Search Documents

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, B. D. Ganesh Shetty, M. RAJU

The production of high strength iron ore sinter for blast furnace iron making unit was developed by optimizing the granulometry of less than − 0.150 mm fines in sinter base mix which consists of iron ore fines (− 10 mm size with 0.150 mm: 41%), beneficiation plant jig concentrate, i.e., washed ore (− 3 + 0.150 mm size with − 0.150 mm 3 to 9%), beneficiation plant concentrate (− 0.150 mm size 97%), limestone, dolomite, coke breeze, lime, sinter return fines, direct reduced iron (DRI plant) fines, and micropellets produced from steel plant waste. The sintering process consists of preparation of base mix, mixing, and production of nodules using mixing and nodulizing drum by maintaining the optimum moisture, transferring of nodules to the sintering machine, and firing of sinter by applying optimum suction pressure. To optimize the < 0.150 mm fines in sinter base mix, the − 10-mm size iron ore fines was replaced with washed ore. The size analysis, granulation index (G index), and optimization of moisture w.r.t. sinter bed permeability were carried out by varying the washed ore addition from 0 to 55% in sinter base mix to vary the − 0.150 mm fine size. With decrease in washed ore addition from 55 to 0% in sinter base mix the finer fraction, i.e., − 0.150 mm in sinter base mix increased from 9.4 to 26.7%. Granulation (G) index increased from 1.46 to 3.10, sinter bed permeability increased from 33 to 53 Japanese Permeability Unit (JPU), and balling index increased from 1.4 to 3.0. With increase in − 0.150 mm fines in the sinter base mix from 9.4 to 26.7%, the sinter tumbler index (T.I) increased and sinter reduction degradation index (RDI) decreased. Increase in sinter strength and decrease in sinter RDI was due to increase in formation of Silico ferrite of calcium and aluminium (SFCA) phase and decrease in pore phase. The SFCA is the main bonding phase in iron ore sinter, and it provides strength to sinter. Sinter base mix with − 0.150 mm fines 18.9% (washed ore addition 25%) achieved desired sinter properties with moisture 8.0%, G index 2.44, balling index 2.3, and sinter bed permeability > 45JPU. Decreased the sinter properties with washed ore addition in sinter base mix beyond 25% due to decrease in − 0.150 mm fines in sinter base mix. Further, to improve the sinter properties with washed ore 30 to 45%, 3 to 10% beneficiation plant concentrate, i.e., − 0.150 mm fines was added to maintain the 18.9% of − 0.150 mm fines in sinter base mix. From the laboratory sintering studies, it was found that minimum 18.9% (range from 18.9 to 26.7%) − 0.150 mm fines should be maintained in the sinter base mix to achieve desired sinter properties.

Oct 16, 2021

By Wayne W. Murdy

Since 1993, Newmont has been actively growing through the development of three major foreign mining operations with a fourth under construction. The first project, Yanacocha in Peru began operating in October 1993 at a time when political and business risk in that country was considered high. In 1995, Newmont began operating the Muruntau Joint Venture in Uzbekistan, the first of its kind in the CIS. In early 1996, Newmont started operating the Minahasa mine in Indonesia. Now, in early 1997, Newmont is undertaking the construction of a $1.9 billion project in Indonesia and is completing a feasibility study with our partner for the development of a gold operation in Mexico. All of these projects have been considered "risky" by most standards, and Newmont has been very successful in all of them through risk mitigation programs including utilizing strong and successful in-country partners, concentrating on developing a strong national workforce with minimal expatriate employees, utilizing World Bank, EBRD and IFC financing and building and maintaining strong ties with host governments. This paper describes in more detail, some of the risk mitigation programs that Newmont has used to successfully grow the company through development of major foreign mining operations.

