Search Documents

By T. P. Meloy

The packed column flotation cell is an awesome separation device. Virtually unknown and untested, the packed column flotation cell is one of the ten most important developments in mineral processing of the 21st century. Though experimental and industrial data is limited, it is clear that the packed column flotation cell is two to three orders of magnitude better than the conventional flotation cell and one to one and a half orders of magnitude better than the open column flotation cell. With the modern packing taking up less than one percent of the packed column, column blocking does not occur. For a packed column operating 24 hours a day, 365 days a year, the estimated mean time between failures (MTBF) is one hundred thousand hours or roughly twelve years. With no moving parts, lower maintenance costs, lower power consumption and inherent operating stability, the packed column is a powerful separating machine. Because there is little meaningful data for comparing the packed column to the conventional flotation cell and the open column flotation cell, much of the material presented in this paper are guesstimates. They are disinterested guesstimate made by the authors after extensive theoretical work and reviewing the known facts. In the authors' opinion, no available data contradicts the guesstimate. The authors expect that there may be errors as large as three hundred percent. Even three hundred percent errors will not change the conclusions of this paper. The packed column flotation cell is a formidable separating device. To understand the problems of comparing the three types of flotation cells, consider the fact that the three cells may have different modes of separation. One of the authors, Meloy, believes that in the conventional cell, the primary particle separation takes place in the liquor with secondary separation taking place in the froth, while for open column flotation, all the separation takes place in the froth. However, he believes that in the packed column a large part of the separation may take place on the walls of the packing. If this is true, not only is the method of modeling each type of cell different, but the method of particle selection in the cell is different. This means that one type of cell may be better at differentiating between two different types of particles. There is a growing body of literature on open and packed column flotation. Suggested reading: (Clarke et al; Hucko et al; Li; Smith & Warren; and Yang).

Jan 1, 1994

By J. Luo

A major design problem for upper seam longwall gate roads that are to be constructed in a multi-seam environment is to predict the effects of stress field changes created by interaction. To quantify these effects, case study data were analyzed to develop empirical stress transfer relationships between seams for both longwall and room and pillar mining. Data analysis showed vertical movement and roof characterization in the upper seam to be controlling factors in damage prediction and, therefore, gate road planning and design. CMRR (Coal Mine Roof Rating) was correlated with the multi-seam roof characterization systems previously used. A WINDOWS-based software package named UGLY (Upperseam Gateroad Longwall Stability) was developed. Results from selected case studies were correlated with upper seam stress predictions.

Jan 1, 1997

By K. Lapakko

One responsibility of the Minnesota Department of Natural Resources is to encourage the development of mineral resources within the state. A second responsibility is to ensure that mineral development does not adversely impact other natural resources, including the water resources of the state. One approach the Division of Minerals has taken to fulfill these responsibilities is to conduct cooperative research with the mining industry. To encourage mineral development the Division has cooperated with industry on projects related to exploration, mining, and mineral processing. To examine environmental issues the Division has worked in concert with iron ore, base metal, and precious metal exploration and mining companies, as well as the Western Governors' Association, US Bureau of Mines, US Bureau of Land Management, and the US EPA for the past 20 years. These projects were conducted to evaluate methods of predicting, preventing, controlling, and treating problematic mine waste drainages, as well as mine waste revegetation. This paper I) briefly summarizes cooperative projects conducted, 2) enumerates elements which have contributed to the success of cooperative projects, and 3) describes changes implemented for future projects at the Division's new field and laboratory research facilities, as well as at existing mine and plant sites.

Jan 1, 1998

By Heinz Distelmeier

The New Austrian Tunneling Method was, as is well known, developed from conventional rock tunnelling. In Germany about 10 years ago the NATM began to be applied to partially stable soils by incorporated excavation and support methods to allow its use with these soils. The advantages of this tunnelling technique - adaptability, ecomomy, and quality have resulted in its widespread usage. Today, about 85 % of all mined tunnels in Germany are produced with this technology. This rapid development has resulted in about 40 companies operating within a geographical area about the same size as the state of Illinois that are capable of utilizing the NATM. In most cases German contract/award procedures allow the contractor to develop alternate design and plans. As a result of this flexibility and intense competition, safety factors have been gradually reduced to the lower limit of what could be regarded as demonstrably safe, and the utilization of the NATM has expanded to include higher risk conditions, namely * excavating larger cross sections. * working with less overburden. * work undertaken under less stable soil conditions.

