Search Documents

By A. Acar, E. T. Tuzcu, Y. O. Vural

"In order to sustain the operations in chromite processing plants, due to concentrate selling cost, plants are in need of optimization in terms of capacity and recovery increase. In this study, DAMA Engineering carried out a methodological study for the purpose after a detailed sampling campaign in a plant which is situated in one the main chromite zones in Turkey; 1 The current status of the plant was investigated quantitatively with the bottlenecks, Plant overall efficiency in terms of recovery, Efficiencies of the particular equipment (mill, screen, gravity circuit), 2 A new circuit was proposed with the available equipment, 3 The new circuit that is product of modeling and experimental effort, was evaluated quantitatively as if it is a running plant, After 4-5 months continuous effort, the capacity of the plant was almost doubled (37 tph to 70 tph) and the plant overall recovery was increased from 48% to 63% by grinding adjustments and additional shaking tables theoretically. It was shown that the plant may move into profit with the minimum amount investment using readily available system. INTRODUCTION TO THE CURRENT PLANT The objective of the study is to increase the capacity and recovery of the chromite plant owned by Kurmel Group, Akmetal Inc. The complete study is given elsewhere (DAMA, 2016). The plant is situated in one of the main chromite zones in Turkey; Aladag. The current capacity of the plant is around 35 tph and the overall recovery declared by plant engineer is around 47 %. The chromite plant mainly has 3 units; crushing, grinding and gravitational circuits. The crushing circuit has 3 stages; a jaw crusher, a secondary cone crusher and a tertiary cone crusher operating in closed circuit with a vibrating screen with the aperture size of 15mm. In grinding circuit, a rod mill (2.44 6m x 3.6) and a ball mill (2.13 x 2.3m) are used for primary and secondary grinding, respectively. Derrick screens are used for the size separation. Additionally, for the size classification of the system, hydrosizers are used and each size fraction is sent to the shaking table sets. The middling product of the tables is subjected to re-grinding with a ball mill with the dimensions of 2.1 x 2.9 m. The capacity and the recovery are affected by several bottle necks; hydrosizers’ pure classification, primary/secondary mill power vs capacity problems, re-grinding product’s high slime content and so on. These combined factors made the plant to run in low recovery and capacity. Hence, DAMA was asked to make a study to investigate current status of the plant and propose a new solution to increase capacity and recovery of the plant. The conceptual flowsheet of the circuit is given in Figure 1 below."

Jan 1, 2017

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

Opencast mines are vulnerable to inclement weather conditions as it disrupts the day-to-day activities at these mines. To address the problem, a perceptive driving assistant system (PDAS) has been developed to increase the visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery (HEMM) at opencast mines in harsh weather conditions.

Apr 1, 2023

By H. Vigil Fernandez, G. Peach

The Musaimeer pump station and outfall project located in Doha Qatar, was designed to collect and manage ground and stormwater and then discharge the treated waters offshore. The project constructed a long outfall tunnel using an EPB TBM with segmental lining, each tunnel ring being 1.35 m in length with an internal diameter of 3.7 m.. The diffuser structure was a 6-arm structure, measuring 294m by 40 m connected to a central manifold in turn connected to the TBM constructed tunnel via a riser shaft drilled from an off-shore barge. This technical paper will discuss the planning, methodology and construction practices employed to connect the TBM tunnel to the diffuser structure 10.2 km offshore.

Jun 13, 2023

By E. Allen Wendt

It is both a great pleasure and something of a challenge for me to have this opportunity to address a gathering encompassing such a wealth of expertise in the minerals field, It is particularly challenging because I have been asked to turn your attention from the relatively glamorous subjects of gold and money to the more mundane questions of our International commodity policy and the place of buffer stocks in that policy. However, these questions may be of more immediate importance for our economic interests at home and Abroad. I can testify that the problems affecting international commodity markets and the possibility of international action To resolve those problems are matters of real concern to Washington as well as to your industries,

