Search Documents

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

This study aims to investigate the reduction thermodynamics of ilmenite and pre-oxidized ilmenite, and reveals the isothermal reduction kinetics of pre-oxidized ilmenite concentrate by carbon monoxide. The results indicate that the ilmenite concentrate and pre-oxidized ilmenite concentrate can be selectively reduced by controlling the temperature. The pre-oxidation process leads to the breakage of complex mineral structure, and the formation of porous simple oxides, which is an effective method to increase the reduction and leaching rate. 

By J. C. Nigro

The potential use of prereduced pellets in the burden of the blast furnace continues to be a topic of interest. Several excellent papers have been written describing the theoretical and experimental rewards. (1) (2) (3) (4) (5) (6) (7) (8) (9) Significant increases in iron output and substantial savings in coke consumption are major advantages over conventional iron oxide pellets. The savings are especially important in areas where good coking coal is at a premium. Lower handling and transportation costs may also be factors favoring prereduction. When considering the overall cost of making and smelting prereduced materials the optimum metallization level becomes significant. An analysis by Agarwal and Pratt of the thermodynamic aspects of blast furnace operation with all prereduced pellets shows that the criteria controlling coke consumption depends upon the degree of reduction and upon the percentage of oxygen (present as FeO) removed by solution loss.(8) The authors state that although the chances of obtaining large fuel savings are greatly improved when metallization is high, reduction to the highest degree, which is costly, may not result in the lowest energy requirement per ton of hot metal; thus, over reduction could possibly result in wasted energy in the blast furnace.

Jan 1, 1968

By Augusto Andres Torres Toledo, João Felipe Coimbra Leite Costa, Luciano Nunes Capponi, Diego Machado Marques

Short-term mine planning to open pit requires defining diglines to orientate the excavation geometry. In deposits with multiple chemical variables, it is necessary to have more rigorous control over the feeding of the processing plant. This study analyzes the impact of incorporating multiple chemical variables, the risks generated by geological uncertainty, and the number and starting point locations of shovels in the sequential design of diglines. The objective is to maintain and preserve the low-grade variability, required tonnage, and continuity in sequentially selecting blocks. To achieve this, the probability distribution function of each chemical variable is used while attempting to maintain the ore grades as constant as possible. As it is difficult to maintain multiple elements with low variability simultaneously, the relevance of each chemical variable in the economic benefit is identified. Weights are assigned to signal the importance of each element based on its significance in the recovery process. Several diglines, consisting of sequential blocks, were generated on the same seed point to meet the weekly ore demand. Optimizing the stationarity of multiple chemical variables, accessing and reducing the geological uncertainty performed through geostatistical simulation of grades and transfers functions, considering the number and location of shovels, while meeting the operational restrictions of the selected blocks. The optimized digline with the multiple grades as stationary as possible is retained. The process is illustrated in a phosphate mine. The results show that the proposed method is viable and allows for a quick solution.

Jun 25, 2023

By D. R. Spears, C. E. Jordan

The U.S. Bureau of Mines examined the influence of turbulence on the fine bubble flotation of fine-sized (minus 40 micron) galena in order to improve flotation efficiency. Fine bubble flotation was carried out in a spinning-disk flotation cell and was compared to results obtained from flotation in a conventional cell at equivalent agitation levels. An automated electrochemical technique was used to monitor the turbulent velocity distributions of the fluid within the cell as a function of time and position. The velocity profiles were used to increase the precision of the fine particle, turbulent flotation model. While improved flotation response was obtained with intense agitation, the effect of bubble size was small. These results matched the model's predicted response for fine particle flotation.

Jan 1, 1989

By J. A. M. Cano

A brief introduction is made on the existence of sulphides in the top gas of the Midrex Shaft Furnace, giving consideration to the operation of the furnace and the liberation of sulphur as well as its consequential effects on the reduction process. The text shows a study of sulphur distribution in the pellet, emphasizing the importance of this distribution in relation to the liberation of sulphur during the reduction. A study was made to determine the sulphur compounds that exist in the pellets, showing ways of controlling the sulphur distribution and reducing its liberation?during the reduction.

Jan 1, 1989

By J. W. Oberholzer

This paper describes research being undertaken by the Chamber of Mines Research Organization (COMRO) which is designed to assist the continuous miner operator and section foreman in the performance of their jobs. The project will initially provide visual assistance to the miner operator, and later will semi-automate the mining (cutting) process. Using a technique known as "RF tagging," the project will also provide real-time or near-real-time information about the performance of the loading and hauling units to the section foreman, allowing him to quickly detect problems and take action where appropriate. The project is based upon the application of currently available technology, and the first phase is scheduled for in-mine testing within the next year.

