Search Documents

By R. J. Kolada

The ventilation systems of coal storage silos are normally capable of rapidly dispersing any accumulations of methane in the atmosphere above the coal pile surface. However, the results of an investigation which is presented in this report show that hazardous concentrations of methane can accumulate within the coal pile. Methane trapped within the coal pile is released into the atmosphere of the loading gallery when coal is discharged from a silo. If the methane released is of a flammable concentration it is necessary to ventilate the gallery to reduce the risk of an ignition. This report proposes a simple test, which, after further investigations may prove to be an effective method to calculate gallery ventilation requirements.

Jan 1, 1985

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By Dayu Long, Changhong Li, Yu Wang, Juzhou Li, Yongyue Hu

To address the problem of seepage failure that affects the stability of the fine-grained tailings dam, two kinds of prevention and treatment measures were proposed involving composite flocculants and composite curing agents. The orthogonal test was conducted to determine the optimal ratio flocculant (ORF) and the optimal ratio curing agent (ORCG). Then, numerical models were established to evaluate the effects of the prevention and treatment measures on the seepage and stability of the tailings dam. The results show that the mechanical properties and microstructure of the tailings are significantly improved by adding the ORF and ORCG. Furthermore, numerical studies suggest that the addition of the ORF and the ORCG to the tailings improves the factor of safety of the tailings dam, but the addition of the ORCG also increases the height of the phreatic line. It is also speculated that the addition of the ORF can prevent the formation of through failure zone in the tailings dam. Therefore, the optimal measure to prevent seepage failure in the tailings dam is adding an appropriate amount of the ORF, as it reduces the height of the dam’s phreatic line and lowers the risk of seepage failure. The typical area susceptible to seepage failure can be treated by adding the ORCG. However, it is important to ensure adequate drainage of the area and to maintain the phreatic line at a reasonable buried depth.

Mar 4, 2024

By T. L. Myron

To determine the effect of flux crystal size on the production rate and strength of sinter, batch sintering tests were conducted on samples of both dolomite and limestone of various crystal sizes. In addition, calcination tests .were performed on the dolomite and Limestone to determine the effect of crystal size on calcination rate at various temperatures normally attained in sinter beds. The results indicate that flux crystal size does not affect sinter production rate or sinter strength.

Jan 1, 1962

By R. Larry Grayson

A survey of 1250 surface and underground coal mines across the United States was made according to a stratified sampling technique based on national coal districts. A total of 171 responses (13.7% response rate) have been returned and summarized, giving a picture of computer usage in the coal industry. Overall, 63.5% of the respondents use computers, but the percent varied from 100% for large mines to only 44.1% for small mines. As expected, a proliferation of microcomputers has pervaded the industry. Importantly, in spite of the high usage of computers in the industry, sophisticated engineering applications have not yet burgeoned.

Jan 1, 1989

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles) northeast of Winnemucca, Nevada. The deposit is owned by First Miss Gold Inc. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 m (1 400 ft.) to 671 m (2 200 ft.), along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate within the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By Terry L. Muldoon

On July 7, 1971, noise regulations for underground coal mines were implemented under provisions set forth in the Federal Coal Mine Health and Safety Act of 1969. These same regulations now also apply to coal mine surface facilities. In August 1971, in anticipation of these regulations, the Bureau of Mines, through the cooperation of the mine operators, conducted extensive noise surveys in three coal cleaning plants. The survey was conducted in an attempt to identify those occupations where exposures would exceed the proposed regulations.

Jan 1, 1972

By R. L. Loofbourow

The Sunro Copper Mine is near the south coast of Vancouver Island about 35 miles west of Victoria. Failure of the roof of a large open stope let a good sized mountain stream into the mine. Broken are, boulders and sand were washed into the underground mill and out through a 7 800-foot adit. The adit became plugged; water burst out an a ridge above the adit, washing out the portal and o trestle by which it was reached, Rock and ore are strong but several systems of steep, pronounced but generally tight fractures are found on and parallel to the walls of the orebody. The stope was started from a slusher drift 390 feet below the bed of the River and brought up to an elevation 155 feet below the River by blasting vertical and horizontal rings of longholes in the nearly vertical orebody. Mining was stopped there and five months were given to grouting and bolting the pillar under the bed of the River, During this time and for several months thereafter sloughing increased the width, length and height of the stope. At the last known observation the stope was 77 to 96 feet wide, 185 feet long and the highest point of the domed back was only 55 feet below the River. The flooding took no lives. In other respects, however, it might be difficult to find in mining lore o more savage example of the application of "Murphy's Laws".

