Search Documents

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By M. A. Gibson

Ilmenite-rich lunar deposits can be converted to liquid oxygen to support lunar base operations and space transportation propulsion needs by a Carbotek-developed process. Iron oxide in ilmenite is reduced at elevated temperatures by hydrogen in a fluidized-bed reactor to water vapor which is electrolyzed to product oxygen and recycle hydrogen. Reaction rate, thermodynamic equilibrium, and lunar-gravity fluidization behavior are key factors which have been considered. Fluid-solids behavior has been modeled from data taken at lunar gravity conditions aboard NASA KC-135 flights. Large-scale pilot plant operations are planned to complete the development.

Jan 1, 1991

By Steven E. Paulson

In situ mining is emerging as a potential alternative to conventional surf ace and underground mining techniques. A major factor in determining recoveries by in situ mining is the proportion of ore minerals that can be contacted and solubilized by the leach solutions. To provide basic information on the processes occurring during in situ leaching, particularly at the microscopic scale, the Bureau of Mines has developed a geologic characterization research program. This includes laboratory experiments using leaching apparatus that can accommodate whole core samples. Whole core experiments result in higher leach solution-ore mineral contact ratios than packed column experiments, and also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels in the rock. A nonreactive, reusable reaction cell has been designed and tested. The leaching apparatus can be used for constant-pressure or constant-flow experiments and allows for the control of flow rate, pressure, and temperature during the experiments, thus permitting studies on a wide variety of ore samples. Details of the experimental apparatus and design are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grande, AZ, area.

Jan 1, 1987

By A. M. Esteves

This paper addresses the question ?What constitutes the right level of investment in community goodwill?? Mining companies are still grappling with this subject even though the business case for community investment has been accepted at a general level, as a strategy for competitive differentiation, risk mitigation and a desire to deliver - and to be seen to deliver - a ?net benefit? to affected communities. Gaining senior management commitment to long term social projects, by definition characterized by uncertainty and complexity, is made easier if projects are shown to benefit the site?s strategic goals. Case study research amongst mining companies, including interviews with social investment decision-makers, has assisted in developing a SI-DAT (Social Investment Decision Analysis Tool), a decision model for evaluating social projects in order to create value for both the company and community. Multi-criteria decision analysis techniques integrating business planning processes with social impact assessment have proved useful in assisting mining companies think beyond seeking access to required lands and peaceful relations, to how they can meet their business goals and contribute to regional development.

Jan 1, 2007

By J. L. Watson

n the U.S., lead has been produced via blast furnace processing for over a century, and the slags from that pyro-metallurgical process have been accumulating on industrial sites over that extended period. Lead blast furnace slags typically contain both lead and zinc compounds in an iron-silicate matrix, and it appears highly likely that such materials will have to be processed in the near future to meet with EPA regulations. Thus it is appropriate to investigate possible processing routes to render the slags non-hazardous and simultaneously to recover metal values to partially off-set the inherent high cost of processing such materials. There are two major processing alternatives: one being pyrometallurgical and the other hydrometallurgical. The research reported here investigates leaching/solution purification/recovery processes for lead and presents experimental data for the treatment of lead blast furnace slags from S.E. Missouri. The results of the research suggest that both lead and zinc can be removed effectively from the slag, and that metallic lead can be recovered directly from the organic extractant utilized for solution purification.

Jan 1, 1995

By J. A. Harrison

Most coal being used in the United States has been subjected to one or' more processes of coal preparation. The physical and chemical characteristics of a coal have a marked influence on the ultimate uses that coal may have. The selection of the proper preparation processes may similarly be important in producing the best practical coal product for any particular use. The physical composition and distribution of physical constituents in the coal will partially determine the efficiency of the preparation process chosen and conversely distribution and concentration of coal macerals will, to a degree, be controlled by the preparation process. A number of preparation processes have been evaluated to determine this interrelation. If a coal having' certain specifications is desired, these evaluations trill assist in providing information needed for the production of this coal.

Jan 1, 1962

By L. B. Rothfeld

In anticipation of RCRA reauthorization and subsequent rulemakings, the Bureau of Mines is studying potential economic impacts of RCRA on mining. For U.S. copper heap and dump leaching operations in a variety of terrains, the cost of liners and closure caps to comply with RCRA Subtitle D ranges from $55 million to $158 million per site, or about $500,000 per hectare ($200,000 per acre). If RCRA technology requirements and financial assurance had been required on current operations, 27 to 100% of production from heap and dump leaching would have been non-competitive at market prices between $2,310 and $1,650 per metric ton ($1.047 and $0.75 per pound) copper. This result is based on an analysis that considers return on capital, corporate overhead, marketing, and freight costs as well as operating and maintenance costs at the mine. Over the same price range, economic analysis using the IMPLAN input-output model on one-or two-county regions indicates potential net job losses of about 570 to 2,700 jobs. Total economic output of those counties could be reduced by about $180 million to $360 million.