Jan 1, 1978

By Yves Boissonnas, Marco Bettelini

"INTRODUCTION AND OBJECTIVES The operational safety of long and very long rail tunnels represents a key issue in all development stages, including design, construction, commissioning and operation. The spectrum of potential threats is very broad and challenging. These issues can only be mastered by means of a proper combination of a number of safety measures at various levels. This paper focuses on the specific safety issues and the extremely challenging conditions characterizing very long and deep tunnels. They include a significantly increased risk during operation that the incident train cannot exit the tunnel by its own means, long self-rescue and rescue distances, the presence of a number of trains, possibly mixed traffic as well as significant thermal issues. Amberg Engineering is strongly involved in the design and construction of most long and very long rail tunnels in Europe, including in particular the Gotthard Base Tunnel (GBT), Lyon-Turin Base Tunnel (LTF) and the Brenner Base Tunnel (BBT). The combined experience arising from these tunnels forms an invaluable body of expertise, which is summarized in this paper. The focus is on shared issues with practical relevant examples and project-specific solutions. Special attention will be devoted to the 57 km long Gotthard Base Tunnel, which will be operational by mid-2016 and will be the longest infrastructure tunnel worldwide. VERY LONG TUNNELS IN EUROPE Overview From the point of view of safety, tunnels in excess of about 20 km exhibit a significantly increased risk that incident trains could stop within the tunnel. This is related to the European Technical Specifications for Interoperability (TSI) on rolling stock, to be discussed in the chapter on rescue stations. This paper will specifically focus on the following longest tunnels in construction or operation, listed in Table 1."

Jan 1, 2016

By John H. Raymer

The accuracy of inflow estimates depends largely on how well permeability is characterized. Permeability is best evaluated as a statistical distribution. For the Chattahoochee Tunnel, this distribution was obtained with a large number of packer tests performed in 50 boreholes along the alignment. The distribution of packer-test data may not accurately reflect permeability, however, due to the limits of the test method and the luck of the field investigation. These discrepancies may be overcome by using log-normal plots of the data to develop a permeability model that will be use din lieu of the data to calculate inflow.

Jan 1, 2001

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter and mill speed to be material dependent. A sharp change in the grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (i) the hardness difference between the two clinkers became insignificant, (ii) variation in the grinding rate with particle size became markedly more pronounced, and (iii) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1987

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

One of the most difficult challenges in underground mining is to forecast significant seismic events prior to their occurrence in order to support the safety of miners and to minimize damage to the underground operation. Passive seismic tomography is a tool to image the seismic velocity changes in a rockmass, which can potentially reveal the rockmass behavior before and after a significant seismic event. In this paper, the changes in seismic velocity of the rockmass before and after three major seismic events are investigated to determine whether there are identifiable precursory velocity changes associated with the major seismic events. Conventional mechanics imply that the induced stress at the hypocenter would continue increasing until failure, in the form of an induced seismic event, occurs. With passive seismic tomography we can image changes to the seismic wave velocity distribution within a rockmass and hence infer the changes to the induced stress near the hypocenter. This paper evaluates the hypothesis that induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs. In addition to analyzing p-wave velocity changes near the hypocenter, changes to the p-wave velocity at “zone centers” were also analyzed. These “zone centers” are regions within the rockmass that consistently have a p-wave velocity that is much higher than the average p-wave velocity for the rockmass. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring, however the p-wave velocity did increase in the closest “zone center” for two of the three events.

Oct 12, 2020

By R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al (III) and flotation collectors. It was found that the presence of Al (III) is necessary for good flotation of the organism whether or not Pb(II) is present when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8 and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al (III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminoproprionic acid is used as collector good flotation occurs at about pH 4 without the addition of Al (III).

Jan 1, 1990

By C. E. Jordan

The Tuscaloosa Metallurgy Research Center of the Bureau of Mines, U.S. Department of the Interior, is investigating the recovery of phosphate from beneficiation slime, as part of the Bureau's efforts to conserve mineral resources through increased use of wastes. Phosphate equivalent to about two-fifths of U.S. production is discarded annually in the wastes. Exploratory flotation tests on the plus 5-um fraction of a slime sample showed promise for a classification-flotation technique. Onsite classification tests at six phosphate washing plants were conducted with a two-stage hydro cyclone system designed to recover the plus 5-um material. The cyclone underflows contained 8.3 to 19.1 percent P2O5, and the recovery of the plus 5-um PZOS values ranged from 81 to 95 percent. The percent P2O5 recovery from the total slimes ranged from 38 to 47 percent. Batch-flotation studies are currently being conducted.

Jan 1, 1978

By C. R. Hairfield

With ever rising energy costs, it is increasingly important for mines to operate with energy efficiency. As a large portion of a mine?s energy consumption is often attributed to the operation of mine ventilation fans, maintaining an efficient ventilation system is a critical pro-active way for mining companies to reduce power costs. A common way to measure a mine?s ventilation system efficiency is to calculate the volumetric efficiency, which is simply a calculation of the percentage of total mine air that is usefully employed for production. The purpose of this study is to document a nationwide comparison of the volumetric efficiency of U.S. underground coal mining operations. The results will aim to show just how efficient today?s coal mine ventilation systems are and what factors may be causing their various efficiencies and inefficiencies.

