Search Documents

By M. Argiantopoulou

In today?s mining environment, improving production, performance, productivity and profitability is crucial. Production, ancillary, plant and shipping equipment need to be monitored and controlled by online systems delivering production statistics and real-time information to everyone involved, including equipment operators. Traditional systems currently in use today, operate in an iterative mode constantly switching between scheduling and execution. However, the real world tends to change in ways that invalidate such advance schedules. Agent based computing has been hailed as the most significant breakthrough in software development and the new revolution in software. Agent systems are being used in an increasingly wide variety of applications, including complex mission critical systems such as Air Traffic Control. This paper presents the possible ways that multi-agent systems can be applied to mine production and rehabilitation scheduling problems with focus on real time fleet management, plant and equipment performance monitoring, downtime and delay reporting, stockpile management, personnel and equipment tracking and product distribution and transportation.

Jan 1, 2006

By D. L. Kuck

Water ice pillars far underground mine roof support can be frozen and/or maintained and/or melted on demand. The system to do this consists of a refrigeration brine chiller, brine circulation system and disposable plastic containers. Fusion expansion, resilience to dynamic loads, plastic deformation under stress, and non-contamination of coal or ore are unique properties of ice. Lower labor and material costs are economic advantages of ice far mine structural support. Ice brattices can become ice pillars on retreat. For safety, ice pillars can be placed (by remote control, if necessary) in hazardous sites without human entry.

Jan 1, 1988

By Bryan C. Smith, Duane R. Skidmore

Volumetric mass transfer coefficients and gas holdups were measured in a concentric tube airlift reactor designed for the microbial desulfurization of coal. The slurries were comprised of an acidified basal salts solution containing thirteen different weight percents of coal (74 µm Ohio #1) at three temperatures. An enhancement in the mass transfer coefficient, KLa, with respect to that measured in pure solution was found at weight percents of 5 (volume fraction solids, ES = 0.035) or less, the greatest enhancement being as great as 37% at approximately 2 weight percent (ES = J 0.014). At higher solids fractions, the mass transfer coefficient decreased with further solids additions, decreasing by as much as 91% at 40 weight percent coal (ES = 0.315). KLa increased with temperature at all solids concentrations, the greatest increase being 392% at 72°C vs that measured at 30°C. Gas holdup, EG decreased with all increases in solids loading by as much as 65% and increased by as much as 67% with temperature. KLa and EG were correlated with operating conditions separately, and the separate correlations combined to yield overall correlations for the mass transfer coefficient and for the gas holdup. The correlations are suitable for inclusion in system models devised earlier for microbial coal desulfurization processes, and may be used for design, operation and cost estimation for such systems.

Jan 1, 1989

By I. Koliabina

In this paper, the results of mathematical modeling of casing pipes decontamination from radio-active new mineral forms directly in boreholes using hydrochloric and hydro-silicic-fluoric acids are presented. Modeling for highly and low radioactive coatings on the walls of casing pipes of Anastasievka oil-and-gas deposit was performed using GEMS software, based on the method of Gibbs energy minimization. Calculations have shown that thorianite and goethite, that are present in low-active crusts, detected in casing pipes uplifted from comparatively low depths, are well dissolved in hydrochloric acid, but radiobarite is almost insoluble. For the same acid concentrations, almost all radiobarite of high-active coatings detected in pipes uplifted from considerable depth is dissolved. To evaluate the possibility of decontamination of pipes from radiobarite of low-active coatings, modeling of crust dissolution under the action of H2SiF6 has been performed. The results have shown that for acid concentrations of more than 13 % almost all Ra and Ba are dissolved while all iron and thorium remains in goethite-thorianite solid solution. For the same acid concentration, almost all radiobarite from high-active coatings is dissolved. Therefore, no reagent allows decontamination of pipes from coatings of both types. It seems that successive or simultaneous use of both reagents (HCl and H2SiF6) in certain ratio is required. To clarify this issue, further experimental and model investigations are necessary. The issue of decontamination of casing pipes from galena that is present in high-active crusts also needs to be clarified.

Jan 1, 2005

By K. Kohli

A case study involving a historic structure undermined by longwall mining is presented in this paper. The location of this study is in South Western-Pennsylvania; USA. The structure is 150-years old and subsided 4.5 feet. This paper discusses the mitigation measures taken to reduce the subsidence damage and its effectiveness.

Jan 1, 2002

By Howard W. Earnest

The Rio Blanco Oil Shale Company completed a modified in situ oil shale retorting demonstration at its Tract C-a Lease in the Piceance Creek Basin of northwestern Colorado during the spring of 1982. This demonstration was the first MIS project with shafts rather than adits for access to the mining operation, and it involved several potential hazards which required that particular attention be paid to mine ventilation. Methane was first encountered during shaft sinking and ultimately resulted in the mine being classified gassy by MSHA. Secondly, we encountered hydrogen sulfide in association with the ground water, and this proved to be a more persistent problem than did the methane. Thirdly, in order to burn the underground retorts, it was necessary to provide for potential leakage of retort gases and to obtain a modification to the MSHA standard which forbids fires under- ground. This modification had a significant effect on the ultimate ventilation procedures at Tract C-a. An extensive under- ground air monitoring program was included in the ventilation system.

