Search Documents

By Thomas J. Kingston

A general overview of the taconite crushing process at Minntac is presented The process is controlled from a central control where the control room operator uses closed circuit TV, computer process control and alarms, graphic panels, and radio communication to roving attendants to run the Plant. This paper points out the operating controls and parameters as the plant operator sees and uses them.

Jan 1, 1980

By G. K. Hoffman

Humate, defined as weathered coal or mud-stone rich in humic acid (HA) and fulvic acid (FA) have been mined, primarily as soil amendments or drilling mud additives, in New Mexico for 15-20 years. The New Mexico humate resource is estimated to be 11 Gt, including weathered coal and organic mudstone. The HA and FA content determines the end-use, therefore a simple and consistent method of measuring organic-acid content was developed. The New Mexico Bureau of Mines and Mineral Resources method is based on repeated alkali leaching and acid precipitation. Precipitates of humate are ashed, with mass balance of solids maintained, to correct for material added during alkali-acid treatment. Analyses of upper coal member, Cleary Coal Member (Menefee Formation) and Fruitland Formation samples from the southeast San Juan Basin show ashing to be important in accurate analysis of FA content. Ash in the total FA fraction averages 70% compared to 2% in HA. The FA in weathered coal and organic mudstone are similar, although HA is significantly higher in the former. As weathering progresses, the FA content of weathered coal increases faster than in organic mudstone because of the greater total organic material in coal.

Jan 1, 1994

By D. Denton, C. Peppin, D. Tesarik, D. Bayer, J. B. Seymour

Hecla Mining Company and NIOSH cooperated in a study to document the safety of rock support supplied by reinforced cemented paste backfill at the Lucky Friday Mine. Data are presented on backfill modulus values from laboratory tests and compared with modulus values from in-mine wall closure on the backfill. It is theorized that a compressive zone is created in the backfill between the upper and lower bearing plates on the reinforcing bolts, and that the backfill remains stable as long as the compressive zones from adjacent bolts overlap.

Jan 1, 2001

By Roger Bell

Most modern mines can profit from improvements in information handling. Recording systems in many cases were designed to satisfy certain necessary legal requirements, but not specifically to provide management information. As a consequence, the top managements of these properties work with cost data and production information that is dated, lacking in detail and clouded with supposition. It is the intent of this paper to describe an information system for a mine-plant complex in terms of the type of data, application areas and the existing equipment technology that may be applied to improve this situation. The economics of information processing and data handling will not be discussed in detail. This paper is based on the premise that information is something of value and that information processing like a manufacturing operation works for and is subject to management control. Information, the product, must be of quality, and the cost must be favorable in terms of its use.

Jan 1, 1965

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

Dynamic permeability is a significant hydrologic condition associated with in-situ leaching at the Cyprus Casa Grande operations. Several factors contribute to changes in the permeability conditions. They are: 1) hydraulically induced fracture development, 2) geochemical changes during leaching in the rock matrix, and 3) changes in the relative degree of saturation of the deposit. Dynamic permeability conditions were evaluated using available pressure and flow rates from the 58 injection and recovery wells obtained over one year period. A finite element, 2-D hydrologic model called INVERT which is designed to estimate aquifer parameters under transient and steady state flow conditions was used for the investigation. The permeability conditions during 7 different steady state intervals throughout the one year time frame were determined. The results confirm that big changes in permeability occur as a function of time as well as a function of injection pressure condition.

Jan 1, 1991

By Donald P. Richards

Is a shaft the same as a tunnel and can it be approached in the same manner for design and construction? The most obvious difference between a shaft and a tunnel is that of orientation; whereas a tunnel is commonly near horizontal or slightly dipping, a shaft is commonly vertical or steeply inclined. As a result, design and construction methods employed for tunneling, in general, cannot be directly applied to shafts, although some of the basic concepts of behavior are quite similar. Many of the shafts that have been sunk in various parts of the world are owned by private mining companies. Each company has generally accumulated years of experience in shaft sinking and mining techniques pertinent to its particular geographic location. When a new shaft is to be sunk or an existing shaft deepened, the tendency often seems to be to continue to use the methods that have been used successfully in the past.

