Search Documents

By B. Catalano, D. Ifrim

The Annacis Island Outfall Project includes two TBM bored tunnels with face pressures above 3.5 bar, with an internal diameter of 4.2 metres. This paper discusses the innovative approach to TBM tunnelling and TBM design at the Annacis Outfall Project. The TBM custom design includes a 3.6 m OD core machine manufactured by Herrenknecht and a 5.0 m add-on by the Contractor (Bessac), acting as an extension kit, with optimized gantry design to accommodate for short tunnel drives and quicker launches. This novel design approach produced safety improvement, cost and schedule savings while streamlining logistics of TBM retrieval.

Dec 1, 2022

By J. Humphrey

Introduction The weight of a Mining Truck can be affected by field modifications, the selection of items like tires, rims or even the conditions in which it operates. Truck performance and the compliance with a number of ISO standards, e.g. braking, steering and ROPS are dependent on truck weight. It is critical that truck owners understand the impact of changes in weight1. What makes this even more difficult for owners to evaluate is that there is no standard terminology or definitions for Mining Truck weights. This paper discusses and defines weight terminology, how it applies to performance and standards and the impact on the application of Mining Trucks.

Jan 1, 2007

By Lawrence Tsang, Conrad Ng, Tim Leung, Peter Poon

"The Mined Tunnel is part of the Central-Wan Chai Bypass and Island Eastern Corridor Link (CWB), which is a strategic road along the northshore of Hong Kong Island targeted to alleviate the heavy traffic congestion. The objective of this paper is to review the performance of construction of a 160m long Mined Tunnel with a trinocular cross-section area of 460m3 and a combined span of about 50m underneath the southern approach ramp of the existing Cross Harbour Tunnel (CHT) by sequential excavation method (SEM) in hard rock. Mechanical excavation of tunnel by adopting the New Austrian Tunnelling Method (NATM), together with the application of NGI Q-system allows observational approach and optimization of temporary rock support design. Furthermore, the good performance of optimized rock support and the stability of CHT are confirmed through instrumentation monitoring review. This paper also discusses the selection of different tunnel plant and equipment to achieve the planned rates of tunnelling by mechanical excavation in competent granitic rock. INTRODUCTION The works of the CWB mainly comprise construction of 4.5km dual three-lane trunk road, of which a 3.7km section is a tunnel connecting Rumsey Street Flyover in Central to Island Eastern Corridor at North Point (see Figure 1). The Mined Tunnel runs from the ex-Public Cargo Working Area (ex-PCWA), underneath the existing CHT, and through the Causeway Bay Typhoon Shelter. The Mined Tunnel passes at an oblique angle beneath the southern portal of CHT over a length of some 50m. CHT is the primary sensitive receiver of this project and is utilized with a daily throughput of about 120,000 vehicles that far exceeds the design capacity of 78,000 vehicles per day. Hence it is necessary to choose the most appropriate tunnelling method to preserve the structural integrity of the CHT. Other sensitive receivers in the vicinity include structures to the north of the Mined Tunnel, the Royal Hong Kong Yacht Club (RHKYC); and to the south of the Mined Tunnel, the Police Officers’ Club (POC)."

