Search Documents

By S. D. Thompson

Conveyor belt haulage has become the preferred mainline transport method in under-ground coal mining, especially for multi-unit mines. Optimum designs for belts (width and speed) and surge bins (placement, capacity, and discharge rate) are necessary for minimizing haulage cost. Two computer simulation models, CMaCS and BELTSIM, available for optimizing these designs are compared. These comparison include: modeling, input data requirements, statistical flexibility, accuracy of simulated loading, and execution time.

Jan 1, 1989

By D. T. McMurray

INTRODUCTION Shabanie mine, situated some 180 km east of Bula¬wayo, has been a producer of chrysotile asbestos for more than 50 years. The ore bodies occur in serpentinized dunite, which overlies talc-carbonate schist. A zone of relatively competent rock of varying thickness occurs between the schist and the ore bodies, which are gen¬erally less competent. The hanging wall of the ore bodies is economic, and the hanging-wall serpentine carries a variable subeconomic amount of fiber. It is important to note that, in general, the ore body competence is less than that of the foot and hanging-wall formations. Historical After surface operations ceased, cut-and-fill stoping was used to win ore from underground; this was success¬ful until the increasingly stoped-out area caused insta¬bility in the stope pillars and back. Consequently, dur¬ing the early 1950s, a gradual change to cave-mining methods was made, the ore being won by hand lashing in drawpoints, situated in the basement of the stope blocks, and passed through orepasses under gravity to the haulage level some 13 m below. About this time, interest was focused on the sub¬level caving method in use in Swedish iron ore mines: it was felt that it might be applied economically to the Shabanie ore bodies. Accordingly, in 1958, an experi¬mental stope block was laid out in which sublevel inter¬vals and extraction tunnel spacing were 9 m. The tun¬nels (ring drilling drives) were oriented on strike-in contrast to the Swedish system, in which crosscuts that retreat from hanging to footwall are used. The advantages of the method were quickly appre¬ciated by the operating personnel and, despite the in¬evitable teething troubles pertaining to the introduction of any new mining method, it was not long before sub¬level caving was providing a high proportion of the mill feed. The disadvantages also became apparent at an early stage, however, and, from that time to the present, continuing modifications have been made to mining lay¬outs in an effort to improve ore recovery. GENERAL DESCRIPTION OF METHOD The mine is served by a vertical hoisting shaft, in which two skips, a man cage and a service cage, provide adequate capacity for production requirements. The rock hoist is a Ward Leonard control hoist, in which two electric motors drive a common gearbox. The man winder is driven by an a-c motor. Several auxiliary shafts provide secondary egress and intake and return ventilation. Main haulage levels are above (Fig. I a and b). Blasthole fan patterns are drilled by drifters of 100 mm bore, drilling 41-mm holes; when a sufficient strike length has been drilled, a slot is cut in the upper¬most sublevel and the rings are broken into the slot. Initially, a limited tonnage is drawn, since it is essential to ensure that the hanging wall caves behind the retreat¬ing stope face. Once this has been established, maxi¬mum tonnage can be drawn, as described later in this chapter, under the heading "Draw Control." The broken rock is loaded by 0.14 and 0.20-m3 load¬ers into cocopans (rocker-dumping type of tipping truck), which are hand trammed to orepasses, discharg¬ing on the haulage where 11-t electric trolley locomo¬tives haul 3.95-m3 Granby cars to the main shaft bins. As is evident from Fig. 1, the layout is simple, the block is brought rapidly into production, there is a high degree of selectivity and flexibility, and the result is a low-cost high-productivity mining method. DEVELOPMENT Main haulages are developed at 3.2 x 3.2 m, and once the service winze connections have been completed the development of the sublevels is undertaken. The footwall drives are cut first, to obtain access to the block. These ends are of the standard section, 2.4 x 2.8 m, and from them crosscuts at intervals of 70 m are driven through the ore body to the hanging wall. These crosscuts are used to supplement the geo¬logical information previously obtained from diamond core drilling, and they provide additional and more de¬tailed data on fiber percentages and lengths, structural features, and other relevant criteria which are used to build up the geological assessment of the area and to classify it in terms of the geomechanics rock classification (Laubscher and Taylor, 1977). The crosscuts also allow the necessary orepasses to be sited conveniently so that tramming distances from the loading points are not excessive. Development Drilling Once the skeleton development has been completed, the extraction headings are developed at 2.4 x 2.4 m as shown in Fig. 1. Standard development practice is to use crews of a machine operator and his helper, equipped with air-leg mounted jackhammers, to drill rounds of 1.8 m with integral tungsten carbide tipped drill steel. The round drilled is a normal drag round, as shown in Fig. 2, but considerable attention is paid to the drilling of the perimeter holes to use effectively the