Jan 1, 1979

By Daniel de la Rosa, Juan Manuel Mayoral, Damián Vital

"This paper presents a numerical study regarding the loads, and the corresponding damage, taken by the primary and secondary lining of a tunnel built in cemented fine-grained stiff soils. This study aims at establishing more rational design criteria that take into account explicity the lining performance. A 3.5 km long tunnel to be built in a densely populated northwest area of Mexico City, was considered as case study. Series of three-dimensional finite difference models, developed with FLAC3D, were used to simulate the tunnel construction, and to compute the ground settlements, internal forces, bending moments, and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams were used to study the lining performance. Several advancement lengths, and tunnel covers were considered to establish their impact on the loads transferred to the tunnel lining. A practice-oriented damage criterion for tunnels was proposed based on the interaction diagram analysis. INTRODUCTION Lining performance during conventional tunnelling, CT, as defined by the International Tunnel Association, ITA (ITA 2009) is strongly affected by the construction procedure. Special attention must be taken in cemented fine-grained materials, such as those found in the northeast portion of Mexico City, due to the potential of fragile failure (i.e. the soil fails suddenly without important deformation) that these soils may exhibit. During CT, it is assumed that the ground strength contributes to the stability of the excavation, as long as the lining is built correctly. It is common practice to consider two structures, which together form the tunnel support: 1) A primary lining, which is a flexible support, which allows excavation walls to deform to mobilize part of its shear strength, and thus contributes to the tunnel self-stability, and 2) A secondary lining. Commonly, the primary lining consists of several layers of shotcrete. In this case the installation method guarantees perfect contact between the lining and the excavation perimeter. The secondary lining, if required, is used to withstand the load conditions in the long term and also has an esthetic function. This paper presents a numerical study aimed at establishing a performance damage criterion for the primary and secondary lining design in cemented fine-grained stiff soils. Due to the lack of data, the strength and deformation parameters were established through empirically-derived relationships. Three-dimensional finite difference models were developed to simulate the tunnel construction, and compute ground settlements, internal forces, bending moments and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams, along with a damage criterion were used to study the lining performance. From the results gathered insight was gained regarding tunnel lining performance during CT."

Jan 1, 2016

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By S. Ersayin, I. Iwasaki

Application of a magnetic field was shown to be effective in controlling iron losses in pilot-scale cationic silica flotation in the processing of magnetic taconite concentrates. The design of a magnetic field distribution device and batch flotation test results using a 1.42m3 (50 cu. ft.) WEMCO cell are reported. Major losses of iron units in froth products were in the -25µm (500 mesh) fraction, and the application of a magnetic field decreased the flotation of fine magnetite, thereby improving the selectivity of separation. The “as received” sample was sufficiently magnetized and no further benefit was gained by magnetizing treatment. Selectivity was somewhat adversely affected by demagnetizing the sample, though its effect was minimal due to the magnetic field. The device is simple in construction, low cost and may be installed readily in existing equipment.

Jan 1, 2002

By J. R. Gaw

Recent events pertaining to U. S. energy needs and development of alternative energy fuel resources have made the American public more aware of past and present coal mining operations, and their impacts on the nation's economy and environment. This awareness has developed rapidly due to increased government involvement and consequent media coverage. This is true particularly in the Western states and in Texas. One of the consequences of this increased public awareness is public concern over the perceived and real consequences of mining operations. Emphasis has been placed on potential releases of toxic and hazardous substances, and possible carcinogens. The result of this public concern is a mounting effort at both state and Federal levels to promote stricter laws regulating the mining industry.

Jan 1, 1992

By Francisco A. Fonseca

The Carajás Hills are in Brazil's Eastern Amazon, between the Araguaia and Xingu rivers, and parallels 5° and 7° Latitude South. A location map is given in Fig. 1. It is an area of low mountains (maximum altitude 900 meters), covered by the Amazon rain forest. Annual average temperature is 25°C, ranging from 31°C (maximum) to 19°C (minimum). Annual rainfall averages 2,000mm. Although it rains throughout the whole year, heavy rains occur from December through March. At the beginning of the 20's, Brazilian explorationists made brief geological descriptions of the area. Due to the thick soil, scarce fresh rock outcrops and the tropical forest covering a completely unpopulated area, detailed geological studies were difficult and reconnaissance expeditions were limited to the river margins.

