Search Documents

By Michel Grenier, David A. Young, Brent Rubeli, Mahe Gangal

This work forms part of a study being conducted into the feasibility of constructing a prototype Load Haul Dump (LHD) vehicle for operation in underground Canadian mines. A series of in-laboratory assessments were performed to determine the relative contributions of a Deutz F4L912W (54 HP- conventional vehicle engine) and a Deutz F2L 2011 (31 HP hybrid vehicle engine) to diesel emissions concentration during mine transient duty cycles and steady-state operating modes respectively. Results indicate significant reductions in the quantity of gaseous and particulate emissions with the application of the hybrid system and a high-efficiency ceramic element filter. This paper describes the engine test protocols and the results of this laboratory study.

Jan 1, 2006

By G. R. Giuliani

Hanna Mining Company's Groveland Mine is located in the Upper Peninsula of Michigan. The low grade iron ore deposit consists of a mixture of magnetite and hematite with chert, jasper, quartz and various iron silicates (1). The ore is beneficiated by magnetic separation and anionic flotation of the iron minerals with chemical depression of the silica. The magnetic concentrate makes up about 75% of the concentrate. The concentrate is pelletized at the rate of 2.0 million LTPY of pellet production. The concentrator facilities were started up in 1959 and the concentrate was marketed as sinter feed until 1963 when the concentrator was expanded and the pelletizing plant was added. The pellet plant now consists of regrinding, elutriation, filtering, balling and induration. The pellet machine is a straight grate which employs updraft drying and cooling and downdraft drying, preheat and firing. It is necessary to regrind the concentrate before pelletizing. The con-centrate is 60% passing 325 mesh, with a surface area of ±lOOO cm2/Gm, and must be ground to about 83% passing 325 mesh, 1600 cm2/Gm blaine surface area, for pelletizing. The energy for regrind has been reduced from 12.5 KW per LT to 8.80 KW ate of 2.0 million per LT. This was the result of changes made in the concentrator where originally a coarse spiral concentrate, instead of the magnetic concentrate which is screened on fine screens to reduce the coarse fraction and prevent overgrinding before flotation, was produced. Also in 1968 an additional concentrating line was added to the concentrator which employs more grinding power than the other three lines. The demand for a high iron grade and lower silica pellet resulted in the investigation of different schemes of upgrading the reground concentrate which had more iron values liberated during grinding for surface area. The reagentized material presented many problems, mainly in selectivity trying to flot the iron and with high reagent consumption having to dereagentize the concentrate for amine silica flotation, in the various flotation systems tried. Tests were then conducted with elutriation (2) which proved satisfactory by removing the lower specific gravity, fine gangue material from the heavier material with the

Jan 1, 1977

The SFR system utilizes a skimmer or extractor placed at or near the slurry-froth interface where there is a higher concentration of valuable mineral particles. With assistance of hydrocyclones, it is possible to classify the extracted particles into coarse and fine particle streams, that can be handled separately. It also allows the coarser solids to be separated from entrained low-value fines. The first test results with the SFR system significantly improved both coarse and fine particle recovery in a flotation cell. The SFR system was tested in the flotation circuit at a copper-moly concentrator, and the results show that the use of the skimmer has huge potential to increase the froth recovery (Rf) of both molybdenum and copper.

Jan 1, 2012

By E. Stone, R. Reagan

Risk of hand injury is very real for operators carrying out conventional bolting operations with power torque tools, reaction arms and backup wrenches. Bolting operations of this type are common today in the installation and maintenance of heavy mining machinery and equipment. Newer solutions have become available that have the potential to dramatically reduce the risk of hand injuries in mining applications. MINING APPLICATIONS Within the scope of mining operations, various types of equipment are used such as tunnel boring machines, bucket wheel excavators, draglines, material handlers, screens, pumps, crushers, continuous miners and longwall systems. Design of these machines typically includes larger diameter bolts for strength and durability. Due to rugged use all machines require frequent maintenance and service which requires the use of heavy industrial bolting tools and methods. Those engaged in bolting operations include technicians working for end-users, equipment manufacturers, general contractors and others who provide services in mining operations. Most all personnel involved with these activities are engaged with use of high power bolting tools and procedures. Training is essential to raise the awareness of bolting safety and to avoid accidents. However improved bolting tools and procedures can play an even more significant role in further improving the safety of all those engaged with bolting in the mining industry. SAFETY CONCERNS Professionals working in the mining industry are constantly looking for ways to further reduce risk to health and safety. Bolting operations which are fundamental to service and maintenance of mining equipment are often overlooked as a potential area for improvement. Several areas of bolting operations offer potential for improvement in safety and avoiding accidents during equipment maintenance. This paper addresses the safety concerns associated with reaction arms and backup wrenches in conventional bolting applications (Figure 1).

