Search Documents

By M. A. Raza

Cable shovels are capital-expensive and primary production equipment in many surface mines. The forces acting on the shovel dipper vary as the dipper moves through the muck-pile. The variations in the forces cause stress loading of the components of shovel and dipper resulting in unplanned downtimes, reduced shovel efficiency, and high mining costs. A potential solution to the above problems is the deployment of an intelligent shovel excavation (ISE) technology, with real-time formation identification, recording, and knowledge transmission capabilities. This research advances the ISE technology by developing dynamic model of cable shovel dipper using Newton-Euler techniques. The model includes the dynamic cutting and dynamic weight forces acting on the dipper as it moves through the muck-pile.

Jan 1, 2011

By Mina M. Shinouda

Brightwater West (BT4) represents the state of the art in utility tunneling, namely a long relatively small diameter, soft ground tunnel, with no intermediate shafts, under significant groundwater pressures, requiring very precise survey control in order to hit a small exit window. The tunnel is over 6.4 km (4 miles) in length, is expected to encounter active earth pressures of over 5 bars in glacial geology, and a planned hole through into a shaft eye constructed at 45.7 meter (150 feet) below the water table. Despite the fact that all of these challenges have been previously overcome in larger diameter tunnels, the technical solutions are much more challenging in a smaller diameter due to the lack of space available for implementing the equipment and techniques required. In addition to the technical challenges, the project is faced with many of the constraints designed to minimize the impact of these types of projects on the neighboring community and environment. The work shaft for BT4 is within 15.2 m (50 feet) of Puget Sound and is on a site that was previously occupied by petroleum storage tanks, and all of the tunnel muck has to be removed from the site by barge as trucking is not allowed by contract. The paper addresses the work performed during the preparation for tunneling stage of this project both in assembling the TBM and in preparing the site for its arrival.