Jan 1, 1982

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying an atomic force microscope (AFM) and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy to study in situ the adsorption of three different collectors — oleic acid, octanohydroxamic acid (HA) and salicylhydroxamic acid (SHA) — on bastnaesite in aqueous solutions. The results show that all three collectors adsorb on bastnaesite. The hydroxamic acid collectors — HA and SHA — adsorb on bastnaesite mainly in the form of insoluble metal hydroxamate. Their specific adsorption mechanism indicates that high selectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By J. W. Jang

The wear behaviors of grinding media with different chemical compositions and microstructures in wet grinding of a quartz-pyrrhotite mixture was investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation? behaviors. The galvanic interactions between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive conditions in a slurry. The rates of formation of passive films controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1989

By S. Philipp

This paper describes several variants of placement and design, from a technical and economic point of view, of shafts, ore bunkers and drifts near shafts of a Russian potash mine. Advantages and disadvantages of the position of different workings are shown as well as an analysis of stratigraphic and geological layers and their use for excavating pit bottoms, haulage drifts and bunker installations. The potash mine consists of two hoisting shafts and one service shaft. The hoisting capacity of one of these skip shafts is planned to be approx. 7 Million tons of crude potash salt per year. Both shafts together will have a hoisting volume of about 14 Million tons. When the mine will increase their highest level of production, it will be one of the biggest potash mines in the world. The skips, the hoist drives and the bunker near the shaft will belong to the largest ones worldwide, too. This paper specifies the features of such a double skip shaft pit in detail and demonstrates problems, which depend on the fact that the pit bottom is in a depth of nearly 1200 m.

Feb 23, 2014

By G. Miller

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixers. Recent experience with both large and small plants has shown that this is not the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers. Both of these lead to either reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Further, changes to the method of specification and selection of both primary and secondary mixers have been made to eliminate the onset of partial separation during operation. Observation of settler operation has shown that it is also a dynamic process, even under ‘steady state’ conditions. Four different transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze, and erratic and high entrainment levels in the discharges. A first approximation analysis has shown that there are significant pressure differentials within settlers and these change along the length and with phase separation rates. A technique to control the effects of these transients has been developed which allows plant performance to be improved beyond ‘standard’ expectations. The design and selection of the settler internals is described.

Jan 1, 2001

By J. Hupka

The limited effectiveness of the original hot water process for recovery of bitumen from certain Utah tar sands containing bitumen of higher viscosity (e.g. Sunnyside, Tar Sand Triangle)1,2 indicated that bitumen viscosity strongly' influences the separation efficiency. In this regard, there should exist a critical value of bitumen viscosity above which the effectiveness of the hot water process decreases significantly. Apparently certain tar sands contain bitumen of such high viscosity that even a digestion temperature of nearly 100°C is insufficient to lower the viscosity below the critical value. In addition it seems that differences in physico-chemical forces which act between sand and bitumen are negligible in comparison to the difference in visco-mechanical forces. Predominantly mechanical forces hold viscous bitumen on the rough surface and in the pores of sand particles, resulting in strong adhesion. This phenomenon is a critical feature in the phase disengagment of oil-wetted domestic tar sands with viscosity control by temperature. Besides increasing the temperature for viscosity control the effectiveness of the original hot water process could be enhanced by control of bitumen viscosity with diluent additions. Strictly speaking this appraoch is the only possibility for heavy bitumen for which the high temperature of digestion does not lower the viscosity sufficiently. As a result of viscosity control by diluent addition the digestion temperature can be lowered which is important from an industrial standpoint. Another important consideration is that effective phase disengagement occurs only when the entire bitumen phase has the same viscosity. This means that some time (penetration time) is necessary for complete and uniform dilution of the bitumen. If the viscosity of bitumen, which is a function of temperature, diluent addition and penetration time, controls the separation efficiency, hot water processing of many different kinds of tar sands should be possible, assuming that the sand phase consists primarily of quartz-type minerals.