Jan 1, 2009

By Rui Xiang Yang, Cong Li, Jia Zeng, Rong Liang Zhang, Wei Zhang, Chao Fan Tang

This research took the roasted products obtained by leaching copper (Cu) refining slag using waste acids and roasting leaching residues with calcium oxide (CaO) as raw materials and used oxidative leaching to extract Cu from roasted products using waste acids. Influences of the leaching temperature, liquid–solid ratio, and sulfuric acid ( H2SO4) concentration in waste acids on the leaching rate of Cu in the oxidative leaching process of roasted products using waste acids were investigated. The unreacted-core shrinking model of heterogeneous reactions was adopted to reveal the leaching kinetics of Cu in the oxidative leaching process of roasted products using waste acids. Results show that the leaching rate of Cu reaches 91.68% when the leaching temperature, liquid–solid ratio, H2SO4 concentration in waste acids, and injected airflow are 80 ℃, 8:1, 1.5 mol/L, and 200 mL/min, respectively. If the leaching temperature is below 80 ℃, the leaching process of Cu is controlled by the solid-film diffusion, and the apparent activation energy Ea is 11.0835 kJ/mol; at a leaching temperature above 80 ℃, the leaching process of Cu is governed by the interfacial chemical reaction, with an apparent activation energy Ea of 42.3183 kJ/mol. The liquid–solid ratio can positively influence the reaction rate constant. The apparent order of the leaching reaction of Cu is 0.632.

Jan 11, 2023

By Wenkai Wan, Charlie C. Li

Strain burst can occur in underground hard rock excavation when the in-situ stresses are high enough. The prerequisite for rock burst is that the total energy released from the rock mass is higher than the energy needed for rock fracture. The total released energy is contributed by both the burst rock and the surrounding rock. The part of the energy from the burst rock is constant per unit volume of the rock, but the part from the surrounding rock is associated with the burst volume. A greater amount of energy will be released from the surrounding rock in the case of a larger volume of burst rock. The postulation for the energy conversion in strain burst is verified through a FLAC3D model in the paper. It is assumed that the strain burst occurs in a circular tunnel that is located in the hydrostatically loaded rock mass in the model. Six pairs of notches with different depths are created in the opposite walls of the tunnel to simulate the bursts. The energies released from the notch rocks and from the surrounding rock are calculated during the burst. The simulation results show that the percentage of the energy released from the surrounding rock in the total released energy increases with the notch depth. The numerical modelling confirms the postulation that the surrounding rock contributes more energy than the burst rock itself in large-scale strain bursts

Apr 26, 2022

By James W. Derrick

General widespread interest in fine coal cleaning circuits did not occur in the United States until the mid 1960's. Up until this period the relatively low price for which bituminous coal was sold did not justify for many operators the capital and maintenance costs associated with the beneficiation and drying of fine coal. However, with current growing interest in this area, the introduction of new types of process equipment along with modifications to existing components is occuring to maximize the recovery of coal fines. In 1973 Derrick Manufacturing Corporation introduced high frequency screening machinery into the coal industry. The first design consisted of a 4 ft. wide 18 ft. long single deck screen frame with three 100 mesh woven wire screen surfaces divided by repulping troughs for the addition of wash water. In addition, a special slotted rubber dewatering deck was installed on the discharge end of the unit to assure adequate dewatering of the screen oversize. This panel had nominal 25 mesh X 3.0" slotted openings. The machine was also equipped with a special high speed-low amplitude (3600 RPM .032" % AMP.) integral vibrator.

