Search Documents

By L. R. Chirinos

The Tintaya mine of BHP Copper, located in Southern Peru, includes a copper oxide deposit hosted in a mineralized skarn zone. The ore contains large amounts of clays and high acid consuming species resulting in low heap leaching performance. A treatment scheme was proposed that included a wet screening separation. The coarse fraction would be treated by heap and the fines by agitation leaching. The dissolved copper would then be recovered through solvent extraction and electrowinning (SXEW). Testwork determined the optimum heap leaching conditions to treat the oxide in on/off pads of 3 meter height with an initial acid cure followed by variable acid strength during irrigation. The method resulted in a reduced acid consumption and good copper recoveries.

Jan 1, 1997

By Bo R. Arvidson

The strongest magnetic roll separator available on the market enhances certain industrial minerals purity to levels not reached previously. Exceptionally strong forces can also be utilized for processing relatively fine particles at feed rates several times greater than for prior art electromagnetic induced roll separators. Since the unique machine does not work with an air-gap, coarser particles than what has been considered practical can be separated at rates up to 20 tph per single machine unit and 40 tph for a double machine unit. Examples for all these three application areas will be given. While the roll separator can be used only for dry processing presently, the other new separator can be used for both wet and dry applications. It is a medium-intensity, high- gradient magnetic separator employing a filamentary matrix. It was primarily developed for recovery of weakly magnetic iron ore fines, but it is finding applications for cleaning of industrial minerals such as wollastonite, calcite, clay and talc. Its main advantage is a simple design resulting in a very lm cost machine both with regards to total capital investment and operation. A significant technical advantage exists also. The metallurgical performance is similar to conventional electromagnetic separators, while the cost per ton is about half of such separators.

Jan 1, 1985

By R. Owens, C. Roos, B. Hill, S. Rosenthal

It is common practice, and even legally required in many jurisdictions, to design two-lane haul roads in open pit mines to three and a half times the widest dimension of the haul trucks operating on the road. In open pit gold mines with high strip ratios, the road width has a significant impact on the economics of a design. It is possible to minimize the flattening of the highwall if the road width is reduced, assuming the width used is not needed to flatten the slopes for geotechnical purposes. With the use of autonomous haulage and pullouts, it may be possible to operate safely and efficiently on a reduced road width of two times the width of the hauling equipment.

Mar 2, 2022

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008, “I guess that without the occasional complaint, your mine is probably over-ventilated” (Marks, 2008). Miners are seldom in this situation and spend much of the time trying to find enough air to keep an operation running. With examination, there are usually changes that can be made to increase the efficiency of ventilation systems. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Modifications that result in surplus mine ventilation air could bring financial and environmental benefits. Some issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and nonmetal mines, to ventilate reserves that are deeper, hotter, and further away from fans and shafts, and to meet demands from increased production. This paper discusses successful methods to find additional usable air when there is no extra ventilation capacity. Most of the options presented in this paper are useful for metal/ nonmetal operations but some may be applicable to coal as well.

Jan 1, 2009

By Simon Strong, Tim Brown, Luis Ignacio Sanz Vivanco

"One of the most significant technical and practical challenges facing the tunnel construction team on the Legacy Way road tunnel project in Brisbane, Australia was how to erect the pre-stressed precast concrete slabs to form the smoke duct in the tunnel boring machine (TBM) tunnels. An essential part of the tunnel ventilation system, the smoke duct, extends the full length of the 4.6km long twin, two lane tunnels. The vast majority of the tunnels (approx. 4.3km) were constructed using two 12.4m diameter double shield TBMs. The refurbished Herrenknecht machines broke several world records on the way to completing the tunnel excavation works in just over nine months. With the excavation complete the focus turned to solving the complex civil tunnel fit out challenges. A key component of the civil fit out of the tunnels was constructing the smoke duct in the TBM tunnels which was designed as a precast solution. The slabs which each measure 8.62m long by 2.0m wide by 200mm thick and weigh close to 9 tonne need to be erected above cast in situ corbels whilst other tunnel finishing works continue. The space proofing clearance offered by the design to the support corbels below and the precast segmental lining above was in the order of only 100mm. This paper details the events of how the Transcity JV tunnel fit out team, comprising some of Europe and Australia’s leading tunnel construction specialists, drew upon the global strengths of the existing JV member companies and the global reach of leading TBM manufacturer Herrenknecht to develop an innovative system to solve this challenging problem. This globetrotting story, which starts in Australia, visits Europe and mainland China before returning to Brisbane where it all began."

