Search Documents

By R. L. Grayson

Following lip on a USBM-sponsored research project, the authors have utilized the knowledge-base structure and system concepts from the Sun Sparcstation-based worker scheduling system of the Mine Management Support System to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, their availability on a shift, and work priorities for a shift as well as to allocate manpower optimally on a work shift and delineate supervisory training responsibilities. The various components of the software are described in detail, along with enhancements made to the original system.

Jan 1, 1996

By N. Dashbold, E. Rudnik

"Waste electric and electronic equipment currently comprises the fastest-growing waste stream in the world, but at the same time it is seen as an important source of metals for the recycling industry. E-waste is usually treated pyrometallurgically, with hydrometallurgical methods used to a lesser extent. This paper reports the results of research on the selective recovery of copper from smelted low-value electronic waste. Pyrometallurgical pretreatment of the scrap allowed the removal of plastics and the increase of metal content in the material. The obtained alloy of copper, zinc, tin and silver was a multiphase solid consisting of two brass phases and inclusions rich in iron, lead and silver. Copper alloy was further anodically dissolved in ammoniacal chloride solution. It resulted in high degradation of the material and accumulation of the metals mainly in the slime. The slime was then leached in acid or ammoniacal chloride and sulfate solutions followed by selective copper electrowinning. Hydrochloric acid was the most efficient solvent for the slime, but ammoniacal solutions were more selective for copper. Copper could be leached with 96 to 100 percent and 87 percent efficiency from the slime by the chloride and sulfate solutions, respectively. Copper with 90 to 99 percent purity at current efficiency of 42 to 76 percent was obtained from the acid solutions, while copper with 98 to 99 percent purity at current efficiency of 60 to 86 percent was deposited from the ammoniacal baths. IntroductionObsolete electrical and electronic equipment makes up the fastest-growing waste stream in the world (Baldé et al., 2015), due not only to the introduction of wider ranges of new types and models of a variety of electronic products but also to the shortening of their life-spans, sometimes referred to as planned obsolescence by producers (Keeble, 2013). About 42 million tons of electronic waste, or e-waste, are estimated to have been generated globally in 2014 (Baldé et al., 2015), and it is expected that in the European Union alone the waste electrical and electronic equipment (WEEE) stream will reach more than 12 million tons by 2020 (European Commission, 2015). Accurate evaluation of e-waste generation (Wang et al., 2013) and its global transport (Breivik et al., 2014) is difficult, mainly due to a lack of high-quality data related to its market and socio-economic dynamics.Many countries introduced legislation to control e-waste flow, collection and recycling. For example, Directive 2012/19/EU on waste electrical and electronic equipment (European Parliament and the Council of the European Union, 2012) obliges all E.U. members from 2016 to maintain a minimum collection rate of 45 percent of the total weight of WEEE collected. From 2019, the minimum collection rate to be achieved annually shall be 65 percent of the average weight of electronics placed on the domestic market in the three preceding years, or alternatively 85 percent of WEEE generated in the territory of the particular member."

Jan 1, 2017

By J. -F. Lagueux

Goldex Mine is an underground mine located near the town of Val-d?Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long hole stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23 Mt of ore, large blasts up to 1.8 Mt are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km radius of the mine site. In addition to managing mass blasts, means must also be found to mitigate the vibrations produced by the blast to diminish the disturbance to the neighbourhood. Therefore, the mine used numerous tools to properly plan the blasts and reduce the impacts. A program to control vibrations was one of the first tools put in place. The program?s aim was to draw up an action plan to ensure a follow-up of the homes by inspecting them. The second tool was to develop a methodology to plot a reliable attenuation curve and to adequately determine the maximum charge weight for each blast. Finally, effective communication tools were developed to inform the neighbourhood. There was a huge amount of work to be done in relation to the bench. Reliable and fast loading techniques had to be found to load large blasts in a very short period of time. Adequate logistics had to be developed to send underground more than 20,000 kg of emulsion per day while performing the daily underground operations. Technology had to be developed to adapt the i-kon electronic blasting system to large blasts. Since the control of the charges was the major factor to reduce surface vibrations, it was important to employ loading techniques that would permit decking of the long holes to reduce the charge weight per delays without adversely affecting the loading. All of this work requires an enormous amount of energy but also close collaboration between the different stakeholders (various departments, suppliers and consultants).