Jan 1, 1983

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The reliable quality assessment of grouting operations is one of the key issues in establishing impermeable grout curtains around shafts, drifts and tunnels. Reliable opera¬tional information on the decrease in the permeability of rock during the grouting process facilitates the assessment of the effectiveness of the completed curtain and assures production quality. Quality control and assurance also fa¬cilitates the early detection and elimination of possible de¬fects in the grout curtain. Thorough control of the grouting process provides the capability to evaluate decreases in the permeability of water-producing fracture zones prior to the beginning or the continuation of excavation of the shaft, tunnel or drift. In order to achieve this objective, post¬grouting hydrodynamic investigations are conducted prior to the initiation or re-initiation of work on the underground workings to measure the decrease in the permeability coef¬ficient of aquifers during grouting operations. 8.1 QUALITY ASSURANCE AND CONTROL OF THE ISOLATION OF ROCK BY GROUTING THROUGH HOLES DRILLED FROM THE SURFACE Quality assurance and control are based on measuring the decrease in the permeability coefficient of water-pro¬ducing horizons as a result of injecting grout into the drill¬holes. For this purpose, the value of the acceptable residual permeability coefficient is calculated beforehand based on the acceptable value of ground water inflow into the shaft, drift or tunnel as specified by the "construction norm and integrated practice (SNIP)" (Anon., 1976). Having ob¬tained the values of aquifer thickness, permeability, and head distribution for each aquifer from flowmetric data (dis¬cussed in Chapter 3), the average value of the permeability coefficient of all aquifers intersected by the shaft is calcu¬lated as [ ] where Ki is the permeability coefficient of the "ith" aqui¬fer; Pi is the pressure of the "ith" aquifer; and M; is the thickness of the "ith" aquifer. The total expected inflow of ground water into the shaft is [ ] where RK is the radius of the contour of influence; RCFB is the radius of the shaft; and p is the coefficient of dynamic viscosity of the ground water. The necessary reduction of the coefficient of permeabil¬ity of the aquifer [ ] where Q is the expected inflow of ground water into the shaft from eq. 8.2; Q.-fin is the acceptable inflow of ground water; and a is the safety factor. By knowing the average permeability value of the rock and the permeability reduction coefficient, it is possible to determine the value of the acceptable residual permeability coefficient for all the aquifers [ ] The values of the permeability coefficient, pressure, and thickness for each aquifer are determined from the data gathered during the hydrodynamic investigations conducted in grout holes prior to beginning the grouting operations as discussed in Chapter 3. After injecting the grout into the first of the holes, the injection into each of the following grout holes is preceded by repeated hydrodynamic investi¬gations. Using the data obtained for each water-producing zone, a graph is constructed where the numbers representing the grout holes in their order of grouting are placed on the abscissa, and the values of the aquifer permeability coeffi¬cient are placed on the ordinate (Fig. 103). This curve char¬acterizes the change in permeability of the given hydro¬stratigraphic unit as grouting operations are completed, one hole at a time. The results of grouting operations are considered to be positive when each sequential observation records a steady decrease in the permeability of the aquifer. The permeabil¬ity measured prior to the injection of the grout into the last hole must be lower than or equal to the acceptable perme¬ability as determined by the application of eqs. 8.1 through 8.4. Table 8.1 presents illustrative data on the hydrogeo¬logic properties of aquifers at a mine shaft prior to the initiation of grouting operations. Data also are presented on the reduction in the permeability coefficient during the in¬jection of the grout. The shaft in question intersects eleven aquifers. Based on data concerning aquifer pressure, thick¬ness, permeability, and the expected inflow rate of water for each of the strata, the average permeability coefficient is calculated according to eq. 8.1 as K = 0.2 x 10-12 m2. The

Jan 1, 1993

By J. S. Carman

As with the slogans of Madison Avenue, catch words or phrases frequently become topical. Much is heard these days of the confrontation between governments of developing countries and international mining capital. In actual fact, sadly there are too few cases of anything as positive as confrontation because such an action at least signifies a dialogue which may begin badly but end up fruitfully. Instead we have in general a climate of indifference and fear with the mining companies of note marking off most of the developing world as being unsafe for investment. There is an unreal air to this damaging impasse. The common sense and objectivity which are prerequisites of positive action are lost in a swirling cloud of mythology, embraced largely by governments. Let us examine some of the dangerous misconceptions.

Jan 1, 1977

By LaPoint D. J.

Copper deposits in sandstones are excellent targets for open pit mines using SX-EW extraction and processing methods. The mineralogy consists of chalcocite as the primary sulfide and copper carbonates and sulfates in the zone of oxidation. Two general deposit types are recognized: early diagenetic copper deposits that are associated with the reddening of the surrounding sediments, and epigenetic deposits that are associated with the migration of copper-rich basinal fluids along faults into permeable reservoir beds with a source of reductant. Epigenetic copper deposits are more likely to contain enough tonnage to be economic.

Jan 1, 1996

By J. Espí

The mineral price assigned in mining project design is critical to determining the economic feasibility of a project. Nevertheless, although it is not difficult to find literature about market metal prices, it is much more complicated to achieve a specific methodology for calculating the value or which justifications are appropriate to include. This study presents an analysis of various methods for selecting metal prices and investigates the mechanisms and motives underlying price selections. The results describe various attitudes adopted by the designers of mining investment projects, and how the price can be determined not just by means of forecasting but also by consideration of other relevant parameters.

