Search Documents

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By Asa Weber

With continuing pressure from stockholders not only to maintain but to increase mineral revenues, producers have increased plant capacity. Depressed mineral prices have accentuated the trend toward higher production rates to maintain consistent cash flow, and these same trends have promoted the development of large-scale processing equipment. In addition to the need to handle increased throughput, larger flotation equipment can result in decreased capital-equipment and operating costs. The development of larger column and conventional flotation equipment relies, in part, on suitable scale-up procedures. To properly scale-up large flotation cells and columns, certain constraints and design parameters must be taken into consideration, including velocities in the vessel, residence time, solids suspension, and lip loading. This paper will review the design constraints and scale-up criteria for WEMCO® flotation cells. Scale-up criteria are augmented with computational-fluid- dynamics analyses and high-speed imaging techniques, as well as multiple regresesion analysis of in-plant operational data.

Jan 1, 1999

By Theodore H. Eyde

The porphyry copper province of the southwestern United States and northern Mexico, is the largest copper producing region in the world. Most of the deposits occur in Arizona which now produces over 54% of the newly mined copper in the United" States. As the many recent discoveries are brought into production, Arizona's share of the nation's copper production will increase. The term "porphyry copper" as used in this paper includes all deposits of generally low grade disseminated copper mineralization amenable to bulk mining techniques. Therefore, copper deposits such as Pima-Mission, Twin Buttes, and Vekol where the copper mineralization occurs principally in the intruded rocks will be considered as "porphyry copper" deposits. Most of the deposits have been discovered since World War II, consequently, the southwest, and particularly southern Arizona is perhaps the most intensively explored area for copper deposits on earth. Most of the major natural resource companies in the United States and Canada maintain exploration offices in southern Arizona. To illustrate the success of exploration efforts, the location of porphyry copper deposits either known or producing prior to World War II are shown on figure 1 and the deposits discovered since World War II which are either in production or in the exploration and development stage are shown on figure 2.

Jan 1, 1973

By A.M. Wala

A new radioactive tracer method to measure airflow in inaccessible airways has been developed for situations when studies of the mine ventilation system are not possible using conventional flowmeters (anemometers). The new method has been tested in the ventilation laboratory at the University of Kentucky and in the Experimental Underground Coal Mine at the U.S. Bureau of Mines. This new tracer method has been utilized in leakage, dilution and flow velocity measurements in laboratory and field (mine) experiments.

Jan 1, 1996

By C. William Parisi

Since the introduction of mechanical mining, some 35 years ago, a great deal of effort has been expended by the coal industry to solve the coal dust problem. The original concern was the possibility of a dust explosion or the propagation of a gas ignition; however, in recent years it has come to be recognized as a possible 'health hazard as well. In the middle thirties, the Pittsburgh Coal Company began an intensive study of the dust problem to determine the dust levels created by the various cycles of operation in mechanical mining and to make a comparison with those of hand loading operations. Numerous dust samples were collected with a midget impinger and it was found that dust counts varied from 38 to 268 million particles per cubic foot during hand loading and from 96 to 227 million particles per cubic foot during mechanical loading. The study indicated that the source of underground dust in coal mining could be classified as primary or secondary. A primary source is one associated with appreciable degradation of size, that is, where most of the fines capable of becoming air-borne are produced. A secondary source is one in which most of the fines have been produced at some previous operation and are in such condition that they can become air-borne. Cutting, drilling and blasting are the operations which produce the primary dust. Secondary dust is formed by operations which include; loading, transportation and discharge at transfer points. The study showed clearly that the coal cutting operation was responsible for the greatest amount of dust and that the amount of dust produced varied directly with the speed of cutting; type and dullness of cutting bits; and the distance the cuttings had to fall to the floor. The information obtained from the study enabled our company to decide on a course of action and the direction to follow. With the cooperation of mining machine manufacturers, water tanks with a 200 gallon capacity were built into the machine trucks and were provided with a pump driven by a small motor. A length of 1/2" water hose carried the water from the pump to the two water spray nozzles located at the front of the machine. Water was delivered to the machine tanks by water cars which were filled on the surface or from an underground water supply. It was during these early days that wetting agents were introduced into the water system. Our studies revealed that wetting agents did little better than plain water in the abatement of the dust problem. It was found that when using a wetting agent less water was required to obtain the same results but we could not take advantage of this fact because it was almost impossible to keep the smaller nozzles open to reduce the amount of water being used.