Jan 1, 2016

By Ken Goering, Steve Kral, William Gleason

"Once every four years, the global mining industry gathers in Las Vegas, NV for MINExpo International. According to the show’s organizer, The National Mining Association (NMA), about 44,000 people attended the three-day show from Sept. 26-29. It was a show that featured the latest and greatest in equipment and technology. It also served as the backdrop for a snapshot of the state of the industry and while the picture of a global industry is never completely clear at any one time, one thing that is evident is technology has become a major force in the way mining is done.Had it not been for the awe-inspiring “iron” that was on the show floor in the form of haul trucks and shovels weighing hundreds of tons, one could be forgiven for thinking that they were at the Consumer Electronics Show. From training simulators designed to give a realistic experience of operating mining equipment to virtual reality technology that can take the user into the depths of an underground mine or the middle of a mapped ore deposit, an overriding theme of MINExpo 2016 was that the mining industry is connected like never before.In the north hall of the Las Vegas Convention Center was the GE Mining booth that was designed to showcase its efforts to help create a mine that will be connected from the front office to the face of the underground wall or bottom of the openpit. GE Mining called its booth a digital mine, and it included a suite of technologies that can improve performance, reliability, safety and operations. GE Mining said it views each mine as a mini-city, requiring power, water and transportation. Intelligent, real-time monitoring across the mine allows operators to make data-driven decisions that improve equipment reliability and optimize mine operations for substantial savings. And GE Mining was just one of many exhibitors showing off software that allows various types of equipment to communicate. Its booth sat in the shadow of the Komatsu booth with its new 360-t (400-st) 980E-4 haul truck that included GE’s 360-t (400-st) electric wheel motor. This is just one example of how technology is connecting machines, operations and people around the world and how mining is moving forward."

Dec 1, 2016

By G. Wang, L. R. Moore, Y. Xiong, A. Gorken

"Feldspar may represent 60% of the earth’s crust, but the mineral does not exist in a pure state. It is generally associated with quartz, iron containing minerals such as mica, and titanium containing minerals such as rutile. Feldspar itself can even exist in different lattices from those containing sodium to various divalent ions. As such, its beneficiation has become a process that is quite complicated, when compared to the beneficiation of other minerals. It is this complexity that has made feldspar beneficiation dependent on tailor made reagents to successfully yield the industry specified feldspar products. This paper reviews the mineralogical variations found from two feldspar mines and the development of collectors to specifically target a Fe+Ti concentration of < 0.05%, while maintaining a feldspar recovery greater than 90%.INTRODUCTION Feldspar is a class of aluminum silicates that represents the most abundant mineral on earth (Vidyadhar, 2002). This class of mineral can further be defined by the types or concentrations of cations present in the crystal lattice, MAlSi3O8 (M = K, orthoclase and microcline; M = Na, Albite; M = Ca, Anorthite) (Heyes, 2012). Feldspar is most commonly mined and processed for either the alumina used in glass making or for the alkalis used in ceramics. The alumina is known to improve product hardness, durability, and resistance to chemical corrosion. The alkalis act as flux, which means they not only lower the melting temperature of the mineral mixture, but also assist in connecting the other components present in ceramics. It was stated in 2009 that the world production of feldspar was in excess of 18.3 million tons produced, with the majority coming from China, Italy, and Turkey. Raw feldspar is typically found with quartz, iron containing minerals such as mica, titanium containing minerals such as rutile, and other feldspar minerals (Celik, 2001). Quartz is stated as having a negative effect on the melting point of the feldspar, whilst the iron and titanium based mineral contaminants are known to have negative effects on color and quality of the product produced; these mineral contaminants must therefore be separated prior to application (Barns, 1997 & Celik, 2001). Mineral flotation and magnetic separation are the most common means of feldspar beneficiation. However, conditions vary greatly from mineral contaminant to mineral contaminant (Table 1). Some literature suggests feldspar can be floated with an amine, but this generally yields lower than acceptable recoveries and often still requires the magnetic separation of iron based minerals to achieve the desired grade (Amarante, 1997 & Heyes, 2012). Feldspar flotation can be further improved with the addition of hydrofluoric acid (HF) as a silica depressant and feldspar surface modifier, but this still requires the removal of some of the other minerals first. Rutile can be floated with an anionic fatty acid collector at a pH range of 7-8 or with a petroleum sulfonate at a pH < 4 (Celik, 2001), while mica can be floated with a petroleum sulfonate or an amine collector at a pH of 3.5."

Jan 1, 2016

By John Sasadi

The mining industry depends upon inexpensive water transportation. Today, large quantities of mined products are transported by ships over oceans, from continents to continents, over lakes and waterways to the ultimate users. Sometimes, the routes these Bulk Carriers travel cover only a few hundred miles, sometimes thousands of miles halfway around the world. Most of the products of the mining industries are relatively inexpensive. A significant portion of their cost to the ultimate users are in the cost of transportation and not in loading and unloading these commodities at the ports of origination or destination. So far, the industry has produced very efficient loading and un- loading installations, but has very little influence over marine transportation or the design of the vessels themselves. Very little was ever published dealing with integrated transportation systems properly correlating all phases of the operation; namely, loading, marine transportation and unloading bulk materials.

