ore which has an iron content which may be close to the maxi-mum 70% of Fe. These deposits have reserves which are ex-pressed in billions of tons. The ore needs little or no up-grading and where this is performed is restricted to ore washing. With the large demand for iron ore pellets, plus a national drive to perform as much of the upgrading as possible in the native country, there is a trend to erecting pellet plants at the mine location~ Large iron ore suppliers such as Australia, Brazil, Venezuela and Liberia already have pellet plants in operation, and there are new plants projected or expansion projects under study. The low grade ores are mined at locations closer to steel mills such as in Minnesota, Michigan and Canada. These low grade ores require methods of beneficiation to obtain a commercially accept-able product with the modern beneficiation techniques it is no~, possible to produce iron ore pellets of 68% Fe and 4.5% silica from ores containing as low as 26% Fe. Figure 1 gives a general picture of the types of iron ores and their beneficiation. The final product of the high grade ore is a coarse concentrate, sinter product or pellets. The final product of the low grade ores is pellets and, in some cases, coarse concentrates.

Jan 1, 1971

By Dan Brunner, Scott Thomson, Ben Lyddall, Duncan Thomson

Geosensing is used in oilfield drilling in conjunction with geophysical tools to support characterization of rock properties, geology, and reservoir conditions. This technology is now available to the mining industry and has been successfully applied to underground in-seam directional drilling in Australian coal mines for geologic exploration and methane drainage. The system utilizes a range of drill rig and wellhead mounted sensors which, combined with analytical software, produce real-time data from which 3D spatial features can be accurately modelled significantly in advance of mining. This innovation greatly expands on the information obtained from current in-seam directional drilling practices and provides for improved characterization of coal seams, including soft and weak zones, locations of geologic discontinuities, and analysis of formation flow. This paper provides a description of the geosensing system and the interpretation of actual data from long in-seam directionally drilled methane drainage boreholes at mines in Australia, and discusses how this system increases the value of directional drilling as an exploration tool for the coal mining sector, and the evaporite and hard-rock mining sectors where directional drilling is also applied.

Feb 1, 2024

By R. H. Sailors

During the last 15 years, the North American Mining Industry has experienced increasing usage of cast high chromium white iron grinding media in wet grinding applications. First introduced into the cement industry (klinker grinding) where wear rate reductions of four or five times have been realized compared to steel balls, this same grinding media serve the iron, copper, and phosphate markets by resisting not only impacts and abrasion, but also corrosion which occurs in wet grinding. In these markets, single mills containing 250,000 kg of grinding balls are not un-common and hence the economic potential with respect to lower wear rates can be significant. Add to reduced wear rate the increased production efficiency that is possible and it is readily understood why much of the mining industry uses cast high chromium grinding media. Metallurgically, the alloys used consist of a martensitic matrix containing hard M7C3 eutectic carbides. Carbon (2.0 to 3.5%) and chromium (12 to 277.) are characteristically used to arrive at the desired properties.

Jan 1, 1989

By G. Bitsianes

An experimental procedure was developed for studying magnetic roasting on a accurately-controlled laboratory scale. The loss-in-weight method was used and the course of reduction could be followed under a reducing gas atmosphere containing as many as five different components. Some important variables of the operation were checked on a marginal Mesabi iron ore containing porous and dense varieties of hematite as well as pure goethite. The conditions simulated were those for the grate roasting of a coarsely-sized ore burden. Temperature was maintained at 600°C; gas composition at 4.25% CO, 4.25% H2, 17.0% CO2, 15.0% H20, and 59.5% N2,, and gas flow rate at about 1,5 lineal feet per minute. The ore charge was composed of quarter-inch cubes. Under these conditions, the ore porosity was found to be one of the governing variables of the operation. Results showed that an ore size limitation existed as a function of this ore porosity. For efficient magnetic conversion, the size limit was 3/8 inch for very porous ores and about 65 mesh for very dense ores. An anomaly was noted in the weight losses incurred during actual magnetic conversion. For goethitic ores, these were generally about 13 per cent higher than could be accounted for theoretically. The effect was attributed to possible non-stoichiometric structures forming during the reduction process.