Jan 1, 1967

By George E. Edwards

Pacific Rim markets for export coal already represent a larger market than the total tonnage imported into the European Community countries and they will continue to expand. The largest importers will continue to be in the sector comprising Japan, Korea, Hong Kong and Tai- wan. It is likely that the total Pacific Rim markets will reach 206 m.t.p.a. by 1990 and 290 m.t.p.a. by 2000, with the major growth in steam coal demand. Australia has an efficient coal industry, represents a stable long term source of supply and is favourably situated geographically to continue to be the largest single supply source.

Jan 1, 1982

By Will B. Jamison

The most serious safety problems encountered in U. S. underground coal mines today are related to the roof bolting operation. Also, roof bolting is usually the operation which limits coal production of the section. The purpose of my paper is to review some of the research, developments, and new ideas related to roof bolting. Many of these ideas have originated at. coal mines or with manufacturers. Most of the research on fundamental improvements has been funded by, and is a part of, the excellent and broad plans of the Bureau of Mines.

Jan 1, 1977

By Dave G. Osborne

With the growing exportation of coal from North America to the Pacific Rim countries and Europe, has come an increasing awareness of the need to determine economically optimized amounts of incombustibles (ash and moisture contents) for the shipped product. Despite the fact that demand bas caused a steady improvement in selling price, particularly for thermal coals, growing production and transportation costs have compelled producers to keep a sharp eye open for ways and means of minimizing the latter since this probably represents the greatest single potential for making savings. Consequently the Coal Industry has become acutely aware of the economic ramifications of eliminating moisture in particular, thereby producing further saving in the cost of transportation of product from the mine to the consumer. There is, however, a lower limit to which dewatering or drying can be taken and this relates to dustiness which is a function of the characteristics of the coal and the methods used for handling and storage during trans-shipment. Overdrying can lead to serious dust losses and difficulties in handling particularly if the coal contains a large proportion of fines. The ways and means for achieving this "happy medium" of optimization in moisture removal are seemingly undergoing gradual modification largely assisted by the following factors. a) Improvement in effectiveness of coal dewatering and drying equipment. b) Improvement in operational availability and utilization of the equipment. c) The development of surfactants, polymer flocculants and other agents which in many cases can be almost tailor made to suit specific applications.

Jan 1, 1982

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

By Hassan El-Shall

Treatment of plant effluent including waste water and associated soluble and insoluble substances, is of a primary concern of many process industries including mineral processing operations. The major objective of such treatment is the removal of such impurities which can interfere with the process through the use of recycled water, and/or to comply with environmental ordinances. For example, Ramirez and Clements (1978) state that molybdenum contents in the range of 19 mg/1 eventually poison ion exchange resigns used for the extraction of uranium. In addition, recent restrictions by the EPA on molybdenum discharge values for mining waste water necessitate removal of this metal to (0.5-1.0 mg/1).

Jan 1, 1984

By W. D. Hausel

The Wyoming Province is an Archean craton which underlies portions of Idaho, Montana, Nevada, Utah, and much of Wyoming. The cratonic block consists of Archean age granite-gneiss with interspersed greenstone belts and related supracrustal terranes exposed in the cores of several Laramide uplifts. Resources found in the Province and in the adjacent accreted Proterozoic terrane include banded iron formation, Au, Pt, Pd, W, Sn, Cr, Ni, Zn, Cu, and diamonds. The Province shows many similarities to the mineral-rich cratons of the Canadian shield, the Rhodesian and Transvaal cratons of southern Africa, and the Pilbara and Yilgarn blocks of Western Australia, where much of the world's precious and strategic metal and gemstone resources are located.