Jan 1, 1983

By R. M. Rowe, T. E. Irwin

A flowsheet was developed for upgrading Climax tin concentrate to about 45 percent Sn. Bench-scale test work conducted at AMAX Extractive Research and Development, Inc., was used to design a multiple-stage tin- processing flowsheet which included screening, high-intensity magnetic separation, and high- tension (electric- static) separation. Formal engineering and plant installation was accomplished in-house by Climax mill personnel. The successful start-up operation of the facility was the joint effort of the AMAX R&D and Climax-mill staffs.

Jan 1, 1986

By Donald E. Ralston, A. T. Yu, Richard P. Killmeyer, Peter Phillips, R. W. Vander Laan, John N. Murphy, John R. Messineo, John Peters

Overview Coal production in the first half of 1982 remained near the high levels begun in mid-1981. Production then fell sharply during the latter part of the year due to recession-weakened demand. Even so, 1982 coal production was estimated at 756 Mt (833.4 million st), a record high that exceeded 1980's previous production record of 752.7 Mt (829.7 million st). Though 1982 coal production was substantially below industry expectations, the attained production represented a modest achievement in view of the recession's severity. In 1982, the gross national product declined 1.8%, its worst performance in 36 years. The recession, along with mild weather, improved energy efficiency, and conservation efforts caused the nation's energy use to drop 4.1%. With the iron and steel, construction, and auto industries experiencing production declines, industrial energy use fell 10.8%. The extent to which the nation's economic slump affected coal markets in 1982 varied: • total domestic coal use declined 3.4%; • exports remained strong for most of the year; • electric utility coal use declined for the first time in 25 years; • coal use at coke plants declined by one-third; and • coal use in other industrial sectors stayed surprisingly near the 1981 level. Coal Use Domestic coal use totaled 641.8 Mt (707.5 million st) in 1982,22 .9 Mt (25.2 million st) below the 1981 level. Nearly all the decline occurred at coke plants where use dropped to 37.1 Mt (40.9 million st) in 1982 from 55.3 Mt (61 million st) in 1981. The decline in all other industrial and electric utility coal markets was only 5.3 Mt (5.8 million st). Residential and commercial coal use increased 635 kt (700,000 st) to 7.3 Mt (8.1 million st) from 6.7 Mt (7.4 million st). Power generation decreased 2.3% in 1982, the first year since 1945 that output failed to increase. The decline was due to a drop in industrial demand. Electricity sales to residential, commercial, and other nonindustrial users increased slightly. But coal's competitive position stayed strong. Power generation from oil and natural gas fell 28.9% and 11.7%, respectively. Power generation from coal declined only 0.9%. Among the primary energy sources, coal fueled 53.2% of US electric power generated in 1982, compared with 52.4% in 1981. In 1982, US steel production declined to 66.1 Mt (72.9 million st), the lowest level in 50 years and down from 109.6 Mt (120.8 million st) in 1981. The reduced steel demand forced 13 coke plants to shut down. Coal Exports Coal exports in 1982 totaled 96.4 Mt (106.3 million st), 5.7 Mt (6.3 million st) less than in 1981. Despite the worldwide recession and above normal coal stockpiles in many countries, exports were higher than many expected. This showed the relatively strong US position in international coal trade. The US continued to export near-record coal tonnages despite increasingly competitive influences. These included an improvement in Australia's labor difficulties, the return of Polish coal to Western European markets, and lower oil prices. In 1982, US port facilities were improved and expanded, and more efficient methods for scheduling foreign vessels were implemented. As a result, high volume coal shipments to US ports were routinely loaded and dispatched unhampered by bottlenecks that plagued East Coast ports in 1981. Appalachian coalfield production declined 1.4% from 1981 output and 3.9% from 1980 output. The interior region of the US showed an increase of 7.8% in production. This was primarily because of a