By A. S. Winters

INTRODUCTION Homestake Mining Co. owns and operates the Bull¬dog Mountain mine near Creede, CO. Lead-silver con¬centrates are produced from ores extracted from narrow veins which dip from 1.04 to 1.39 rad (60 to 80°). An¬nual mill throughput is approximately 90 700 t (100,000 st). Ore shoots average 2 m (7 ft) in width and the ore is often weak, muddy, and poorly consolidated. Walls can be either strong or highly fractured along the strike of the veins. Cut-and-fill methods were initially selected to mine the deposit and considerable overhand mining occurred during the initial stages of the mine. Because of un¬stable ground conditions, mine management recognized that other methods would have to be employed. Undercut-and-fill mining was adapted to extract the loose ore from narrow veins and is presently the primary method used. Approximately 80% of the annual pro¬duction is extracted by this system. Loading ramps are positioned along the strike of the vein on 90-m (300-ft) intervals to allow for 45-m (150-ft) long cuts in each direction from the extraction raise. This interval was selected for efficient slusher operation and stope cycling. Loading ramps rather than chutes were selected for ore movement into 4.5-t (5-st) Granby-type cars because of extremely sticky ore conditions. Mined-out areas are filled with deslimed mill sands. Sand is pumped from the mill into two mine storage dams where the water is decanted. Each dam has a 544-t (600-st) capacity. Sand is pumped into the mine at a 30 to 40% slurry through 2195 m (7200 ft) of 51-mm (2-in.) thick wall pipe. When called for, sand is reslurried within the dams to a density of 55 to 65% and pumped to the particular mine opening requiring fill. Dry cement is added to the slurry prior to pumping. The capacity of the mine fill system is 20 t/h (22 stph). DEVELOPMENT Vertical development below the main adit level oc¬curs on 61-m (200-ft) intervals from an internal winze. Main haulage drifts or laterals are 2.7 x 2.7 m (9 x 9 ft) in section and driven parallel to the vein structures. Ground conditions generally dictate that better progress can be realized in the footwall than in the hanging wall. A distance of approximately 21 m (70 ft) is maintained between vein and drift openings to accommodate a smooth 18-m (60-ft) radius curve for crosscuts which are driven on 91-m (300-ft) intervals. Approximately 18 m (60 ft) of tail room is driven past the vein inter¬section to accommodate train loading. Ore and waste are hauled using diesel or electric driven locomotives operating over 18-kg (40-Ib) rail [762-mm (30-in.) gage]. Loading ramps are established above each crosscut¬ vein intersection. Scram drifts are then driven in the vein to determine the width and grade of the ore. If a prior decision to mine the block had been reached, then the scram is driven only far enough [about 12 m (40 ft)] to establish a drawpoint and scraper tail room. In most cases, the drawpoint is a 2.1 x 2.1-m (7 x 7-ft) cutout driven about 2.4 m (8 ft) into the footwall. On the level above, a raise bore station is established in the footwall to one side of the crosscut-vein inter¬section. The station is of sufficient size to accommo¬date a Robbins 41R raise boring machine. Support for the station is accomplished with 1.2 and 1.8-m (4 and 6-ft) roof bolts and wire screening. Once completed, a 152-mm (6-in.) concrete slab is poured and the raise drill set in position to center the 1.5-m (5-ft) diam hole approximately 1.8 m (6 ft) from the vein footwall. A 229-mm (9-in.) pilot hole is then drilled to the scram cutout below and reamed back to full diameter (see Fig. 1). STOPING Initial mining in a typical undercut-and-fill stope be¬gins from the top of the borehole. The initial cut can be either immediately beneath the track level or the old scram drift depending upon the particular situation. Cuts vary but are generally 2.4 to 3 m (8 to 10 ft) high. Support is accomplished by square-set timber, overhead caps, or roof bolts and screening depending upon ground conditions. Once the initial cut is removed, underhand timber and screen is installed and cemented sand fill placed. The stope is then ready for undercut mining. Prepara¬tion work begins with sinking 4.5 to 6 m (15 to 20 ft) on the borehole plus cutting a slot to the vein. As sinking progresses, hanging sets are installed to provide man¬way and service facilities. Hanging sets 1.7 m (5 ft 8 in.) long and 1.6 x 2.2 m (5 ft 4 in. x 7 ft 4 in.) in section are installed with steel hangers similar to shaft sets. Framed 203 x 203-mm (8 x 8-in.) timbers are made up in advance and shipped to the stope during sinking operations. When manway and service facilities are completed to the floor of cut to be mined, generally 3.65 to 4.3 m (12 to 14 ft) below the previous sand fill, the ore is removed to the hanging wall plus a round each way along the vein. Levelers or long stringers are then installed over the raise opening to support the work deck, slusher, and grizzly opening. All waste and ore from the sinking process is fed by gravity to the raise (see Fig. 2). Once the stope is equipped, mining pro¬gresses outward in each direction from the grizzly open¬ing. Stope equipment consists of 907 kg (2000 lb) pull air tuggers, timber skips, 11-kW (15-hp) ventilation fans, 15 to 22-kW (20 to 30-hp) electric slushers, 762 to 1270-mm (30 to 50-in.) scrapers, 67-mm (25/a-in. ) jackleg drills, as well as other drilling and blasting supplies. In narrow stopes [generally less than 2 m (7 ft) wide], no support is required for the underhand caps of the previous fill. Where wide sections in the vein occur, segment braces are installed beneath the caps to insure that the sand support cannot slip away from the hanging wall. Sections as great as 6 m (20 ft) wide and 4.5 m

Jan 1, 1982

By A. S. Hall

Significant pyrite often does not dissolve in the Sobek (1978) nitric acid extraction; therefore, the standard conservative approach is to estimate pyrite using sulfur present in the sum of the nitric acid and residual sulfur fractions. Alunite, when present, appears as residual sulfur. Because alunite does not generate acidic effluents, overestimation of AGP can occur if all residual sulfur is assumed to be undigested pyrite. Evaluation of 16 samples from the Florida Canyon Mine revealed that petrographic examination coupled with a modification of the Sobek method to include a 6 hour hot (250°F) 'nitric acid extraction resulted in a more accurate estimation of AGP.

Jan 1, 1999

By VASU GANGRADE

Large-opening underground stone mines pose significant ground control challenges, including the risk of massive pillar collapses. These collapses can result in dangerous air blasts characterized by tremendous force and high velocity. Estimating the velocity of these air blasts proves challenging due to the absence of accurate air velocity instruments near the mine portals. To address this issue, this paper proposes a novel approach that leverages closed-circuit television camera footage from the mine. Specifically, it employs the optical flow algorithm implemented in Python to estimate the velocity of the air blasts, providing a valuable tool for assessing and mitigating risks in such mining environments.