Jan 1, 1983

By Joseph Clare, Elizabeth Anderson, Mike McGinley, Ron Hines, Judy Cochran

The South Lake Union Pipelines contract for King County Wastewater Treatment Division and Seattle Public Utilities in Seattle, Washington included three 1.8 m (72-in)inside diameter microtunneled pipeline segments totaling about 793 m (2,600 lf).Tunnel alignments were within street right-of-way of heavily traveled urban roadways. Project challenges recognized in the design included: high groundwater levels; contaminated soil and groundwater; variable soil conditions, including fill; and timber piles and other obstructions remaining from historic land uses. The tunnels were built using a Lovat MTS Microtunneling machine, beginning in spring 2003. Conditions encountered during construction presented additional challenges beyond those anticipated in the design process, and were successfully addressed by the owners, designer, and construction management consultant all working with the contractor. Problems included highly variable soil conditions, cracking of reinforced concrete pipe joints during pipe jacking, a timber pile trestle uncovered during shaft construction, and obstructions encountered in the second and third microtunnel runs.

Jan 1, 2005

By Ronald L. Wiegel

The United States produces approximately 40 mil- lion tons of phosphate rock per year. Most of this rock is converted to diammonium phosphate and used as a fertilizer component for the domestic and international agricultural market. Much of this phosphate rock production is concentrated in the southeastern United States, with about half coming from washing and screening operations and half from flotation separation from sand and clay. This paper summarizes current operating practice in the industry and touches on some of the emerging technologies required to solve the problems associated with a diminishing high- grade reserve and the need to implement dolomite/francolite separations on a commercial scale.

Jan 1, 1999

By A. K. Bakshi, K. J. Shoop, Komar S. Kawatra, T. C. Eisele

Slurry rheology can have significant impact on the performance of autogenous grinding circuits. A viscous slurry can act as a cushion and retard impact forces between the media and the ore, which reduces grinding efficiency. On the other hand, a dilute slurry will not be viscous enough to hold slurry in the impact zone of the media, which will lead to inefficient use of impact energy. An unfavorable rheology can also lead to overgrinding or centrifuging of the slurry inside the mill. Slurry rheology also affect classification, with higher viscosity increasing the cut size. In this article, the causes of the rheological effects on autogenous grinding and hydrocyclone classification have been discussed. Both plant and pilot scale data from autogenous grinding have been provided to show the effects of viscosity on specific energy con- sumption and other breakage characteristics of the ore. It is shown that: (1) high viscosity, produced by low temperature and high fines content, significantly increases the specific energy consumption and the production of critical size material in an autogenous mill; (2) In hydrocyclone operation, increasing the viscosity causes the d50(c) size to become coarser.

Jan 1, 1998

By Stephen R. Hunt

This paper summarizes some preliminary results of the Illinois State Geological Surveys current investigation into surface subsidence resulting from coal mining in Illinois. The purpose of the study is to characterize-the vertical movements that may result from various types of underground coal mining. In general there is relatively little published information about subsidence from room-and-pillar mining as compared with longwall mining. The findings of this study, based on mining operations in a variety of geologic settings, delineate the magnitude, shape, and position of the subsidence profile. Comparisons of case histories of subsidence are based primarily on the extraction ratio and the general geometry of the mine (depth, panel width, and mining height).

Jan 1, 1979

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide) are situated in Arkansas. Less concentrated brines (about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in Arkansas and Michigan. Arkansas, with its six plants, was the leading U.S. state in bromine production. Bromine being the leading mineral commodity valuewise produced in the state. The Michigan bromine production was a byproduct of magnesium compounds production.

Jan 1, 2006

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

The generation of microscopic bubbles by cavitation may enhance particle-bubble attachment and improve flotation performance. It is shown in this paper that tiny bubbles or cavities can be generated by strong shear and turbulence in high speed liquid flows. These conditions create the necessary pressure fluctuations in the bulk water to cause the local pressure to drop below a critical value. The formation of bubbles is favored by high dissolved gas contents to promote gas diffusion into the cavities, and by the presence of surfactants to provide some mechanical strength due to the adsorbed film. Experimental results on bubble formation by cavitation and consequent flotation of fine silica (d50 = 1.6 µm) are presented.