Jan 5, 1983

By Sakshi Hazuria Anderson, Angela Binder, Oscar Jaime Restrepo Baena, Simit Raval, Sandra Nowosad

As the mining industry faces times of change, new challenges arise to ensure raw material supply for future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net-zero requirements for improving long-term operation performance, technological advancements such as automation and digitalization, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields, leaving mining engineering as one of the less preferred career options for students. Nonetheless, it is essential to continue addressing and supplying the skill sets that are suited to the contemporary and future mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, upskilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more. In countries like Australia, where mining plays a crucial role in the economy, the need for curriculum updates is more pressing than ever. As the mining industry evolves with new technologies and sustainable practices, there is a growing demand for a workforce skilled in these modern approaches. Recognizing this necessity, universities such as the University of New South Wales and Curtin University have taken significant steps to revamp their educational programs. By updating their academic offerings, both universities aim to equip graduates with the necessary skills to drive innovation and sustainability in mining, supporting Australia’s development as a leader in this critical sector. Moreover, the selection of topics that drive curricula update and the focus of the research institutions in mining engineering must extend beyond mere technological and technical aspects to include social and ethical dimensions. In this context, the Universidad Nacional de Colombia, in association with the Colorado School of Mines, has introduced the topic of humanitarian engineering (HE) in 2020. HE is a sociotechnical approach that focuses on developing engineering solutions that promote the sustainable development of communities addressing their basic needs and aiming to improve their quality of life (Menéndez-Aguado et al., 2023; Smith et al., 2023). By focusing on sustainable development, community engagement and equitable resource distribution, HE helps the industry build positive relationships with stakeholders, reduce conflicts and foster social license to operate. As the mining industry seeks sustainable and socially responsible practices, future engineers require training in this area to understand the broader impacts of their work, fostering a mindset that prioritizes community well-being and environmental stewardship alongside technical proficiency. However, developing skills toward humanitarian engineering and sustainable mining among new generations of mining professionals remains a complex task. Integrating the necessary content to prepare future engineers for the multifaceted demands of the industry into a single study program poses significant challenges. To address these complexities, modern educational approaches such as the ones integrated in the mining engineering programs at Clausthal University of Technology can be leveraged to enhance both teaching and learning experiences (Binder, 2024b; Bothe-Fiekert et al., 2023; Nowosad et al., 2024). Innovative teaching methods, such as blended-learning, project-based learning, case studies, scenario simulations and interdisciplinary collaborations, can help bridge gaps by fostering critical thinking, creativity and empathy among students. By embracing modern pedagogical strategies, institutions can better equip future engineers to navigate the evolving landscape of the mining industry responsibly and effectively.

Dec 1, 2025

By R. Q. Honaker

Until recently, the application of the Jameson Cell technology in North America has been restricted to minerals processing. Recently, laboratory, pilot-plant and full-scale testing has been conducted to assess the Jameson Cell's ability to effectively treat fine coal. Based on the data, carrying-capacity relationships have been developed. In addition to its operational simplicity, the Jameson Cell has the ability to provide a separation efficiency near the theoretical separation performance on the basis of ash rejection while achieving a relatively high throughput capacity Tie results obtained from the various fine coal cleaning applications in North America is presented in this publication.

Jan 1, 1999

By William H. Pomroy, Annie M. Carigiet

This U.S. Bureau of Mines report is an analysis of underground coal mine fire incidents occurring in the United States during the 15 years from 1978 through 1992. The fire data used in this analysis were obtained from Federal Mine Safety and Health Administration (MSHA) mine fire investigation reports. Fires were analyzed by year, state, coal bed thickness, mining method, evacuation measures taken, ignition source, burning substance, location, equipment involved, detection method, time of day, number of injuries and fatalities, and method of extinguishment. In all, 164 fires are reported, or an average of 10.8fires per year. The most common ignition source was electricity, the most common burning substance was coal, the most frequent fire location was the belt entry, belt conveyors were the most common equipment involved in fires, and water was the most common extinguishing agent.