Jan 1, 1991

By E. P. Fahrenthold, K. E. Gray

Introduction Brine reservoirs along the Texas and Louisiana Gulf coasts are currently under study to investigate the technical and economic viability of production wells designed to extract methane gas in solution. The effect of well pressure drawdown on reservoir rock and associated overburden material is important to well performance predictions and the analysis of potential subsidence problems. Consequently a series of compaction tests have been conducted on sandstone and shale cored from a test well drilled near Hitchcock, Texas, in order to determine the variation of mechanical properties to be expected over the producing life of the formation. Previous Work The referenced tests are part of an extended study of geopressured-geothermal reservoir behavior, including compaction (Jogi, Gray, Ashman, and Thompson, 1981 and Jogi, Kalra, Gray, and Thompson, 1981) and creep (Thompson, Jogi, Gray, and Richardson, 1981) tests of reservoir rock and related reservoir performance studies (Rago, Okhuma, Seperhnoori, and Thompson, 1985). Recent work has considered the nonlinear constitutive behavior of sandstone (Fahrenthold and Gray, 1985 and 19861, while additional experimental work is reported here. Geological structure and composition of the Hitchcock field from which the core samples were obtained is discussed by Light (1985). Experimental Procedure Compaction tests were conducted on cylindrical cores, nominally 2.75 inches in length and 2 inches in diameter, with independent control of the axial, confining, and pore pressures. Axial and radial deformation of the samples were measured in tests over a range of effective stress states expected to develop over the reservoir lifetime. The term effective stress as used here refers to the algebraic difference of the total stress and pore pressure, with compression taken as positive. Three types of compaction tests were conducted on the sandstone. In the uniaxial tests, axial total stress and radial strain were held constant as the pore pressure was reduced, similating one dimensional compaction which may occur during reservoir depletion. In the triaxial tests, radial total stress and pore pressure were held constant as the axial total stress was increased, duplicating conventional rock compaction test procedures. In the pore pressure drawdown tests, axial and radial total stresses were held constant while the pore pressure was reduced, in order to investigate differences in sample response to mechanical and pore pressure loading. Compaction tests were also conducted on shale material obtained from the reservoir overburden. The field coring process provided few consolidated shale sections sufficiently large to allow preparation of samples with the dimensions described above. With additional attrition during sample preparation of this brittle material, ultimate yield of the coring effort was limited. The few available samples were tested in uniaxial and triaxial tests similar to those described above. The use of displacement transducers to measure sample deformation avoided the difficulty of strain gauge installation on this material. Test Results The sandstone and shale both demonstrated nonlinear stress-strain behavior, with hysteresis and residual strain present upon unloading. Polynomial interpolation of the stress-strain curves was used in the calculation of incremental values for the loading and unloading moduli. Figures 1 and 2 show example axial effective stress-axial strain curves for triaxial tests conducted on sandstone and shale samples. The figures plot incremental stress and strain variables, defined as deviations from the state of prestress to which the sample was subjected. The state of prestress was varied between tests in order to investigate material behavior over the entire stress and strain space of interest. Tables 1 and 2 give the incremental moduli (Young's modulus and Poisson's ratio) as a

Jan 1, 1986

By E. Topuz

This paper discusses factors affecting the productivity of continuous coal mining operations. It analyzes design and operational relationships in continuous mining systems, and investigates how their productivity can be improved by selecting the number of headings, the dimensions of pillars, and the depth of cuts as well as the miner loading rate and tramming speed, the shuttle car payload and hauling speed, and the roof bolting cycle time. A computer simulator has been found very efficient in analyzing effects of section layouts and equipment operating characteristics on the productivity of continuous coal mining systems.

Jan 1, 1987

By J. J. Moore

Combustion synthesis or self propagating high temperature synthesis (SHS) reaction systems are discussed with respect to thermodynamics and kinetics. In particular, tile effect of the process parameters, ego particle size, AHf, ignition and combustion temperatures on these self sustaining reactions is discussed. Combustion theory is used to investigate the effect of the overall activation energy of the SHS reaction on the combustion front propagation rate and in obtaining a clearer understanding of the transition from stable to unstable propagation. Finally, examples of the application of combustion synthesis to advanced materials processes are made, in particular the synthesis of Ni-Ti -X intermetallic shape memory alloys, TiC-Al2O3 and ZrB2 ?Al2O3 ceramic composite materials.

