Search Documents

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By T. A. Rundle, K. Kim, W. M. McCabe, E. C. Gregory

Overcoring tests were conducted at the Near-Surface Test Facility(NSTF) to assess the suitability of five techniques (U.S. Bureau of Mines borehole deformation gauge (BDG), Commonwealth Scientific and Industrial Research Organization (CSIRO) hollow inclusion stress cell, Luleå triaxial gauge (LuH gauge), and Council for Scientific and Industrial Research (CSIR) doorstopper) for in situ stress determination in a closely jointed basalt. This effort is in support of the Basalt Waste Isolation Project, which is studying the feasibility of locating a nuclear waste repository in the basalts of the Hanford Site in southeastern Washington. This paper presents the results from the overcoring study that formed the basis for selection of two techniques to be used during the further exploration of the basalt formations at depth.

Jan 1, 1983

By L. Lipsett

"Human rights can contribute to sustainability in the mining sector, both in theory and in practice. Both human rights and sustainability share a common concern to improve economic prosperity, environmental health and social equity by avoiding negative impacts and conflict, as well as by engaging with and empowering affected communities. Globally, there is an emerging consensus that companies have a responsibility to respect international human rights standards. Respecting human rights means that mining companies are responsible to ""do no harm"" to the people and communities affected by their operations. After a discussion of the Protect, Respect and Remedy framework for business and human rights, this paper illustrates some examples of how international standards for human rights and sustainability interacted in a recent assessment of Goldcorp's Marlin Mine in the Western Highlands of Guatemala. The final section explores how human rights should be integrated into broader policies and procedures for corporate sustainability. This includes integrating human rights into ESIA processes, legal compliance, corporate governance and grievance mechanisms. Pressures on mining companies to respect human rights will not disappear; therefore, a proactive and integrated approach to human rights is a fundamental component of a broader strategy for sustainability"

Jan 1, 2011

By J. Reed

The RockWorks EarthApps represent a free collection of 74 geology-related programs that read data from a built-in datasheet and create diagrams within Google Earth. EarthApps also includes programs that extract data from Google Earth. The programs that create diagrams include: point mapping (e.g. borehole locations), proportionally scaled icons (e.g. geochemistry), and strike & dip symbols. Line mapping utilities include; polylines, parabolas and pipelines. Polygon mapping programs include; thematic mapping (e.g. geology), mining claims, and public land survey sections. Image overlay capabilities include; draping (e.g. geologic maps) and time-based animations. Vertical image display capabilities are centered on either midpoints (e.g. drill-hole logs) or stretched between endpoints (e.g. cross-sections). The Flyover programs create virtual tours for site presentations. The cell-mapping includes a variety of algorithms (e.g. geochemical and geophysical contouring). Survey programs convert and export survey data to Google Earth as points and polygons. Programs that extract data from Google Earth include; points, lineations, polylines, and polygons. The RockWorks/EarthApps collection is developed by RockWare Incorporated based in Golden, Colorado.

Feb 27, 2013

By R. E. Brewer

Pilot scale flotation tests were conducted with a 1-ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pct of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated using the column. The tailings were first water leached at approximately 600 C, and the water-leached tailings, which contained approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH and sodium sulfide addition on gold flotation recovery and redox potentials were examined. maximum gold recovery, 36 pct, was achieved at pH 8.5 with a sodium sulfide addition of 0.18 lb/st.

Jan 1, 1989

By Joseph Goessling, Mark Kroncke, James Parkes

The I-35 Capital Expressway (CapEx) Central Drainage Tunnels will serve as a stormwater collection system for the forthcoming I-35 Capital Express Central reconstruction project through downtown Austin, Texas. The schematic level concept design included three tunnels, 10 to 14 ft ID, totaling 26,000 LF. Constructability reviews during design development indicated issues with the concept design including phasing of construction, conicts with future retaining walls, staging area concerns, and signicant mixed face tunneling. The design was updated to mitigate these risks. The revised design includes two tunnels, both 22-ft ID and totaling 33,000 LF, that will be mined almost entirely in rock.