Jan 1, 1991

By Roy H. Paddon

This paper describes the 6, 000 tpd, three stage haulage system at the Ozark Lead Company's mine in southeastern Missouri. It details the methods and problems pertinent to the loading, hauling, sorting, crushing, storing and hoisting of waste rock and ores obtained from underground development headings and production areas. The Ozark Lead Company is a wholly owned subsidiary of the Kennecott Copper Corporation. Its mine is located nine miles south of Bunker in Reynolds County at the south end of the "New Lead Belt" mining district. Development started in May, 1964, by drilling a seven foot diameter (six foot cased), 1, 250 foot development-ventilation shaft. Drifting began in August, 1965, to obtain a bulk ore sample, to test ore continuity, and to drive two mine levels while the pre-grouted production shaft was being sunk. Over 7, 900 feet of 12 by 24 foot drifting was done from this small shaft. In March, 1966, a 20 foot diameter, three compartment, concrete lined production shaft was collared. It intersected existing development headings at a depth of 1, 195 feet in April, 1967, and was completed along with a concentrator and other facilities in June, 1968. Mine production began that month, with 5, 000 tpd reached in 1970.\

Jan 1, 1971

By Zhiguo Chang, QINGXIANG CAI, Ebelia Manda, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, Saleem Raza Chalgri

The concept of mine safety is highlighted in the literature of sustainable mining but not extensively discussed. This study analyzes various aspects of underground and surface mine safety and emphasizes its importance in the context of sustainable mining. More specifically, this research attempts to find the relationship between mine hazards and demographic characteristics, examine and compare the perceptual difference among miners, and determine the impact of mine hazards on workplace safety and safety climate. Descriptive analysis, chi-square test, independent samples t test, and linear regression modeling were conducted to achieve study objectives. Results confirmed that mine hazards were significantly associated with age and experience. Miners perceived lower levels of management safety practices, followed by supervisor safety, coworker safety, and job safety. The analysis showed that underground miners reported lower safety scores than surface miners. There was a statistically significant difference between miners’ perception of safety climate (p < 0.05). The results showed that the higher prevalence of mine hazards predicts poor workplace safety and a low safety climate. The regression models revealed that mine hazards have a significant effect on workplace safety (p < 0.05) and safety climate (p < 0.05). In conclusion, the distinctive model of mine safety presented here contributes to the monitoring and design of comprehensive safety interventions and helps to better understand how certain factors interact on multiple levels to influence the overall safety of the industry. In this study, some suggestions are put forward to provide directions to develop a sustainable mine safety system.

Mar 27, 2020

By J. L. Thompson

Lime made in a coal-fired, rotary kiln has two distinct parts: the interior of the pebble which constitutes about 90% to 95% of the mass, and the surface dust layer which is the remaining 5% to 10%. Uncalcined carbonate and impurities in the product may be present and will not contribute to the hydration reaction. Sulfur, in the form of calcium sulfate, inhibits the hydration reaction out of all proportion to its actual weigh-percent concentration (perhaps more than 100 times). If the stone contains dolomite, this will also inhibit the reaction as its rate of hydration may be nearly 3 orders of magnitude slower than that of calcium oxide. Early in the hydration reaction dolomite appears practically inert, but given sufficient time, it will hydrate. The heat of reaction is nearly the same as for calcium oxide, but the time necessary for complete hydration may be hours; whereas for calcium oxide it is only fractions of a second. The dust layer on the surface also inhibits hydration as it contains a collection of compounds which have low heats of hydration. This layer can tie up additional calcium and delay or prevent its reaction. In addition to these chemical processes, an important physical characteristic of the lime is its specific surface area. This is effected by the thermodynamics of calcination and the original stone grain chemistry. All of these factors are agglomerated in the gross slaking rate of lime. The total hydration of the chemical complex that is called commercial lime can be more easily understood by considering the individual reactions and combining them to form a more comprehensive picture of the situation. Calcium oxide and magnesium oxide hydrate similarly, differing only in their reaction kinetics. Dolomite, however, reacts differently than a simple mixture of calcium oxide and magnesium oxide as its hydration is strongly influenced by calcination thermo-dynamics and stone grain structure. Finally, the dust hydration and composition should be examined Understanding these reactions enables one to examine hydration reaction graphs with more insight into the factors which determine their shape.