Jan 1, 1967

The Iron Ore Company of Canada (IOC) is the largest manufacturer of iron ore pellets in Canada and its customer base covers North American, European and Asian steel producers. The company operates a mine, concentrator and a pelletizing plant in Labrador City, Newfoundland and Labrador, as well as port facilities located in Sept-Iles, Quebec. It also operates a 418-km (260-mile) railroad that links the mine to the port. IOC has approximately 1,900 employees. Its shareholders are Mitsubishi Corp. (26.18 percent), Labrador Iron Ore Royalty Income Fund (15.1 percent) and the international mining group Rio Tinto, which is its major shareholder (58.72 percent) and operator, with activities in more than 40 countries throughout the world. The IOC was incorporated in 1949 and by 1954 it had completed the Quebec North Shore and Labrador (QNS&L) rail line. IOC began mining in Schefferville, Quebec by 1954 and closed those operations down in 1982. In 1962, IOC commissioned the present day Carol Project consisting of mining, concentration and pelletizing facilities in Labrador City, Newfoundland. In 2004, IOC shipped its one-billionth tonne of ore on the QNS&L Railway. In 2005, IOC celebrated 50 years of mining history. The company expressed an interest in reducing the amount of oversize material (>1 m x 1 m x 1 m or 3.2 ft x 3.2 ft x 3.2 ft) being produced and its subsequent downstream effects, including in-pit sorting and reduction, damage to mobile equipment and significant delays in the loading pockets and the primary crushers. To achieve this goal, an oversize reduction project was undertaken by the mine that, to date, has significantly improved upon baseline measures. One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion provided more resistance to the forces created by dynamic water and reduced the infiltration of the emulsion into the cracks and fissures of the rockmass, resulting in reduced amounts of oversize and more consistent fragmentation throughout the muckpiles. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realized. To determine the effectiveness of the oversize reduction project, IOC used a first-of-kind technology to assess fragmentation presented to the shovel at the digging face. A digital vision system (DVS) was installed on one of the shovels to capture images that were stamped with GPS locations. A large population of digital images were analyzed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jan 1, 2011

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device IntroductionTwo recent regulations have modified operators’ rock dusting schedules in order to meet compliance standards. First, the 80 percent incombustible requirement in intake entries has increased both on-section and out by the- section rock dusting. Secondly, the recent change to the respirable dust regulation has increased the number of respirable dust samples taken per sampling cycle. Previously, when only five samples were needed bimonthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule.The significant number of samples now required under new regulations, combined with the need to maintain 80 percent total incombustible content in active mining areas, require the schedules for respirable dust sampling and rock dusting to overlap. Although rock dust is considered a nuisance dust in relation to U.S. Mine Safety and Health Administration (MSHA) sampling, these overlapping schedules raise concerns about the amount of rock dust that potentially is included in the sample. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 effective Aug. 1, 2016, increasing concern that rock dust contamination may be an issue (MSHA, 2016). Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application, or to schedule rock dusting during a maintenance shift when the number of miners present is lower."

Jan 5, 2017

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The industrial Internet of Things (IIoT)—a concept that combines sensor networks and control systems—has been employed in several industries to improve productivity and safety. NIOSH researchers are investigating IIoT applications to identify challenges of and potential solutions for transferability of IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40% of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system based on low-cost microcontroller Wi-Fi boards, to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine, and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communications and tracking infrastructure. INTRODUCTION The nation’s approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communications with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there currently exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT). IoT is the network of physical objects or ""things"" embedded with electronics, software, sensors, and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator, and/or other connected devices [1, 2]. It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: internet and things. The first one pushes towards a network-oriented vision, while the second tends to put the focus on generic objects. The traditional internet can be viewed as an internet of computers —i.e., “things” connected to the internet are computers only. IoT “extends” the internet by allowing other generic things that are commonly found in our daily life, such as refrigerators and cars, to be interconnected via the internet, and thus creates a bridge between the virtual word and the physical world."