Jan 1, 1982

By Mahmoud Sepehrmanesh, Verya Nasri

The purpose of this paper is to outline the advantages and disadvantages of single tube and twin tubes for subway systems. Different aspects such as diameter of the tunnel (tunnel spaceproofing), configuration of subway line and stations, impacts on passenger safety and evacuation, ventilation system as well as rail system for each solution were evaluated and compared. In addition, a multi-criterion approach is established to facilitate the decision making for these two different subway systems. The practical example of a mega project has been discussed and the details of the decision-making process has been explained. This proposed multicriterion can be used to facilitate selecting the best subway system in any urban areas.

Dec 1, 2022

By P. M. Pettit

Hydrologic investigations at Gold Quarry began in 1989 and continued through 1991. Hydro-stratigraphic units include Tertiary sedimentary rocks, Paleozoic siltstones and carbonates. These units display complex and variable aquifer parameters as a function of faulting and hydrothermal alteration, creating compartmentalized hydrologic domains. Testing has included step-tests, spinner production logs and constant discharge tests. Two Three-Dimensional Finite Element Models have been developed, one for optimizing the pit dewatering system and the second for predicting regional impacts of dewatering. Aquifer testing and long term pumping have been used to calibrate both Finite Element Models.

Jan 1, 1992

By L. A. Readdy

Defining classes of ore using geostatistical methods that match historical classifications has presented problems in the past. A simplistic and practical approach to this problem is presented. An example of the approach is presented using a porphyry type system as a case study. The technique described uses area of drill hole influence and known conditions from similar deposits, or the production history of the deposit being studied. It provides a practical bridging mechanism for defining the class of ore on a block-by-block basis using .the error of estimation value developed during kreiging. The approach provides a filtering method that refocuses attention on the adequacy of drill hole spacing.

Jan 1, 1985

By W. Moser

During the ten year span from 1978 to 1987, the number of fires which occurred in under-ground coal mines doubled from the previous ten years. Anyone involved with underground coal mines is well aware of the associated tragedy that can result from these fires, both to personnel and to property. Every day mine management and mining personnel face this threat of a possible mine disaster or fire. Their ability to deal with such a situation safely and effectively depends on the level of emergency preparation developed and maintained. As a direct result of the ever-increasing interest in the Mine Emergency Preparedness Program and the Mine Fire Training Programs currently being conducted, the Emergency Preparedness Center was created. As a branch of the Mining Extension Service at West Virginia University, the Center provides preparedness training at several different levels on a varying range of topics. Classes are conducted at a new especially-designed training laboratory at the National Mine Safety & Health Academy in West Virginia. By maintaining the proper equipment and levels of training allowing for immediate response, the personnel who are part of the Center believe that the impact of a mine fire or other such emergency situation can be minimized. This paper will present recommendations for maintaining an efficient mine emergency preparedness program and will provide information regarding the Mine Fire Training Program as conducted by the Emergency Preparedness Center and describe the advantages of the newly constructed training facility.

