Search Documents

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs. Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By M. J. Virnig, Peihao Qi, J. Brent Hiskey

The mechanism of gold uptake from iodide solutions by carbon has been investigated. Adsorption isotherms for gold and iodine were established. For activated carbon, approximately 300 mg of gold and 1000 mg of iodine were extracted per gram of carbon at maximum loading. Examination of loaded activated carbon particles by scanning electron microscopy reveals isolated patches of gold deposited on the carbon surface. High-resolution transmission electron microscopy shows that fine gold particles (1-4 nm diameter) are uniformly distributed within the carbon. Iodine was also observed throughout the matrix. The uptake of gold by carbon from iodide solution involves a combined reduction and adsorption process, where the gold iodide species is reduced to the metallic state superficially and adsorbed in the porous structure of carbon. A few experiments for the gold-chloride and gold-bromide systems were carried out for comparison.

Jan 1, 1993

By H. Ankara

Determining the identicalness levels of the same model trucks working in open pit mine transportation system by means of statistical analysis methods is very significant in terms of availability analysis. In this study, the identicalness levels of two trucks picked randomly from the 170-short-tonne truck fleet working in open pit coal mine over one-year period were examined through a non-parametric test, Mann-Whitney U test for two samples. Time to failures (TTFs) and Time to Repairs (TTRs) of the trucks were analyzed with this test technique and then whether they were identical or not was determined. In order to determine whether the trucks identified to be identical at the end of this test displayed the same mining performances within the same open pit transportation system, the availability analysis of the identical trucks was carried out. As a result of the availability analysis, it was observed that the trucks had availability values that were very close to each other. It was also determined that Mann-Whitney U test could be employed together with availability analysis. Finally, it was observed that Mann-Whitney U test for two samples could yield rapid results in the performance analysis of complex systems like open pit mines.

Jan 1, 2010

By D. Bogunovic

The objective of this research was to conduct field-scale experiments at an operating surface coal mine in order to determine the impact of the bucket fill factor on dragline production rate and energy consumption. Data collected from a dragline monitoring system were recorded in a specifically designed software tool and the relationship among these parameters was established. an algorithm for the determination of the ?best? fill factor was developed and integrated in the software. It was determined for the analyzed dragline in the mine that energy consumption in the digging phase can be reduced by 36% and production rate can be increased by 1.4% for a bucket fill factor of about 80%, a fill distance of 19.8 m (65 ft) (i.e., 3.1 bucket lengths) and a bucket fill time of 15 sec. the method developed and applied in this study may help dragline operators to determine the fill factor that will increase production rates and reduce energy consumption in specific surface coal mines. Mining Engineering, 2011, Vol. 63, No. 8, pp. 48-53. Official publication of the society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By H. Y. Sohn

Considering the two most important issues the ironmaking industry faces today, i.e., energy consumption and greenhouse gas emissions, it would be advantageous to utilize the concentrate-size raw materials directly without pelletizing or sintering, especially without the use of coke. This plenary lecture describes two such processes developed at the University of Utah. One is the Flash Ironmaking Technology (FIT) and the other is a moving-bed process for continuous ironmaking with gaseous reduction of iron ore concentrate (MBIT). These technologies are designed to produce iron directly from iron concentrate without requiring pelletization/sintering and cokemaking in two significantly different temperature ranges. They take advantage of the high reactivity of the concentrate particles and will considerably reduce energy consumption and carbon dioxide emissions compared with the current processes. The process of the development from the conception of the idea, to kinetic feasibility establishment, to laboratory flash furnace, and finally to the operation of a prototype facility for the development of the FIT is discussed. The development of the MBIT also started with the formulation of the process concept, followed by kinetics feasibility establishment, and the design of a potential industrial reactor. The results of economic analyses on the FIT are briefly described.

May 12, 2023

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 established the Office of Mine Safety and Health (OMSH) within NIOSH and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. Subsequently, Congress provided additional funding to NIOSH to initiate and continue the program. OMSHR has fulfilled this Congressional mandate through annual Broad Agency Announcement (BAA) solicitations, directed Requests for Proposals (RFP) and Inter-Agency Agreements (IAA), and has further expanded the program through capacity building BAA contracts with U.S. university mining departments in the areas of mine ventilation and ground control. This paper describes the extramural funding program and broadly examines the results of the 150+ contracts issued to date, grouped into key focus areas. INTRODUCTION The Mine Improvement and New Emergency Response Act (MINER Act) of 20061 established the Office of Mine Safety and Health Research (functioning as the Office of Mine Safety and Health Research or OMSHR) within the National Institute for Occupational Safety and Health (NIOSH), and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued over 150 contracts focused on worker health and safety. Initial funding for this program was provided by Congress through two Emergency Supplemental Appropriations (ESA) and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation; ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website2 and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously.3"

Jan 1, 2018

By B. K. Mishra

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills (14-18 ft). DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important factors such as the configuration of the liner and the geometry of the lifting surfaces are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill with particular emphasis to large diameter mills.

