Search Documents

By Brent Duncan, Doug Harding, Bob Stier

The 73rd Street Tunnel Project is part of “The Tunnel and Reservoir Plan” (TARP)also known as the Deep Tunnel Project, and is located in the Village of Bedford Park, County of McCook, State of Illinois. The project consists of a ø 4.42 meter × 2,060 meter long (14´-6? bore, 6,760 foot)tunnel. The completed tunnel is used as a bypass tunnel for the McCook Cup Reservoir Project. The project was awarded to Affholder Inc. of St. Louis, in 2000. The paper describes the project in which a new, high-powered open gripper type main beam machine was used in which high advance rates have been achieved using conventional muck haulage techniques. Features of the project include the installation of rock support consisting of counter-sunk rock bolts that are required to be pull-tested for strength per project specifications. Installation and testing of the bolts are done during the boring cycle. Muck haulage was done by conventional muck car train and hoisting at the construction shaft. As the site layout did not include a tail tunnel, the trains needed to be shuttled at the shaft bottom. Even with the bolting requirements and the muck haulage without a tail tunnel, the Affholder site personnel still achieved high advance rates on the 73rd Street Project.

Jan 1, 2003

By Martin G. Casto

Mixer-settler extractors, among the oldest forms of extraction equipment, have been used since the beginning of this century. Over the past years, a very large number of mixer-settler devices have been designed and operated. Both batch and continuous flow mixer-settlers have been used. The continuous flow mixer-settler extractor offers a great number of advantages over other extraction equipment. The main advantage of the continuous flow mixer-settler is that it is a compact device. A large number of stages can be assembled in a relatively small area, and more stages can be added fairly easily. Many improvements have been made in the design of mixer-settlers. These improvements occurred in almost every phase of mixer-settler' operation; interface control, mixer design, intrastage pumping, interstage flow of the two liquid phases, and stage construction. It is believed that Barstow1 used one of the first continuous mixer-settler extractors. This mixer-settler had concurrent flow within each stage and countercurrent flow overall. The flow for both phases took place by gravity. The Barstow device and other early mixer-settlers had no separate interface control for each stage, therefore, "tilting" of the stages was necessary. In 1934 Holley and Mott2 designed a mixer-settler in which the heavy phase was recirculated within each stage by the use of a valve controlled central line instead of by a pump. Gordon and Zeigler3 in 1939 were among the first to use an adjustable valve to control the interface levels in a mixer-settler, making tilting of the extractor unnecessary. In 1952 Coplan et al. 4 used a modification of the Holley-Mott idea to build a highly improved mixer-settler with flat common walls, and with the

Jan 1, 1971

By Carson Sharp Beltch

The determination of aqueous cyanide is accomplished by either detection in the sample as collected or by removal of the cyanide of the collected sample, followed by detection. The direct determination of the cyanide content of a solution can only be used in the simplest of systems, since many interferences can result in errors. Thus the most widely used method for total cyanide determination involve the reflux distillation of the sample using heat, acid and vacuum or air flow. The basic theory underlying this analytical approach is that by reducing the pH, the quality of molecular hydrogen cyanide will be in- creased and can be removed from the solution by elevating the temperature. The hydrogen cyanide is then collected in a caustic solution and analyzed. The general approach of removing the cyanide from the sample by distillation represented a major advance in this area of analytical chemistry. It enabled the determination of cyanide in many additional types of samples. When it became apparent that the tightly bonded cyanide complexes were not being detected by this approach, many methods fox complex ion destruction were proposed. These methods usually involved low pH adjustment with oxidizing mineral acids, coupled with the catalytic decomposition of the tightly hound complexes. All off the complexes except the strongest could he broken by these methods. The catalytic reflux distillation step has been found to have some negative aspects, since many materials that can be distilled with hydrogen cyanide will interfere with the color development step and result in a false positive reading.

Jan 1, 1981

By Christian Wawrzyniak

An analysis method for modeling compensation grouting based on the finite element method is presented. By this method the design parameters of compensation grouting, grouting pressure and grouting volume, can be evaluated. Also the subsidence of a building due to tunnel driving as well as the lifting of the building by compensation grouting can be simulated. The stress changes in the tunnel lining and in the foundation of the building are computed as well. The application of the analysis method is demonstrated on two examples for compensation grouting in combination with construction of tunnels.

By L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, Colorado, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained, and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward sloping (20 pct) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By John Parianos

"Seafloor mining provides significant potential economic benefits for many Pacific nations that may be "land poor" but "coastline rich," meaning they have the potential to utilize and profit from the mineral wealth within their Exclusive Economic Zones that extend 200 nautical miles (360 km) out from their coastlines. The Independent State of Papua New Guinea (the State) recognizes this tremendous opportunity and is taking a leadership role in this emerging industry by becoming a 15% partner in Solwara 1 (with an option to increase their investment to 30%).The Solwara 1 Project has been gaining momentum since Nautilus Minerals and the State signed an Agreement on April 24. This new agreement with the State in which they have staked a minimum 15% interest as a meaningful partner, underscores the State’s continued and widespread support for the Project. Signing of this Agreement was a historical occasion and a milestone achievement for Nautilus Minerals and the people of PNG.The machinery being built for the Solwara 1 Project is taking shape. The Seafloor Production Tools are now over 90 percent complete. Assembly of the biggest tool, the Bulk Cutter, was completed in April this year and assembly work on the Collecting Machine and the Auxiliary Cutter commenced in May and June this year respectively. The Riser and Lifting system, which will be used to transfer the mined material from the seafloor to the surface within an enclosed system, is over 50 percent complete. The critical path for the Solwara Project is to secure a suitable vessel arrangement. Nautilus aims to have this completed by the end of this year."