Jan 1, 2019

By Vincent Tricot, Daniel Altier, Roger Storry

"INTRODUCTION The Liantang / Heung Yuen Wai Boundary Control Point (BCP) project, located in the north-east New Territories of Hong Kong, will form the seventh land crossing between the Hong Kong Special Administrative Region (HK) and Shenzhen in China (Figure 1). The BCP project comprises an 11km long dual two-lane trunk road linking the border crossing facility to the existing road infrastructure in HK and when completed it will facilitate future regional development and alleviate frequent traffic congestion at the existing Boarder control points.In December 2013 Dragages Hong Kong (a member of the Bouygues Construction Group) was awarded the 5.4km long Contract 2 section of the project, including the 4.8km long Lung Shan Tunnels, by the Civil Engineering and Development Department of the Government of the HK SAR. To overcome the difficult ground conditions anticipated along the Contract 2 section of the project the tunnels will be constructed using mechanical and drill and blast (D&B) excavation techniques together with a 14.1m diameter multi-mode Earth Pressure Balance Tunnel Boring Machine (TBM). Land constraints imposed on the project alignment require that the final 500m section at the northern end of the Lung Shan tunnels, under Princess Hill (Figure 2), takes an almost 90 degree turn towards the north. The resulting 354m radius curve restricts the sight-line of road users to below the minimum 110m at 80km/hr hence, the internal span of the tunnels needs to be increased from 12.6m, in the standard straight section, to 15.4m in this curved section to accommodate a widened shoulder which will provide the required sight-line distance."

Jan 1, 2016

By R. Mensah-Biney

The adsorption of gold-thiourea complex onto a cation exchange resin, Amberlite 252, has been evaluated in a batch stirred reactor. The observed non equilibrium saturation capacity was 3.20 meg Au/g dry resin (620 kg/t) whereas the equilibrium ion exchange capacity was only 0.53 meq/g (103 kg/t). The enthalpy of adsorption was 4 -25 kJ/mole under equilibrium conditions and increased to 20-200 kJ/mole under non equilibrium conditions. Under non equilibrium conditions, the adsorption capacity of the resin decreased with increasing temperature and increasing thiourea concentration and increased with increasing gold concentration. This dependence of adsorption capacity on thiourea concentration and temperature may be a useful tool for elution of gold from the loaded resin. Scanning electron microscopy revealed evidence of deposition of elemental gold on the loaded resin under non equilibrium conditions. The proposed mechanism for "adsorption" of gold-thiourea complex onto this cation exchange resin consists of an ion exchange reaction followed by a reduction of the exchanged gold complex to elemental gold on the surface of the resin.

Jan 1, 1997

By K. A. Natarajan, M. K. Yelloji Rao, P. Somasundaran

The bacterium Thiobacillus ferrooxidans triggers the surface modification of sulfide minerals to provide hydrophilicity or hydrophobicity for the flotation of sphalerite and galena. The effects of initial cell concentration, period of biotreatment and pulp density on the floatability of the minerals are discussed. With galena, flotation enhancement obtained through sulfuric acid treatment was retarded by biotreatment at all cell concentrations due to chemical effects. Such a decrease occurred for sphalerite only at cell concentrations sufficiently high for bacterial attachment to the mineral surface. The variables affecting surface modification (and, thus, flotation response of the minerals) include the cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Although bacterial growth during biotreatment was observed even in the absence of nutrients, such growth was more common in the sphalerite suspension than in the galena suspension. Cell protein estimations suggest that more cells are attached on galena than on sphalerite. Probable reaction mechanisms associated with bacterial modification are discussed.