Jan 1, 1982

By J. E. Kogel

Industrial minerals play a central and dual role in the sustainable development (SD) of natural resources. Over the past decade the mining industry has increasingly focused on sustainably extracting and processing industrial minerals. This trend has been driven by higher energy costs, diminishing water resources and sensitivity towards environmental stewardship. Industrial minerals have been used throughout human history as low cost, naturally occurring, materials. Today they are critical components of recycled packaging, energy efficient building materials, light weight paper coatings, and other products critical to the responsible utilization of global resources. As industrial minerals become more widely used in ?green? products, mining companies have established best practices for the sustainable management of industrial minerals mining and processing. These management practices include reducing energy consumption, minimizing water usage, increasing waste recovery through recycling and process optimization, and maximizing the amount of ore extracted per acre of disturbed land. With the commitment to SD principles, quantitative methods for objectively measuring SD performance have become increasingly important. Measuring sustainability impact is a valuable tool for effectively applying SD principles and for making choices that balance sustainable development against other business objectives. SUSTAINABLE DEVELOPMENT AND MINING Sustainable development is a term that has become a common part of our lexicon; however, it has multiple meanings and interpretations leading to a sometimes confusing and contradictory array of definitions. The absence of a single, precise definition reflects the fact that SD is a broad concept or paradigm that offers guiding principles as opposed to a specific set of criteria or regulations enforceable by government or other oversight agencies. While a principle based conceptual approach allows businesses to broadly apply SD practices that are tailored to their specific situation, it has also led the public to sometimes view voluntary corporate SD programs with a degree of skepticism (Walker and Howard 2002). This is particularly true in the mining industry. One reason for this skepticism is that the relationship between SD and mining is misunderstood and to many, sustainably developing non-renewable mineral resources is a contradiction (Rajaram et al. 2005). However, this view takes a very narrow interpretation of the tenets of SD. The second is that mining carries a legacy of poor environmental stewardship that does not accurately reflect current corporate environmental practices Many minerals companies have adopted the Brundtland Comission?s definition of SD (United Nations 1987): ?? development that meets the needs of the present without compromising the ability of future generations to meet their own needs?. This definition is very broad and can be interpreted in a number of ways. It provides a general context for sustainable development and is not intended to provide detailed guidelines addressing specific aspects of sustainable development. To fill this gap the following SD principles were drafted by the international minerals community in 2003 (ICMM 2003): 1. Implement and maintain ethical business practices and sound systems of corporate governance. 2. Integrate sustainable development considerations within the corporate decision-making process. 3. Uphold fundamental human rights and respect cultures, customs and values in dealings with employees and others who are affected by our activities. 4. Implement risk management strategies based on valid data and sound science. 5. Seek continual improvement of our health and safety performance. 6. Seek continual improvement of our environmental performance. 7. Contribute to conservation of biodiversity and integrated approaches to land use planning. 8. Facilitate and encourage responsible product design, use, re-use, recycling and disposal of our products. 9. Contribute to the social, economic and institutional development of the communities in which we operate. 10. Implement effective and transparent engagement, communication and independently verified reporting arrangements with our stakeholders. These guidelines insure that SD concepts are applied equally across the industry while setting a clear performance standard and benchmark against which to evaluate success. By adopting these principles and issuing the Milos Statement (http://www.sdimi.org/milos_decl_October%206_2003.pdf), which provides a more detailed vision for integrating SD into everyday business operations, the minerals industry has embraced SD as a core corporate value. The unifying and holistic approach embodied in SD principles impacts the entire mine to market life cycle and addresses the economic, environmental and social consequences of mining. INDUSTRIAL MINERALS The world economy relies heavily on minerals; they are essential to economic prosperity and the quality of life. Industrial minerals are non-metallic, non-fuel minerals that provide the raw materials for a vast range of products used in most every aspect of daily life. They are mined and processed worldwide and they span the spectrum from relatively low value, high volume commodities (e.g. common clay, crushed stone) that are usually mined locally to high value, low volume specialty materials that are sourced from unique one of a kind deposits (e.g. barite, talc, mica). High volume commodity mining operations are often located near the end use market which, in most cases, means areas of high population density where construction and other urban activities drive demand. In these situations the strict adherence to SD principles is particularly critical as these are highly visible operations that must meet the public?s demand for good corporate citizenship. These operations are similar to chemical or other manufacturing facilities that operate near population centers. In contrast, some mining operations are located in remote but environmentally sensitive regions of the globe where the pressure to mine sustainably is driven by the need to preserve habitats and other

Jan 1, 2009

Due to deposit shape and dimension, narrow vein makes reserve modeling, geological control, stope design, drill and blasting more challenging. It needs high standard quality control as errors can be created easily, which could cause significant amount of ore loss or dilution. From channel sampling, survey control, reserve modeling, drill hole design, blasting, communication with underground drillers to backfill, this paper illustrated every step and its quality control of a long hole stope mining. Compared to other narrow vein mining methods (cut and fill and shrinkage), long hole stoping means higher production, less labor, and significantly lower cost when deposit characteristics allowed.

Jan 1, 2012

By S. C. Sethi

The paper presents an analysis and discussion of the underground ventilation system at the waste Isolation Pilot Plant (WIPP), with particular emphasis on specific repository-related requirements and the gradual evolution of engineering designs relative to the WIPP Project scope. The underground facility has been constructed with three shafts. Additional studies, coupled with actual site-specific experience, have established? the need for construction of a fourth ventilation shaft to double the under-ground airflow. As a research pilot project, and the first of its type in combining mining and nuclear technologies, the WIPP Project is accumulating data and experience that may be fruitfully applied in the future designs of ventilation systems for planned commercial nuclear waste repositories.

Jan 1, 1988