Jan 1, 2011

By A. M. Gaudin

The recent study by R. M. Hays(l) prompted the study summarized in this paper. In his Interesting paper, Mr. Hays shows fine results to be attainable by a relatively complex flowsheet on a semi-taconite, a manifestly difficult ore to treat. We obtained a semi -taconite from Minnesota, and treated this sample by wet magnetic separation alone. The device in which the separation was accomplished is the standard pilot-plant, laboratory separator in use at Magnetic Engineering Associates' laboratory (MEA) in Cambridge, Massachusetts. It consists of a cylindrical space which can be magnetized by turning on the magnet of the separator. In this cylindrical space, there is a canister which provides the special configuration of the magnetic field and magnetic field gradients that MEA considers to be required. The ore pulp is made to flow through the canister while the current is on. A portion of the pulp is retained in the canister, and the rest is evolved as a non-magnetic fraction. The laboratory device is cyclic, but it accurately predicts the results obtainable by an Industrial unit of either cyclic or continuous type (moving matrix). The ore tested was 99.5°%o -325 mesh, and approximately 75% -500 mesh. The concentrate from this ore was, therefore, eminently suitable for pelletizing. In passing the ore through the magnet, we had the choice of repeatedly passing the concentrate from the first step through the operation, or of repeatedly passing the non-magnetics. In our experiments, the first method was clearly superior from the stand¬point of the cleanliness of concentrate. Of the many tests which we have made, we think that we have to retain two which

Jan 1, 1971

By M. Robson

Water & Earth Technologies, Inc. (WET), Habitat Management, Inc. (HMI) and Chevron Mining, Inc. (CMI) together developed a solution for reclaiming steep southwest facing slopes in mining Area 12C that have historically been prone to excessive erosion, low vegetation establishment and continuing maintenance. Area 12C is located in the east wing of the Chevron McKinley Coal Mine, 27 miles northwest of Gallup, New Mexico, on Navajo Nation land administered by the Office of Surface Mining (OSM). Mining in this area was completed in May of 2007. Challenges encountered for this reclamation project included the need to reclaim graded material on a slope of 18-35% with southwest facing aspect, the presence of undisturbed rock outcropping that needed to be avoided during reclamation, the operational need to limit bulldozer pushes and the inability to import or export additional materials for construction. Two different reclamation alternatives were considered for Area 12C. The first alternative would use a traditional reclamation approach including three levels of draining terraces designed to convey water on a 3% slope to a single riprapped down drain. Terracing and down drains have been used to reclaim areas with similar terrain conditions elsewhere at the McKinely Mine and have failed to adequately control erosion (Williamson 2006). Terrace overtopping and down drain blowouts have been issues in maintenance and functionality for the mine. Maintenance routines consist of cleaning out terraces where they have filled in with sediment and repairing damaged or blown out terraces and down drains.

Jan 1, 2010

U.S. Borax’s mine in California’s Mojave Desert is the source of nearly half the world’s supply of refined borates. These minerals are used in hundreds of products, including essential plant nutrients that increase crop yield and quality, and safe building products that protect homes from insects and the elements. Borax’s workforce is also safe. In fact, it is among the safest in the nation. In 2003, the company was recognized by the U.S. Mine, Safety and Health Administration (MSHA) for achieving the best safety record among large U.S. mining operations. It was also recognized by its parent company, Rio Tinto, for achieving the best record among its nearly 80 worldwide mining operations. Borax’s safety performance is five times better than the national average. And its workforce recently achieved more than two million hours without a lost-time injury.

Jan 1, 2004

By Thomas P. Goslin

T e mechanization of industry to reduce labor costs and to improve product quality is affecting he scale industry as it has affected many other industries. With increased emphasis on higher production rates many operators are experiencing difficulty in overcoming production problems where weight is a factor. Unfortunately, the scale industry has not shown the development over the last twenty-five years that other instrument industries have. For centuries the balance scale has been the standard and the workhorse of most weighing operations. In recent years considerable effort has been applied to designs to make balance scales more acceptable to industries employing automatic or semi-automatic processes. For the most part the designers have not attempted to replace the basic scale but toautomate functions of material handling and human judgement. Modern dump scales, for example, will accept material from a conveyor until a preset amount of material is on the scale, At this time the scale turns off the conveyor, dumps the load of material and repeats the operation with any desired timing. These improvements have helped industry. Even the scale observer has been replaced with devices which observe the scale reading and operate on weighed objects according to their weights. In spite of' the application of automation to the material handling, the balance scale has not been completely satisfactory. One reason for this is fairly evident when one considers the construction of the scales. Inherently, they are slow devices because of the inertia of the beams. The beam scale, primarily a static measuring device, is at the best limited to slow dynamic measurements.