Jan 1, 2016

MINExpo International is billed as the largest exposition for the mining and mineral processing industry. And the 2012 edition, scheduled for Sept. 24-26 in Las Vegas, NV, is no exception. Put on by the National Mining Association (NMA), attendance at this year?s show is expected to be significantly more than the 38,500 who attended the last MINExpo in 2008. The exhibit will also be quite a bit larger in 2012 than it was at the previous MINExpo. More than 1,800 companies, representing more than 30 countries, will fill the Las Vegas Convention Center. The more than 850,000 sq ft of exhibit space will include the North and Central halls as well as South Halls Nos. 3 and 4. And the Silver Lot outside of the front door, under construction in 2008, will be filled with more exhibitors. The 2008 show attracted about 1,220 exhibitors occupying more than 600,000 sq ft of exhibit space.

Jan 1, 2012

By Arthur W. Ruff

The iron-ore beneficiation and shiploading facilities of the Marcona Mining Company are at San Nicolas Bay which is on the Peruvian coastal desert about two hundred and seventy miles south of Lima. The mines are at elevation of 2,500 ft. Crude ore is transported from the Mine primary crushers to the beneficiation plants by ten miles of overland belt conveyors. After the predominantly magnetic ore is reduced to minus 3/4 in. in the secondary crushing plant, the ore is ground by rod and ball mills and concentrated with magnetic separators. The concentrate slurry is pumped to a thickening and filtering installation for desliming and dewatering. Pelletizing is accomplished with a Lurgi and also a Dravo-Lurgi machine. Deep-water shiploading facilities are available close to the beneficiation plants. Figure 1 shows a flowsheet of the general operation. Pelletizing operations are scheduled 24 hours a day and 365 days per year. A maximum tonnage rate with a high percentage of operating time is necessary to produce the three and one half million tons per year required from the two pellet lines. Process control is a major responsibility and of primary concern to all Operating personnel. The particle size, moisture, and chemical composition of the filter cake must be closely controlled to get uniform high-grade pellets. Key points are sampled routinely and analyzed on a two-hour basis to provide the necessary structure and chemical data to maintain a superior final product. The iron content of the pellets is held between 65.3 and 65.8 percent with 4.0 percent Si02. Sulfur is below 0.04 percent and copper is below 0.02 percent in the finished pellet.

Jan 1, 1968

By Yuting Xue, Xin Li, Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Mindi Ruan

Most coal mine roofs in the Appalachian region consist of laminated shale, which is prone to brittle failure. Accurate modeling of shale roofs is vital for studying cutter failures of these shale roofs, and ordinary and formational bedding planes play a significant role in the response off the shale roof to mining-induced stresses. This paper presents a robust method for constructing three-dimensional shale roof models using limited borehole cores and leveraging image processing techniques. The approach begins with image extraction from shale cores. Then, we extract the portions that feature the core and employ image-stitching techniques to merge them seamlessly. Once the images are stitched, they are duplicated horizontally and merged to create a cross-sectional plane image representing a shale roof. This roof cross-sectional plane image serves as an input to our proprietary Digital Image Processing (DIP) algorithm, which is adept at extracting ordinary bedding planes (interfaces that represent color transitions between a single shale unit). The extraction process involves transforming discrete core points (ordinary bedding plane pixels) into continuous lines representing ordinary bedding planes. Finally, extending this method into the third dimension, the model is further extrapolated to form a comprehensive three-dimensional shale roof. Through this process, the geometry information of ordinary bedding planes can be extracted for each type of shale in cores, including sandy shale, gray shale, dark shale, etc. This work bridges the gap between limited core data and comprehensive 3D geological modeling, offering valuable insights into identifying and quantifying the variations in different shale roof geologies.