Jan 1, 1993

By J. R. Evans

Mining claims must have a discovery of a valuable mineral deposit to be valid. When required, a Federal government mineral examiner makes a determination of validity and recommendations thereof to authorized management officials. The examiner should show whether or not an existing mining operation, or a proposed operation have economic viability. This is accomplished through an analysis of legal entities, land status and use, geologic and mineralogic relationships, and mining, milling and processing techniques considered in an appropriate economic evaluation framework. A framework involves market and market entry studies, reserve analyses, all costs analysis, royalty buyouts, tax structure, discount rate of return, and escalation and risk factors. An income approach to value is then used by means of a simple or complex discounted cash flow (DCF) analysis to certify validity. Whether one claim is owned by a single miner, or hundreds of claims are owned by a large corporation, thorough, fair, consistent, and appropriate economic concepts should be applied by the mineral examiner.

Jan 1, 1993

By Brian Y. Lattimer, Kray D. Luxbacher, Jonathan L. Hodges, Manuel J. Barros-Daza

The abstract discusses the importance of predicting fire response time (the time before conditions become untenable for firefighters) in underground coal mines. It introduces a data-driven approach using artificial neural networks (ANNs) to predict response time and fire size based on measurable parameters like CO concentration, mine geometry, air velocity, and time since fire detection. The approach was tested using simulations from fire models (FDS and FSSIM), showing promising results for real-time predictions during mine fires.

Mar 6, 2022

By Rennie B. Kaunda, Robert J. Sterrett

Some people in the mining-engineering field mistakenly believe that mine-water management primarily revolves around the treatment of mine waters that fail to meet applicable water-quality standards. While water-quality control is undoubtedly important, it represents only a fraction of what constitutes comprehensive site-wide, minewater management. A more holistic perspective recognizes that it also involves mine dewatering to maintain safe and workable conditions, securing sufficient water supply for operations, strategically handling surface water within and surrounding the openpit to prevent issues like flooding, developing robust post-closure plans to mitigate long-term environmental effects, and proactively minimizing any adverse impacts on local communities and ecosystems. This article provides a brief overview of topics that fall within the concepts of mine-water management. The focus is on openpit mines, as they are generally larger than underground mines. The management of mine water is highly dependent on local and regional climate such as tropical, desert or temperate climate. Each climatic setting has its own unique challenges, but there are also commonalities.

Jun 1, 2025

By Basak Anameric

This study reports preliminary feasibility investigations for utilization of the selective carbothermic reduction and smelting (SCRS) processing scheme to beneficiate low-grade iron-manganese (Fe-Mn) mineral deposits from MN, USA. The study includes laboratory-scale demonstrations using an induction furnace and production of various products by manipulation of operational parameters. The products include alternative iron (Alt Fe), high carbon ferromanganese (HC FeMn), alternative silicomanganese (Alt SiMn), and upgraded manganese concentrate (Mn conc). All of these products have commercial value and can be used in various applications as raw materials.

Nov 23, 2020

By Ben Roderds

The Waneta Expansion Project (WAX) is located near the existing Waneta Dam site at the confluence of the Pend d?Oreille and Columbia rivers, approximately 10 km (6.2 miles) south of Trail, BC, Canada. The WAX owners consist of a partnership between Fortis Inc., Columbia Basin Trust and the Columbia Power Corp. This design-build project was awarded to SNC-Lavalin in late 2010 and is expected to be operational in mid-2015. The WAX consists of a new 335-MW powerhouse, including two new Francis turbine units, each generating approximately 167 MW. The powerhouse is located downstream of the existing Waneta Dam, and will make use of excess water that would otherwise be spilled during the runoff season. Water will be funneled to the turbines through an intake structure and two 10.5- m (34.5-ft) diameter, concrete-lined Penstock Tunnels. A 10-km (6.2-mile) transmission line will connect the powerhouse to existing electrical grids. Redpath/FKCI Waneta Tunnelers (RFK) was subcontracted by the heavy civil contractor, the Aecon/SNC Lavalin (ASL) joint venture, to excavate the two penstock tunnels and install the cast-in-place concrete liner. RFK is a joint venture partnership between J.S. Redpath Ltd., an underground mine contractor located in North Bay, Ontario, and Frontier-Kemper Constructors ULC, a heavy civil tunneling contractor based in Nova Scotia, Canada. Since penstock tunnel excavation was planned using drill-and-blast methods with a significant grade of more than 17 percent, the combined experience of these two contractors was a perfect match.