Jan 1, 1960

The dissolution behavior of gold and copper from their elemental states and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc electrode. The anodic and cathodic reactions were studied separately and the resulting polarization curves were combined to examine the overall dissolution reactions. The dissolution rate of pure gold in the aerated cyanide solutions was inhibited by the anodic passivation on the gold surface, while the dissolution rate of pure copper was found to be mass-transfer-controlled. On the other hand, the dissolution of gold and copper from the alloys was partially controlled by electrochemical reaction and largely by mass transfer.

Jan 1, 1994

By Odin Wilhelmy

Agriculture in the United States today is becoming more and more a business, rather than a way of life. In the light of this, it behooves the farm-supply industries that provide the American farmer with his tools of production--feed, fertilizer, machinery, and the like--to give even greater attention than they have in the past to meeting the needs of the farmer-businessmen they are serving. Increasing competition among the companies that make up these industries merely accentuates this need for better service. An opportunity for such improved service, not yet fully realized, exists in the fertilizer industry today. That opportunity lies in the increased transportation of fertilizer ingredients by water. However, before the benefits inherent in this increased water movement of fertilizers can be fully realized, certain obstacles must be met and overcome. It is the purpose of this paper to outline the nature and magnitude of this opportunity, to point out some of the roadblocks and the steps that can be, or are being, taken to remove them, and to indicate some of the rewards that would logically stem from success in these efforts.

Jan 1, 1961

By John Drew Ridge

Recent work by Haas has made available information on densities and vapor pressures of solutions of differing salinities at temperatures up to 330°C. From these data it is possible to predict the behavior of volcanic exhalations of various degrees of salinity as they approach the sea floor. Particular attention is devoted to solutions of 5.0 weight per cent NaCl and 20 weight per cent NaCl, two fluids that approximate quite closely the salinities of what Roedder termed: (1) normal hydrothermal fluids and (2) fluids typical of stratiform deposits of low-temperature conditions of origin. It is apparent that solutions above 220-230°C. cannot reach a sea floor on which the depth of water is 600 feet or less in the liquid state but will boil at some appreciable depth beneath the sea floor. Such boiling would result in the precipitation of all constituents of the ore fluids of significantly lower vapor pressure than water. The principal such constituent would be salt, and no sulfide deposits, the major constituent of which is salt are known. It follows, therefore, that ore fluids probably never get close to the sea floor of shallow seas at temperatures high enough to permit boiling. Ore fluids significantly above 230°C. can reach the sea floor in the fluid state only if the depth of the sea in the area. in question is well above 600 feet, for example, solutions at temperatures of ±300°C. reach the sea floor in the liquid state only if the depth of sea water is slightly over 3000 feet. Ore fluids reaching the sea floor at such depths may be the parents of such fluids as the Red and Salton Sea brines. On the basis of these data, the Cyprus and Kuroko deposits are discussed.