Jan 1, 1992

By T. D. Oulton

The only known attapulgite clay deposits of any considerable extent and purity in the United States are roughly bisected by the Georgia. Florida state line between Decatur County, southwest Georgia, and Gadsden County, northwest Florida. Although attapulgite clay occurrences both farther East and South are known and have been mined to some extent in the past, at the present time it can be said that substantially: all of the commercial attapulgite clay mining and pro¬cessing is concentrated in a roughly rectangular area some 25 miles long by 15 miles wide,, in the general region of Attapulgus, Georgia, and of Quincy and Havana, Florida. Within this area are located the clay processing plants of the four major producers as well as most, if not all, of the currently active mining operations. The approximate location of the plants and of some of the open mines are shown in the local area map, Figure No. 1, for the purpose of orientation only.

Jan 1, 1965

By Julius Rubinstein, Victor Badenicov

The development of column flotation is the most significant achievement in the area of mineral processing in the last few decades. The high efficiency of column flotation allows a reduction in process time, a decrease in the number of cleaner stages and in the volume of the circulating load in the flotation circuit, and, as a result of this, an increase in consistency and reliability of operations. Unique multisectional column flotation apparatuses were developed. Such designs have a number of essential advantages as compared to monocells. A change from monocells to multisectional column allows to provide favourable conditions for separation of particles of various floatability. To attain that aim particular hydrodynamics and aeration regime is established in each section of the column, operational variables being adjusted according to the floatability of the material. Therefore in multisectional column machines the material-apparatus feedback can be established, process variables optimized depending on the characteristics of the floated materials. This concept forms the basis of column designs we have developed. For the first time column cell with alternating slurry Rows (combination of co- and counter-current flows) were developed and commercialized . Successful operation was reported of the new generation of columns with cell volumes of 10 to 80 m3 and the height of 4-6 m in copper, molybdenum, antimony, tungsten and nickel ores and coal slurry processing at different plants. Operation experience of these cells showed their considerable design and operational advantages and verified the proposed options and relationships. The new apparatus is provided with a pneumohydraulic aerator allowing to control bubble size distribution, the service life of the aerator is not less than two years. A multilevel flotation model was developed and used to work out a technique of column design and process parameters calculation. A method of the apparatus design parameters calculation based on laboratory test results (scaling up) was worked out. The method is based on flotation macro and micro-hydrodynamics simulation.

Jan 1, 1995

By Robert R. Unterberger

The purpose of this paper is to summarize the research of the past sixteen years on three distinct methods of probing into solid rock. The first method is to use radar of the appropriate frequency. The second method is to use sonar. The third method is of recent vintage and uses techniques of nonlinear sonar also known as parametric sonar. The first two concepts, that of radar and sonar, are common to most people. Very few have heard of nonlinear sonar. Each of the probing techniques were investigated in order to overcome deficiencies in the former technique. Each has its advantages and disadvantages. It should be emphasized that all of these techniques for probing (or seeing) into rock are used in mines, and generally speaking not from the surface. Only in very special cases, such as certain very dry parts of Egypt or Peru, or, for example, the surface of the moon, will these probing techniques work from the surface. The reason for the development of these probing techniques has been to alert miners to possible hazards ahead of mining. Such hazards may be (1) old (unknown) boreholes connected with high pressure water zones above, (2) fractures that might connect to the Gulf of Mexico above the mine, (3) water-filled fractures that threaten the safety of miners, or (4) the discovery of dry faults ahead that can disrupt the planning of future operations.

Jan 1, 1983

Horizontal stress is an important factor that contributes to roof failure during a long wall entry development, especially when the immediate roof is weak. In this study, the effects of the three factors, the stress angle between the maximum horizontal stress and entry development, the stress ratio of the maximum to the minimum horizontal stresses, and the sequence of entry development, on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method, when the horizontal stress is fixed. The results have confirmed that the stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the angle is about 60°_75°. The stress ratio has little effect on the roof stresses. In addition, the sequence of entry development has also little effect on the roof stress for the specific case analyzed.