Jun 25, 2024

By Cary Hirner, Dan Lopez, Ross Webb, Stephen O’Connell

"Construction of the largest desalinization plant in the Americas has commenced in northern Chile. It is part of a several billion dollar expansion at a copper mine whose operations nearly stopped due to the challenge of securing a reliable source of water from the Pacific Ocean in a safe and environmentally sound manner. This paper discusses the risk management, design and construction of a quadruple chamber intake and outfall shaft, high capacity pump station, three 7m diameter vertically drilled marine shafts and three subsea tunnels constructed through challenging Andean hard-rock geology. The three 2.5m diameter subsea microtunnels are being mined with vertical curves through variable quality rock 30 meters beneath the ocean and retrieved in the wet from the 7m diameter marine shafts. INTRODUCTION AND BACKGROUND The battle for securing the rights to a constant water supply is a worldwide issue and nowhere is that more evident than the Atacama Desert of Chile, the world’s driest place with areas of the desert that have not seen rainfall in recorded history. The Atacama Desert also happens to be home to some of the world’s largest ore deposits which require huge amounts of water to extract and process. What available water there is comes from three main sources: deep seated wells, glacial water from the Andes Mountains, and desalinated water. Vying for water from wells and glacial streams and lakes are numerous agricultural and domestic facilities in the valleys surrounding the Atacama Desert. Environmental regulations and legal rulings have limited the amount of “natural” source water which can be used for mining purposes. Desalination plants are a known solution for combating water scarcity, albeit a costly one. The total estimated cost of constructing this desalination plant is over $3B USD, which will include a 2500lps capacity and an approximately 118km pipeline from the coast up to the mine located in the Andes. The overall scope of the project includes design, procurement, and construction packages for the 2500lps desalination plant including the seawater reverse osmosis plant, water conveyance to the mine, power transmission, the reservoir and the marine works package which forms the basis of this paper. Key components of the underground construction portion of the Marine Works are:"

Jan 1, 2016

By R. Robertson

Dense medium cyclones are the preferred means for cleaning 112 in. x 14 Mesh to 28 Mesh (12.7 mm x 1.0 mm to 0.6 mm) raw coal and are becoming a common choice for cleaning raw coal from a nominal top size of 2-1/2 in. to 3 in. (63.5 mm to 76.2 mm) down to 14 Mesh to 28 Mesh (1.0 mm to 0.6 mm). During the last ten years, dense medium cyclone circuitry design has undergone changes which have combined to improve process efficiency. This paper describes these improvements and compares present day design with the design used prior to the mid 1980's. Improvements in the following areas are described: Raw coal desliming, cyclone configuration, drain and rinse applications, dilute medium circuitry, and instrumentation and control.

Jan 1, 1997

By K. Perry, R. Eades

"Highwall miners continue to be implemented by operations to increase recovery, improve margins, and justify higher stripping ratios as high quality surface reserves become increasingly rare. Many times, operations facilitate projected underground operations by leaving an intact highwall for development purposes. These facts result in larger highwalls that are left standing for increased periods of time prior to reclamation. As a consequence, worker exposure and risk is also elevated, resulting in higher potential for accidents or fatalities relating to surface highwalls. Highwall stability is a complex issue, dependent on both geologic and mining factors. Dynamic numerical modeling offers the capability to assess possible stability issues related to blasting-induced ground vibrations. Research has been conducted to evaluate the effect of highwall stability due to ground vibrations from blasting events. Additionally, the relationship of amplitude and frequency, and their impact on highwall stability is investigated. The results of this modeling indicate that amplitude has little impact on stability. However, frequency has a significant impact on highwall stability. INTRODUCTION The number of mining fatalities has declined since 2010, and 2016 is currently on pace to continue this trend (MSHA 2016). This decline can be directly correlated to the decline in surface mining activity and the overall decline of the coal industry. However, since 2002 the percentage of surface coal mine fatalities associated with highwall activities remains relatively high, constituting approximately 15% of all surface mine fatalities. 2014 was the first year with a highwall failure fatality since 2011. Most recent surface coal mining fatalities are associated with machinery and haulage. Table 1 provides a summary of the total surface coal mining fatalities, and the number of highwall failure fatalities dating back to 2010.Highwall stability is a complex issue, dependent upon geology and geologic discontinuities within the rock mass, along with highwall geometry, standing time, and applied stresses. Another possible concern that has not been previously investigated is the effect of blasting-induced stresses on highwall stability and the stability of web/barrier pillar systems as a result of ground vibrations from blasting events. Many modern surface coal mines employ numerous extraction fronts that rely on blasting for primary rock breakage. This results in highwall and highwall pillar systems experiencing blasting-induced stresses of many different types and magnitudes."