Jan 1, 1958

By Zhan-fang Cao, Hong Zhong, Li-feng Li, Shuai Wang, Xiao-yu Cao, Guang-yi Liu, Ming-ming Wang

"In recent years, there has been an increasing focus on the hydrometallurgical processing of molybdenite, with the decline of high-grade and easily handled molybdenum minerals. In this work, a novel method of selective extraction of complex molybdenite concentrate, which is characteristic of high-grade copper ore, has been investigated. The results show that the leaching of chalcopyrite was impacted by the pH of the electrolyte when sodium carbonate and ammonium acid carbonate were added to the electrolyte. The leaching rate of molybdenum reached 99.39%, but chalcopyrite could not be leached at all in 240 min under experimental conditions of liquid-to-solid ratio 25:1, concentration of NaCl 4 mol/L, pH=9, room temperature and agitation speed 400 rpm. The grade of copper in the residue was 21.84%, with a recovery 99.93%. The technology of selective electro-oxidation leaching of molybdenum and recovery of copper from complex molybdenite concentrate is an effective separation method. The diffusion control model can be used to describe the process of leaching of molybdenum. The activation energy of the leaching reaction was found to be approximately 9.21 kJ/mol.IntroductionWorldwide, high-grade and easy-to-handle ore is decreasing, while the proportion of low-grade and complex ore is increasing. Porphyry copper ores with associated low-grade molybdenite are very abundant in China. Molybdenum is a valuable byproduct in the processing of porphyry copper deposits where the molybdenum is present in low quantities in the form of molybdenite (MoS2). In the conventional processing of copper sulfide ores by froth flotation, most of the molybdenite in the ore floats along with the copper sulfides. In this way, a bulk copper-molybdenum concentrate is produced. Afterward, the bulk coppermolybdenum concentrate is treated by differential flotation to obtain a rougher molybdenum concentrate, which requires several successive cleaning steps to produce a final molybdenum concentrate. However, it is widely recognized that flotation alone cannot economically produce a high-grade molybdenite concentrate, i.e., with less than 0.5% Cu. Therefore, in most cases, it is necessary to use a final step of chemical purification of the molybdenite concentrate to reduce the copper content to a level suitable for the market (Antonijevic and Pacovic,1992; Gerhardt et al., 2001; Fu and Zhong, 2003; Reza et al., 2006, Rafael et al., 2013)."

Jan 1, 2015

By Mads Aniksdal

New Nedre Fiskumfoss is a construction project in North Trøndelag, Namsen River. The purpose of the contract is construction of a new hydropower plant, that will phase out the existing power plant in the same waterfall. The contract consists of a tunnel system with cross sections from 16 m2 to 150 m2, powerhouse and transformer in rock caverns, 6 shafts and major works with inlet and outlet below river level. Technical challenges consist of demanding design on rock extraction, cofferdams, solid constructions with challenging design and demanding rebar work, as well as restrictions and unpredictable water flow in a national salmon river.

Jun 13, 2023

By Arthur G. Strassburger

INTRODUCTION High in the Sierra Nevada Mountains of California, some 50 airline miles (80 km) northeast of Fresno, and near the John Muir Wilderness and Kings Canyon National Park, a large underground hydroelectric project is under construction. Pacific Gas & Electric (PG&E) Company's 1,125 MW Helms Pumped Storage Project exhibits a number of impressive statistics, unusual features, and other characteristics of interest to the tunneling or power plant designer and construction contractor. The most significant underground facilities include almost 20,000 ft (6,096 m) of 27-ft (8.2 m) diam concrete-lined pressure tunnel; 3,700 ft (1,128 m) of access tunnel; 1,600 ft (488 m) of steel-lined high-pressure conduit, 2 major underground chambers more than 1,000 ft (305 m) below ground; 3 deep vertical shafts, and one steep inclined shaft. Maximum static pressures within the conduits range from 200 ft (61 m) to 1,744 ft (532 m), with hydraulic transients that increase pressure to 2,500 ft (762 m). The purpose of these underground works is to provide 475,000 hp (354,350 KW) of water power to each of the 3 reversible pump-turbines, each connected to a 375 MW generator motor. The units, rated at 1,744 ft (532 m) maximum static head, are among the world's front-runners, considering the size-head combination. The Helms Project develops the existing power drop between two of PG&E's reservoirs, Courtright Lake and Lake Wishon. These reservoirs are retained by two concrete-faced rockfill dams completed in 1958, each storing approximately 125,000 acre ft (154 x 106 m3) of water. Although the project is intended to operate on a typical

