Search Documents

By D. Babich, L. Alcorn, E. Spencer, A. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for Fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% [Gigliotti et al. 1991]. In order to properly determine workers’ exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop guidelines and test procedures for identifying all noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. Once the high noise sources are identified, promising engineering controls can be tested and evaluated to reduce the noise of the sources. The measurement system used to analyze the noise sources included stationary dosimeters in a documented repeatable pattern and a time-motion study of the cutting cycle and operator’s work cycle. Significant results from the underground measurements show that the highest sound levels recorded are at the stageloader discharge segment and tailpiece controls and remained at about the same level throughout the test.

Jan 1, 2007

By Kang-Hyun Kim, Ho-Jong Kim, Jong-Ho Shin, Hoon-Ki Moon

"In urban areas, it is often required to construct additional railway tunnels beneath existing railway tunnels. In this case, dynamic interaction between tunnels at the intersection becomes an important issue, as it amplifies structural behavior causing damage to structures and inconvenience to passengers. In this study, vibration superposition effect at the intersection between existing and newly constructed tunnels is investigated by the numerical method. Dynamic interaction mechanism is firstly examined using simple sine wave load, and then a typical analysis for actual multi-leveled tunnel intersection is performed. The results show that the dynamic amplification due to dynamic interaction of tunnels is 149% at the crown of lower tunnel. This indicates that the vibration superposition effect must be considered when the planning and design of a new tunnel beneath the existing tunnel. 1. INTRODUCTION In these days, there are increasing cases that trains cross without transfer stations in metropolitan areas. Consequently, either tunnel is necessarily to be neighboring or crossing, thus tunnel sections closely located are created as shown in Figure 1. If a new tunnel is constructed beneath the existing tunnel, the vibration due to trains passing through each tunnel can mutually affect. The behavior of coupled vibrations may occur and exceed the allowable structural limit, and cause inconvenience to passengers. Theoretically, when vibration waves are propagated from a source to different locations, amplification or decrease of the vibrations can occur by the principle of wave superposition and interference. Multi-leveled tunnel intersection is one of the cases mentioned above. In the actual tunnel, it is difficult to investigate the vibration superposition effect due to a complex ground conditions and structural geometries. In addition, train vibration itself is multi-source vibration, which cannot be theatrically analyzed. Thus, at the tunnel intersection, train vibration from two tunnels make the problem more complicated."

Jan 1, 2016

By Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths (from 500 feet to 1000 feet) and six different diameters (from 14 feet to 24 feet) were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1977

By Alissa Lockett, Chris D. Breeds

Central Water Integration Project (CWIP) Segment 5-1 is the most critical segment of a regional water supply project that transfers groundwater from Burleson County to northern San Antonio, replacing over 20% of that City’s water supply with a new source. CWIP Segment 5-1 included three tunnel reaches totaling 10,350-ft and 5 shafts that were constructed inside the City in an area known to contain large karst features. This paper describes site work used to investigate the alignment for karst features, manage potential environmental impacts, develop the contract package required for mitigation and the means and methods used to mitigate the large karst features that were encountered.

Dec 1, 2022

By R. Merkl

Since the 1940s, decanter centrifuges have become more important for increasingly complex solid-liquid or solid-liquid-liquid separation processes. Sometimes processed industrial or metalliferous minerals are abrasive or are treated with corrosive chemical agents. Traditional mining applications include the processing of coal, gravel and other products, where low-speed decanters, as well as screen bowl decanters and filters, dominate. These have been increasingly replaced by high-speed decanters during the last decade. Decanter centrifuges also started to play a key role in applications such as drilling muds, processing carbonates and separating SX crud in copper platinum ore concentrations of nickel and gold. Communication between machine producers and mineral processing engineers is vital for the right choice of materials and the design of the right decanter centrifuge for the individual process.

Feb 1, 2012

By L. Yuan, J. H. Rowland

"In 1995 and 2003, the U.S. Mine Safety and Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) that were being used in underground coal mines in the United States. The survey reports gave data for the different AMS manufacturers, the different types of equipment monitored, and the different types of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along belt haulage entries. As of Dec. 31, 2009, point-type heat sensors are prohibited for use for an early fire detection system. Instead, carbon monoxide (CO) sensors are now required. This report presents results from a new survey and examines how the regulation changes have had an impact on the use of CO sensors in underground coal mines in the United States. The locations and parameters monitored by AMS and CO systems are also discussed.IntroductionThe last survey conducted by the U.S. Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems used in underground coal mines in the United States was in 2003 (Francart, 2005). A total of 146 active mines were surveyed. The survey report states that since 1995 there had been a steady increase in the use of atmospheric monitoring systems in underground coal mines as the technology of carbon monoxide (CO) sensors was improved by manufacturers. Atmospheric monitoring systems had become more reliable, and some CO sensors could be purchased with the capability to discriminate between the CO produced by a fire versus CO produced by diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed miners to take the necessary action to put out the fire or exit the mine.At the time of the last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than when using point-type heat sensors (Conti and Litton, 1995)."