Jan 1, 1999

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Amilton Barbosa Botelho Junior

A new step in the Bayer process has been used to recover NaOH and to reduce its content in red mud. After digestion, the residue is separated from the Bayer liquor and goes through press filters, which enables the recovery of NaOH and decreases the moisture content. It is well known that red mud is one of the most important sources of scandium. For this reason, the goal of this work was to characterize a Brazilian red mud (BRM) for scandium recovery. The sample was collected after the press filter system process. Analysis of energy-dispersive X-ray fluorescence (EDXRF), scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS), and X-ray diffraction (XRD) was performed. Microwave digestion using an acid mixture was carried out to determine the concentration of the main elements. Fe2O3 represented 40% of the BRM, and the Sc concentration was 43 mg/kg. The SiO2 content was 24%, which is the highest value found in the literature, whereas the sodium concentration was the lowest. A literature review was carried out to compare results with BRM, as well as the current studies for recovery of scandium by the leaching/ion-exchange process. Scandium recovery using a leaching/ion exchange process may be possible with efficiency higher than 90%. The greatest challenge is the occurrence of silica gel formation during leaching.

Oct 19, 2020

By Peter W. Lipman

In the Rocky Mountain region, variations in Tertiary mineralization correlate with changes in tectonic setting and associated igneous activity that can largely be related to tectonics along the west boundary of the American plate. Successive settings include compressional tectonics and associated continental-arc igneous activity; transitional igneous types associated with intra- and back-arc extension; and basaltic or bimodal basalt-rhyolite assemblages associated with Basin and Range extension in- ward of a growing transform boundary between Pacific and American plates.

Jan 1, 2013

By K. Burke, K. L. Myers, R. Espell

Barrick's Goldstrike AA heap leach pad is an HDPE-lined facility that was used for gold recovery from low-grade ores using conventional cyanide heap-leach technology. The pad was operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA leach pad facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada's closure requirements. The traditional Nevada leach pad closure procedure involves rinsing to reduce the cyanide concentration to an acceptable level followed by reclamation. However, rinsing does not typically reduce certain metals and compounds, and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as in Nevada, the fine-grained layer will rarely reach saturation, and the cover will be able to store water during precipitation events and will allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22-m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the recontoured AA heap leach pad was specifically designed to enhance the re vegetation, reclamation and sediment yield control aspects of the AA heap leach pad closure, while resulting in a natural looking surface that is compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for recontouring and erosion-control design.

Jan 1, 2002

By A. Juganda, Jr. Bogin, S. A. Lolon, J. F. Brune, J. W. Grubb

"A longwall gob is mainly filled with broken rocks from the collapsed roof and becomes a porous medium where explosive methane-air mixtures can accumulate. In bleeder ventilation systems, this mixture can migrate out of the gob into the longwall face and other active areas in the mine during barometric or ventilation-induced pressure changes. When external pressures change, the gob does not perceive this disturbance instantly but with a delay due to air flow resistance in the porous gob material. The delay of gob response to outside pressure changes increases the pressure differential across the gob and may cause an outflow of explosive air mixtures from the gob into the adjacent bleeder entries. With computational fluid dynamics (CFD) modeling, researchers at the Colorado School of Mines have evaluated the impact of gob pressure fluctuations on the outgassing of the explosive gas zones (EGZs), the magnitudes and rates of pressure changes, the volumes as well as the potentials location of outgassing if it occurs. INTRODUCTION The air pressure field in underground mines is controlled by many factors such as operating fan settings, ventilation controls, surface atmospheric conditions, and other local events that can intermittently disturb mine pressure, including blasting, roof falls, or inundations. Mine fan settings are rarely changed. Mine atmospheric pressure fluctuations due to adjustments in ventilation controls occur more often during the mining process. Atmospheric conditions and barometric pressures can generate fluctuations in mine pressure on a large scale. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Investigations conducted in coal mines in the United States, Australia, Poland, and South Africa observed higher methane emissions from the gob during periods of falling atmospheric pressures, which led to mine explosions (McIntosh, 1957; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Belle, 2014; Wasilewski, 2014; Lolon et al., 2015). Falling external pressures are understood to cause potential outflow of explosive mixtures from the gob, while rising pressures may push fresh air into the gob. This phenomenon is widely known as gob breathing. The actual processes that trigger gob breathing are not fully understood, nor are the parameters that contribute to the process. Other major events such as roof falls or fan failures can also change the pressure conditions in the mine. In contrast to atmospheric pressure changes, these events can change mine pressures much more rapidly or immediately. TIME LAG AND GOB BREATHING CONCEPT In a bleeder ventilation system, the pressure in the gob is designed to be lower than that of the headgate entries and the longwall face. Air from the gob and gate entries flows towards the tailgate-bleeder returns. When the external pressures are disturbed, this designed pressure arrangement may change, potentially resulting in increased outflow from or inflow into the gob."