Jan 1, 1981

There are multiple stages in a mining operation that a mining engineer has to draw polygons to be used as operation guidelines. These polygons are drawn by hand and based on engineer?s experience. However, having automatic procedures for forming the shapes can increase the quality and decrease the efforts required. These shapes need to be homogenous in grades and rock types so that the quality and dilution of material sent to the plant can be estimated with the good approximation. In this paper, a clustering algorithm with shape control is introduced which can provide reasonable guidelines for all the aforementioned shapes by manipulating its parameters. At the end, implementations of the algorithm on a small part of a gold deposit with different mining strategies is presented and evaluated based on homogeneity of grade, rock types and determined destinations as well as the shape.

Feb 27, 2013

By A. S. C. Owili-eger

An efficient state-of-the-art dynamic model to simulate and predict the rate of water production in longwall coal mining operations was developed as a tool for mine planning purposes. The model can also provide an estimate of any potential resultant hydrogeological impacts of an operation via an array of element-specific single-valued parameters referred to as the field rating indices. The computational procedure was designed to fully exploit the benefits of hydrogeotechnology and utilize a combination of conceptual, physical, empirical, and numerical approaches to define, characterize, analyze, and evaluate flow con- trolling properties of fractured rock systems. The model presented here provides a dynamic prediction method for highly fractured flow; a practical tool in mine and water control planning; and a cost-effective means of assessing, based on the best available technology, the impacts of mining on the water resources within a mining environment to satisfy local and federal regulatory requirements. Unique features include consideration of laminar and non-darcian flow domains in double-porosity-pressure hydrogeological media.

Jan 1, 1987

By Fulian He, Jianhang Chen, Dongdong Chen, Shoubao Zhang

"The Wangjialing Coal Mine is the main colliery of the China Coal Huajin Energy Limited Liability Company. The average thickness of the coal seam in District 201 is 6.21 m. Fully mechanized longwall mining was used in this district. The ventilation roadway of panel 20102 was influenced by the retreat mining of the adjacent panel 20104. Therefore, large deformation and severe roof falls occurred in this roadway, seriously influencing the safety production of this coal mine. To support the roadway, cable truss was proposed to strengthen the reinforcement of this ventilation roadway. First, numerical simulation was used to optimize the reinforcement parameters, including the cable installation angle, cable length, and eccentric distance. Based on numerical simulation results, in-situ tests were conducted in the ventilation roadway of panel 20102 with the cable truss technology. In-situ monitoring results showed that the roof-to-floor convergence and the convergence of roadway on two sides were within the safety range. Furthermore, no apparent separations occurred in the roof. These indicate that based on the designed parameters, the cable truss system can effectively maintain the roadway stability under the severe influence of the adjacent longwall mining.INTRODUCTIONCable bolts are flexible tendons composed of multi steel wires, which are wound into a strand (Chen, Hagan, and Saydam, 2018). They were initially introduced in the hard rock mining industry in the 1960s. Later, they found rapid application in coal mines to maintain the stability of excavations (Wang et al., 2015).The standard cable bolt is composed of seven steel wires with a diameter of 15.2 mm. Laboratory and in-situ tests showed that there is a low bonding capacity between the standard cable bolt and the grout (Craig and Holden, 2014; Chen, Hagan, and Saydam, 2018). Then, modified cable bolts are developed based on the standard cable bolts. They are improved by changing the surface geometry of standard cable bolts, such as birdcaged cable bolts (Hutchins et al., 1990) or nutcaged cable bolts (Hyett et al., 1993). Further tests proved that modified cable bolts have better mechanical interlock and friction between the cable bolt and grout, leading to larger load transfer capacity of cable bolts.Although cable bolts have been used for many years, failure of the cable bolting system still occurs. A common failure mode is the damage of surrounding confining medium while the cable bolt is still hanging in the roof, which is caused by the bond failure of the cable/grout interface (Hutchinson and Diederichs, 1996). To prevent the cable bolting system from failing, the cable truss system is more widely used in mining engineering."