Jan 2, 2018

By A. Mukherjee

This paper presents an analytical technique for prediction of the damaged rock zone (DRZ) around a circular drift subjected to an anisotropic stress field (analytical solution exists only for the case of hydrostatic stress field). The method can readily be adapted to micro or personal computers. Stress concentrations around the drift are calculated at the centers of small rock elements, using the analytical solutions for a hole in an infinite plate. Potential failure of a rock element is assumed to be governed by the Coulomb failure criterion. When the failure condition is exceeded for an element, the excess shear stress is transferred to the neighboring elements. Progressive failure is allowed to occur until convergence is obtained. The final configuration of the damaged rock zone so obtained can be used to assess rock support requirements, as well as modified modulus and permeability of the DRZ.

Jan 1, 1988

By Elza Burch

Introduction The feeding to zero concept involves feeding 600 µm x 0 (28 mesh x 0) size raw coal to heavy media (magnetite) cyclones along with the +600 µm (+28 mesh) size coal. Traditional circuits employ desliming or removing the 600 µm x 0 (28 mesh x 0) size fraction and feeding the cyclones +600 µm (+28 mesh) size coal. The feeding to zero concept recirculates 600 µm x 0 (28 mesh x 0) fines in the circuit. At the same time, a portion of the fine material is continuously withdrawn and recovered. This, in turn, prevents a fines buildup. This concept eliminates desliming screens and secondary fines circuitry for recovery of 600 x 150 µm (28 mesh x 100 mesh) coal. The result is a very simple circuit. Feeding to zero at Island Creek Island Creek Corp. was the first involved with the new concept in 1976. The company needed a temporary plant for the 9.5 mm x 0 (0.4 in. x 0) raw coal at its Pond Fork mine, near Madison, WV, while a full-scale plant was being designed and built. At that time, the Childress Corp., of Beckley, WV, became interested in the feeding to zero concept. Island Creek awarded a contract to Childress to build a single cyclone modular plant, incorporating this feeding to zero concept. The plant was erected in three months. The Pond Fork modular plant proved successful in attaining the desired feed rate of about 63.5 t/h (70 stph), while maintaining good separating efficiencies and low magnetite consumption rates. The 9.5 mm x 150 µm (0.4 in. x 100 mesh) clean coal was recovered and the 150 µm x 0 (100 mesh x 0) size was disposed of to waste. The full-scale plant was completed about two years later and the Pond Fork modular plant was moved to Holden, WV. There, it was incorporated into the Holden 29 preparation plant as a separate circuit for cleaning -25 mm (-1 in.) coal. In 1976, a similar plant was installed in Virginia by another company. These two plants are believed to be the first two operational plants in the United States incorporating the feeding to zero concept. Island Creek subsequently contracted with Childress for an identical plant at the Coal Mountain operation in West Virginia. The plant operated for three years before the mine was closed. The unit was then moved to the Spurlock mine near Martin, KY where it continues to operate. The successful operation of the Pond Fork and Coal Mountain plants before and after relocation proved both the performance and moveability of this type of circuit when constructed in a modular fashion. Since the first two plants were built, Island Creek has incorporated the feeding to zero circuit in nine additional plants. A grand total of 33 cyclones have been installed using this concept. One is the Providence mine, near Providence. Providence preparation plant Island Creek contracted with J.O. Lively Corp. of Glen White, WV in July 1978 for the construction of the Providence preparation plant. The plant began operation in February 1979. The construction period was about halved by building the plant with modular design concepts. Prefabricated sections, floors, and sides were brought in as units and then bolted in place. The Providence plant has a good track record of processing coal at a feed rate of 454 kt/h (500 stph). Feed coal to the plant has an average ash content of about 18% and sulfur content of about 4.5%. It contains about 22% refuse. The coal product has an average ash content of about 8% and sulfur content is about 3%. Raw West Kentucky No. 9 seam coal is conveyed from a box cut in the Providence mine to a rotary breaker. The breaker is fitted with 74 mm-diam (3 in.-diam) opening breaker plates. Therefore, it is well suited for removing trash, roof bolts, wood, and pyritic balls that are common in Illinois Basin coal. The -75 mm (-3 in.) coal is conveyed from the rotary breaker to

Jan 8, 1987

By W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and trucks at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between the shovel and trucks with the new truck cycle times.