Jun 23, 2024

By D. E. Healy

In 1989 an Autogenous Grinding Task Force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding at the National Steel Pellet Plant located in Keewatin, Minnesota. Pilot plant test work performed by the Hanna Research Center (HRC) indicated that fully autogenous grinding with pebble extraction and crushing could feasibly be incorporated into the existing circuits. In 1990, one of the existing ten grinding mills was converted for an in-plant test incorporating pebble crushing. The full scale test work conducted in 1990 and 1991 verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit utilizing pebble crushing being greater than throughput of the existing SAG mill circuits.

Jan 1, 1992

By T. M. Sukel

Engelhard Corporation is one of the leading producers of kaolin based products in the world, having acquired the assets of Freeport Kaolin company in 1985. Much of the production technology used in the kaolin industry was pioneered by Engelhard and Freeport, including Ultraflotation for improving product brightness, delamination to produce kaolin platelet products, calcination to produce ANSILEX® high opacity titanium dioxide pigment extender and pipeline slurry operations to economically transport kaolin from the mine to beneficiation facilities. Engelhard traces its roots back to 1870 when the Edgar family discovered kaolin behind their property in Bonhamtown, New Jersey. Today the company produces the broadest line of premium coating pigments with extensive sales throughout the world. The international scope of the company's business has led Engelhard to evaluate kaolin deposits throughout the world as possible grass roots production sites. Most kaolin products are used in the paper industry -- the largest volume end-user 80% of the total market -- as filler and coating pigments. Lower volume specialized applications include fillers and reinforcements for plastics and TiO2 extender pigments for paints and coatings.

Jan 1, 1987

By F. Schreiter

The Ore Mountains in Germany have a history of more than 850 years of underground mining activity. This has created a situation where thousands of old mine shafts and adits are due for rehabilitation. While no long-term stable rehabilitation was executed in previous centuries, those abandoned mine sites which date back to the uranium mining boom from 1945 to 1962 were rehabilitated immediately after mine closure according to state-of-the art technology. Over the years, however, it has become obvious that most of these sites are not long-term stable and thus it has become necessary to rehabilitate them a second time. Technical University Bergakademie Freiberg is carrying out a research project on the optimization of this process. 70 mine site rehabilitation projects, the technology and the materials used have been assessed. A technical guideline for future rehabilitation projects, based on the outcomes of this assessment, is under development with the goal to make it easier, faster and more economical to select and apply suitable designs and construction materials for dams, plugs and other rehabilitation structures in former uranium mines.

Feb 27, 2013

By Rebecca S. Stanevich

BACKGROUND Diesel exhaust is an animal carcinogen, although evidence of the carcinogenicity in humans is "limited". (World Health Org. , 1989) Of the eight cohort studies in the 19808, five found an increased risk for lung cancer among workers who may have been exposed to diesel exhaust (RR from 1.3-1.5, SMR from 101-132). (Howe, et al., 1983) Only two studies accounted for smoking indirectly. Of the ten case-control studies in the 1980's, eight reported increased risk of lung cancer among those populations purportedly exposed to diesel exhaust. (Benhamou, et al. , 1988) All but one of these adjusted for smoking and other occupational exposures. The odds ratios ranged from 1.2 to 2.1. In two of these studies, miners experienced a two to three fold risk. (Benhamou, et al., 1988) Bladder cancer has also been linked to diesel exhaust in cohort and case-control studies. Excesses of approximately 50% were observed among truck drivers in studies by NCI. (Hoar, et al., 1985) In the National Bladder Cancer Study, risks for truck drivers rose with duration of employment. A study by NIOSH in Ohio also found an excess of bladder cancer among truck drivers, particularly among those with 20 or more years of employment. (Steenland, et al, 1987) Despite the large number of studies in which the relation between diesel exhaust exposure and lung cancer has been examined, exposure to diesel exhaust has been quantitatively estimated only in the studies of railroad workers and truck drivers. (Woskie, et al., 1988) The excess lung cancer risk experienced by workers in these two occupational groups was modest, ranging from 40 to 90% for those with long-term employment. However, diesel exhaust exposure among railroad workers and truck drivers is lower than that seen among miners. Several markers of diesel exhaust have been utilized in these studies. Diesel exhaust is a complex mixture of particulates, vapors and gases. One group of these gases, the nitrogen oxides, react with polynuclear aromatic hydrocarbons, forming mutagenic and possible carcinogenic nitrated derivatives. (World Health Organization, 1989) For this reason, and because it is easy to measure and analyze, NO, was frequently used as a marker of diesel exhaust exposure. As part of the Garshick (Garshick, et al., 1988) study of railroad workers, Woskie measured NO, exposures of 477 railroad workers. (Woskie, et al., 1988) Geometric mean exposures of 13 job groups ranged from 12 to 80 ppb. In a New Mexico potash mine, (Attfield, et al. , 1982) exposures of from 100 to 3300 ppb nitrogen dioxide