Jan 1, 1994

By C. Bryce

Rhenium is primarily recovered as a byproduct from molybdenum roasting circuits. However, rhenium is also present in copper heap leach solutions at very low concentrations, and this represents a potential new rhenium source. Freeport-McMoRan (FCX) has developed a new process using carbon adsorption followed by ion exchange or solvent extraction to concentrate rhenium from less than 1 ppm to 15 g/L. The product is compatible as a feed to an existing rhenium processing plant. A pilot plant operated at Freeport-McMoRan?s Sierrita Mine has demonstrated the technical and financial feasibility of this new process. Copper heap leaching dissolves more than just copper from the copper ore. Several metals can be identified in leach solutions at concentrations of financial interest, rhenium in particular. Rhenium spot prices ranged from a yearly average of $1,070/kg ($483/lb) in 2005 (Magyar, 2008) to $10,400/kg ($4,706/lb) in 2008 (Polyak, 2013). The spot price in September 2013 was approximately $3,000/kg ($1,357/lb) of rhenium (Metal Bulletin, 2013). Several facilities at Freeport-McMoRan have very low rhenium concentrations in their copper leach solutions, ranging from 0.1 to 0.7 mg/L. The large quantity of solution available, if coupled with an attractive rhenium price, means that the rhenium contained in leach solutions may represent a significant value if a method of extraction could be developed. Testing has confirmed that rhenium adsorbs onto activated carbon much more selectively than other metals in the pregnant leach solution (PLS). A 100-gpm pilot plant was constructed to verify the lab-scale results on a larger basis and establish operating parameters for a full-scale operation. This report summarizes the initial technology development and pilot plant operation.

By T. W. Camm, J. C. Johnson, S. D. Rosenthal

"Most engineers are bright, hard-working, reliable and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But, is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this article will look at some common misconceptions about leading engineers.Engineers are different. There, it has been said. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot of individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for.Clash of culturesWhat distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain. Standards are maintained both through peer review and in academia, through ABET accreditation and through professional associations like SME to promote the discipline and foster technical growth.Six characteristics representing professional status are described by Raelin (1985, p. 9):• Expertise — prolonged specialized training in a body of abstract knowledge.• Autonomy — the freedom to choose the means to solve a problem.• Commitment — primary interest is in pursuing the practice of one’s own chosen specialty.• Identification — identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization.• Ethics — providing service without concern for oneself or without becoming emotionally involved with the client.• Standards — committed to help in policing the conduct of fellow professionals."

Jan 1, 2018

By V. Russel Burkhart

One of the most difficult items to justify economically on any budget is a training program. The costs can easily be identified--primarily the cost of the program and the inconvenience and cost of filling in for the men taking the training by working other personnel extra hours at overtime rates. Operating efficiency, higher productivity, increased plant availability, development of confidence, improvement in morale and less absenteeism are only a few of the benefits which far exceed the costs. A good preparation plant training program can accomplish more in 5 weeks than can be accomplished in five years of on-the-lob operation. During recent years, coal preparation plants have become more sophisticated and complex as the specification for coal used by electric utilities in their power plants have required improvements in coal quality to adhere to air quality regulations and to improve boiler performance and reliability.

Jan 1, 1981

By T. D. Parris

At the Frood Mine of International Nickel, tests were begun in March 1966 to evaluate the use of low profile diesel Load- Haul-Dump equipment in cut-and-fill operations. In December 1966, this test was extended to drawpoint loading of caved ore at the Creighton Mine. The results of these tests conclusively demonstrated the effectiveness of this equipment in the operations at International Nickel. This paper describes the equipment used, the operation of the equipment, production data and operating details. Also discussed in the paper are other trackless equipment which works with the Load-Haul-Dump carrier. Production and Safety comparisons are made with the slusher method in bulk mining, giving the reasons for replacing the slushers at the mines of International Nickel Company of Canada, Limited, Ontario Division.

Jan 1, 1969

By A. F. Grandt

What is prime farmland? Can such land, once it has been strip-mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on strip-mined land in St. Clair County (1). This research was done almost 30 years before requirements of Public Law 95-87 were passed by the United States Congress and signed August 3, 1977.

Jan 1, 1980

By B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand and gravel (SSG) sector in the United States. Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) are conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine.