Feb 1, 2024

By J. P. H. Steele, M. U. Ozbay

As mining operations progress toward tele-mining and autonomous procedures, the need for machine performance monitoring increases. Presently, through a combination of vision, sound, and other subjective observations, an operator attempts to optimize the mechanical excavator’s operation. As the operator is moved away from the face in the case of tele-mining or completely removed for autonomous operation, the qualitative sensory input is lost. This lost information must be replaced with quantifiable sensory input. Chip formation detection may be a suitable replacement sensory input. Chip formation can be predicted with high confidence (>80%) through the analysis of the load waveform associated with the bit/rock interface.

Jan 1, 2002

By K. Short

Today?s modern mining operations have literally dozens of applications and systems generating data whose information very often, are not crossed or centralized for operational decisions. In remote locations, the information and situation awareness is typically limited to the location itself. In addition, access to that information is limited to a small, select group of personnel that have received training on how to interpret the results. When the situation affects another area of the mine then information is relayed to the applicable areas involved. Few workers have time to analyze the situation thoroughly, to see how it affects the mines symbiotic relationship within all areas of production. If the capability to correlate and measure events and situations that affect your overall key performance indicators are not in place, the opportunity to identify process improvement becomes more difficult.

Feb 27, 2013

By Kwadwo Osseo‑Asare, Isehaq Al‑Nafai

The hydrometallurgical processing of bastnasite is a well-known process that is used to extract rare earth metals. However, more accurate measures are required to enhance the efficiency of extracting and recycling rare earths. In this work, Pourbaix (Eh–pH) diagrams for La-, Nd-, and Pr-(F)-(CO3)-(SO4)-(Cl)-(NO3)-(C2O4)-H2O systems were theoretically derived to investigate the stability relations during the hydrometallurgical processing of bastnasite. The diagrams for RE-H2O systems show similar trends to the original ones drown by Pourbaix. The stability domains of RE carbonates were presented by RE-CO3-H2O systems with pH range of 4.5–11. In contrast, the diagrams for RE fluorides showed a large stability region of insoluble REF3 (pH ~ − 1.7–12). The decomposition behaviors of REFCO3 were studied by constructing Eh–pH diagrams for RE-F-CO3-H2O system. The stability regions of bastnasite species extend from nearly neutral to basic media (pH ~ 6.5–12). The acid treatment (using H2SO4, HCl, and HNO3) of bastnasite was investigated by constructing Eh–pH diagrams for REF- CO3-(SO4)-(Cl)-(NO3)-H2O systems. According to these systems, REFCO3 can be decomposed at pH ~ 6.5 when treated with H2SO4 and at pH ~ 1.7 when treated with HCl and HNO3 acids. On the other hand, the alkaline treatment of REFCO3 converts it to RE(OH)3 at pH ~ 11. The recovery of rare earths ions was studied with the aid of RE-C2O4-H2O systems which shows a wide stability region for RE oxalates in pH range of − 2–11. This theoretical approach explained the aqueous relations in the hydrometallurgical processing of bastnasite ore and it can improve the practical hydrometallurgical processing of such ores.