Mar 1, 2014

By N. Aouad

The deployment of large machinery for low cost, bulk surface mine production operations has resulted in high-impact shovel loading operations (HISLO). In extreme cases, shovels load large dump trucks with 100-ton (or more) passes generating high-impact forces under gravity. HISLO generates high-frequency shockwaves that cause severe truck vibrations exposing operators to whole body vibrations (WBV). Current research study in this area has established that the vibration levels affecting the operator?s seat, lower-back, lumbar and cervical regions fall within the extremely uncomfortable zone compared to the ISO 2631 comfort zone. These results pose health threats to truck operators over long-term exposure to these vibrations. In this paper, the authors will examine engineered solutions to mitigate these health threats.

Jan 1, 2011

By S. E. Younis

The mining industry is currently looking to better understand, anticipate, and be able to mitigate business and operational risks in order to deliver the rewards of risk taking, and to minimize the frequency and impact of risk on the downside. Assessing risk works from the premise that the identification and management of existing risks can be very challenging, especially when threats are not easy to detect, the likelihood of occurrence is difficult to gauge, and/or the consequences are uncertain. Some approach this as a ?check the box? task, even though fire and safety incidents continue to occur and investigations often find the hazard analyses did not properly identify the cause or consequence. You cannot engineer protective designs and safeguards for causes and consequences that have not been identified appropriately. For the mining industry, risk management is an important tool for making critical decisions and, in some cases, meeting regulatory requirements. Providing high-quality documentation that meets both regulatory and corporate requirements is critical for maintaining safe, uninterrupted mining operations. Risk management is a five-part process: 1. Identify the hazards and their causes, 2. Determine the hazard consequences, 3. Calculate the frequency of occurrence, 4. Quantify the risk associated with the system, process, or procedure, and 5. Provide feasible solutions for the risks

Jan 1, 2012

By R. J. Lee

Asbestos analysis is conceptually simple. The objective, in most environmental analyses, is to determine the number of asbestos fibers per unit area or volume in a sample. The sample may be a consumer product, an ambient air sample, or a water sample. This determination is complicated by several factors including sample collection and preparation, counting techniques, and the operational definition of asbestos in use. Three different definitions have been used in the study of environmental samples; these are summarized in Table 1. [ ]

Jan 1, 1979

By Craig M. Sams

Matching mill? drives to mill power draws is a relatively new practice with the introduction of variable speed drive arrangements. Semi-autogenous grinding (SAG) mills are the focus of this paper as ball and rod mill characteristics are easily charted as charge loading and speed change. In addition, a look at types of drives available in the market and mechanical ratings is outlined to match the specifics of each drive.

Jan 1, 1991

By S. Chatterjee

Mining represents the first industry in the United States to have federally mandated training for its workers. Although the topics to be covered are specified in 30 CFR 48, course content is left to the discretion of the individual mine operators. Unfortunately, certain topics to be covered, such as prevention of accidents, are usually mine specific, making it very difficult to use the same course content in every mine. Further, training requirements may change from one mine to another, due to changes in the demographic characteristics of the workers, or changes in job and organizational characteristics. Therefore, if the intention of safety training is to modify the behavior of workers, it is expected that there should be some changes in the content of safety training programs in order to address the specific requirements of individual mines, or at least mines of similar worker and job characteristics. This study has been directed towards the development of a systems-based procedure for conducting a needs analysis. A special effort was made to understand the psychology of worker behavior by analyzing worker reactions to various organizational and job characteristics.

Jan 1, 1994

By L. Patts, J. Rohrbaugh

The Mine Safety and Health Administration (MSHA) has received several reports of filters igniting when high-temperature disposable filters were used on non-cooled diesel exhaust systems in underground coal mines. Based on laboratory testing (to determine the ignition temperature of these filters, which were loaded in the field with diesel particulate matter, or DPM), MSHA determined a maximum safe operating temperature for high-temperature disposable filters. When the results of the laboratory filter ignition testing were reported to the Coal Diesel Partnership (comprised of members of the Coal Industry, Labor, NIOSH and MSHA) the Partnership charged NIOSH with investigating the safe use of high-temperature disposable filters. This paper reports on the design, fabrication and testing of a unique exhaust gas cooling device and the ability of this device to successfully lower filter inlet temperatures and thus reduce the potential for fires.