Jan 1, 2017

By PDF

Previous work has shown that significant, free milling gold values exist in the Ryan Lode ore. This project used pilot scale equipment to estimate the percentage of gold recoverable by gravity methods from the circulating load of a conventional, closed-circuit, grinding mill. The pilot scale flowsheet employed three stages of gravity concentration, hydraulic classification and batch grinding to simulate a full scale milling circuit. 172 kg (379 lbs) of Ryan Lode ore were processed, having a head grade of 4.8 g/metric ton (0.14 oz/ton). Results showed that simple gravity methods are capable of recovering 45-50% of the gold values in a concentrate grading in excess of 3430 g/metric ton (100 oz/ton). Of the remaining gold values reporting to the classifier overflow solids (80% passing 70 microns, 3.1 g/metric ton (0.09 oz/ton)) 89% were recovered from 48 hour bottle roll tests.

Jan 1, 1995

By T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

By Frederick C. Moore

This paper describes the original planning which actually resulted in the opening of a new aggregate plant located in central New York State. This plant, which is now named the Skaneateles Plant of The General Crushed Stone Company is unique in that the plant itself is a departure not only in design but in concept of operation from the normal aggregate plant the company has operated in the past. Whether or not the concepts which resulted in the Skaneateles Plant are economically feasible remain to be proven by the next few years of operation. By way of background data about our company which will help set the stage for this presentation, we currently operate seventeen stone quarries in the states of New York, Pennsylvania and Virginia. These quarries range in size from 200,000 tons per year to 1,500,000 tons per year with a total annual stone production of approximately 7,500,000 tons. We also produce about 1,250,000 tons of sand and gravel at six sand and gravel plants, 300,000 cubic yards of ready mix concrete, 1,500,000 tons of bituminous concrete, aglime and other minor construction materials. In many cases we are our own best customer consuming a large percentage of the total production of our own aggregates in our various ready mix and blacktop plants. Up to the concept of the Skaneateles Plant our operating facilities have been of the permanent type as opposed to the moveable or portable type plant. The steps involved in the case history of Skaneateles will begin with the basic economic requirements, market research, geologic surveys, land acquisition, zoning and financing and carry through to the final design and construction. We will attempt to show what some of the problems were, how we interpretted them and how we proceeded to solve them. The current results are apparent and can be analysed. The success of the total concepts of the Skaneateles Plant remains for future analysis.

Jan 1, 1968

By J. G. Nalven

On July 1, 1999, most domestic metal mines will have to report releases of toxic chemicals into the environment for the first time as required by SARA Title 313. Some of these reportable releases will appear huge in relation to reports by other industries. The reasons for the potentially large reportable releases, special considerations for mining operations, and strategies for dealing with the reports are described. Data composited from experience with several mining companies is presented in the context of a typical gold mine.

Jan 1, 1999

By T. H. Eyde

Natural Zeolites are a less expensive and in certain applications a superior alternative to organic ion exchange resins. Mining and metallurgical waste streams are difficult to treat because the effluents which contain potentially valuable heavy metals such as copper, lead, and silver are often highly acidic and contain significant quantities of suspended solids. Under rigorous operational conditions, certain natural zeolites can remove the metals, which if desired can be recovered by either elution or conventional smelting techniques. There are significant differences in cation exchange rate, selectivity and capacity as well as resistance to either high or low pH, blocking cations and tolerance to elevated or depressed temperature and pressure not only between different zeolite minerals but between the same mineral from different deposits. Applying natural zeolites to the treatment of mining and metallurgical waste streams depends on matching the specific zeolite to the effluent by characterization of the zeolite minerals.

Jan 1, 1994

By J. G. Pippenger

The Coteau Properties Company&apos;s Freedom Mine is a surface lignite mining operation located near Beulah, North Dakota. As part of the mining process, Coteau removes and replaces thin layers of suitable plant growth material (SPGM) generally ranging in thickness between one and five feet. Historically, tractor-scrapers completed this work; however, rising tractor-scraper costs and increasing haulage distances sent Coteau in search of a lower cost method resulting in the acquisition of a backhoe/truck fleet in 1995.