Jan 1, 1968

Terminology. The term potash originated in "pot ashes" produced by burning wood to ashes in iron pots and then leaching out the soluble salts, chiefly potassium carbonate, from the residue. In modern usage potash is a generic term for various potassium salts used in agriculture and industry. More specifically, it denotes the oxide of potassium, K2O, and the content of potassium in ores and products is stated as weight percent of K2O present. Its salts are commonly referred to as muriate of potash, sulfate of potash, etc. The presence of an adequate supply of available potassium in the soil promotes the health and improves the quality of the plant. insures greater efficiency in photosynthesis, increases resistance to certain diseases, offsets the effect of an oversupply of nitrogen, and helps the plant to utilize soil moisture more advantageously. ("Soils and Men," U.S. Dept. of Agriculture Yearbook 1938.) Occurrence. Potassium ranks seventh among the elements in abundance. It is estimated to constitute some 2.6% of the lithosphere and is found in soluble forms in the oceans, lakes, rivers, and subsurface waters. It is also an important constituent of plant and animal life. Commercially significant accumulations of potassium salts occur in underground deposits formed in past geologic times by evaporation of ancient bodies of saltwater, inland drainage basins, and shallow sea lagoons. The potash content of such waters was the end result of weathering and leaching of insoluble potash-bearing aluminosilicates, such as feldspars, micas, leucitcs, and others. The concentrations of potassium salts in the natural brines of some lakes in the arid and semiarid regions of the continents are also important as sources of potash; the brines of the Dead Sea in Asia Minor, the Great Salt Lake in Utah, and Searles Lake in California typify such concentrations. Every continent has major potash deposits as listed in Table 1 adopted from Cawley.1

Jan 1, 1985

By J. D. Shenk

The White Cliffs diatomite deposit occurs in a lacustrine facies of the Quiburis Formation, an Upper Miocene to Pliocene basin-fill sediment of the lower San Pedro Valley. On-going geo-logic mapping has defined an 2.5-3.0 m (8-10 ft) thick ore zone near the mill site, several marker beds, a NNW-trending high-angle normal fault, and a NW-trending syncline. The diatomite has an average loose-weight dry bulk density of 130 kg/m3 (8 lbs/ft3) and is presently marketed outside Arizona for asphalt filler. Current development is projected to yield 3500 mt (4000 st) of finished product, with an estimated 91,000 mt (100,000 st) of finished product obtain-able from several other nearby sites.

Jan 1, 1988

By S. W. Swerson

25.1-THE PURCHASING FUNCTION The word "purchase" means "to obtain by paying money or its equivalent; to buy for a price." This definition is all too simple to properly describe the word "purchase." One should consider the basic objectives of purchasing-to procure the right material, of the right quality, in the right quantity, at the right time, from the right source at the right price. Here it should be noted that in purchasing it is recognized that the best quality or grade of materials may be the only grade to purchase for a specific job. However. there are other jobs where the medium, standard or poor grade of materials is the right quality, as the lesser grade will perform adequately. In some companies the purchasing department makes the decision as to the right quality, while in others this function is shared with other departments. Years ago in business the owners controlled the purchase of required materials and services by performing the task themselves. The owners obtained the type materials and services they needed and paid the price demanded. This function was performed along with all the other duties requisite to the owner of a business, namely, clerical, hiring and firing of personnel, financial management, etc. As companies grew in size, clerical duties were assigned to other personnel and the owner usually retained the purchasing authority. This same division exists today in many small companies. However, in the larger companies, the purchasing function has been assigned to a separate department. Importance of the Purchasing Function-The larger the company the greater the need for a separate department to perform the purchasing function. Today the purchasing agent for most larger progressive companies has policy-making authority. Therefore, it is reasonable for him to report to the president or vice president of his company. Studies of several hundred companies show the purchasing department head reporting to top management 87.5% of the time. This fact in itself is indicative of the importance of recognizing that effective purchasing requires a department staffed with specialists in the field of procurement with knowledge and experience sufficient to perform in today's complicated business atmosphere. In the manufacturing field it is a common axiom that usually half of the company's dollar expenditures are for materials. If a purchasing department functions properly and the right product or service is purchased and a savings accomplished, the contribution to the net profit of the company is much greater, as opposed to sale dollars, where only a small portion is carried forward to net profit. Thus, the importance of the purchasing department and the contribution it can make to the success of the company are obvious. 25.1.1-THE PURCHASING FUNCTION 1. Responsibilities of the Purchasing Function-The purchasing agent in performing his function is acting as an agent for the company and others in the company requiring materials and services. Accordingly, he is committing the company for materials and services subject to certain limitations which the board of directors may stipulate. In view of this, the purchasing agent,'^ position must of necessity he