Jan 1, 1973

By G. J. C. Young

In 1986 the city of Johannesburg celebrates its first century of existence. The fact that the city was founded to exploit the gold deposits which underlaid it, prompts this review of the gold process development in the mining industry of South Africa. Clearly a complete history of, the gold recovery process to date is not called for and it is proposed therefore to outline the most significant developments which have taken place since the middle 1930's, that is to say the last 50 years or so. Prior to this period the industry had seen the development of comminution processes employing cone crushing in closed circuit with vibrating screens followed by grinding in rotating mills and the gradual disappearance of stamp mills. The all sliming process was well established as a viable route and continuous dewatering in thickeners, continuous leaching and filtration were serious rivals for the earlier batch processes. Continuous processes for gravity concentration had also been developed and the recovery of gold from pregnant solutions employed cementation on zinc dust as opposed to shavings. Thus at the beginning of the half century under review the industry had adopted, or started to adopt, many of the processes still accepted as modern practice. However in some areas little change was evident this was especially so in the smelthouse where some thirty more years were to elapse before the hand stoked coal fired calcine and reverbatory furnaces were replaced by more environmentally acceptable electric furnaces. The most significant feature in recent history has been the mining of progressively lower grades of ore and the retreatment of tailings from earlier operations, much of the latter comprising tailings only a decade or even less in age. Notable among these operations are those on the East Rand near Springs in the Transvaal, in the Orange Free State at Welkom and more recently, massive reclamation of tailings close to the city centre itself. The carbon in pulp (CIP) process has been much publicised in recent years and all new plants erected during the 1980's have adopted this route for gold recovery. However the major proportion of tonnage milled in the industry is still subjected to the more traditional process of liquid solids separation by vacuum filtration. The discussion that follows will centre largely on the developments in the traditional process route, which for the sake of completeness is listed below: Comminution Dewatering Leaching Liquid solids separation Gold recovery Smelting

Jan 1, 1985

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By Shankar S. Hegde

In many areas of the United States much of the most readily minable coal is nearing depletion, while at the same time, increased national attention is being given to coal as a major alternate energy source. If some of the thinner, more erratic, deeper and lower quality coals, which comprise the great bulk of U.S. resources, are to be mined efficiently and economically, greater attention must be devoted to careful planning of mines and to preparation facilities. One of the cornerstones to careful and successful mine planning is precise knowledge of coal thickness and areal distribution, roof and floor quality, and seam quality. Data on which this knowledge is based are obtained from various borehole techniques and, in some cases, seismic methods. Despite the many technical innovations that have been made in acquiring subsurface data, little attention has been given to the problem of systematic storage and retrieval procedures of the data and assembling them in a form that can be used for various computer mapping programs now available. (See Bilter and Martin, 1977; Bryant and Zobrist, 1977 and Farrell and Wherry, 1978). The purpose of this paper is to describe a series of user oriented programs developed over the past five years which are specifically designed for precise logging of rock core, accurate storage and retrieval of this data, correlation of seams between logs, tagging seams, computer assisted data posting of maps and preparing maps and profile sections for report illustrations. The entire system stresses increased precision and speed for a series of operations which are now largely manual, time consuming and prone to error.

Jan 1, 1980

By Thomas A. Wheeler

The reagents commercially used in coal flotation and their roles are reviewed and discussed According to their function the reagents are divided into often overlapping groups: 1. Collectors 2. Frothers 3. Conditioning Reagents Frothers have by far the largest effect on the amount of coal recovered They act not only in their traditionally accepted function of “bubble makers”, but in coal flotation they serve in a seldom acknowledged role of collectors. A lab flotation study on four samples of different coal ranks shows how these react to various frother families and proves that no froher is the optimum reagent for all types of coal. The advent of new technology in flotation equipment in the past decade has resulted in various novel designs of column cells, Jameson and Centrifloat™ cells, air-sped hydrocylones, etc. All should require special frothers or blends of frothers to meet their specific needs.

Jan 1, 1994

By D. S. Dick

Over the last few years, new methods to characterize the flow properties of bulk solids have been developed. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field conditions. In addition, the effect of large particles on a material's flow properties (cohesive strength, bulk density, wall friction) can be determined as well as the effects of various additives such as Freeze Conditioning Agents. New developments have also taken place in terms of devices to improve the reliability of solids flow. Much attention has been paid to finding ways to provide a mass flow pattern with relatively shallow hopper walls through the use of inserts. Such devices can also provide reliable in-bin gravity blending of bulk solids and/or completely non-segregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. Many of these developments have direct application in the mining and minerals processing industries. Examples of each will be highlighted.