Jan 1, 1997

By Dr. Ing. Hermann Boldt

The Bituminous Coal Mining Industry of the Federal Republic of Germany produces nearly 100 million t/yr of clean coal. The largest coal mining area is the Ruhr District with dimensions of 100 x 40 km (65 x 25 miles). Figure 1: Here is the general administration of Ruhrkohle Akteingesellschaft RAG with its three divisions. Other coal mining areas in Germany are the Saar District and the Aachen District. Ruhrkohle produces 70 million t/yr of clean coal. The company operates 28 mines in the Ruhr District with an average raw coal production of 18000 t/day. Their average mining depth is 831 m (2740 ft.) and the average seam thickness is 177 cm (70 in.). Figure 2: Preparation plant reject is 44.6%. All following production figures will be with reference to raw coal because the raw coal production is the technically relevant number. Mining operations are mainly in non-dipping coal deposits whereby mechanized equipment for flat seams is also applied to deposits dipping up to 45? Coal extraction is done exclusively by the longwall method. Approximately 200 longwall installations are in production at any time. The average longwall length is 221 m (730 ft) ranging between 140 and 290 m (460 ft and 960 ft). The average longwall advance of all operations is 2.8 m/day (8.4 ft per day). Average production

Jan 1, 1977

By Matthew Holden, Jason Emery, Matthew Benjamin, Peter Craig

Over the last 25 years, through adversity and a growing level of risk mitigation, Australian Longwall mines have been using higher and higher capacity cable bolts for secondary support. A recent survey revealed 85% of Australian longwall cable bolts are a 70 tonne capacity pre-tensioned hollow post groutable system. Mines avoiding pumping cementitious grouts are sometimes using pre-tensioned resin encapsulated solid cable bolts of over 90 tonne capacity. Results from various industry and University research has led to manufacturer's fine tuning the construction of their cable bolts. A review of this research explains how smooth wire construction is now dominant. Aggressive shear has also led to some mines using 8 tonnes pre-tension instead of the previous common 20 tonnes pre-tension. Lower pre-tension acceptance is now leading to a greater use of threaded cable bolt end fittings, these are tensioned to 8 tonne using the drill motor torque. A recent development is the TEX cable bolt, a slim line threaded end fitting that fits with the drill hole like a standard rock bolt. This cable is being installed at the coal face as primary support off bolter-miners. The laboratory and in-situ testing of the TEX cable is presented. In a bid to improve gateroad development rates and ground support in the last several years, a 100 tonne tensile capacity Goliath cable system was developed. The latest development in resin anchored solid cables is a 110 tonne capacity cable bolt, with laboratory and in-situ testing results presented.

Jun 25, 2024

By Howard C. Homeyer

Coal and water are the two basic external feedstocks required for a coal gasification project. The WESCO project in northwest New Mexico, a joint undertaking of Texas Eastern Transmission Corporation and Pacific Lighting Corporation, will require about 25,000 tons of coal and approximately 7.5 million gallons of water each day to produce 250 million cubic feet per day (MMCFD) of pipeline quality substitute natural gas (SNG). The coal and water supply arrangement with Utah International, Inc. assures the project of an adequate supply of these two vital feedstocks.

Jan 1, 1974

By Harry Perry

Although the markets for coal in the United States have changed rapidly over the last three decades, the uses of coal, namely, to produce heat and power or coke have been left almost unchanged. The coke is used either as a chemical reducing agent alone or as a reducing agent and source of heat. Most of the heat and power markets for coal require no coal processing, although for more than 50 years, many proposals to skim the more valuable substances in coal before burning have been advanced. Thus, the only large tonnage market requiring processing of coal is high-temperature carbonization to make coke. At present, coal requires processing for some small markets, but for future potential large markets, such as gasification, conversion to liquid and gaseous fuels, and conversion to chemicals, coals will require more processing than is now being done.

Jan 1, 1962