Jan 1, 1993

By Yi Luo, Hua Jiang

A roof bolting drilling operation in an underground coal mine can expose the operator to a high concentration of respirable coal and crystalline silica dusts (smaller than 10 µm). Overexposure of high-level quartz dust for a roof bolter operator can lead to the development of silicosis in as little as three years [1]. This study proposes a drilling control algorithm for the bolt hole drilling process. This algorithm can be integrated into a current drilling control system on the roof bolter machinery and is expected to reduce the generation of respirable dust while enhancing the energy efficiency of the roof bolter machine. In addition, the drilling efficiency and bit condition can be evaluated while drilling based on the real-time feedback parameters. This capability enables the algorithm to ensure the drilling is performed under a relatively high energy efficiency with less respirable dust generation and to avoid drilling with an excessively worn bit that can cause bit clogging or steel buckling failure.

By N. K. Dumakor-Dupey, K. J. Bansah

"We made site visits to determine potential environmental issues caused by artisanal and small-scale mining (ASM) in the Tarkwa Mining Area (TMA) of Ghana. Activities of the diggers were observed to degrade vegetation, land and water. Improper handling of mercury was also identified as a major threat to people and ecosystem. Large abandoned pits and trenches posed fall traps to farmers, hunters and wildlife. We argue that lack of adequate monitoring and regulatory enforcement by Ghanaian authorities, together with inappropriate mining processes, probably due to lack of technical expertise are contributing factors to the environmental issues of artisanal and small-scale mining in the TMA. INTRODUCTION Environmental degradation caused by artisanal and small-scale mining (ASM) has been a major concern to many people and governments around the world. ASM is often associated with health, safety and environmental issues in communities where it is practiced (Kitula, 2006; Asiedu, 2013; Sousa et al., 2010). Some of the environmental issues that have been reported include land degradation, mercury contamination, cyanide release, and pollution of rivers/streams. These issues have been attributed to improper mining methods, inefficient technology, lack of technical training and environmental awareness, and lack of regulatory enforcement (Serfor-Armah et al., 2005; Bansah et al., 2016a; Hentschel et al., 2002). In Ghana, ASM typically occurs in rural communities, providing jobs to many people and contributing towards socioeconomic growth of the country (Banchirigah & Hilson, 2010; Bansah et al., 2016b; Osei-Kojo & Andrews, 2016). As a result of the environmental issues, many people have called on government to develop drastic measures to control ASM operations. It is in this regard that this paper examines potential environmental issues caused by ASM in the Tarkwa Mining Area in Ghana, and suggests mitigation measures to ensure environmental sustainability. ASM in the area comprises of registered (licensed) and unregistered (unlicensed) operations that adopt surface or underground mining methods to exploit gold-bearing materials. Surface operations typically involve clearing of vegetation, removal of overburden, excavation of mineral deposit, washing/grinding of excavated gravels and processing with mercury. Except grinding, washing and mercury recovery, underground operations are conducted below ground with limited impact on the surface. Alluvial mining is also commonly practiced in streams and along river banks. These activities can have devastating impact on biodiversity of the ecosystem. To achieve the objective for this study, field visits were made to ASM sites to observe operations and interact with diggers. Visits were also made to host communities of ASM and government officials to obtain their perspectives on ASM in relation to environmental impact. The study area (Tarkwa Mining Area) is located in the Western Region of Ghana (see Figure 1). It is endowed with natural resources such as gold and manganese. Hence, mining is the major economic activity in the area. ASM is widespread, with 15 registered operations and several unregistered mines. The environmental issues observed in the study have been grouped into three main categories: vegetation and land depletion; water quality and pollution issues; and mercury contamination issues."

Jan 1, 2017

By M. A. Trevits

Mine seals are used in underground coal mines throughout the United States to isolate abandoned mining areas from the active mine workings. The objective of adding inert gas to a sealed mine area is to quickly reduce the oxygen concentration in the sealed area to a level that will not support combustion. In the US, this process is typically conducted from the ground surface and because surface-to-mine access is constrained by so many variables, it is very difficult to provide a source of inert gas to the place where it is needed underground. To alleviate this problem On Site Gas Systems, under a NIOSH contract, built a nitrogen (N2) generation plant that operates in the underground environment. The purpose of this work was to create a reliable in-mine mobile plant that would extract N2 gas from the mine atmosphere and use the gas to create and maintain a safe sealed mine area. The plant is based on a novel design using pressure swing adsorption technology and is sized to fit on a standard shield car or mine dolly for easy transport in and around an underground coal mine. The plant is capable of producing about 900 scf/min of N2 gas at ambient mine conditions. After an exhaustive series of laboratory tests, the plant was field tested at the NIOSH Safety Research Coal Mine (SRCM) where a portion of the mine was sealed and rendered inert. During the test, the movement of the injected gas was monitored at several underground points to observe the progress and extent of the inerting process. This paper describes the plant design and the results of the field test at the SRCM. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By R. L. Zick, D. C. Finn