Jan 1, 1991

By Mustafa Akser

Dwindling economic deposits of rutile (TiO2) prompted research on recovering it from secondary sources. One such resource is in Southwestern Turkey feldspar mining rejects that contain 5%-6% TiO2 mostly rutile. Previous studies could only upgrade the TiO2 to 36% TiO2 grade, claiming that the leftover flotation reagents on the surfaces of rutile and host minerals detrimentally affected upgrading of the rutile. As a potential remedy to this concern, a laboratory sample (from an operating feldspar mine in Milas, Turkey) was first caustic scrubbed, then air calcined at 400°C to evaporate the oily reagents. Subsequent physical separation of rutile included wet screening, gravity, magnetic, and electrostatic separation technologies. Such processes indeed improved the grade of the rutile concentrate up to 83 % TiO2 Low recovery of the TiO2 (<20%), was attributed to lack of full liberation of rutile, even at 125x44 micron range; interference with impurity minerals such as sphene and zircon; and simply the process inefficiency in upgrading the fine grains through conventional separation technologies for heavy minerals.

Jan 1, 1999

By G. Belardi, G. Marruzzo, P. Plescia

This paper presents the results of grinding tests performed on magnetite from Kiruna (Sweden) and on chromite from Skoumtza (Macedonia. Greece). Stresses were measured by XRD, which determined the variations in the characteristic structural spacings of the minerals both before and after, grinding in a HSM/250 Herzog laboratory ring mill. Anal Isis of the magnetite and c hromite crystallinstallin was performed hi measuring the broadening of the strongest diffraction peak (311). .Also, structural analysis on chromite was carried out using the Mikheev model. Ultrafine-grinding tests on the magnetite and chomite demonstrated that this type of treatment can induce profound variations m the surface-stress state. These included plastic variations of the cell followed by "chemical" stress with oxidation front the stricture to form hydroxide or carbonate, films. This can have a great influence on the mineral reactivity to flotation reagents

Jan 1, 1996

By L. G. Sobral, J. E. Hoffman, T. J. Keefe, A. J. Monhemius, O&apos

The kinetics of electrodeposition of gold from dilute solutions of alkaline KAu(CN)2 at different gold and free cyanide concentrations on a gold rotating disk electrode were investigated by use of a steady-state linear potential scan technique. The design and performance of a laboratory electrowinning cell with a reticulated nickel cathode, operating in the flow-through mode, for the removal of low levels of gold ions from aqueous cyanide media is described. During the batch recirculation of oxygen-free gold cyanide solutions, the gold concentration was reduced from 10 ppm to <0.5 ppm with current efficiencies of up to 80%. The influence of solution flow rate through the cathode and of the pore size of the reticulated nickel foam is discussed. The removal of gold ions from solutions of low ionic strength was also investigated.

Jan 1, 1993

By Keith G. Wallace, Gary K. Rogers

As a supplement to an analysis involving methodologies for the estimation of airflow resistance in shafts used for both ventilation and hoisting, a detailed shaft characterization survey was distributed worldwide. The survey provided detailed information which enabled verification of recommended velocities and established limitations on fill factors and relative velocities. This paper evaluates the information obtained for 37 shafts and presents a statistical evaluation of the results. Apart from airflow rates, conveyance rates, and physical characteristics, qualitative information regarding means of conveyance stability and velocity control techniques at unloading and loading points are also presented. Calculations of fill coefficient, free area velocity, and most importantly, relative velocity between the airflow and hoist, are conducted. These results are presented by frequency diagrams which illustrate the trends, as well as provide limitations for these parameters. The data illustrates that, commonly, the fill coefficient for two or more conveyances, does not exceed 30 %. A limit of 50% is suggested for a single conveyance shaft. A recommended free area velocity of 10 m/s (1,970 ft/min) for combined ventilation and hoisting shafts, is sup- ported by these results. Relative velocities of 30 m/s (5,905 ft/min) are most frequent and 50 m/s (9,840 ft/min) being a practical maximum.

Jan 1, 1987

By Syd Peng, W. B. Guo, F. Du, L. Yang, J. Yw. Cheng

The annual ICGCM China was initiated in 2014. Up to 2023, ICGCM China has been held 9 times. In the 9 conferences during the past 10 years, about 559 papers in 17 topical areas were presented and attendance ranged from 200+ to 400+ each conference. The 42nd ICGCM China was held in Xiangtan, Hunan, China, 10/20–10/22/2023. There were 86 papers presented in 26 topical areas. In addition, an MS and PhD Research Forum was held concurrently with 36 papers presented by MS and PhD candidates in mining engineering from 8 schools. The conference plays an important role in cultivating advanced degree student talents. In this paper, all 559 papers reviewed previously were summarized. In addition, the 42nd ICGCM China is used to illustrate the current and future development trends of coal mine ground control in China. It summarizes the 122 papers (including 36 MS and PhD forum papers) grouping into, and in terms of, 26 topical areas. In addition, its unique and innovative subject areas, short summary of developments as well as conference strengths and shortcomings will also be presented.