Sep 1, 2014

By Yucheng Li, De Huang, Yonghong Liu

Mine frictional resistance is one of the essential parameters of mine ventilation systems, and it is of considerable significance for the prevention and control of mine risks and accident hazards. Frictional resistance requires a lot of resources and time and has errors. To reduce the errors of frictional resistance, a regression model of frictional resistance is proposed based on the correlation analysis of the affecting factors. Through the comparative test analysis of seven regression methods, it is found that the classification and regression tree method for solving the proposed regression model has better performance than other methods. The least square error criterion is used to calculate and rank the importance of the factors affecting frictional resistance. The results show that the cross-sectional area of the tunnel, the support method, and the presence or absence of devices or pedestrian ladders have the most considerable influence on the prediction accuracy of frictional resistance. The support methods and cross-sectional areas are essential input variables. Through the combination test analysis of the influencing factors, the results show that the regression model does not have predictive ability when the number of input variables is less than 3 and the best predictive performance cannot be obtained using all the influencing factors. The best prediction model of resistance is to combine the shape of the tunnel, the support method, the presence or absence of devices or pedestrian ladders, and the cross-sectional area. The method proposed in this paper does not require a lot of resources and time investment, and the frictional resistance error is small. At the same time, it solves the problem of resistance prediction with incomplete data of influencing factors and provides a compelling new method for obtaining frictional resistance parameters.

Jan 28, 2022

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By Robert C. Freas, Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodities in this volume have as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as aggregates, fluxes, glass raw material, refractories, fillers, reactive agents in sulfur-oxide removal, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Holocene. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited availability in certain areas. Limestone and dolomite are so useful and so abundant that in 1989 about 798 Mt were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses. The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information.

Jan 1, 1994

By Rich Perry

HARRY HINDS: Our second speaker today is Rich Perry. Rich is the manager of leach and dewatering at Newmont Gold Company's Carlin operations. He has been the operator of Newmont's refractory leach development program for the past three years. Prior to joining Newmont in 1994, he was plant superintendent at the Big Springs and Jerritt Canyon Roasting Mills for Independence Mining Company. He graduated from the University of Nevada's Mackay School of Mines, and has lived with his wife and three children in Elko, Nevada, for the past 12 years. Please welcome Rich as he presents "New Facility Design Engineering: On-Site Versus Engineering Companies' Offices." RICH PERRY: Newmont Gold Company has been mining and processing gold ore at its Carlin, Nevada, operations since 1965. Processing is done using oxide milling, heap leaching, and whole ore roasting methods. Newmont began development of refractory leach processing technology at its research and development facility in 1988. The R&D staff focused on developing processing methods for low-grade refractory gold resources at Carlin that could not be economically processed by refractory milling methods. The term refractory ore refers to those ores that contain quantities of sulfides and/or organic carbon that result in low recoveries using conventional cyanide leaching. The R&D staff developed two potential processes deemed worthy of further testing: heap biooxidation to liberate gold occluded by sulfides and ammonium thiosulfate leaching for gold recovery from carbonaceous preg-robbing ores. These were piloted in small heaps by the staff of the R&D and Carlin metallurgical labs from 1990 through 1994. By 1994, Newmont's R&D and metallurgical staffs had unlocked the chemistry and kinetics of the two processes, and it was decided that the operations group would be brought in to begin development of a commercial plant. A project manager at Newmont's Denver office was assigned to the project. Scale-up issues such as biooxidation leach pad design; on/off heap heights; handling of various ore types during stacking and reclaiming; operating costs; and environmental, health, and hygiene concerns using a new process chemistry remained unanswered.

Jan 1, 1998

By K. Hanumantha Rao, K. S. E. Forssberg

The limestone deposit of Gâsgruvan, Sweden contains around 89.2 per cent of calcite. Conventional and column flotation studies have been carried out using sodium oleate and modified fatty acid collectors in the presence of sodium silicate modifier. The effects of collector and silicate concentrations, and particle size on the flotation response of calcite have been investigated. The results have been discussed in comparision to the performance of conventional and column flotation cells. The feed size is found to be a significant factor to achieve a high grade calcite concentrate either by conventional or by column flotation. The loss of selectivity at fine particle sizes is examined using a modified DLVO theory.