Introduction The high-density sludge process was originally developed by Bethlehem Steel Corp. for use on acid mine drainage (AMD) and diluted waste pickle liquor discharges requiring continuous chemical-treatment. This work began in the early 1970s and was first put into practical use around 1973. To date, there are approximately 15 operating systems that have been installed to treat mine drainage in the United States. In addition, there are another 10 systems installed outside of the United States. The dense-sludge process is an innovative and improved method for treating acidic metal-bearing streams in a manner that minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge-recycle process that forms particles with a low affinity for water. These particles are unlike conventional metal hydroxide solids that contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations that combine with calcium ions in lime-based treatment systems to form gypsum crystals. Compared to the form generated in conventional lime treatment systems, the physical form of the gypsum is radically altered when the dense-sludge process is utilized. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. The dense-sludge particles settle faster, dewater more readily, are more easily pumped and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered. In general, the conventional and dense-sludge treatment processes are very similar. The changes required to implement the dense-sludge process are minor, and, typically, much of the existing equipment can be utilized. The net results of the process are: reduced operational costs associated with sludge generation, improved process control (particularly pH control), reduced gypsum deposition (i.e., less scaling) on system components and reduced sludge generation resulting in less return water for treatment. Despite the relative simplicity of the process, the application of the technology requires careful discrimination, and the "experience factor" for implementation is an important consideration that should not be over looked.

Jan 1, 2000

By M. Hepokoski, M. Klein

"Mine refuge shelters are designed to protect mine workers from hazardous environmental conditions after a mine disaster, but high temperature and humidity levels inside these shelters may pose a significant safety risk. Due to the safety risks associated with human testing, detailed thermal models of shelters and human occupants have been developed using TAITherm simulation software. These models are used to predict the temperature and humidity within the shelter resulting from metabolic heating, evaporation due to sweat and respiration, moisture and heat from the shelter’s carbon dioxide scrubbing system, and heat transfer within the shelter. A detailed human thermoregulation model simulates the sensible and latent heat generated by the shelter occupants, and predicts the occupant’s body core temperature and moisture lost due to sweating and respiration. This information is used to assess the safety of the shelter. In this paper we will review technical details of the human thermal model, validation comparing the human model to human subject test data, and results of a mine shelter analysis. INTRODUCTION Portable mine refuge chambers are used in US coal mines to provide protection to mine workers from hazardous conditions following a traumatic event. Although these shelters are designed to supply clean air and sustenance for up to 96 hours, prolonged exposure to the mine shelter environment itself can pose a substantial risk to human safety. Heat generated by the shelter occupants combined with heat from the carbon dioxide (CO2) scrubbing system can raise the shelter interior temperatures and relative humidity to dangerous levels that can lead to heat stress in humans. Unfortunately, the thermal burden associated with mine shelter exposure is not well characterized due to potential hazards associated with underground human subject testing. In order to assess the thermal burden on people within a mine shelter environment, a detailed thermal model was created to accurately predict the temperatures and humidity within the shelter, as well as the impact of these environmental conditions on human occupants. The model consists of a mobile inflatable tent-type mine shelter, 23 humans, and also includes the surrounding mine environment. The thermal simulations were performed using ThermoAnalytics' validated commercial heat transfer prediction code, TAITherm (v12.0). Additionally, TAITherm's Human Thermal Module (HTM) provided the capability to simultaneously model the thermo-physiology of 23 unique humans contained within the mine shelter. The human thermal models accounted for the thermal interaction with the environment and also provided a core temperature response prediction, which can be used to evaluate survivability in heat stress situations [1]."