Jan 1, 1968

By N. Wahl, D. M. Blackketter, R. Thornton

This paper evaluated using a water-filled abandoned mine (Orphan Boy) as a heat source for a 240- kW closed-loop heat pump with the goal of heating a 2,000-m2 building. The mine has a 245-m vertical shaft connected to a large stope by three horizontal cross-cut shafts. There is 1,250 x 106 L of water at a consistent temperature of 24-26° C that is available mostly in the stope. The only heat exchanger placement option is in the vertical shaft. Therefore, the focus was to model heat exchanger placement in the vertical shaft to determine the extent to which the systems will induce thermal currents between the stope and vertical shaft. Modeling of thermal currents, temperature profiles and heat contribution from the ground was done using finite difference and computational fluid dynamics. An optimal configuration was determined showing sufficient water movement and heat transfer will occur with a low water temperature in the shaft above 20° C. This project supports a U.S. Department of Energy (DOE) grant that will implement the full-scale system.

Jan 1, 2013

By Chee Theng

"Mining professionals are a resilient lot. Sure, copper prices are dismal, permitting processes seem interminable and the top mining companies are shedding jobs like a Shetland sheepdog sheds hair. All the more reason to hone technical skills, reconnect with old contacts and get one’s finger on the pulse of the industry.More than 400 did just that in the balmy sunshine and among the saguaro cactus of the Tucson venue of the SME Arizona Conference.Giving the keynote speech was Patrick Merrin, vice president at Hudbay Minerals (see box), while the luncheon speaker was University Distinguished Professor Mary Poulton, director of the Lowell Institute for Mineral Resources at The University of Arizona.“Attendance was great, especially given the copper price,” said Ta Li, vice president of business development at Tetra Tech and 2001 SME President. “The luncheon speaker was one of the better ones in recent years. Her talk contained a lot of fresh ideas, and practical versus theoretical concepts.”Talk about values, not economicsPraise was unanimous for Poulton, who gave a thought-provoking talk on “The New Face of Mining: The Culture Change for Compatible Mining.” Corporate social responsibility has been embraced by the metals mining industry, and it’s being done right, she said. “So why do we have more conflict? Why are there more protests? Why does permitting take longer and longer?” Poulton made a case for an approach based on compatible, rather than sustainable, mining to present a new face of mining that can be compatible with communities, cultures and the environment, and still be profitable. When the mining industry starts to talk about compatibility between what it is doing and what “me,” as the consumer, wants, what “we,” as citizens of a community, want, and what’s good for the “world,” we’re going to see the next culture change happen, she concluded."

Jan 1, 2015

By Robert H. Scott

Developments during the past few years have brought coal-based composite fuels to commercial readiness. During the next few years, composite fuels will become available from a number of suppliers. Potential users must evaluate the combustion properties of these fuels to determine equipment and operating changes required for their use. Most work to date has been done with boiler applications. However, many potential non-boiler applications exist in the metals and minerals industry. These applications require specific evaluations appropriate for the processes involved.

Jan 1, 1982

By Jim Huerta

Diesel fuel usage in the mining industry continues to escalate. This is because approximately 60 percent of all mined materials are surface extracted by large equipment using diesel fuel, which continues to increase in cost per gallon. For example, coal mining uses large equipment such as wheel loaders, wheel dozers, draglines and [ ] dredgers. In one year, three of the largest U.S. coal mining operations consumed approximately 567 million to 852 million L (150 million to 225 million gal) of diesel. At an approximate cost average of $3.25/gal the expenditure on diesel is $487 million to $731 million per year. So, are there any solutions that could reduce this cost burden? Yes, there are. Coal mining companies can extract less ore; use more efficient extracting equipment that consumes less fuel; wait for a significant reduction in the cost of fuel; or find and use technology that would create efficiencies that would lower the cost. Nanotechnology is one such technology that might provide the means to create the efficiencies that will significantly lower diesel fuel costs.