Jan 1, 1992

By T. P. Meloy

In the last decade increased and prolonged interest has been displayed in the use: of tunneling or rapid excavation to solve many of the urban and industrial problems confronting our society. There has been talk and action on the interurban rapid transit systems for major cities, and even preliminary designs for a Boston to Washington interurban transit system. Much of this interest stems from the search to the solution of our increasingly complex urban problems, where the surface area must be given over more and more to the inhabitants, and the subsurface for transit, utility and other services. While tunneling is not a panacea to urban ills it holds a real solution to many existing problems. There is also, among the tunneling experts, a growing confidence that technical problems of rapid tunneling can be solved. To solve these problems, R & D money must be invested. If it is to be money invested either by private industry or governments, there must be significant returns on the investment to justify the research and development need to bring about the breakthrough that will make tunneling a major contribution to the solution of urban problems. To make these economic studies more extensive and more accurate tunneling demand figures were needed. To this end, the Organization of Economic Cooperation & Development - OCED - included in its Conference on Tunneling a section on tunneling demand. As a result of the conference the organization for Economic Cooperation and Development issued a report entitled "The Advisory Conference on Tunneling - Report on Tunneling Demand 1960-1980. " This report was presented at the OCED Conference on Rapid Excavation, held at Washington, D.C. To obtain the data in the Report, questionnaires were sent to the OCED countries and 18 replies were received from Australia, Austria, Belgium, Canada, Denmark, France, Germany, Ireland, Italy, Japan, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom, and the United States. While it is true, that data were missing, that sometimes the definitions were confused, and that several countries provided no cost estimates at all, in general, this report contains the most comprehensive gathering of data that ever existed in the field. All data in the OECD report is expressed in terms of meters or cubic meters, and costs are in U.S. dollars.

Jan 1, 1970

By W. A. Van Dyk

Hydrophobic particles with diameters between 1 and 3 mm are poorly recovered by conventional flotation techniques. A novel reverse flotation technique is described whereby coarse particles with surfaces rendered highly hydrophobic, repel the bubble films in a froth and thus drop through the froth under gravity, to be recovered as a sink product. Conversely, gangue or hydrophilic particles are supported by the bubble films in the froth and are therefore recovered as a floating product. Tracer tests were conducted in the cell in order to study the dynamic behaviour of solid particles in the froth. The effects of hydrophobicity, density, particle size and particle shape were investigated experimentally. The higher the hydrophobicity of the particles, the lower the recovery of particles as a floating product, while the recovery of particles as a sink product increases with an increase in particle density. Furthermore, a decrease in particle size results in an increase recovery of hydrophobic particles as a floating product. When treating particles of the same mass-to-surface-area ratio in the froth, flat particles would be recovered as a floating product in preference to cubic, disc-shaped, cylindrical and spherical particles, in that order.

Jan 1, 1995

By Muhammad Azeem Raza, Samuel Frimpong

Underground mining environments are inherently hazardous and can lead to emergencies where effective rescue and self-escape become critical. Missouri University of Science and Technology is pioneering new technologies for effective self-escape. The rescuers and miners need to be trained in these new technologically driven environments. Previous research in fields like aviation, medical surgery, and oil and gas drilling has demonstrated the effectiveness of virtual simulation training, but the mining sector has yet to fully adopt advanced tools such as eye-tracking and immersive training modules. This research proposes a comprehensive training infrastructure incorporating these technologies to enhance situational awareness and decision-making during emergencies. The novelty lies in the application of advanced miner escape and communication technologies, specifically designed to monitor and enhance cognitive responses in high-stress situations. By leveraging these technologies, the proposed training infrastructure aims to prepare the next generation of underground miners and operators, by equipping them with the necessary skills to manage emergencies effectively.