Jan 1, 2016

By R. P. Upadhyay

The Deserado Mine, located in northwest Colorado, is an underground coal mine designed to produce 1.225 million tons (1.35 million short tons) of clean coal per year for the Bonanza Plant located in northeastern Utah. Coal is transported to the power plant via a 61 kilometer (38 mile) captive railroad. Most of the surface facilities and the stationary underground equipment is controlled and continuously monitored by the computers located at the surface control room. In addition to system control, the computer also continuously monitors vital environmental conditions using sensors located at various critical locations underground. The system's advantages are increased mine productivity and safety.

Jan 1, 1988

By Karl A. Olsson

The Glenharold Mine is a surface mine operated by Consolidation Coal Company. The mine is located approximately 90 kilometers (55 miles) northwest of Bismarck, and 3 kilometers (2 miles) southeast of Stanton in west central North Dakota. Glenharold has a nominal design capacity of 3.0 million metric tons per year (3.3 million short tons per year). With the exception of local coal sales, this production supplies fuel for Basin Electric's Leland Olds generating station, a mine mouth power plant. The mine has 175 hourly and 50 salary employees. The Glenharold reserve extends over 210 square kilometers (80 square miles). The mining area is on a dissected plateau between the broad flat Missouri River flood plain to the north and the gently rolling uplands to the south. Erosion by intermittently flowing streams has produced many narrow, steep-walled, drainage ways. Mining begins at the 6 meter (20 foot) cover line and continues to the economic recovery line.

Jan 1, 1982

By Victoria Vaccarezza, Corby Anderson

The demand for rare earth elements for everyday technology and applications has initiated much research into the extraction and recovery of these rare earth elements. An otherwise unknown group of minerals, eudialyte is a zircon silicate consisting of rare earth oxides (REO), contained in a unique mineral structure and represented by a complex chemical formula. Research into extraction and recovery of rare earth elements involves various beneficiation and hydrometallurgical techniques. The goal of beneficiation being to efficiently liberate and upgrade the REO content, followed by hydrometallurgy to extract the desired elements. This overview will discuss previous research on treating eudialyte group minerals via different mineral processing and extraction techniques.

By A. D. Davis, G. A. Zabolotney

A ground-water flow model was developed to simulate the postmining recharge rate from precipitation at the Belle Ayr surface coal mine, which is located in the Powder River Basin near Gillette, WY Wyoming state regulations require that reclaimed lands should provide a rate of recharge that approximates the premining rate. Steady-state calibration and transient simulations showed that the postmining recharge rate through spoil is at least 50 mm (2 in.) per year, exceeding the original infiltration rate of 4 mm (0.16 in.) per year to shallow overburden aquifers. Major reasons for the increase include the flat topography of the reclaimed areas and the decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate that is less than 50 mm (2 in.) per year but still somewhat greater than the premining rate.

Jan 1, 1997

By Jaeheon Lee, Jai‑Won Byeon, Junmo Ahn, Jun‑Jae Lee, Eun‑Woo Kim, Yoo‑Jin Kim, Jiajia Wu, Jae‑Yeon Kim

Growing demand for valuable battery materials and environmental issues from battery disposal make the recycling of spent lithium-ion batteries (LIBs) essential. Specifically, the green approaches using organic reagents have garnered many attentions for battery recycling. In this study, a synergetic organic leaching system using methanesulfonic acid (MSA) of strong organic acid and citric acid (CA) with good chelating ability was investigated to extract valuable metals from LiCoO2. Hydrogen peroxide was used as a reducing agent to enhance leaching kinetics. Cobalt extraction of 98% and lithium extraction of 97 % were achieved in the optimized condition; 2.4M MSA, 1.6M CA, 1.0 vol% H2O2, S/L ratio 80 g/L, 85 °C, and 1 h. The optimal leaching condition of the MSA-CA mixed leaching system exhibited good applicability to various cathode scraps, such as LiCoO2, LiNixMnyCo1- x-yO2, and LiNixCoyO2. The dissolved Co and Li ions in the MSA-CA leachate were selectively recovered with high recovery efficiencies of 99 % and 97 % as Co3O4 and Li3PO4, respectively. The recovered Co3O4 and Li3PO4 were utilized to regenerate cathode materials. LiCoO2 and LiFePO4 were also synthesized through a solid-state reaction and hydrothermal method. The recycling process based on the MSA-CA-H2O2 synergetic leaching system was proposed, and it might be applied as a green and economical organic leaching system for the recycling of various types of spent LIBs.