Jan 1, 1995

By N. K. Davé

Water quality impacts of shallow water submersion of partially weathered and oxidized waste rock containing reactive sulphide minerals were investigated in laboratory column lysimeter studies. The waste rock investigated was highly reactive, contained oxidation reaction products from previous exposure and weathering, and had a low sulphur content of approximately 2 % S, mostly as pyrite. The submerged waste rock, though previously weathered, had high oxygen consumption, resulting in rapid depletion of dissolved oxygen in its pore water, within a shallow depth of ~2?5 cm from the surface. The surface and pore water qualities of the submerged waste rock were significantly impacted by the dissolution and release of previous-oxidation-reaction products, which contributed to their rapid acidification and having increased concentrations of dissolved SO4, Fe total and other metals: Al, Mn, Ca, Cu, Ni, Zn and Pb. Despite the high porosity and permeability of the waste rock, the diffusion controlled mass transfer from the submerged waste rock to the overlying water cover was relatively low for most ionic species. Additional surface oxidation of the sub-merged, partially weathered waste rock was on-going, but its impact on the overall surface water quality was low and masked by the dissolution and release of previous oxidation reaction products to both surface and pore water regimes.

Jan 1, 2006

By R. J. Sheets

In 2009 the Gold Quarry open pit mine, located 11 km northwest of Carlin, Nevada, USA, experienced multiple large-scale slope instabilities of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope instabilities occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower clay-rich sub-units of the Carlin Formation (Fm.). This deformation created preferential flow paths that allowed groundwater from the upper sandy sub-units to infiltrate low permeability clay-rich sub-units, thereby enhancing deformation of the slope toe which in turn destabilized the upper portion of the highwall. The outcome was a 160 m high slope instability that had a lateral run-out of 850 m. The effort to return the pit to ore production required both the geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This approach required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with blast induced, localized slope failures. Back-analyses applying numerical modeling indicated that the failure surface did not coincide with initial interpretations based on field observations; drilling results eventually confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the lower clay-rich sub-units. The outcome is a stable highwall within the Carlin Fm. following nearly ten years of repeated slope instability, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new open pit development.

Feb 23, 2014

By Kendall Y. Onstott

The paper presents the results of a plant test using WEMCO 1 + 1 enclosed flotation machines for inert gas (nitrogen) flotation of by-product molybdenite from copper sulfide concentrate. Copper depressant consumption in the rougher flotation stage was reduced by 68% as reagent consuming oxygen was removed from the flotation air. Unlike other nitrogen flotation systems used in the industry, nitrogen is recovered above the flotation cells and from froth in tails and concentrate streams and recycled, resulting in minimal nitrogen makeup requirement.

Jan 1, 1984

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982

By R. M. White

Abstract. Gulf Coast Salt Domes are being considered for radioactive waste disposal and this paper describes the geophysical techniques currently being used and those being considered for later phases of the program. Detailed gravity work utilizing a modification of the Talwani-Ewing modeling technique, shallow high resolution reflection seismic surveys using the mini-sosie concept, surface electrical resistivity and down-hole geophysical logging to add a third dimension to all of the surface techniques and to allow inverse modeling of the surface data sets are being utilized. The logic of the combined geophysical surveys will be discussed as well as their relative economics and their relationship to the overall exploration effort.