Feb 1, 2025

By P. Richardson, B. Sceresini

The carbon-in-pulp and the carbon-in leach process for the recovery of gold and silver from cyanide leaching of ores is now widespread in the precious metals mining industry. However the presence of various base metals can have a detrimental effect on the efficiency and the economics of the process due to high cyani,:••? consumption and a reduction in leaching and adsorption rates resulting in poor recovery of the precious metals. Furthermore the presence of fast leaching and adsorbing metals such as copper can significantly reduce carbon loading capacity for the precious metais thereby necessitating a higher carbon inventory, more frequent stripping and poor bullion quality resulting in higher production costs. This paper describes the development and application of a process for the recovery of copper and and the recovery and re-use of the associated cyanide from the leach circuit at the Mt. Gibson Gold Project in the Murchison Goldfield in Western Australia. The process provides a means to counter-act the detrimental effects of the copper which occurs in the ore as various oxide and sulphide minerals including an extremely fine chalcopyrite powder. It has the added benefit of recovering the base metals in this instance copper, in a saleable form. The process is subject to a patent application by Reynolds Australia Metals, Forsayth N.L. and the author.

Jan 1, 1991

By H. F. Ghezzi

The indirect method of drying coal fines is applied to filter cakes which ordinarily contain 22 to 30% moisture and are not readily transportable. The "Thermal Dryer", which operates on the mass transfer principle, has found wide use in coal preparation plants. The thermal dryer is penalized in operation by the necessity of adding coarse coal to the wet fines before entering the dryer body in order to produce a permeable bed, and thus enable hot gases to uniformly contact the wet mass. The ratio of coarse coal to fines varies from 2:1 to as much as 4:1, depending on the average particle size, moisture, and ash content of the fines.

Jan 1, 1985

By A. Fuerst

The recent seismic events have shown that earthquakes have an immense destructive power. Chile was hit in February 2010 with a seismic intensity of 8.8 on the Richter scale, and had loss of about 700 killed persons, while Haiti was hit in January 2010 with 7.0 killing about 220?000 people. The event in Haiti showed that the seismic events can lead to a disaster if no preventive measures are taken. On the other side, the seismic event in Chile has hit a well-prepared country with moderate consequences. The earthquake with 6.6 Richter in Japan in March 2011, have further shown how severe the consequences can be if critical equipment is involved. Fortunately, the equipment in a mine has not the potential hazard as a nuclear power plant. Anyway, we are diligent and it is obvious that the seismic risk may lead to a real disaster even if the probability is small. The GMD is an important component in the grinding circuit of a mine. This paper maps out earthquake-prone areas including expected earthquake magnitude calculated according to relevant standards, focusing mainly on the building code IBC 2009. An overview is provided on how this standard is applied to mining equipment to minimize damage and aid large mills in operation to successfully withstand seismic effects. The differences in stresses and forces on the GMD and foundation are shown based on a turning and stopped mill simulation during an earthquake. The results demonstrate the need to maintain active and operating earthquake detection systems. Aside from detecting an earthquake?s magnitude, the sensor information can also be used to reduce the harmful effects that an earthquake has on mining equipment. As follows the earthquake requirements are defined. The last part of this paper explains how to fullfill these requirements.