Jan 1, 2009

By R. C. Gilmore, S. A. Lolon, G. E. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Gob ventilation boreholes (GVBs) are widely used in underground coal mines for longwall gob degasification purposes. GVBs are often drilled within 10 to 30 m above the top of the coal bed into the fractured zone, completed with 20 cm (8 in.) diameter casing and 60 m of slotted pipe at the bottom. The purpose of this completion strategy is to create a pressure sink to capture the emissions before they can enter into the underground workplace. For GVBs to work effectively, they must be drilled close enough to the working areas to capture methane from the fractured zone while the setting depth must be kept above the caved zone to minimize the amount of ventilation air that is drawn into the GVBs. Well completion parameters are important for creating safe working conditions. In this paper, computational fluid dynamics (CFD) studies will be presented to analyze the effect of different practices for GVBs completion parameters for methane extraction, formation of explosive gas zones in the gob and methane concentrations at the longwall face and tailgate. Authors have identified the optimum completion parameters for GVBs, which can maximize the benefit and minimize fire and explosion risk. INTRODUCTION Coal mines may be considered gassy based on the presence of CH4. Gas from the mined coalbed or from rider seams above or below the mined coalbed can migrate into the gob and then potentially move towards the working areas. In longwall coal mines with high methane emissions, sufficient ventilation and additional methane control measures are usually required to reduce the methane concentration in working areas to below statutory levels. Several techniques or combinations of techniques are available to control the methane hazard. These may include mine face ventilation to dilute methane, coal bed degasification, nitrogen injection into the gob to render a methane atmosphere inert and the use of gob ventilation boreholes (GVBs). Longwall face ventilation and dilution alone can only handle methane emissions up to a certain amount. When methane emissions exceed the face ventilation capacity, additional control measures are required. Drilling horizontal or vertical methane drainage holes into the coal seams as well as gob ventilation boreholes from the surface into the gob area to extract methane are common practices. GVBs are usually drilled from the surface above the longwall panel ahead of mining. When the face moves outby the GVBs and the gob begins to form, methane production starts from the boreholes. It is important to control the performance of GVBs to maintain a safe working environment in the mine. The performance of GVBs depends on multiple factors, including borehole location, length and diameter of slotted casing, setting depth of casing above the coal seam being mined, wellhead vacuum pressure, and permeability of caved-fractured zones."

Jan 1, 2016

By William Gleason

"Modern society demands much more from the mining industry than just the raw materials it produces. In addition to providing copper, gold, coal and other minerals that make society function, the industry must conduct its operations in a safe and environmentally sustainable manner. This includes the equipment used and the engines that power the machines.In the United States, Tier 4 diesel engine standards that were set by the U.S. Environmental Protection Agency (EPA) are the strictest emissions requirement for off-highway diesel engines. This requirement regulates the amount of particulate matter (PM) and nitrogen oxides (NOx) that can be emitted from an off-highway diesel engine. In Europe, the Euro V standards are driving technology advancement in the sector.The European Euro V standards are required for new equipment manufactured beginning in January 2019. U.S. Tier 4 standards for heavy-duty off-road engines came into effect with model-year 2014 vehicles and equipment. China 6 standards come into effect in July 2020. India’s Bharat Stage VI standards will take full effect in 2020, and the phase-in of BSVIcompliant clean fuels began in April 2018.Caterpillar, Cummins and MTU are three of the leading manufacturers of engines for the mining sector. Each company is working toward creating efficient engines that can function in the often harsh environments found at openpit and underground mines around the world. In short, society is placing demands that are challenging engine manufacturers to deliver a product that can do more work while consuming less fuel and emitting fewer emissions.Technologies range from selective catalytic reduction (SCR) and diesel particulate filters (DPFs) to other engine strategies and emissions control technologies, which deliver near-zero black carbon and nitrogen oxide emissions, and lower greenhouse gas emissions. Caterpillar’s investmentCaterpillar, the world’s largest producer of mining equipment and mining engines, has been at the forefront of the changing demands placed on the industry and has remained on the cutting edge of engine development over the years, thanks to its investments in the sector.“Caterpillar made the choice to fund major engine and machine development work — even during a deep trough in the mining industry — so that Cat machines would meet Tier 4/EU Stage 5 mandated compliance dates of Jan. 1, 2018 / Jan. 1, 2019, respectively. For Caterpillar, these efforts enabled our mining trucks to provide improved engine component life to help our customers’ total cost of ownership (TCO) and produce a neutral TCO compared to our Tier 2 products,” said Jeff Castleman, new product introduction manager, large mining trucks for Caterpillar."

Aug 1, 2019