Jan 1, 1973

By D. S. Bloswick

An investigation an4 analysis of slip/fall accidents specifically pertaining to underground coal mines was conducted. From a population of 751 accident reports, three major sources of injury which account for over 80% of the incidents have been identified. The specifics of this study are presented in this paper. Based on the results, several recommendations are made to reduce such accidents in underground mines. In addition, a brief discussion of the slip-hazard analysis laboratory at the University of Utah, which will be useful in future analyses of these accidents is presented. Work in this facility includes the simulation of certain mining activities in a controlled setting. Foot forces are measured and work methods subsequently developed to minimize the slip potential of these activities.

Jan 1, 1988

By Larry Powell

Rend Lake is an Army Corps of Engineers reservoir located in Franklin and Jefferson Counties in south-central Illinois. The lake consists of 20,000 acres of water and 19,000 acres of public access land. The site attracts over two million visitors a year and is surrounded by campgrounds and other recreational facilities. The lake overlies the largest tonnage of low sulfur coal in the state. Coal is being removed beneath the lake from five mines operated by three coal companies. Currently high extraction mining operations are approaching low-lying, environmentally sensitive, and high-use recreational areas. Advanced planning to maximize coal extraction and minimize potential effects of subsidence requires the development of procedures to assess the impact of high-extraction mining on the land use of the area. The Bureau of Mines, the Corps of Engineers, and the coal companies have initiated research to assess the following proposed planning steps to ensure the maximum recovery of the coal resources while minimizing impacts to surface land use: 1) Establish a dialogue between the surface and mineral owners; 2) develop a geographic information system to aid in assessing existing land use and potential changes; 3) assess the potential effects of subsidence on drainage, wildlife habitats, and changes in land use prior to mining; 4) coordinate the mining displacements with surface activities to minimize disruption; and 5) develop appropriate mitigation plans before mining occurs.

Jan 1, 1986

By D. A. Gulley, L. J. MacDonnell, William A. Vogely

INTRODUCTION Environmental impacts are most commonly associated with air and water pollution. Not- withstanding this fact, to many people the primary disruption caused by mineral extraction is the change in the character of the locale. That is, the environmental impact of mining includes, but is not limited to, the generation of residuals. The dramatic transformation of wilderness or rural land often creates strong reactions to mineral development. Thus, the basic issues of land use management are a useful addition to environmental discussion. In this section, we take up a discussion of federal, state, and local land use management regimes, along with a brief introduction to the potential role of economic analysis. Elsewhere in this volume, land management issues are discussed from other orientations, and the interested reader may wish to look there as well. Locatable Minerals on Federal Lands Legislation and Administration: Access to hard-rock minerals on the public lands is governed by the General Mining Law of 1872. This law declares that "valuable mineral deposits in land belonging to the United States . . . are hereby declared to be free and open to exploration and purchase . . . ." In order to initiate rights, prospectors are required to physically stake claims of specified sizes and shapes following basic procedures set by federal law which may be supplemented by the individual states. Rights to these claims are protected at the exploration stage so long as actual possession is maintained and diligent exploration activity is underway. If a valuable mineral deposit is discovered on the claim, the claimholder earns the exclusive right of possession as against private parties so long as the claim is properly maintained. To maintain this exclusive right the claimholder must per- form $100 worth of labor or improvements, known as assessment work, on each claim every year and make related annual filings with the U. S. Department of the Interior. If the existence of a valuable mineral deposit can be demonstrated, and other legal requirements are met, the claimholder may receive a patent giving full title to the claimed land, including the surface in most cases. The purchase price is either $2.50 or $5 .OO per acre. The Mining Law has remained largely un- changed by legislative amendment during its now more than 100-vear existence. However, while the law itself has not changed, its interpretation and administration have changed considerably. Written at a time of rapid western expansion of the U.S. following the Civil War, the intent of the law was to promote mineral development by inviting unrestricted prospecting and by selling the lands containing mineral deposits at a minimal charge. As federal land policy shifted from one of rapid disposal into private ownership to one of retention and management for a number of uses, mineral patenting requirements have been administered more strictly. The most critical issue concerns what must be demonstrated to establish the existence of a valuable mineral deposit. The so-called "prudent man" standard was established in the case of Castle v. Womble (19 L.D. 455 (1894)):