Jan 1, 2011

"From April 22 to 28, the eyes of the tunneling and underground construction world will be on San Francisco, CA, as the world’s most influential underground construction industry leaders gather at the Moscone Center for the 2016 World Tunnel Congress.Recognized as the most important international annual meeting for the industry, the 2016 version comes to the United States for the first time in 20 years and will be hosted by the Underground Construction Association of SME (UCA of SME). The conference will be held in lieu of the UCA’s biennial North American Tunneling Conference and will bring the strengths and resources of the UCA of SME and the International Tunnelling and Underground Space Association (ITA). The result will be a conference with unmatched technical programming and a showcase of more than 200 exhibiting companies.A program committee led by Randy Essex of Mott MacDonald, Lonnie Jacobs of Frontier Kemper Constructors, Michael Mooney, of the Colorado School of Mines, Priscilla Nelson, of the Colorado School of Mines and Amanda Elioff of Parsons Brinkerhoff formed the program committee and worked for more than two years to build the program. The result is four technical sessions with five tracks in each session and 185 oral presentations.“One challenge was the sheer size of the group that would be assembled, perhaps 2,500 attendees or more, and the large number of abstracts we were likely to receive,” said Essex. “ We investigated extending the conference a fourth day, but that was not workable with the Moscone Center. We settled on having five concurrent technical tracks – something that has not been attempted in past NAT or RETC conferences to my knowledge. The next step was to develop suggested session titles that would span the breadth of subjects that would interest conference attendees as well as serve the conference theme.”"

Apr 1, 2016

By P. A. Korpi

In March of 1978 the first set of Angular Spiral Liners utilized in grate discharge ball mills for wet grinding was put into service in the San Flanuel Concentrator of Flagma Copper Company. The use of these liners has decreased grinding media consumption by 19.2% and grinding energy consumption by 15.8%. In addition a 1.1% increase in grinding throughput is being realized through the use of the system. This paper describes the Angular Spiral Lining System and reviews the test program at the San Manuel Arizona Concentrator. Operating parameters are discussed in addition to the current testing program to futher optimize the system.

Jan 1, 1982

By G. A. Gruber

A flotation process has been developed to successfully treat ore from the Santo Domingo phosphate deposit in Baja California Sur. The ore contained less than four percent P205 with quartz, silicates, and carbonates as gangue minerals. Flotation of the low grade feed In sea water required that the conventioinal Crago Process, comprising direct anionic flotation, deolling, and inverse cationic flotation be augmented by an anionic cleaner flotation step, phosphate depression, and a calcite flotation step.

Jan 1, 1986

By J. V. Bymark

It is the intent of this paper to discuss the autogenous grinding circuit at Hibbing Taconite. The scope of the presentation includes; a brief history, the process flowsheet and the steps taken to improve mill productivity, availability and metallurgical performance. Hibbing Taconite is located near the center of the Mesabi Range in Northern Minnesota 100 miles from the Canadian border and 80 miles north of the Lake Superior Port Cities of Duluth and Superior. A 105 mile railroad connects us with the port of Superior, Wisconsin, where our pellets are loaded into lake carriers for lower lake destinations. It is worthy to mention the Mesabi Range's most famous landmark which is immediately to the south of our mine area. This is the Hull Rust Mahoning Mine which operated until the mid-1970's producing more than 700 million tons of red ore between 1893 and 1973.

Jan 1, 1985

By J. W. Rinard

This paper is intended to introduce "non engineers" to one of the more misunderstood pump performance parameters, NPSH (Net Positive Suction Head). This basic presentation and resultant review should provide a practical understanding of NPSH and what its importance is to pump operation and reliability.

Jan 1, 1996

By R. D. Hagni, P. A. Shivdasan

Cathodoluminescence microscopy (CLM) is uniquely applicable to the study of carbonatite-related fluorspar ore deposits. The mineralogy of the carbonatites, sodic and potassic fenites, marbles, quartzites, and fluorite ores are readily determined and characterized. Calcite, dolomite, apatite, fluorite were deposited dominantly under high temperature conditions and they exhibit strong cathodoluminescence (CL). Three types of carbonatites have been recognized at the Okorusu, Namibia carbonatite complex and fluorspar mines by field mapping and laboratory CLM. The main carbonatite intrusion is fine grained and consists mainly of calcite. A later phase of pegmatitic carbonatite consists of calcite, magnetite, Fe-rich pyroxene, apatite, and pyrochlore. Pyroxene carbonatites were recognized mainly through their study by CLM.