Feb 9, 2024

By Lyle W. Talbotr

The DeLamar Silver Mine is a Joint Venture between Earth Resources Company, the Canadian Superior Mining Company and the Superior Oil Company. The property is a consolidation of several old operations in the district. The more widely known are the DeLamar and Sommercamp Mines. The location is 20 miles northeast of Jordan Valley, Oregon and 55 miles southwest of Boise, Idaho. The mine is on the south slope of DeLamar Mountain in the Owyhee Mountains of southwest Idaho Initial interest started in 1969 with serious exploration beginning in 1970. The feasibility study was completed in 1974, and in 1975 Mountain States Engineers were retained to design and build the plant. Processing of ore began in March of 1977 with the first bullion poured in April of that year. The plant is currently processing some 2200 TPD of ore with a grade of four ounces of silver and 0.03 oz. of gold per ton of ore. Cyanide consumption is 2.5 lb/ton, zinc consumption of 0.3 lb/ton and flocculent consumption of 0.5 lb/ton. A flowsheet is shown as Figure I. The grinding circuit is of two stage design. The primary mill is an 18 ft. dia. by 9 ft. long semi-autogenous unit. The secondary mill is a 9 1/2 ft. dia. by 15 ft. long overflow ball mill. The mill discharges are combined and sent to 15 in. cyclones for classification. Cyclone overflow reports to leaching with the underflows reporting to the ball mill. The cyclone feed pump is an 8X6 metal case pump. The primary mill has 1000 installed horsepower and rotates at 68% of critical speed. The ball mill has 700 installed horsepower and rotates at 72% of critical speed. Because the primary mill is horsepower limited the ball charge is varied to maintain the desired throughput. The mill power is held at 980-990 HP by modifying the feed rate. Four inch forged steel balls are added any time the ore feed fails to reach 100 tons per hour for four hours. During periods of extremely hard ore, the ball charge has been as high as 14 v/o and at other times the mill has operated fully autogenous for weeks.

Jan 1, 1980

By Otto E. Zwanzig

You may think long before this talk has been completed that the speaker is belaboring the obvious. Please let me put to rest here and now any doubt which you may have in this regard by assuring you that is precisely my intent, and for a very specific reason. We all profess to know and recognize the obvious, but I am impressed increasingly how often we forget or fail to act upon the obvious. Shortly after starting my first job upon graduation from college, I was asked by my boss to participate in a course on practical communications, particularly as applied to conveying proposals effectively to the client -- be he customer or company president. The concept or philosophy underlying this program was so simple and obvious that in my youthful brashness I saw only a gross waste by the company of e good, solid $1930 in compelling me to take the course. The sequel to this experience occurred about five yews ago when I was directing a 300-man marketing group. At that time I enrolled a dozen of my department heads, and subsequently about a hundred other personnel, in the contemporary version of that sane program. Why? -- because they all knew the obvious, but I could see how imperfectly they were implementing it. Truly, a wide chasm exists all too often in our beliefs on the one hand and our practices on the other.

Jan 1, 1962

By F. Carew

Accurate knowledge of what mass and grade is to hand and where it is stored is key to mine efficiencies and overall profitability. In order to make the right decisions and align production with stockpile capacity, feed and contract demand, a clear and accurate view from production through blending and processing is required. The use of a mine production management solution can provide you with a high degree of confidence in and visibility into validated data as well as auditable and traceable material movements, activities and surveys. A robust calculation engine enables mass and grade changes to propagate to material movements and stockpiles to ensure you are getting the most accurate view at all times. Tracked changes in material balances can be readily incorporated in revised production schedules to close the loop. The availability of accurate, timely information, coupled with predictive trend indicators, is a significant advance in narrowing the gap between claimed and planned production that is common to many mines, regardless of commodity. This paper provides an overview of a Mine Production Management System (MPMS) and explains how the system helps address the challenges listed above.