Jan 1, 2017

By R. L. Lewis

The White Pine Mine is the second largest active underground copper mine in the United States, covering an area of approximately 34 km2 in the Upper Peninsula of Michigan. A numerical flow model of the White Pine Mine was constructed to evaluate engineering controls that would reduce the rate of mine water discharge after closure. Of the passive controls evaluated, the placement of low-flow bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35 percent.

Jan 1, 1996

By M. J. Sanzotti

This paper examines the potential for controlling longwall-induced subsidence by pneumatically backstowing the void created by mining with waste rock, and having the process scheduled as a unit operation of the mining activity. Based on a review of background literature, interviews with representatives of various mining companies, public-interest groups, and state and federal regulatory agencies, a hypothetical case-study evaluation of pneumatic stowing in a southwestern Pennsylvania mine site was conducted. The study indicated that current stowing technology cannot keep pace with the production potential of U.S. longwall systems. Further, at the case-study mine site, concomitant stowing would reduce subsidence by only 50% of that incurred during full longwall caving, the longwall coal production rate would decrease from 4000 tons per shift in the non-stowing case to 1500 tons in the stowing case, and a preliminary cost analysis reveals that pneumatic stowing would add $5.25 to $10.50 to the operating cost of producing a ton of coal at the case-study site.

Jan 1, 1995

The Boliden Aitik concentrator in Sweden processes 2,000 tph of low grade copper ore. The plant consists of five grinding lines feeding four bulk flotation banks with a scavenger concentrate regrind mill, and a column cleaner circuit with a regrind mill. The authors installed a model-based expert, optimizing control system to maximize copper recovery in the bulk flotation circuit while maintaining an appropriate copper grade in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent addition rates. It combines the power of a dynamic population balance model which estimates mineral liberation in each stream, an optimizer which computes appropriate set points and a rule-based module which implements the strategy. The benefits have been evaluated over three months. The model-based expert, optimizing control system generates a measurable increase in copper recovery, around 0.5 per cent and an optimized bulk concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 1998

By Jessica M. Wempen

"Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has application for monitoring subsidence with high resolution over short periods. DInSAR uses radar images to measure centimeter-level surface displacements. In the images, ground resolution can be relatively high, with each data point (pixel) representing the average displacement over an area of several square meters. The image data are acquired regularly which allows subsidence to be monitored sequentially over short periods; imaging periods typically range from weeks to months.Monitoring subsidence over short periods with high spatial resolution has potential to provide insight into the dynamics of subsidence and into relationships between mine advance and subsidence. In this study, for three longwall mines in the western United States, initial subsidence occurring at the start of longwall advance is quantified over short periods (12 to 72 days). C-band interferometric wide swath Synthetic Aperture Radar (SAR) images from the Sentinel satellites are used to quantify the subsidence. Overall, the data show initial development of subsidence, expansion of the subsidence trough, and the advance of subsidence in the direction of mining.INTRODUCTIONApplied Differential Interferometric Synthetic Aperture Radar (DInSAR)Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique that can be used to quantify small displacements of the Earth’s surface. Using data from the Seasat satellite, which was launched in 1978 (Jet Propulsion Laboratory, 2018), studies by Goldstein, Zebker, and Werner (1988) and by Gabriel, Goldstein, and Zebker (1989) applied Synthetic Aperture Radar (SAR) interferometry to topographic mapping and displacement monitoring. These studies established the potential for broader applications of radar interferometry. Studies by Foxall, Sweeney, and Walter (1998), Wright and Stow (1999), and Carnec and Delacourt (2000) represent some of the earliest evaluations of DInSAR for mine subsidence monitoring. All three of the studies demonstrated the application of DInSAR for quantifying mine subsidence. They also demonstrated difficulty accurately measuring subsidence over long periods due to data decorrelation. DInSAR continues to be evaluated as a tool to quantify surface deformation related to active and historic mining. For example, see Vervoort and Declercq (2018), Wempen and McCarter (2017a), Chen et al. (2013), and Liu et al. (2013). Technologies associated with SAR interferometry continue to develop. Recently launched satellites have relatively high spatial and temporal resolutions, and data processing methods and data accessibility are improving."