Jan 1, 1988

By J. Hanna, I. J. Anazia

The Mineral Resources Institute (MRI) has developed a unique process for selective fatty-acid flotation of phosphate minerals from siliceous ores. The process takes advantage of preferential adsorption (over silica surfaces) and high reactivity of fatty-acid collectors toward apatite under slightly acidic conditions (pH 5 - 6.5). The process was successful in upgrading various Florida and North Carolina phosphate samples containing 7.7% to 15.3% P205 and 62.3% to 77.2% siliceous gangue (Insol). The resulting concentrates assayed 28.1 % to 33.1 % P205 and 4.1 % to 9.9% Insol, with high P205 recoveries of 81.8% to 92.2%. Depending on the degree of surface contamination of the silica particles in the flotation feed, one or more cleaning steps, with or without sodium silicate, would be required to achieve higher-grade phosphate concentrates.

Jan 1, 1994

By Marcel Laflamme, Sebastián Ibarra‑Gutiérrez

Improvement on controlling the stope limits has enabled the assessment of technical performance in several underground mining operations. Technical performance, integrated to stope geotechnical and geomorphological parameters, constitutes the basis which guides mining engineers in the Mineral Reserves Estimation process. Moreover, there are established definitions to report this information in Canada, incorporated in NI 43–101, which stipulates that “A Mineral Reserve includes diluting materials and allowances for losses that may occur when the material is mined” [1]. However, some loopholes have been identified regarding practical standards followed to specify the way to include and report ore losses when the lost material was blasted and must be left behind unrecovered inside the stope. In fact, general efforts to estimate and quantify the negative effects of operational ore losses only consider under-break ore loss. However, mining engineers frequently confront situations requesting the anticipated closure of a stope. Therefore, reconciliation process should reflect the amount of unrecovered Mineral Reserve. This work presents a discussion of possible practices to integrate adequately operational ore losses consisting of blasted but not recovered material and focuses on how different approaches regarding the material constitution could severely affect the stope technical performance interpretation.

Aug 9, 2021

By B. J. Vorster

The South African Iron and Steel Company Ltd operates a large Iron Ore Mine in the Cape Province of the Republic of South Africa. The Mine is situated on the farm, Sishen, approximately 600 km west of Johannesburg. The annual capacity of the Mine is 100 million ton of ore and waste and the present production level is 60 million ton. The Mine operates continuously for 6 days a week. The primary equipment used to maintain the above production are 55, 154 t trucks (Wabco and Unit Rig) and 14 P & H shovels. During 1979 an urgent feasibility study into the application of a trolley assist system was launched at the Mine. This was due to the unrealistic escalation in the cost of diesel fuel and the appeal from the South African Government to reduce the use of fossil fuels. Tests and economic evaluations proved the system technical feasible. The estimated discounted cash flow return exceeded 50% and the diesel fuel consumption would be reduced by 120 million litres in the next 10 years. Management subsequently approved the implementation of the system at Sishen. The construction of 7,7 km of line and the conversion of 66, 154 t trucks were completed in March 1982.

Jan 1, 1985

By Ben Sosewitz

The subject of rapid excavation tunneling is one that is extremely important to the people in the Metropolitan area of Chicago. My personal observation is that it is also extremely important to the urban communities around the U.S., to many local and state governments, and to the public officials who are deeply concerned about state affairs and taxes. The Metropolitan Chicago area is in fact, (as are 40 other major urban areas in the U.S.) confronted at the present time with a very serious combined sewer overflow, drainage and pollution problem which accounts for an estimated 40% of the pollutional load on its waterway system. In response to this the District has to date spent some seven millions of dollars in an attempt to find the most economical solution available for the elimination of this problem. This study included extensive investigations of the geological strata, the quantity and quality of storm runoff to be dealt with, and the various methods of storage and treatment available. It has considered solving the overflow problem by a concept involving a series of tunnels, rock tunnels, shafts and storage areas which will collect, retain and subsequently treat that portion of the combined sewer overflow which can be handled in the most cost-effective and economical way, consistent with following the federal and state standards - with which we at the present time agree in principle.

Jan 1, 1997