Jan 1, 2001

By Ingemar Marklund

INTRODUCTION Today at LKAB, the primary mining method used is sublevel caving, independent of ore-body size, shape, dip, and geographical location. The mining of small ore bodies with relatively flat dip involves a lot of develop¬ment work, a large initial investment, big dilution, and large ore losses. In 1975 serious investigations into other possible methods, especially for those small ore bodies which do not lie in direct contact with other ore bodies, began. Different methods were studied and a number of in¬teresting ideas came from Russian mines. An analysis was made of one of the proposed methods, sublevel benching, in which mining is carried out from raises, and which uses the throw from the blast to place the broken ore. However, there were reservations about working in big open rooms at great depth, and doubts about the possibility of getting acceptable drilling results in an acceptable environment from raised platforms. Testing was therefore delayed for a time. However the investigations continued and in the fall of 1976, it was decided to try vein mining in a small ore body (Indian) (see Figs. 1 and 2). MINING RESULTS The results are now available from the mining of Indian and are as follows: Ore plan area 1200 m2 Level height 50 m Ore volume 60 000 m3 Ore tonnage 270 000 t Iron content 62% Dip 0.69 rad (40°) Ore thickness 14 m Ore compressive strength 26 MPa Ore C-factor (fracture density) 0.21 Hanging wall compressive strength 28 MPa Hanging wall C-factor 0.27 About 40 000 m of the holes were drilled by ring drills with an average productivity of 85 m/shift; loading of a round (2 rows, 750 m of hole) was usually accomplished in one shift. The total ore recovery was about 270 000 t with an average iron content of 59%, and three to four shifts were required per round (4700 t) to load. The principal of "throwing" the rock during blast¬ing worked well, and no ore remains on the footwall. ROCK CONTROL Before mining commenced at Indian, it was dis¬covered that the rock strength in its vicinity was rela¬tively poor. Since the ore is flatly dipping, and mining was to take place with open rooms, the strength of the hanging wall was of great importance. A supplementary program of exploration drilling was done during the fall of 1976 in order to assess fracture spacing and rock strength from the drill cores. Results showed that the strength of the hanging wall was low because of the many fractures. A decision was made to try cable bolting of the hanging wall by extending some of the ordinary blast¬holes. Cables (20 mm diam) were grouted in these larger holes and the rest of the hole was then utilized for ordinary loading (see Fig. 2). About 100 bolts altogether were installed and, to date, only small falls have occurred and the hanging wall is holding. Its exposed area is 2100 m2 DEVELOPMENT WORK On the 350-m level, four crosscuts (two per mining room), one longitudinal drift, and two elongated drifts (one per raise) for the raise climber were developed as shown in Fig. 1. Of the 230 m of drift, 60 m were in ore and the rest in waste. For mining room A alone, a total of 115 m of drift were needed with 30 m in ore. The drift dimensions were about 4.5 X 5.5 m. In the drifting on the 300-m level, two connecting drifts were driven from one existing transport drift forward to the respective raises. The total development was 93 m, all in waste (Fig. 1). The two raises having a length of 80 m each were driven at an angle of 0.68 rad (39°) from the hori¬zontal. They were driven along the footwall contact with a separation of 30 m and had an area of 10 m2. LONG-HOLE DRILLING The drilling of long holes with the ring drilling unit began in the fall of 1977 in raise A. The equipment consisted of an Alimak raise climber, equipped with a lower platform from which the charging was done.

Jan 1, 1982

By T. R. Raponi, D. Barnes

The Williams Mine mines and mills 6000 t/d (6600 stp’d) of gold ore using SAG/ball milling, leaching and CIP, electrowinning and refining. Electrowinning, high-pressure cathode washing, filtering, retorting and refining are based around the use of knitted stainless steel mesh cathodes. Their primary advantage over conventional steel wool cathodes is that electrowon gold can be washed off and the cathode can then be reused. Typically, the knitted cathodes have a useful life of up to 15 months. Gold production of up to15 t/month (50,000 oz/month) is easily processed with this system. Presented is a description of this operation, including a review of the equipment and performance data.

Jan 1, 1992