Jan 1, 2019

By D. K. Mynear, J. S. Gardner, S. Mittle, A. A. Campoli

West Virginia, although having adequate solar insolation, has witnessed very little actual solar development to date. The reasons for this lack of development are varied, but the primary obstacles to future development appear to be the absence of state-level policies and regulations promoting growth in the solar industry. West Virginia possesses large tracts of under-utilized land throughout the state created by previous mountaintop mining operations that could theoretically be re-purposed for solar farm development. Accomplishing this task will require not only revisions to the current legislation, but also acceptance by utility companies, landowners, and mining companies. Solar developers will need confidence that they can secure revenue from the electricity and Renewable Energy Certificates (RECs) generated by solar projects. Additionally, solar companies will need assurance they will be protected from any non-related environmental liabilities that could arise in the future. The primary avenue in bringing significant solar development to West Virginia will come through large corporate clients demanding or partnering with utility companies for incorporation of solar options into their energy portfolio to help meet established sustainability goals. This scenario has been witnessed in other states where a large client demands renewable options. Solar development could also represent a means through which mine operators might alleviate some of their reclamation and bonding obligations; where the landowner could supplement income from their underutilized land holdings; and where displaced miners could be repurposed in solar installation/maintenance jobs. Utilizing data from the West Virginia Permit Database, this report identifies several mine sites that hold potential for solar development in the future. INTRODUCTION The diversification of energy sources in the United States (US) has seen major shifts during the past decade resulting from: • A sudden abundance of low-cost natural gas becoming available through advanced horizontal drilling and hydraulic fracturing techniques. • Incentive-driven policies leading to new development in alternative energy. • The emergence of renewable energy sources, proliferated by state and federal level incentives and falling capital costs. Coal was once the primary low-cost fuel source for the generation of electricity in the US for most of the last century, providing approximately 50 percent of the total production capacity. However, within the past decade lower-cost natural gas has overtaken coal as the primary source of fuel used in electricity generation, and renewable sources have steadily grown to account for approximately 10 percent of the overall mix.

Jan 1, 2019

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015

By R. C. Milici

The primary factors that determine the marketability of coal from various supply centers in the U.S. are coal quality and supply; i.e. low sulfur, moderate- to high- Btu coals have large market areas when compared to less expensive but poorer quality coals. Price is the major factor in the competitive marketing of similar coal products. Good quality, (moderate- to high- Btu, low sulfur) coals from the Powder River and central Appalachian basins are marketed over large areas of the country, and central Appalachian coal is widely distributed in foreign markets, primarily as coking coal. In contrast, poorer quality bituminous coal (low calorific value and/or high sulfur) from the Illinois Basin, northern Appalachian Basin, and lignite from the Gulf Coast is marketed in or near the States in which it was mined even though the price at the mines may be lower than mine prices for central Appalachian coal. Widespread distribution of sub-bituminous Powder River Basin coal is enhanced by its exceptionally low mining costs, which offsets transportation costs to distant markets.

Jan 1, 2001

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By Bryan Ulrich

Knight Piésold and Co. hosted its annual roundtable discussion on March 17, 2011 at the Stockman Hotel and Casino in Elko, NV. The theme for Roundtable 2011 was, ?High density tailings, paste, and filtered tailings,? although the topic may well have been subtitled, ?Don?t prematurely rule out any technologies before they are given their day in court.? Bryan Ulrich, Knight Piésold?s local representative, as well as Tom Kerr from Knight Piésold?s office in Denver, CO, were on hand to help facilitate the discussion. Ulrich and Kerr are senior vice president and president of Knight Piésold?s U.S. practice, respectively. The event played host to more than 30 attendees from several western states. Attendees included personnel from a dozen mining properties and various corporate offices. There were also attendees from manufacturing and specialist consulting firms who have been providing services to various high-density tailings, paste and filtered tailings operations worldwide. It may be noted that the term ?filtered tailings? is used in this discussion. Alternative terms, such as ?dry stack? or ?dewatered tailings,? should be avoided whenever possible, as such terms tend to give a false sense about the nature of the material since these materials typically still retain a significant amount of moisture.

Jan 1, 2011