Jan 1, 1995

By S. C. Lamey, P. A. Hesbach

This study evaluated the use of regionally produced coal combustion products to neutralize and remove metals from acid mine drainage (AMD). Synthetic AMD mixtures were treated with a number of fly ashes and fluidized bed combustion (FBC) ashes. All of the ashes reduced the volume of the sludge produced and gave a faster settling rate than the sludge produced by treatment with lime. Faster settling allows greater throughput rates. In addition, the FBC ashes, which generally contain alkaline components used for sulfur capture, completely neutralized the acidity and, if desired, raised the pH above 10. The fly ashes, on the other hand, reduced the final volume of sludge but required additional neutralizing agents to attain a pH >5. The pH of the AMD can be taken to above 10 to insure complete removal of manganese, or it can be taken to a more neutral pH of 7 or 8 to allow for the safe introduction of the aqueous phase into ponds or streams. The process combines two industrial waste products to reduce the disposal volume of one of the waste products and to produce an environmentally safe aqueous discharge.

Jan 1, 2002

By G. T. Adel

The application of automatic control to mineral processing operations has been gaining momentum during recent years. Many strategies are being developed for controlling crushing, grinding and flotation circuits, however, their implementation in industrial plants is being slowed down because of the costs and difficulties in evaluating these strategies in a systematic manner. An interactive computer simulation package, developed at the University of California, provides the capability of analyzing the process dynamics of mineral processing circuits. This paper presents an overview of the simulator and its application to the case studies of grinding and flotation.

Jan 1, 1983

By Gerald L. Dollinger

INTRODUCTION Today more tunnels are being bored by mechanical means in igneuus and metemorphic rocks (i.e. "hard" rocks) than ever before, and there is reason to believe that this trend will continue in the future. Because of this, there is an increasing demand fur stronger, more powerful machines and fur cutters that are capable of handling the high loads and abrasive rock conditions that often accompany hard rock tunneling. Tunnel boring machines ("TM's") built today, therefure, generally have higher thrust and torque capabilities than those built in the past, and they are equipped with the largest cutters and rings now available. The recent experience in hard rock tunneling has demunstrated that TBMs can be both efficient and ecunumical under such conditions, and that acceptable performance rates can be achieved in all but the hardest rock. In spite of this success, it is believed that improvements in buth the cost of boring and in performance rates can still be made through mudificatiuns in the existing kerf cutting system. Some impruvements in TBM performance under hard rock conditions, fur example, have already been made thruugh the development of constant section rings that maintain a constant edge width and, therefore, a constant level of performance as they wear. The recent experience in hard rock tunneling has also produced a wealth of new TBM performance data through the systematic study

Jan 1, 1983

By PATRICK R. TAYLOR, NICHOLAS BELLUSCI, D. ERIK SPILLER, VICTOR BRAMAN

Most of the world’s production of natural soda ash comes from the mining and processing of trona found near Green River, WY. The processing of trona ores to ultimately yield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale, is water and energy intensive. It is speculated, however, that the glass-manufacturing industry, which is the largest consumer of soda ash, may be able to use product of a lower grade and consistent level of the insoluble constituents. Thus, the viability of using sensor-based sorting to produce a beneficiated trona stream that would be fed to calcination was investigated. The study encompassed the preparation of a run-of-mine (ROM) Green River ore sample; selection of specimens sized 25 to 75 mm; imaging of the specimens by sensors based on X-ray transmission (XRT), color and laser-induced fluorescence (LIF); insolubles analysis of the specimens; and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content exists, and that a surface-detection-based sensor, particularly LIF, is apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65 percent separation efficiency and a 70 percent recovery of trona could be achieved.

Feb 1, 2023

By C. G. Tester

Automatic tripper control systems can be reliable and as such are suitable for use in the mining industry. Proper application of fundamental engineering principles provides the means for the reliability. Some of the principles are: (1) Be sure the system designer designs a system that does the job operations people want done; (2) Use sound logic design practices to avoid internal electrical problems; (3) The design must be maintenance oriented; and (4) Use good quality components. I would like to discuss a tripper control installation at Kennecott Copper Corporation, Chino Mines Division, in Hurley, New Mexico, and how these principles apply to this tripper control system. First, however, I will expand on the principles to clarify just what is meant. First, "Be sure the system designer designs a system that does the job operations people want done.? Operator acceptance is often the key to the success or failure of an automatic control system. One of the best ways I know of to get operator acceptance is to give him a system that he wants. I don't mean to imply that if bad practices or procedures exist that they should be incorporated in the control system. I do think that many designers feel they haven't done their job if the control system doesn't do things drastically different than the old manual method. Good engineering principles dictate that the job should be done right and if the manual method was right it can very likely be right for the automatic method.

Jan 1, 1973

By Kewal K. Kohli, Thomas Z. Jones

This paper presents a simplified computerized method for the prediction of maximum subsidence and the subsidence profile for the Appalachian Coal Basin using the Hyperbolic Function Profile Method. Several case histories are cited to demonstrate the appropriateness of the predictive method. In addition, sample runs and a detailed listing of the computer program is provided. Other popular subsidence prediction methods are discussed and compared with the Hyperbolic Function Profile Method.

Jan 1, 1986

By Roland Froidevaux

The potential use of geostatistics for quantitative ore reserve reporting is shown using a simple gold case study as an example. The need of defining quantitative class limits is stressed, and a possible approach to this problem is suggested.

Jan 1, 1983

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009