Aug 1, 2013

By E. A. Domínguez

La Espingarda kaolin deposit was formed by ?in situ? alteration of volcaniclastic rhyolitic rocks belonging to Jurassic Marifil Formation. Three volcanic lithofacies were identified: porphyric biotitic ignimbrites (PBI), a coarse lithic ignimbrite (ILG), a fluidal intrusive rhyolite (RFI), all kaolinized in different degrees. The alteration covers an ellipsoidal area of ~20,000 m2, with its alteration decreasing downwards and disappearing at 8-12 m from the surface. The length to thickness ratio of alteration is 60:1. An erratic silicification was found as small zones (<3 m2) of quartz stockwork. The mineralogy is kaolinite + quartz + feldspars + Fe-oxyhydroxides ± halloysite ± illite and interstratified I/S, although the relative proportions change in each rock type. Due to coarse grain size and high quartz content, natural kaolin is unsuitable for slip cast ceramics, unless beneficiated. Washed ILG kaolin has the best rheological properties and behavior in casting and drying for its mineralogy, particle size distribution, thin texture and surface activity, as well as a certain fusibility and firing kinetics. PBI and RFI kaolins, due to finer texture, smaller grain size, lower surface activity, and higher halloysite amount, have worse slip viscosity and thixotropy that are due also to soluble salts. For the same reason, they have good casting and drying properties, but their purity brings about higher softening temperatures and water absorption. Several parameters are used to discriminate between hypogene or supergene kaolinite genesis. The hydrothermal genesis is mainly sustained by fluid inclusion temperature (150-180ºC) in quartz veinlets, while weathering is supported by deposit morphology, simple mineralogy, kaolinite stable isotopes (d18O ? 18, 13; dD ? ?59; ?85) and paleoclimatic record. It is concluded that a weathering process formed the main alteration with some participation of steam-heated meteoric waters. Neither the contents of Au, Ag, As, Sb, Hg, nor drill data support the existence of any epithermal gold mineralization at the kaolinite bottom.

Jan 1, 2010

By K. Perry, B. Lusk, Q. Huang, R. Honaker

"Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. The application is conducted either dry or wet. Both methods have advantages and disadvantages however the formation of caked rock dust particles is cited as a significant concern for wet applications. A study was conducted to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid (OA) and sodium oleate (NaOL). At a NaOL dosage of 2 lbs/ton, a contact angle of 112o was measured indicating strong surface hydrophobicity and ability to repel water. FTIR studies indicated a chemisorption mechanism which is necessary for long term stability of the surface modification. The dispersion rate of the modified rock dust samples was elevated by the application of both OA and NaOL thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed a 79% reduction in the dust explosion potential relative to untreated rock test applied by the wet technique. INTRODUCTION Mine explosions have been a long-time threat to underground coal miners attracting significant attention to the accumulations of combustible dusts and gasses. In the presence of sufficient oxygen and heat, the accumulations of combustible dust and gass can lead to large-scale underground coal mine explosions [Harris et al., 2010]. To alleviate the problem, rock dust such as limestone can serve both as a thermal inhibitor and a heat sink to inert the coal dust explosibility thereby prohibiting the occurrence of dust explosions [Richmond et al., 1975; Amyotte et al., 1995; Dastidar et al., 1997; Man et al., 2009]. The dispersibility of the rock dust is an important characteristic that determines the degree of explosion prevention [Greenwald et al., 1938; Mozumdar et al., 1974; Amyotte et al., 1995]. Unfortunately, the environmental conditions of an underground mine has the potential to cause caking of the rock dust which reduces the dispersive characteristics needed. The dispersive property of rock dust can be enhanced by modification of the particle surface properties by the application of chemical additives [Greenwald et al., 1938; Mozumdar et al., 1974; Spence, 2004; Vogt, 2011; Doidge et al. 2014]. The major mechanism for rock dust caking is the adsorption of water which forms liquid bridges at the particle-particle contact points where saturated solutions of soluble powder ingredients are present. Changes in temperature or relative humidity result in solvent (water) evaporation and the formation of dry bridges [Rumpf, 1958; Specht, 2006]. One method to prevent caking is creating hydrophobic rock dust to repel water from the solid surface thereby preventing the formation of liquid and solid bridges."

Jan 1, 2015