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom-designed radial sector sampler , six large blasthole samples were collected to perform the test developed by Pierre Gy to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to total fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32 percent and ±49 percent for copper and molybdenum, respectively. A classical statistical analysis conducted on the data confirmed the level of RSD native to the mine. About 95 percent of the sampling error was produced from one step in the sampling protocol, that of reducing the 1-kg (2.2-lb) sample to a 50-g (0.1-lb) sample for chemical analysis. To minimize the FSE, the use of a slightly different protocol is recommended. The 1-kg sample (2.2-lb) should first be crushed to a 0.2 cm (0.08 in.) particle size. A 250-g (0.5-lb) split should then be taken and finely ground, from which a 50-g (0.1-lb) split should then be taken. These simple steps will reduce the FSE to ±7.9 percent and ±17 percent for copper and molybdenum, respectively. The modified sampling protocol effectively reduces to zero the probability of misclassification of low-grade ore. IntroductionThe Erdenet copper-molybdenumopenpit mine is located in Erdenet in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is 1.5 to 3 km (0.9 to 1.8 miles) wide and about 25 km (16 miles) long (Erdenet Mining Corp., 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 Mt/a (29 million stpy) of ore."

Jan 11, 2017

By Roland Trunk, Marcel Imbach, Yves Boissonnas, Jan Vesely

"INTRODUCTION The expansion of the Suez Canal, which runs between the Mediterranean and Red Sea, is at the top of Egypt’s economic agenda. The £8 billion development plan includes a new channel alongside the existing one which will double the number of ships able to pass each day and several tunnels to connect the Sinai peninsula to the main part of Egypt. The Egyptian government ordered three new tunnels under the Suez Canal in the area of Port Said as part of the Canal Region Development Plan. The three tunnels will contribute to the North Sinai expansion, helping to create a vast industrial zone and completing the coastal road extension from Rafah to Nuewiba. Two of these three tunnels will be allocated for roads and the third for railway traffic. A further part of the Suez Canal development mega project are an additional six tunnels in the area of Ismailia and Suez. The focus of this paper is on the two road tunnels in Port Said and will give an overview of the project and the challenges encountered regarding the technical complexity and tight time schedule both in its design and execution. PROJECT OVERVIEW The tunnels will be built in the area of Port Said (see Figure 1) which is the most northern part of the Suez Canal.The road alignment connects the Port Fuad Road in the east bank of the Suez Canal to the Port Said-Ismailia highway in the west bank with a dual carriageway section. Each of the carriageways has two lanes. The bored diameter of the 2.8 km long road tunnels is 13.050 m and will be driven with two Mix-Shield TBMs. The distance between the two tunnel axes is planned with 42.5 m (discussion about a reduction are ongoing). The width of the Suez Canal is around 340 m at upper level and around 170 m at the bottom. During the TBM drive, three main geological layers are expected. Below a depth of around 40 m in a very soft clay layer, a dense to silty sand layer is predicted. Within the sand layer another silty hard clay is expected in different depths with variable thickness. After finishing the excavation of the road tunnels, the same TBM will be used for the railway tunnel. The lowest points of the road tunnels will be located 59 m below the surface (tunnel invert to surface) and only 18 m of ground cover exists between the tunnel crown and the Suez Canal invert. Minimum ground cover over the tunnel crown is approximately nine meters at the tunnel portals."

Jan 1, 2016

By Peter W. Scott

Feldspars have major uses in glass manufacture and in ceramic products. About 6 million metric tons (6.6 million short tons) are used annually. Feldspars are desirable because of their high aluminum and alkali contents. Na feldspars are favored for glass, while K feldspar is often preferred in the pottery and tile industries. Economic deposits occur in a variety of geological environments. Most are in granites or granite-like bodies, pegmatites being a common source worldwide. Alkali granites, particularly those some- times called alaskites, are mined directly as a source of feldspar and associated minerals. Some other igneous bodies, such as aplites, rhyolites, and partly altered granites (for example china stone) provide alternative feldspar-rich products. Nepheline syenites and phonolites are other sources of feldspar and contain higher amounts of alkalis. Feldspar-rich (arkosic) sediments derived from the weathering of pegmatites and granites are widely extracted and processed for use in ceramics. The present study reviewed the various sources of feldspars throughout the world. Data on the quality of products has been taken from literature, and samples have been obtained from a large number of producers. The mineralogy and chemistry of the samples has been determined and, as far as possible, have been related to the geology of the source area. Feldspar products show a wide range of chemical and mineralogical compositions. Some are pure Na feldspar (albite), others are made up entirely of K feldspar (microline and orthoclase), but many are mixtures of Na and K feldspars. Significant quantities of quartz are often present, and many products contain mica and kaolinite. Fe203 con- tents are very low, typically less than 0.1 percent. Detailed mineralogical studies show that four groups of products can be recognized on the basis of feldspar mineralogy. These are albite, albite with microcline, microcline with orthoclase, and orthoclase with albite. Products containing microcline and orthoclase together are mostly sedimentary in origin. Those with albite only, or albite with microcline have a pegmatitic or granite origin. Those containing orthoclase as the dominant K feldspar are derived from aplites or rhyolites. There does not appear to be any relationship between the feldspar mineralogy and the quartz content. Peraluminous S- type granites and pelite-dominated high-grade metamorphic rocks, in which there is a significant volatile component, are likely to be the most important feldspar sources. Partial kaolinization of feldspar-containing rocks often improves minability, decreases crushing costs, reduces iron content, and increases the K2O/Na2O ratio.