Jan 1, 1978

By Evan Dressel, Mark S. Diederichs, Kathy Kalenchuk

As hard rock mining develops deeper over time, there is an increasing need to predict the spatial and temporal distribution of adverse seismogenic rockmass reaction to mining. Real-time monitoring and feedback of mine data are used to tactically manage risk associated with induced-seismicity; however, strategic risk management requires reliable tools for forward predictions of seismic hazard. The forward prediction of seismic hazard is strengthened by understanding of potential seismic intensity, which often relies on well calibrated mine-wide numerical models. This paper uses a case study to explore how future seismogenic potential and the nature of future seismicity can be domained according to numerically predicted stress-strain paths at past seismic event locations. Delineation of high confinement seismogenic volumes vs. lower-confinement, high-strain seismogenic volumes at the mine-scale can be achieved, based on a loading and unloading stress path analogue, to refine understanding of seismic intensity. Practical qualitative and quantitative methods to achieve this delineation will be demonstrated. Once seismogenic mode (high-stress vs. high-strain) is identified, detailed analyses of seismic source parameters demonstrates change in seismic hazard between the domained volumes.

Apr 26, 2022

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By V. E. Gall, A. Vonthron, J. Ninic, A. Marwan, M. König, G. Meschke, A. Alsahly

"In current tunneling practice, finite element simulations have become an integral element of the planning and design process. These models are most often manually generated using 2D CAD drawings, which is a laborious and time consuming process. In this paper, we propose a BIM based approach, in which the 3D FE-model is automatically generated through a set of compatible geometries of individual components, i.e. the geology, alignment, lining and the TBM. The BIM model also includes all relevant model parameters of the tunneling project that can then be incorporated into subsequent analysis to be performed during the tunnel drive. The setup and the execution of the FE-analysis are performed automatically utilizing all required data from BIM. The applicability and efficiency of the proposed strategies is demonstrated by means of project data from the Wehrhahn-line metro project in Düsseldorf, Germany. Both the design as well as the construction stage is considered. INTRODUCTIONIt is recommend to employ Finite Element (FE) simulations in order to ensure a high degree of safety and quality for any given project (Guglielmetti et al. 2012). As such, FE models form an integral part in the design and planning stages of modern tunneling projects. These models are often time consuming to construct and require data from many different sources. This data is most often not centrally stored and therefore not easily accessible. Additionally, the formats in which project data are stored are typically not compatible with the formats required by an FE program. This is especially true in the case of geometrical data, such as CAD drawings. Although existing design drawings are most often used as the basis for a FE model, a direct import into a FE program is most often not successful as the imported data generates a geometry that does not fulfill the requirements of a FEM model, such as model connectivity. Even if a geometry is successfully imported, other necessary aspects of an FE model, such as boundary conditions and material properties, must be applied manually. These incompatibilities inevitably result in the creation of a new model, which, especially in the case of complex 3D models, is a time consuming process."

Jan 1, 2016

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica plate and glass sphere in sodium oleate solutions. Hydrophobic forces were observed when the two surfaces were activated by CaOH+ or MgOH+ ions. The force measurements conducted in the absence of the surfactant showed that the activated silica surfaces do not exhibit the primary hydration forces that have been observed between unactivated surfaces. The activation mechanism was studied by calculating the contributions from electrostatic and chemical interactions to the total free energy change. The results suggest that the adsorption of the hydroxo-complexes is controlled mainly by the lateral interactions between the adsorbed species on the silica surface.

Jan 1, 1999