Jan 1, 1997

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By Hans W. Schreiber, Rudi P. Fronk

IINTRODUCTION Widespread activities in precious metal projects in the western U.S., Australia, Canada and other parts of the world have opened a flood-gate of consul- ting expertise to aid and accelerate the development process. Utilization of outside expertise has taken on many shapes and forms that have in some instances actually "decelerated" or "retarded" project progress. Small mines are especially vulnerable to apparent false-starts and misdirections, be- cause of their generally lower capital commitments, shorter lead times and limited mineral in-house expertise. Mine development for small mines requires fundamental approaches by knowledgeable consultants that are timely and cost-efficient and in line with accelerated development, if they are to be successful. The development process is obviously that process which brings a given deposit into production. Or, put another way, the process comprises all activities, decisions and commitments which take place from the moment an authorizing entity (usually a board of directors) com- mits to development and production (usually on the basis of a final feasibility study) until the first ton of ore is processed to a saleable product. The activities, decisions and commitments over a development period--such a period can range from as short as a year or less to as long as 5 years or more--are many, highly varied, and often interdependent. The development period is also particularly risky, not only because of the varied and interdependent decisions and commitments, but also because of capital demand amounts. Delays in the development process are thus particularly costly - sometimes so costly that small and often undercapitalized mining companies, failing to reach production and a cash flow within a planned period, face, if not bankruptcy, at least severe equity dilution or particularly onerous and restrictive covenants on additional loan financing. It therefor behooves especially small mining companies to examine ways to accelerate development. By doing so, the development process may actually meet planned scheduling. The development process generally comprises environmental impact studies completion, final engineering, permit- ting, financing, equipment and machinery procurement, contractor selection and construction -- such activities largely being overlapping. The paper addresses what the small mines operator or the small mining company can do with consulting firms to accelerate development. By "small mines" is meant open pit operations of 2000 tpd or less and underground operations of 500 tpd or less. By "consulting firms" is meant entities who do not possess an engineering and construction capability, such as Derry Michener Booth & Wahl, Pincock Allen & Holt, Behre Dolbear-Riverside, etc. The paper concentrates on gold projects. PRIORITY CONSIDERATIONS Of the items listed in the previous paragraph which comprise the development process, the two which most consistently appear to cause delays are permitting and financing. The former&apos;s delays can be due to political overtones and thus the delays may not be reasonably foreseeable. The latter&apos;s delays are most often due to inadequate preparation, and thus are avoidable. For the reason stated above, and considering that financing is fundamental to all of the activities which constitute the development process, the paper focuses on financing as the priority item which can most assist in accelerating or retarding the development process.

Jan 1, 1987

By D. L. Leach

This report covers laboratory experiments simulating in situ copper recovery from primary sulfide ores in sulfuric acid systems pressurized with oxygen. Copper extraction and acid consumption data are correlated with temperature in the range 50-150°C and quenched pH in the range 0.25-2. Adverse changes in the chemical composition of the leach solution and the formation of gangue-mineral alteration products and secondary sulfides can severely limit the extraction of copper above 90°C. Keeping the pH below the self-buffered value of about 2 and the temperature below about 110°C produces the maximum extraction rates. Forcing the pH too low not only results in excessively high acid consumption but may also limit the extraction of copper at temperatures above 100°C.

Jan 1, 1975

By Dan Nilsson

The Luossavaara "Research Mine" is the First large, offensive effort in mining research conducted by the Swedish state. Over a 5-year period, 1981-1985, the Swedish Mining Research Foundation works in the "Research Mine" on the development of mining systems and equipment. The purpose is to bolster the competitive strength of the Swedish mining and mining equipment industry. The previosly abandoned Luossavaara mine in Kiruna, in northern Sweden, has been reopened especially For the project. Ore is mined and sold during the course of the research project. The income from the sales covers a large portion of the costs for teh research.

Jan 1, 1985

By Arthur M. Ribe

In my experience, nothing helps me better to get off to a good start in preparing a paper or a talk than a copious consultation with a comprehensive dictionary. I also feel defining the perimeters of a particular subject is helpful to the listener and reader. Sometimes thus precisely defining even the most common of words is helpful. Our general topic this morning as all of you know is "Transportation of Industrial Minerals." The definition of transportation given by the dictionary which I think is appropriate here is: "Systems and modes of conveyance of persons or goods from place to place." Our preceding panelists have outlined for you the state of the art inso¬far as systems and modes of conveyance from place to place are concerned today via rail, water and motor. My assignment is somewhat different as indicated by my topic, "The Traffic Manager in an Industrial Minerals Operation."