Jan 1, 2012

By T. W. Camm

"Search Amazon.com using the keyword “leadership,” and you are rewarded with a list of over 144,000 titles. There is no shortage of books and articles, many of them well written, with excellent ideas. So why is there still a constant cry for effective leadership in organizations? Often, the person in charge has personal blinders that prevent them from seeing or understanding how to implement the newest leadership idea or method. Either deliberately or subliminally, there is a disconnect from learning about leadership, and actually modelling and implementing what has been learned. Some current research in leadership theory can provide insight and tools to address this issue. INTRODUCTION Let’s start with a discussion of terms. Pseudo is defined by Webster (2015) as “Being apparently rather actually as stated.” Synonyms include affected, assumed, contrived, fake, false, phony, pretended, and artificial. Antonyms for pseudo provide additional clarity, especially when we consider terms normally associated with effective leadership: genuine, natural, unaffected, unforced. A similar type from my world of academia is a pseudointellectual, “A person exhibiting intellectual pretentions that have no basis in sound scholarship” (Dictionary.com, 2015). This is a person pretending to have an interest in intellectual activities for status; a fraudulent intellectuality. The thought of applying the term pseudo to leadership first occurred to me while reading Power and Innocence by Rollo May (1972). In discussing the dynamics of power, and how the innocent are often victims of the exercise of power, especially the more aggressive and destructive types of power, he saw two types of innocence. The first he called authentic innocence, which he described as a childlike clarity that carried into adulthood. The second type he called pseudoinnocence, a type of naïveté that makes a virtue of powerlessness, weakness, and helplessness; being more childish than childlike (p. 48-50). Just as there is the potential for pseudoinnocence and pseudointellectuals, it is also possible to experience pseudo leadership. (I hope the gentle reader is not troubled by my decision to use pseudo leadership as two separate words, in contrast to the use of compound words for pseudoinnocence and pseudointellectual cited above. Since there is no official definition of pseudo leadership, I have exercised my author’s prerogative to treat it as two words, both because I think in this particular application this makes the most sense, and also I think it is easier to read). As we will see, there are numerous theories applied to leadership. What is so troubling to many of us in organizations, there are a myriad of “leaders” in companies espousing pet theories, but very few instances where the actions of these individuals match their words. This is a particularly important problem when we look at the effect this has on the day to day operations of a mine, and where effective leadership (or its absence) can have a profound impact on both productivity and safety."

Jan 1, 2016

By J. I. Adetunji

Mining activities usually affect the soil, subsurface layers, water resources, the atmosphere and in general the lives of the people. The effects can be mechanical, biological, ecological and economical in nature and these effects can be characterized by their intensity, frequency, duration and scale. In Oyo State, Southwestern Nigeria efforts are being made to employ a sustainable method in the exploration and exploitation of abundant industrial minerals present in the state. The minerals exploited include talc, clay, marble, sillimanite, tantalite, niobium, beryl, tourmaline aquamarine, rock aggregates, etc. Results of this sustainable approach show that the environmental impacts of surface and underground mining of industrial minerals are not spread far beyond the mines site acreage. More lands are being reclaimed, the amount of dust released into the air has been minimized, the quality of sewage waters produced during operations are minimized, top soils removed during subsurface mining are preserved, the tonnages of minerals exploited are being monitored and controlled. All these point to a positive development in practicing sustainable methods in mineral exploitation to meet the developmental needs of the Oyo State at present and to conserve for the future.

Jan 1, 2003

By M. Guzman, S. B. Thais, M. F. Obispo, M. R. Arribasplata

The impact generated by old abandoned mines in Peru have produced mining environmental liabilities, which can generate an impact on the environment. In the search for long-term sustainable solutions, Phytoremediation is presented as an interesting alternative, since it allows the use of Peruvian native plant species for the accumulation of heavy metals. In this paper, we present the results of native high Andean species: Stipa Ichu and Cortaderia Nitida. The final metal concentration in the aerial parts and in the roots of each plant show that Stipa Ichu is more efficient to recover Fe, reaching almost 278 times its initial value. In the same way, this plant is efficient to remove Zn, Cu and Cd, reaching maximum values of 64, 39 and 12 times its initial concentration respectively. Cortaderia Nitida turned out to be more efficient to recover Fe, Zn, Cu and Cr, with highest recovery of 250, 117, 39 and 13 times its initial value respectively. Finally, based on translocation factor, Stipa Ichu has better capacities of hyperaccumulation of Fe, Cu, Zn, Pb and Cr. Cortaderia Nitida only shows hyperaccumulation of Cr.

Mar 2, 2022

By Gary B. Hemphill

The 345 km long Taiwan High Speed Rail Project will connect the island’s two most populated cities, Taipei and Kaohsiung. Kaohsiung is the world’s third busiest port. The 23 km of alignment on Contract C230 requires the construction of 5,879 m of shallow mined tunnels ranging from 137 m to 1,285 m in length. All nine of these tunnels are mined using NATM methodology. Two of the tunnels, T01 and T08 are in the Toukoshan Formation. This paper will discuss the mining methods, ground support design, and the instrumentation installed to monitor and verify its effectiveness in the two aforementioned tunnels.

Jan 1, 2003