Jan 1, 2019

By L. L. Chasko, D. W. Alexander

Los investigadores del National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research han evaluado los efectos que la malla de control de suelos podría tener en la distribución de polvo flotante de roca y carbón en minas de carbón. El creciente uso de mallas para controlar el desconchado o caída de material del techo y las vigas introduce superficies elevadas adicionales para recolectar el polvo de roca o de carbón. Es posible que el potencial para la propagación de explosión del polvo se incremente si el polvo flotante de carbón no es convertido en inerte de manera adecuada. Adicionalmente, la malla podría interferir con la recolección de muestras representativas de polvo cuando se usa el método de recipiente y brocha desarrollado por la U.S. Bureau of Mines y usada por la Mine Safety and Health Administration para muestreo de banda. Este estudia hace una estimación del polvo de roca o carbón adicional que pudiera acumularse en la malla y desarrolla un método para recolectar muestras de polvo representativas atrapado en las mallas.

Jan 1, 2014

By D. D. Rabb

Originally, the term solution mining applied to a dissolution, washing, or "brining" of soluble salts such as halite (common table salt), potash or trona. After the mid-sixties, however, the definition has been expanded to include heap and dump leaching, in-place (in situ) leaching, removal of oil from tar sands, extraction of sulfur from deep wells by the Frasch process and the recovery of metalliferous solutions from geothermal sources. Solution mining is also known as borehole, non-shaft, or chemical mining; the extraction of soluble mineral values from a variety of ores using appropriate solvents and chemicals. Solution mining frequently involves chemical changes; for example, copper usually goes into solution as copper sulfate, gold and silver as a cyanide compound, and uranium as a sulfate or uranyl tricarbonate. The valuable constituent is removed from the solid body of the ore by mass transfer to a aqueous solution.

Jan 1, 1986

By Young C. Kim

In the past, underground coal mine planning has traditionally focused on the mine design n aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most of the underground coal mines within the U.S. With the enactment of the clean air act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the BTU contents of coal are of equal importance from boiler efficiency standpoint. Thus, the time has come when the coal mine planning must incorporate the coal quality control aspects as well as the traditional safety and efficiency aspects.

Jan 1, 1983

By Ivan V. Klumpar

If components of a gas-liquid stream react with each other and with stationary solids, involving parallel and sequential, reversible and irreversible, and slow and instantaneous reactions, the process can be defined by a set of simultaneous differential rate equations and simulated as multistage semibatch re¬actors. Each stage is divided into finite time increments. Within each increment, even the simultaneous reactions are treated as sequential. The proposed method follows process evolution from non-steady state startup to normal operating conditions. It allows computing byproduct buildup in recycles, tracer response curves and, in case of underground processes, expansion to adjacent parts of the deposit.

Jan 1, 1979

By S. A. Moffatt

For several years iron ore processing plants, located in the northern U.S. experienced seasonal decreases in the grinding efficiency of their primary autogenous mills. Kawatra and Eisele (1992) studied this phenomenon in an operating plant and characterized it in terms of specific energy consumption (Fig. 1) and production of critical size material (Fig. 2). Critical size material is defined as ore that is too small to be effective grinding media and too large to be ground. This data showed that both specific energy consumption and critical size production increased during the winter months. The increased energy consumption was in part a result of an increase in the viscosity of the mill pulp at colder pulp temperatures. However, viscosity could not fully explain the changes in critical size production. These changes are most likely due to changes in the breakage characteristics of the ore. Other studies were also conducted to determine if thermal and physical properties of iron ore changed at colder temperatures. These are summarized below:

Jan 1, 1993

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022

By Paul D. Tavares, John Forbes, Eric R. Drooff

As the existing major U.S. - Canada rail tunnel was too small to accommodate double-stack container cars, Canadian National Railways is constructing a new parallel tunnel with a 50% greater diameter. Starting in Sarnia, Ontario, the new shallow-cover bored tunnel runs under a large research building and several other structures in an oil refinery before travelling under the St. Clair River. Maximum predicted settlements to be caused by the 9.2 meter diameter earth pressure balance TBM in the soft St. Clair till were in excess of 100 millimeters. As such, these settlements had the potential to cause severe damage and disruption to the existing refinery. In order to reinforce the soft clays below the refinery research building and other structures, and to compensate for settlement caused by the tunnelling, the ground improvement method of Soil Fracture grouting was successfully applied for the first time in North America. This paper will describe the details of both the soil fracture grouting application and the elaborate electrolevel remote monitoring system used.

Jan 1, 1995