Jan 1, 2011

By Harold Stocker

INTRODUCTION This presentation is concerned with the administrative and technical capability of the Atomic Energy Control Board (AECB) to assure compliance with the individual exposure limit for radon daughters (currently 4 WLM per year). It is not concerned with the epidemiological bases for setting the exposure limit. Moreover, the intent is to show how sophisticated methodologies and advanced technologies, applied to radon daughter concentration measurements in uranium mines, convey the spirit of compliance by providing better estimates than do the historical methods. These better estimates mean that more accurate and more precise estimates of each worker's exposure are determined using these more modern methods and devices. The estimates so derived should provide more convincing evidence to an individual worker that his assigned exposure is a valid indicator of his true exposure. In addition, a perspective on the exposure estimate in relation to the exposure limit is given as further evidence that an exposure limit is not the dividing line between "safe" and "unsafe" exposures. A brief description is given of the compliance aspects of the Atomic Energy Control Regulations and of the limitations of purely statistical non-compliance procedures. Most of the emphasis of the paper will be placed on the uncertainties associated with conventional radon daughter exposure determination and the means being employed (and anticipated) to reduce these uncertainties. NON-COMPLIANCE Under current Atomic Energy Control Regulations (1978), the annual individual exposure limit for radon daughters is given without reference to the possible methods of sampling and calculation of radon daughter exposure and without any reference to possible uncertainties or their magnitudes. This is common in such statutes, the details of sampling, calculation, error analysis, and so on, being left for licence conditions or provided as a specific guideline to the licensee on the matter of compliance with the Regulation. Since the exposure limit is contained in the Regulations, compliance with it is absolute, as with any other law. In Canada, a state of non-compliance with the radon daughter exposure limit exists when an exposure (attributed to an employee) is reported by the licensee to exceed the limit. No uncertainty in the measurements or in the overall determination of exposure is reported nor is any requested. Removal of the worker and the loss of his services are the immediate and direct penalty suffered by the licensee for failure to maintain the exposure at, or below, the limit. A worker may be re-instated to employment for the balance of the reporting period only if the licensee can assure the AECB that further significant exposure to the worker will not ensue. In other jurisdictions, such as the United States, non-compliance is defined on a statistical basis. For example, NIOSH, the National Institute for Occupational Safety and Health presents procedures for calculating the 95% Lower Confidence Limit (LCL) in order to "compare the results of occupational environmental sampling to an occupational health standard and make a decision with a known chance of making an incorrect decision that a state of non-compliance exists" (Leidel and Busch, 1975). (In the nomenclature of this presentation, exposure limit would be used in place of "standard", in the NIOSH sense). Furthermore, it is emphasized in the NIOSH document that such numerical comparisons "are necessary only if the sample mean is greater than the standard". The NIOSH document points out, quite correctly, that the "statistical procedures presented below will not detect and do not allow for analysis of highly inaccurate results, i.e., systematic (non-random) errors or mistakes ... If a systematic error is known to exist in an instrument or analytical procedure then correct the sample mean of the data before analyzing for non-compliance". It is certainly not the purpose of this paper to criticize the sophisticated statistical approach to non-compliance as given in the NIOSH document or in similar approaches used in other jurisdictions. Rather, the purpose is to approach, with some introspection, the question of the determination of exposure by the employer for his employee and especially the employee's understanding of, and confidence in, the accuracy of the exposure determination and its relation to the exposure limit. DETERMINATION OF EXPOSURE Historically, in uranium mines, exposure to radon daughters for an individual miner

Jan 1, 1981

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By David P. Keller, George Podolsky

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The world production of iron oxide pigments is estimated by the authors to be between 350 and 400 kt. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test which now has some 20,000 years of exposure. In addition to abundance, iron oxides (about 7% of the earth's crust) have the advantage of low cost, permanency, and are non- toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when these properties were desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States, the combined production of natural and synthetic iron oxides produced sales of over $97 million in 1980 (Spimad, Jr., 1980), increasing to $138 million by 1990 (Templeton, 1990) NOMENCLATURE With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products that are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a competitive commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and are able to command a premium price over iron ores used for steel manufacturing. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary particles are produced as opposed to the use of comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1994

By R. J. Sweigard

One of the foremost problems in reclaiming prime farmland is compaction of the subsoil which is caused by the reclamation equipment. Wheel tractor-scrapers are most commonly used to replace subsoil and have been blamed for the majority of the compaction problems. Two methods of alleviating this problem that are presently being considered are mechanical subsoil loosening machines and truck- shovel combinations for subsoil handling. A field study was conducted in which dry bulk density measurements were taken in an effort to determine the effectiveness of truck-shovel combinations and subsoil loosening equipment in reducing bulk density in comparison to typical scraper replacement.

Jan 1, 1987

By SHANTAE LEE, ELAHEH TALEBI, Frank A. Drews, ROGERS W. PRATT

Fatigue is a relatively well-investigated topic in the surface transportation industry with a research focus on sleep deprivation and disruption. This paper examines fatigue in mining operations. While mine operators are using or currently introducing technology to monitor fatigue, there is little work that focuses on the operators’ experience of fatigue and the acceptance of fatigue-monitoring technology. Focus groups were conducted to investigate these topics. The results of this research suggest that current fatigue-monitoring systems lack validity, reliability and user acceptance. Overall, these results emphasize the importance of a socio-technical systems perspective to guide interventions aiming at improving miner health and safety.