Jan 1, 1985

Tunnel damage from explosion and earthquake excitation is correlated with strain and particle motions. Critical strains and motions are then correlated with focal distance, which is so small that permanent strains are highly likely. The shaking process is then numerically modeled to investigate the effects of excitation frequency and joint orientation. The models confirm that near cavern blocks slide intermittently only at relatively high particle velocities during periods of low joint normal stress. Larger displacements occur with relatively small shear wave lengths or relatively high frequencies. Variation in joint orientation and rock mass dilation result in changes in displacement.

Jan 1, 1985

By ETHAN FUSTER, STEPHEN LEE, Richard Ray

By offering savings in space and capital cost compared to ducted axial and centrifugal fan systems, horizontally mounted jet fans are commonly used worldwide to ventilate vehicular tunnels. They discharge high-velocity jets to transfer momentum to the surrounding airstream to induce longitudinal flow in the same direction as the jet. Vertically mounted jet fans installed in exhaust shafts have been successfully used to ventilate a large passenger rail overbuild in New York City. A comparison of shaft dimensions, vertical placement of the jet fans and measured shaft airflows is presented to evaluate optimum jet fan configurations. Measured shaft airflows are compared to airflows predicted by computational fluid dynamics (CFD) simulations of a three-dimensional model of the overbuild.

Sep 1, 2022

By James K. Ballard

Leach dumps in Butte are relatively new in comparison with older established dumps in other areas throughout the West. With the exception of one 10 million ton dump, all dumps have been formed on a prepared base. This is necessary because the entire leach dump area overlies an alluvial fill which varies in depth from 100 to 400 feet and through which solution would be lost. Preparation of the leach pad consists of first removing all vegetative material and compacting the exposed surface with rollers. This surface is covered with a 4" layer of minus 1" crushed rock which in turn is roller compacted. A 3" compacted layer of asphalt hot mix is then applied to the crushed rock surface. Final sealing is effected by a 1/4'? coating of catalytically applied hot asphalt. Dump leaching was inaugurated in 1964. First solution applied was wholly made up of mine water pumped to surface through a central pump shaft. Sulfuric acid was added on surface at a surge pond to control pH of the leach solution. Acid addition is necessary not only to benefit the leach dumps, but to prevent the formation of ocher scale within the pipe line distribution system. Mine water pH is on the order of 2.8. The combination of ferrous and ferric iron as well as magnesium and aluminum salts is such that ocher forms at a pH of 2.38. It is therefore mandatory to control pH at 2.0. Dump effluent pH is held at 2.3 or less.

Jan 1, 1968

By G. R. Coonan

A number of famous studies have shown that house damage relates better to peak particle velocity than to acceleration or displacement. The relationship is true but doesn't go far enough. Why, for example, can construction shots go well above 1.0 or 2.0 inches per second without reportable damage? Recent studies have shown that vie must look at frequency and duration of an event in addition to amplitude. The complexity of measuring frequency, duration, and amplitude makes the average blaster in the field shudder. An even more excruciating problem is the need to obtain such data inside the building or residence in order to accurately predict the damage potential or human response to nearby blasting. The author reviews current research programs and suggests new areas of research necessary to help maintain a balance between complicated research requirements and simple field measurements.

Jan 1, 1980

By J. H. White

It is hypothesized that the Hotelling Valuation Principle (HVP) can determine the value of developed gold reserves using simple methods and easily obtained data. This paper reports the results of an empirical test of this hypothesis. Using publicly available data from North American gold companies, we obtained data for V, R, p, and c and ran a simple linear regression using equation (1.1) as the definition of the dependent and explanatory variables. By examining the value of the coefficients of the resulting regression equation, we can draw conclusion as to whether or not the HVP can be confident1y used as an estimator of the value of developed gold reserves.

Jan 1, 1995