Sep 20, 2023

By L. K. Marshall

Last month's engineering fundamentals article discussed some general considerations of underground mine ventilation. This month's article takes a look at auxiliary ventilation-brattice, fans, and ducting-in underground mines. The need for good, efficient auxiliary ventilation increases as mines get deeper and move farther from ventilation shafts. New mining methods and equipment resulted in faster work area advances, liberating more dust, gas, and heat. As a result, worker health and safety requirements in the face area have become more stringent. For all these reasons the safety and efficiency of any underground mine depends heavily on its auxiliary ventilation. The purpose of such ventilation is to supply sufficient quantities of clean air to the face of the drift and to maintain air quality within desired limits until expelled from the mine.

Jan 2, 1982

By Wayne Green

The Regional Municipality of York, located north of the City of Toronto in Ontario, Canada, has experienced unprecedented growth during the past decade, with new home construction averaging 15,000 units per year. This rate of growth is planned to continue well into the future with a projected growth of more than 500,000 new residents by 2031, combined with a tar-get of more than 300,000 new jobs to provide a sustainable economic base for the region. It should be noted that York region has been designated as one of the key growth centers by the province of Ontario, aimed in part to meet the housing and employment needs of Canada?s growing population. York Region is a mix of urban and rural areas and is one of the most desirable areas to live in Southern Ontario. York region offers an attractive lifestyle, with its nine municipalities and the amenities created by the many rivers, streams and protected greenbelt areas that encompass more than 69 per cent of the region?s area.

Jan 1, 2010

By Bates H. Murphy

There is one quick way to substantially reduce the operating cost of a great many pining operations. It is to cut the demand charge on the use of electricity and gas. Demand charge is the utility company's charge for the maximum rate of energy usage which is in addition to the charge for the total amount of energy used. Energy demand is reduced by prohibiting simultaneous operation of devices, especially those that consume large amounts of energy, or by deferring the use of such equipment as air conditioners from one demand period to a subsequent period. To achieve that end, a control system can continuously measure the demand and turn off selected loads in accordance with established rules. Because of the complexity of most industrial plants, a computer is the best means of storing, measuring, calculating, and controlling the many variables associated with the many devices involved. A computer system for that use has been developed by the Westinghouse Computer and Instrumentation Division in Orlando, Florida. For most applications, this demand control system can be installed and operated by industrial plant engineering personnel with no special knowledge of computer technology. It can be used with both electrical and gas service. For clarity, let us examine electrical demand first.

Jan 1, 1974

By A. Mei, F. Amadini, F. Cernera, D. Baliani, A. Flor, M. La Morgia, F. Sassi

The risk of TBM jamming because of squeezing rock mass or excessive caving (instability of the cavity) conditions is always a focal point while boring long and deep tunnels with shielded TBMs. Mechanized excavation provides a large amount of real-time data, for each machine’s parameters. Several analyses have been executed to assess the correlations between different sets of TBM parameters for the exploratory tunnel. Instead of analyzing the full dataset, a different approach is proposed, with data processed sequentially to simulate the real excavation situation. The probability distributions are recalculated together with their statistical parameters while advancing. This approach is extended also to the training of a Machine Learning model able to foresee the behavior at future rings based on past rings (using a Recurrent Neural Network). The predictions show a promising first step toward creating practical tools that can assist contractors and designers to correlate and predict TBM excavation data. These tools will assist to predict and quantify high risk situations that could arise during excavation.

Jun 13, 2023