Blast vibrations induce sounds within neighboring residences. A house wide vibration and sound monitoring system was installed in a West Virginia home which was subjected to blasts at varied distances and direction. Eighty-nine blast events were monitored and analyzed for this case study. Fifteen channels of data were collected including three triaxial geophones, one airblast microphone, one uniaxial geophone mounted to the wall of the house (response channel), and four microphones that recorded CD quality sound waves inside the house. Each of these channels was recorded on the same time reference and scale allowing for direct comparison of the waveforms. The response channel signal was easily separated into ground vibration induced and airblast induced movement due to the differences in their times of arrival. This response channel was then compared to the sounds recorded inside the home to determine which component of blast vibration induced the maximum sound response inside the home. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast. While for blasts beyond 762 meters (2,500 feet), the maximum sound response inside the home was caused by ground vibration without exception. When airblast was identified as the dominant sound generator in the house, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator in the house, the peak amplitude of sound was not related to the amplitude of ground vibration. In these cases, sound amplitude was driven by the conditions present in the house such as loose items, doors, and windows creating sudden peaks from falling or slamming. In the same respect, sound amplitudes varied depending on where the sound was recorded. Different rooms generated very different sounds based on the contents of the room. Findings from frequency analysis showed that the frequency content of sounds inside the house were not related to frequency content of airblast or ground vibration regardless of source suggesting that residents would have difficulty determining the source of blast induced noise in their homes.

Jan 1, 2010

By Abhilash, S. Sarkar, T. Venugopalan, P. Meshram

"To explore blast furnace slag as a secondary resource for rare earth elements (REEs), blast furnace slag containing lanthanum (La), cerium (Ce), erbium (Er) and neodymium (Nd) in concentrations of 17, 16, 4 and 44 ppm, respectively, was processed with sulfuric acid while optimizing the parameters of acid concentration, temperature and pulp density. The experiments showed that recovery rates of 92, 36, 35 and 52 percent for La, Ce, Nd and Er, respectively, were achieved at 1 to 5 weight/volume (w/v) percent pulp density using particles smaller than 250 µm and treating with 1 M sulfuric acid for one hour at room temperature. Raising the temperature to 95 °C promoted the dissolutions of Ce and Nd to 89 and 84 percent, respectively, for the same 1 M acid concentration and one-hour duration at 5 w/v percent pulp density. Cyanex 923 was preferred over Cyanex 301 for the purification of REEs from leach liquor. In another route, the leach liquor was subjected to precipitation with 0.5 to 1 M oxalic acid, resulting in a product with 4 to 5 percent concentration of REEs.IntroductionRare earth elements (REEs) are important materials in numerous high-technology applications, but they have high supply risk, giving rise to the study of new sources. The recycling of REEs has been well researched, especially on a small scale, but has not been widely implemented. Less than 1 percent of REEs were recycled in 2011 (Binnemans et al., 2013). REEs occur in a large number of minerals in oxidic compounds, such as oxides, carbonates, phosphates and silicates, and are present as mixtures at 10 to 300 mg/kg concentrations in many rock formations, such as basalts, granites, gneisses, shales and silicate rocks. The most abundant REE in the Earth’s crust is cerium (Ce), at a concentration of 20 to 70 mg/kg, followed by neodymium (Nd) and lanthanum (La), with heavier REEs being less abundant (Binnemans et al., 2013). REEs occur in nature in their oxidized forms in salts and minerals due to their electropositive nature and high affinity for oxygen. The possibility of recovering REEs"

Jan 1, 2017

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By A. J. Basu

Rock mass properties testing for determining strength parameters is an integral part of geomechanics. These tests are performed either in a laboratory environment or in a field (in-situ). The authors share their experience in using numerical modelling in simulating the laboratory test procedures. This approach helps studying the rock breakage and failure mechanism more efficiently and provides a high degree of visualization. Moreover, imperfections and discontinuities can be easily incorporated in these models. This capability of providing arbitrary fractures and discontinuities facilitates in building a large knowledgebase of rock strength and failure mechanisms. This knowledgebase may then be used to generate heuristics for determining rock strengths for rock mass with fractures and discontinuities.

Jan 1, 1997