Jan 1, 1969

By J. A. Lombardi

Acid-Minesite-Solutions (AMS) are defined as copper-containing pit lake, tailing pond, acid-mine-drainage, and heap and waste dump irrigation solutions. All of these solutions are characterized by copper, acid and water contents that have value as individual commodities. HW Process Technologies, Inc. (HWPT) has developed nano- and hyper-filtration membrane methods for the separation of copper and other base metals, acid and water from AMS. These treatments are collectively called HWPT?s Engineered Membrane Separation® (EMS®) systems. The EMS® method of copper recovery produces small volumes of higher-concentration copper solution from large-volume, copper-dilute AMS. A case study of the 4,000 gpm Cananea EMS®-AMS plant for the recovery of copper from an acid-pit-lake resource is described. The EMS® method of copper removal from AMD and tails pond waters has been bench-scale demonstrated and are described, complete with projected budgetary capital and operating costs. Additional treatments for the recovery of sulfuric acid and high-quality water from the permeate (membrane passing) waters for the above-described AMS treatments are presented, with budgetary capital and operating cost estimates. [ ]

Jan 1, 2009

By M. Xing, S. Usman, K. Awuah-Offei

"While mines generally focus on achieving operational efficiency, creating shared value for all stakeholders is also a management goal. This includes taking a holistic view of their supply chains and increasing local participation. This paper examines the role of supply chain management in mine management; in particular the effect of a strong local supply chain on regional economic impacts. Using input-output analysis, the impact of a local supply chain on a mining sector’s regional economic impact is examined by increasing local sourcing (increasing local purchase percentage -- LPP) for 10 key commodities. An approach, based on multipliers and excess local capacity is used to identify key commodities. The impacts examined are sales, employment, labor income, and value added. The work is illustrated with stone mining and quarrying in Missouri. Ten percent increases in LPP of the key commodities, in this example, result in $4.1 million additional impact on the Missouri economy. This work can provide insight on how to better create shared value for all stakeholders. INTRODUCTION Little research has been published on improving mine supply chain management (SCM) to enhance regional economic impacts. Although some extensive academic research has explored the importance of an industries’ supply chain, not much is known about how a locally-based supply chain increases shared value in the resource sector. Across industries, traditional SCM is getting more and more complex. This is true of the mining sector as well. However, this increased sophistication is not directed towards increasing shared value for all stakeholders, particularly, the local communities. Further research is required to develop new SCM strategies that enhance local participation. One major point of difference between this work and traditional supply chain management is the inclusion of stakeholders’ shared value as a goal in SCM. Creating shared value has become a business goal in recent years (Porter and Kramer, 2011). The authors use input-output analysis (Leeuw, 2012) to evaluate the regional economic impacts of supply chain decisions, which is not part of traditional SCM. Although input-output analysis has been applied to SCM for decades, most of the research uses input-output analysis as a tool to advance an industries’ own operational efficiency (Accenture, 2014)."

Jan 1, 2015

By Dolf Vos

The balling section of the pelletizing plant at Hoogovens IJmuiden consists of 7 balling drums. Each with an average capacity of 100 tons of green pellets per hour. The balling drums are equipped with rotating scrapers and water-spraying systems. The scrapers are installed in order to restrict the growth of the race to a certain thickness. The spraying system is used to adjust the desired value of the moisture-content of the rewetted ground ore, the pellets and the race. The desired value is the value by which the balling- process is stable, good pellets are formed and surge occurs within certain limits. In October 1980 the construction of one of the balling drums has been modified. The rotating scraper was removed and the inner wall of the drum was supplied with a rubber-lining. In 1982 a second balling drum has been rubber- lined. At the same time the Tyler vibrating screen of this balling circuit has been replaced by a roller(bed)screen. By the end of 1983 all 7 balling circuits will be equipped with rubber-lined drums in combination with roller(bed)screens. The combination of these two modifications will improve the quality and the screen analysis of the green pellets, moreover resulting in savings on energy- and maintenance costs. This paper describes the influence of a rubber- lining on the balling process and the green pellet quality by carrying out in-plant testruns in November/December 1980. The testrun results have been compared with the results of a not modified balling drum.