Jan 1, 1995

By A. Benchekroun

The phosphate mining industry is confronted everywhere in the world with financial difficulties and low prices which prohibit further investments and development of new mines even in regions with a comparative cost advantage (North America/ North Africa/ and Middle East). But old mines are being progressively exhausted/ and if no replacement mines come on stream in the near future/ we may soon find ourselves (around the year 2000) with a global annual production capacity of 160 million tonnes of marketable phosphate rock instead of the capacity of 200 million tonnes existing today. Unless prices improve/ phosphate rock/ a non-renewable resource and a vital commodity to world agriculture/ may turn to be in short supply to world fertilizer industry. Whatever the extent of recovery of fertilizer demand/ the expected decline of the production capacity during the 1990 I s is bound to cause the disappearance by the year 2000 of the important surplus characterizing today the supply/demand balance.

Jan 1, 1995

By G. R. Burman

Gilsonite is a brittle, natural solid bituminous resin, classified as an asphaltite. It is found in near-vertical veins in the Uintah Basin of Eastern Utah. Discovered well over 100 years ago by Samuel Gilson, this unique material has, since its finding, enjoyed a variety of commercial and industrial applications. Early uses for the product included black automotive paint and beer vat linings. Among its many important uses today are additives for oil well drilling fluids and cements, additives for sand castings for the foundry industry, reinforcing agent for asphalt pavements, and dispersing agent for black inks. Gilsonite is mined and processed in Bonanza, Utah, by two companies, American Gilsonite Company (AGC), an operating division of Chevron Resources, and Ziegler Chemical, a privately held company headquartered in New York.

Jan 1, 1990

By Z. T. Bieniawski, Christopher Mark

A new method for the design of long- wall chain pillars, called Analysis of Longwall Pillar Stability (ALPS), is described. The method provides estimates of the relative stability of different longwall pillar designs during all stages of their service life. The key issue addressed by ALPS is the magnitude and time-of-arrival of the longwall abutment loads applied to chain pillars. A field study was conducted and other available field data were analyzed in order to develop an approach for estimating the abutment loads. An example based on longwall experience in the Pittsburgh seam is used to illustrate how ALPS can be used in mine design.

Jan 1, 1986

By Henry A. Signore

The Appalachian coalfield, located in eastern Kentucky, Pennsylvania, Virginia and West Virginia, has been one of the most productive in the United States. Total production from the Appalachian coalfield during 1994 was 340.8 Mt (375.4 million st), or 37% of the 929 Mt (1 billion st) produced in the United States that year. This region contains various coal types from high- to mid-sulfur coal in Pennsylvania and northern West Virginia to low-sulfur, compliance steam coal and premium-grade metallurgical coal in eastern Kentucky, Virginia and southern West Virginia. The region's product is in high demand in domestic and export markets. Productivity continues to improve, resulting in the primary coal operators solidifying their market positions.

Jan 1, 1995

By Allen V. Reicks

Modern conveyor pulleys are welded steel structures subjected to dynamic loads. In this paper, fatigue notch and fracture mechanics methods are applied to several weld joints on typical pulley constructions. These methods are used to analyze field applications and are correlated with laboratory testing. Generalized approaches are presented which provide high confidence in pulley design with corresponding high reliability.

Jan 1, 1996

By R. J. Barnes

Consider a typical blast at a surface gold mine in North America. For example, the low-grade area of Bench 4000 at AMAX Gold's Sleeper Mine (Winnemucca, Nevada). Bench 4000 is 20 feet high (=6m) , and blast holes are drilled and sampled on a 14 foot by 14 foot square grid (a4m x 4m). A representative blast includes between 50 and 150 holes, encompassing 15,000 to 45,000 tons of material (w14,000 to 41,000 metric tons).

Jan 1, 1989

By Konrad J. Banaszak

At least for the time being, these seems to be general but not universal agreement that Mississippi Valley type ore deposits formed entirely or in major proportion from heated connate brines (e.g. 1) Even with that agreement, major questions remain. I will present a coherent geochemical model and look at alternative views in the context of that model. The pattern of the following discussion is 1) the general geochemistry of the ore fluid, 2) the density-temperature relations and possible mechanisms of flow of those fluids, 3) the mechanisms of transportation and deposition of the ore minerals, and 4) a summary of a coherent model of genesis. The data equivocally define much about the deposits. The answer is still elusive.

Jan 1, 1979

By Mark E. Gershon

The development of long term plans and schedules for strip mines now faces many companies, especially those developing large properties in the West. The rule of mining the lowest strip ratios first, while delaying equipment acquisitions and recouping investment the fastest, creates the situation where stripping ratios are too high in the latter years of mining operations. A program concept taking life of mine return on investment into account is developed in this paper to optimize mine scheduling and equipment acquisition. In addition, quality considerations (heat content, ash, sulfur, washability) can be considered by including the appropriate blending constraints to meet contract requirements.

Jan 1, 1983

By Peter Van deVelde

Many companies in North America because of economic or environmental reasons are considering reprocessing material from their waste ponds. The Japanese have developed highly specialized machines and techniques to reprocess industrial/mining wastes from settling ponds. This paper discusses the techniques and results of applying this technology to North American applications.

Jan 1, 1983