Jan 1, 1980

By V. Price

Abstract: Action of certain strains of bacteria has been implicated as a significant factor in the oxidation of ore deposits. Other bacteria are thought to be significant in the formation of syngenetic sedimentary ores and in supergene enrichment processes. A normal soil/ground-water regime provides all of the necessary pH and Eh conditions for several groups of bacteria which influence the sulfur cycle in nature. Limiting concentrations of nutrients such as sulfate ions can determine whether a particular microbial species is active at a given place. In the present study, ground water was analyzed from a mineralized area and from a presumed barren area. Trace metal content of the ground water gave no well defined clue as to the presence of a sulfide ore deposit. Sulfide producing bacteria (presumably sulfate users) were found in water from about 50% of wells sampled in the mineralized area and in about 30% of samples from the barren area. These bacteria are readily detected and may provide a useful tool for regional geochemical recon-naissance. Bacterially produced sulfide ions can remove metals such as copper and zinc from solution thus complicating the interpretation of hydrogeochemical prospecting.

Jan 1, 1972

By Jayson Ripke, Peter Amelunxen, Brandon Akerstrom, Fernanda Solís

It is commonly known in the industry that one of the key challenges for a greenfield project, such as Capstone Copper’s Santo Domingo project, is the obtention of samples for metallurgical testing and subsequent plant design. To face this challenge, the Santo Domingo project completed 169,692 meters of drilling. The material collected has been used for a variety of analysis including the economic recovery of iron, which contributes significant economic value to the Santo Domingo business case. Composite and variability samples, covering the main geological units considered in the life of mine (LOM) plan, were selected for bench and pilot scale testwork. Davis Tube Tests, small scale Low Intensity Magnetic Separation (LIMS) tests and a pilot utilizing a 48 in (1.2 m), diameter magnetic separation drum were completed. The testwork demonstrated that the Santo Domingo ore could achieve iron concentrate grades of 65% Fe - suitable for blast furnace, and 67% Fe - suitable for Direct Reduction, primarily by concentration of magnetite. The outcomes of this work have informed the iron concentrator plant design and scale up.

Feb 1, 2025

By J. H. McNamara

A process has been developed for the successful hydrometallurgical extraction of copper from sulfide ores. The extracted copper in the form of a salt is converted by reduction to copper metal. Purification of the metal is described which includes a description of the casting of ETP quality copper wire bars.

Jan 1, 1978

By Donald E. Zipperian

It has been recognized that froth flotation of mineral particles utilizing rising flow of micro size air bubbles, counter-current to quiescent falling flow of particles in a column type cell, provides a unique mechanical atmosphere conducive to extension of froth flotation process to much coarser and finer particles sizes than possible with mechanically agitated and aerated cells. 1,2,3,4. This paper describes metallurgical results obtained at several plant installations of large capacity commercial size Deister FLOTAIRE® Column Flotation Cells. These cells utilize air aspiration into surface tension lowered water to generate micro size bubbles. Operating costs, power, wear, and scaling characteristics of rougher, cleaner, and scavenger units are compared with mechanical units. Problems encountered and scale up criteria developed when increasing from 0.20m(8inch) diameter pilot cells to 2.42m(96inch) commercial cells are discussed.

Jan 1, 1985

A significant technological development is discussed for the processing of certain problem power plant flyashes which contain a high water soluble mineral content and which are known to yield inferior flyash based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash based structures. Favorable changes are evident in (1) sodium silicate consumption, where often approximately one-half of the amount used for making brick from normal flyash is required; (2) processing costs; and (3) strength and appearance of the resulting freshly formed green and fired structural products. In some high cost instances-(above the cost of 30 dollars or less per thousand brick estimated for normal flyashes) hydrochloric acid additions can replace or reduce other costly additives required with problem flyashes to result in a savings of as much as nine dollars per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble, sulfur as a result of the eventual application of certain experimental air pollution control processes.

Jan 1, 1968

By L. J. Tucker

The magnetite orebody at Pea Ridge strikes NE-SH and dips at about 800 to the SE. The ore is high grade magnetite with a strike length of over 600-m and a maximum width of over 180-m on some of the levels. The shape and the mineral content of the iron orebody have been fairly consistent so far. The iron ore and surrounding basement rocks are Precambrian in age. These rocks are usually very competent, about 400-m of sediments lie over the ore.

Jan 1, 1991