Jan 1, 1983

By C. A. Rawlins

INTRODUCTION Radcont is a program designed by the author of this paper for the industry to use as an instrument for radiation contamination evaluation and ventilation planning system. Radiation in mines are associated with the mining of gold and gold bearing minerals, as uranium and thorium is incorporated in the mining of these minerals. Radiation contamination in South African mines is not a new concept as it was investigated by the Chamber of Mines in the early 1960&apos;s and found not to be hazardous at the time. Since some of our mines export scrap metal to customers abroad, it came to light (1991) that some of the scrap metal was radioactive. The authority that oversees the nuclear aspects in South Africa is the Council for Nuclear Safety (CNS). They investigated these matters and found that the mines needed further information regarding radioactive material and the handling of these contaminated materials. As the various mines were licensed (with various conditions incorporated) thereafter, the mines had to do their own investigations as to what extent their properties (Surface and underground) were radioactively contaminated. Some mines were found to be highly contaminated over the years of operation and controlling conditions were installed and measures installed to reduce the contamination levels. One of the conditions when issuing a licence by the Council for Nuclear Safety (CNS), is that a screening survey be carried out to determine the radiation exposure levels and corrective action to be taken if necessary. These surveys must be done by a person trained in the required procedures for such a survey. The person must also measure the risk correctly and assess the results properly. In such a survey, the internal and external exposure levels must be determined to assess the total exposure of persons working in those conditions and take appropriate action if necessary. When doing such a survey, hundreds and more likely, thou- sands of data points are recorded. In order to assess the data recorded, various integrated and difficult calculations need to be made, and takes up enormous amounts of time. (This excludes the interpretation of the results ) The following explanation of the program shows the different parts of such a survey assessment calculations to be done. The paper details the program layout and the different sub- sections within the primary program. It must be stated that the program, as with any other program, is as accurate as the data inserted into the data base. The program and details thereof are given under the following headings: 1. TOTAL EFFECTIVE DOSAGE WITH REGARDS TO: • GME required gravimetric results obtained (mg/m3) • Thick layer or total contamination measured (Bq/m2) • Dry condition surveys with dust loads taken as a Standard l0mg/m3 • Wet conditions survey with dust loads taken as l mg/m3 • Airborne long lived alpha and beta activities as determined by analysis in Bg/m3 • LTD (Thermoluminescent Dosimeter). Results as obtained from the SABS (South African Buro of Standards) are recorded in this section for each month of the year for each individual worker. An average dose is then determined at the end of the year. • Bucket measurements as recorded. • Smear samples (Loose contamination). As determined by Electra or by analysis • Occupational factors for Metallurgical and Engineering occupations in and around the Metallurgical facilities of your mine. • All underground dosage determination and calculations. (Radon and Thoron) 2. INFORMATION REQUIRED WHEN PROGRAM IS INITIALISED: As the program is started, it opens up on the contents page. Here there are various options to choose from, but one is cautioned as a beginner in operating the program, not to perform any tasks before carefully reading these instructions. Firstly, one must go to the &apos;Information required" pushbutton. Press this button. The information required page is shown where the cursor can be moved to the block where one can enter the specific mines name. To enter a mines name, put the cursor in the block provided and just insert the mines name with the normal keyboard keys and press the enter button on the computer keyboard. To enter the other information required such as Alpha and Beta instrument efficiency, ALI (Annual limit of intake) and probe area, one can either press the &apos;Data required" button for a dialog box information or enter it manually by just putting the cursor in the block provided and entering as did above. In order to insert all the required information for the pro- gram to calculate the information required, one must proceed further by entering the area names surveyed in the spaces provided. There are 20 spaces to enter 20 different areas surveyed. One must further also provide the amount of days worked in each area (i.8. 250) in the block provided. The de- fault is 250 days. There are also standard information given in the information data page such as breathing rate (1,2 m31h), 8 hours worked per day, 5 days per week and 50 weeks per

Jan 1, 1997

By C. J. Pritchard

As productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity, a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The tailgate development continuous miner section has been since transformed from a low productivity part-time function to a high productivity development/retreat panel and is available for long term mine development duties also.