Jan 1, 2001

By Rebecca Boakye, Zohreh Kazemi Motlagh, Virginia T. McLemore

The most significant uranium (U) deposits in New Mexico are sandstone-hosted deposits in the Morrison Formation (Westwater Canyon Member), where >169,500 short tons of U3O8 were produced from 1950 to 2002. In addition, >9076 pounds of vanadium (V, a critical mineral) and some molybdenum (Mo) were produced from these deposits. These and other U deposits (limestone-hosted, U-veins) in New Mexico also contain critical minerals. Critical minerals are mineral resources that are essential to our economy and whose supply may be disrupted; many critical minerals are 100% imported into the U.S. Some sandstonehosted, limestone-hosted, and U-vein deposits are elevated in heavy rare earth elements. One sandstone-hosted sample contained 0.3 ppm Re (critical mineral), 659 ppm Se and 408 ppm Mo. The arsenide five-element vein deposits in the Black Hawk district are mineralogically and texturally complex, low- to moderate-temperature, hydrothermal, structurally-controlled, Ag-Co-Ni-Bi-As bearing carbonate vein systems with local minor elements. Mineralized samples from Black Hawk contain up to 9970 ppm Ag, 8540 ppm As, 5690 ppm Co, 72,400 ppm Ni, 57 ppm Bi, 165 ppm Sb, and 32,600 ppm U.

Feb 22, 2026

By B. V. Clingan

A practical application of recent design concepts makes it possible to design a column cell to fit a specific set of conditions. The design and operating parameters Of a column cell installation that replaced a conventional two stage copper flotation cleaning circuit at MAGMA COPPER COMPANY, SAN MANUEL, ARIZONA using these design concepts is described. A survey of other mineral processors using column cell technology was conducted. The results of this survey will also be discussed.

Jan 1, 1987

By K. Osseo-Asare

LIX63 in combination with DNNS selectively extracts nickel and/or cobalt from acidic leach liquors with pH values as low as 1.0. Nickel/cobalt and cobalt/nickel selectivities are achieved by varying the relative concentrations of LIX63 and DNNS. Increasing LIX63 concentration retards both extraction and strip-ping rates while DNNS has the opposite effect. Slope analyses of equilibrium data indicate that both LIX63 and DNNS are present in the extracted complexes. Examples of possible flowsheets are presented.

Jan 1, 1978

By J. P. McDonald

Exposure to particulates containing metals and metal fumes (PCMMF) is a potential concern in ore refining and smelting. Some metals of primary interest are arsenic, cadmium, copper and lead, which have been linked to various adverse health effects. The current National Institute for Occupational Safety and Health (NIOSH) sampling method for metals in particulates requires the use of a filter, precision airflow pump and laboratory analysis. A major concern with this method is the one-to-two weeks? wait before laboratory results are available for use in determining if additional controls are needed to assure adequate exposure protection for workers. Particulates containing these metals were sampled during sixteen sampling events at a copper smelter using the traditional NIOSH methods. Monitoring of particulates was simultaneously conducted using a TSI 8520 Dust-Trak real-time aerosol monitor with a 10-µm-cutpoint sampling inlet. NIOSH analytical methods related to particulates and metals (methods 0500, 0600 and 7300) were used to determine particulate mass and individual mass contributions of metals on sample filters. Linear regressions with y-intercepts forced to zero were developed to determine the relationship between the PM10 measurements recorded by the DustTrak and laboratory-reported total particulate mass, PM10 and respirable arsenic, cadmium, copper and lead concentrations. These linear regressions yielded correction factors that can be applied to DustTrak readings to obtain total particulate mass, PM10 and respirable concentration estimates for each of the four metals. The R2 (coefficient of determination) values from the linear regressions ranged from 0.65 for total lead to 0.91 for total copper. These results suggest that the DustTrak may produce real-time data useful in providing estimates for airborne concentrations of arsenic, cadmium, copper and lead in copper smelter particulates.

Jan 1, 2011