Jun 25, 2024

By Michael Brittan

The AARL elution process has recently been introduced to the North American mining industry by Bateman Engineers Inc. The process is described along with its noteworthy features. Design and operating considerations are discussed.

Jan 1, 1998

By D. L. Slyter

Coeur d'Alene Mines Corporation's Thunder Mountain project in Valley County, Idaho, is one of the most remote active mining operations in the US. High altitude, heavy snows, and proximity to wilderness complicate operations in this environmentally sensitive area. Mining is conducted by conventional open pit techniques while processing utilizes on-off heap leaching and Merrill-Crowe zinc precipitation. The project is one of a few similar operations which detoxify the leached ore prior to its removal from the leach pads. Both leaching and neutralizing ( detoxifying) circuits are closed and independent loops. After leaching, alkaline chlorine solutions destroy residual cyanide in the heaps. Calcium hypochlorite solution for the cyanide destruction is prepared by injecting chlorine gas into milk of lime solution.

Jan 1, 1998

By P. R. Taylor

The ability to process complex precious metal sulfide concentrates containing antimony and arsenic, in an economic and environmentally safe manner, is an important problem facing the mining industry in the united states. Preliminary experiments have been performed to evaluate the possibility of treating a complex sulfide concentrate to recover antimony and precious metals while fixing the arsenic and sulfur as calcium arsenate and calcium sulfate. The process involves the oxidation of the antimony and arsenic minerals in the presence of soda ash (to collect the sulfur dioxide and to keep the antimony and arsenic from forming volatile compounds), the selective leaching of the arsenic from the roast calcine with a heated caustic solution, the precipitation of the arsenic and sulfate with calcium hydroxide and/or calcium chloride, the reduction of the residual antimony (collecting the precious metals), fuming of the metal to form a marketable antimony oxide, and crucible reduction of the residue to obtain a gold and silver dore. Experiments have been performed to evaluate the first stage of this process. Batch experiments were performed using synthetic concentrates of stibnite and arsenopyrite. Variables that were studied included: mixture weight fractions, temperature, gas flow rate, oxygen partial pressure and time. All of the off gas dust and sulfur containing gases were collected and analyzed. The roast solid residue was subjected to arsenic leach tests and the leach solutions were subjected to arsenic and sulfate precipitation tests.

Jan 1, 1993

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By Michael Gilbert

In the world of tunneling the glamour is in the large diameter, long tunnels, but perhaps the number of projects for small diameter and short length tunnels are greater and generally have higher risk factors. Reasons for these higher risks include both the ?boiler plate? contract provisions used on these types of contracts, the technical specifications related to the tunnel work (versus the pipeline construction), the bid practices including measurement and payment and the construction. This paper reviews and comments on some of the key issues the authors have observed in recent major pipe-line projects that involve a small percentage of tunneling footage of the total contract.

By J. D. Miller

The sedimentary western phosphate deposits of Idaho, Montana, Utah, and Wyoming tend to be calcareous and generally carry a significant amount of dolomite along with collophanite. In some cases, such as the Smokey Canyon Mine, Afton, Wyoming, the ore will also contain mudstone, and in this case the aluminosilicate minerals (clay, feldspar, etc.) together with some dolomite are floated from the collophanite in column flotation cells with an amine in order to meet product specifications (31 % P205) (Service et al.). In other cases, such as the SF Phosphates Limited Mine, Vernal, Utah, the ore is treated by traditional fatty acid flotation of the collophanite with mechanical flotation cells (Weber, 1986). Preliminary tests have now been conducted to evaluate air-sparged hydrocyclone (ASH) technology for the flotation of western phosphate ore. For this preliminary study, samples were taken from the hydrosizer overflow stream (18-21 % P205) at the SF Phosphates Limited Plant in Vernal, Utah for scavenger flotation testing with the 2-inch ASH system in laboratories at the University of Utah. Selected design and operating variables are being studied, and the initial results show that satisfactory separations can be achieved by high-capacity ASH flotation at appropriate operating conditions. For example, with single-stage ASH flotation 80% recovery can be obtained with a scavenger concentrate grade of about 26% P2O5. These results are comparable to, or better than, those obtained at SF plant operations with conventional flotation cells and suggest that ASH flotation technology can be used to good advantage in the phosphate industry. Of course, research should be continued to consider other process streams, optimize the separation efficiency, and evaluate larger diameter ASH units.

Jan 1, 1993