Jan 1, 1989

By H. L. Lovell

The growing production of fly ash with the many attendant problems of economics, disposal and potential uses suggests an urgent need to consider those properties which are basic in its beneficiation. Fly ash is extremely variable and heterogeneous in all respects except its fine size. Because of its production in huge quantities, it becomes significant as a potential raw material. Detailed data are presented describing particle size and shape, density distribution and magnetic characteristics. The major components include combustible residuals, magnetite and silicates. These data are discussed in terms of beneficiation processes and uses, The results of air classification to produce a uniformly fine-sized low combustible product are encouraging. It is proposed that major increases in the future use of fly ash, must involve some form of beneficiation. Both the coal producing industries and the consuming utilities would benefit from increased utilization.

Jan 1, 1964

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By W. B. Weston

To mining people who have experienced the tremendous expansion of existing operations and the development of new properties over the last several years we do not have to point out the difficulties in hiring skilled equipment operators. To those of you who have opened operations in some of the more remote places in the world this is not just a difficulty. It is an impossibility. Your only recourse has been to try and train whatever manpower has been available. Depending upon your success in training, the next problem has been to keep them. On todays modern equipment, the skill of the operator remains as the greatest single variable affecting the performance of the machine. On a blast hole drill, for example, a skilled operator will get good production footage, acceptable bit life and minimal machine downtime The unskilled operator will not only fail to get the acceptable production footage but all too frequently this failure is coupled with low bit life, high repair costs and excessive machine downtime. Even between experienced operators, on identical machines, in the same kind of material we find significant variations in performance. It is, therefore, the skill of the operator, not just his experience, which makes the difference. The problem, as presented to us by our customers, has been to find a way for the unskilled man, with minimal training, to match the performance of the most skilled and experienced operator. The obvious answer is automation.

Jan 1, 1970

By Jaime Adasme, Héctor González, Benjamín Celada

"INTRODUCTION Santiago de Chile is a 7 million inhabitant city which has a 103 Km long subway network operated since 1975 by Metro S.A. This network is used on a daily basis by 2.3 million people. In 2012 Metro S.A. started the biggest enlargement of the network in its history, through the design and construction of the new Line 3 (21.7 Km) and Line 6 (16.5 Km). The detailed engineering contract for civil underground works of Line 6 (L6) was awarded to the Consortium integrated by ZAÑARTU Ingenieros Consultores and GEOCONTROL S.A., in which Geocontrol was in charge of the design of 11 stations and 14.5 Km of tunnel. L6 crosses L3 in Ñuble and Ñuñoa Station, L2 at Franklin Station and ends, intersecting L1, at Los Leones Station as shown in Figure 1. LOS LEONES STATION DESIGN Location and Characteristics Los Leones Station is placed at the North end of the L6, next to the same named station of the L1 and it has four construction units, as is shown in Figure 2: I. Access Shaft (49 m x 47 m). II. Access Gallery (34 m long). III. Station Tunnel (120 m long). IV. Connection Gallery with L1 (104 m long). A singular feature of Los Leones is that the western section of the station tunnel, built from the access gallery, is located below an underground parking lot which is located in Providencia Avenue, as shown in Figure 3. It is important to highlight that the distance between the vault of Los Leones Station Tunnel and the foundations of the underground parking lot is only 6 m."

Jan 1, 2016

By Guy Reed, Russell Frith

In situ or pre-mining horizontal stresses are arguably the least well understood of the principal inputs into underground coal mining geotechnical engineering design, whether analytical, empirical, or numerical. This is a direct result of both the cost and difficulty of obtaining meaningful stress measurements, the various limitations of the measurement method in terms of sourcing strata types that approximate the assumed conditions of the post-measurement mathematics to convert measured strains into stresses, and a common practice by some geotechnical professionals to preferentially utilise generic values rather than interrogate the available measurement data for cause and effect relationships between horizontal stress magnitudes, directions and a range of associated controls. That numerical modelling simulations attempt to mimic reality but often rely on simplified generic horizontal stress input assumptions is a particular cause for further consideratio The paper attempts to further explore the nature of in situ horizontal stresses using a range of stress measurement results from the Australian coal sector supplemented by several international studies addressing the same basic issue, the result being a number of credible and highly relevant “cause and effect" inter-relationships between the three principal in situ stresses in addition to the influence of rock properties (e. Young's Modulus and Poisson's Ratio), cover depth and the larger-scale structural geological environment. In particular, the paper demonstrates that despite being commonly overlooked as a primary rock/coal material property, Poisson's Ratio and the associated K Effect are intrinsic to understanding 3D in situ stress measurement results and therefore, predicting in situ stress magni- tudes more generally for geotechnical analyses purposes. As a fundamental question, the paper addresses whether it is necessary and of engineering value to characterise in situ horizontal stresses: according to distinct "domains," in the same way that more easily identifiable geotechnical properties such as rock mass ratings, coal seam thickness, ply splits, and cover depth are often treated.