Jan 1, 2017

By W. J. Aitken

The pneumatic conveying of relatively large abrasive materials by dilute-phase conveying techniques has been applied in the underground mining industry for many years especially for backfilling mines and the hoisting of ore, coal, or rock out of the mines. The technique was extensively used in Europe, especially Germany and Britain for backfilling coal mines with rejects from the coal cleaning plants which not only helped to reduce environmental problems on the surface, but offered support to the overlaying strata in the deep underground mines, Similar techniques are being employed in the U.S.A. especially in uranium mines for the disposal of tailings, the main purpose being to extract a larger percentage of the ore from the pillars especially under weak roof conditions. Other than for the backfilling of abandoned mine entries, pneumatic conveying has not been applied in the mining industry in surface applications. In this paper, some consideration is given to three applications for open pit mining which may prove beneficial, namely hoisting coal up the high wall, sealing off auger holes, and stabilizing the high wall when being undercut by a longwall system.

Jan 1, 1981

By Kirsten Corin, Belinda McFadzean, Cyril O’Connor, Jenny Wiese

The Bushveld Complex of South Africa contains almost 90% of the world’s reserves of platinum group minerals (PGMs). In the flotation of PGMs, there are significant challenges arising from the need to treat ever-decreasing grades of the relevant ore deposits. The major challenge in the flotation of these ore bodies is the control and management of the gangue minerals, particularly silicates such as orthopyroxene, plagioclase feldspar, and pyroxene which are often rimmed with talc which makes them naturally floatable. It has been shown that various polysaccharide depressants such as CMC and guar have different properties in terms of depressing the gangue minerals. Since the PGMs are often associated with sulphides, copper sulphate is widely used as an activator in PGM flotation but can inadvertently activate the gangue minerals as well as reduce the recovery of PtTe2 which accounts for up to 40% of the Pt in the Platreef ore body. Depressants also reduce the mass of solids reporting to the froth and can thus destabilise the froth. This effect on the froth can be mitigated by using higher frother dosages or water of higher ionic strength. Reducing chromite recovery is of critical importance since high levels may negatively affect the downstream smelting process. Chromite recoveries can however be reduced through the application of gravity separation or reducing entrainment through reduced water recovery. In summary, due care needs to be taken to carry out site test work to develop an optimum ratio of collector, frother, activator, and depressant to ensure that the highest grades and recoveries of the PGEs are obtained while reducing depressant dosage as much as possible.

By Nikhil Dhawan, Ashwini Kumar, Yogendra Pratap, Himanshu Tanvar

India does not possess any soluble potash reserves and depends completely on imports. In this study, an attempt has been made to recover potash (K) values from the mica sample employing thermal and mechanical routes followed by leaching. Direct leaching of mica in different lixiviants is found to be ineffective with very low K-dissolution (1–5%). Heat treatment with different fluxes, such as NaCl, NaOH, and CaCl2, is carried out and almost 85% K-values are recovered. Mechanical activation of mica and with different calcium additives is carried out to recover potash values. K is recovered in leach solution in the form of soluble salts, such as K2CO3, K2SO4, and KOH, and leach residue consists mainly of calcium-alumino-silicates. Using mechanical activation with flux, it is possible to recover >95% K-values from mica sample. Mechanical activation with calcium-based flux is found sustainable in the recovery of K-values from mica.

By Uday Kumar

This paper presents details of an availability study for a fleet of diesel engine operated load-haul-dump (LHD) machines used in a Swedish mine. For the purpose of this study, the LHD machines have been considered as a system comprised of many subsystems like engine, brake, transmission, etc., in series. As availability is dependent on both the reliability and maintainability characteristics of the system, together with reliability, the concepts of maintainability are also discussed. The need for exploring the data for the presence of any structure, which is very common in repairable system data sets, is emphasized with suitable examples. Simple graphical techniques are used for verifying the independent and identically distributed (IID) assumption for the data set. The error introduced due to the use of the exponential distribution in place of more appropriate distributions in estimation of availability and reliability characteristics is analysed.

Jan 1, 1989

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal mining operations can cause various disturbances to surface structures ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of the travelers and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (e.g., decks, beams, abutments, etc.) are presented. A number of mitigation measures to protect the bridge structures are recommended along with an actual application case.