Jun 25, 2024

By John Drew Ridge

Tables showing world trade in metallic mineral raw materials during the years 1953 through 1957 have been prepared for the following twenty-one commodities: alumina, aluminum, bauxite, chromite, copper concentrates, partly refined and fully refined copper metal, iron ore, pig iron, iron and steel (simple shapes), lead concentrates, lead metal, manganese ore, mercury metal, nickel ore, concentrates, and matte, nickel metal, raw pyrites, sintered pyrites, tin concentrates, tin metal, zinc concentrates, and zinc metal. In each instance, the amounts given by the importing country were used except when statistics from the importing nation were lacking, incomplete, or misleading. To show the considerable divergence between importing and exporting country totals for the same years, the complete mercury table is given and, in parallel columns, shows the comparable tonnages of importers and exporters. Tables for the other twenty commodities are presented in summary form. The data of the concentrate tables are used with those of the corresponding metals as a basis for a discussion of trade in concentrates versus trade in metals. The data of all twenty-one tables provide the basis for testing the thirteen rules governing international trade in metal raw materials which I first published in Mining Engineering for July 1955. Because the 1953 through 1957 data are far more complete and considerably more extensive than those on which the 1955 rules were based, it was found possible to deduce five additional rules and to modify three of the original thirteen appreciably. The full text of the eighteen rules is given.

Jan 1, 1960

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018

By C. E. Chapin

The Hansen orebody is a large (1 2 million kg U3O8, 0.08% U3O8 average grade) sandstone-type uranium deposit in the Eocene Echo Park Formation of central Colorado. The deposit occurs in carbonaceous braided-stream sandstones that are part of a wet-alluvial-fan complex that prograded eastward across a narrow strike-slip basin. The Echo Park basin is one of a series of basins that formed along the east side of the Colorado Plateau as it was translated northward during the Eocene culmination of the Laramide orogeny. The valleys of east- and southeast- flowing perennial streams, whose courses were transected by the subsiding Echo Park basin, were filled with permeable volcanic and sedimentary rocks during construction of the Oligocene Thirtynine Mile volcanic field. These paleovalleys funneled large volumes of uranium-bearing ground waters through the braided-stream facies of the wet alluvial fan. Uplift of a basement horst downfan from the Hansen orebody reduced transmissivity and helped maintain a reducing environment in the Hansen area; this later became an important factor in preservation of the Hansen orebody. The horst also deflected uranium- bearing ground waters upward into the Oligocene Tallahassee Creek Conglomerate where they formed the Picnic Tree orebody (1.1 million kg U3O8, 0.09% U3O8 average grade) in an altered ash-fall tuff that is essentially barren above the Hansen orebody. Several potential source rocks for uranium are present and range in age from Proterozoic quartz monzonites of Silver Plume age to lower and upper Oligocene ash-flow and ash-fall tuffs. Uranium may have been contributed to the Hansen orebody several times from different sources. Uranium and thorium analyses of ash-flow tuffs indicate that ample uranium was released during cooling and ground-water leaching to form several Hansen orebodies. The host sandstones are conspicuously altered, and their initial high permeability has been greatly reduced by precipitation of intergranular cements, especially clays and opal C-T. The alteration and cementation mineral assemblages and the chemical composition of stagnant ground waters recovered from pump tests indicate that uranium deposition occurred under alkaline, reducing conditions preceded and/or accompanied by bacterial production of framboidal pyrite.

Jan 1, 2013