Search Documents

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By Arpad E. Torma

The electrochemical behavior of a zinc sulfide concentrate during the microbiological leaching was investigated using ZnS-carbon paste electrodes and a cyclic voltametric technique. The effects of Zn2 [ ] , Fe2+, Fe3+ and Cu2+ on the cathodic and anodic currents associated with zinc sulfide leaching in presence and absence of microorganisms, were assessed. The semiconductor nature of zinc sulfide was discussed in terms of ability of microorganisms to obtain their metabolic energy (through removal of electrons) from this high energy gap substrate. The intermediate electrochemical reactions involved in the ZnS leaching were described.

Jan 1, 1989

By Jill Dill Pasteris

Several mineralogical prospecting techniques are used in diamond exploration. Most are concerned with identifying indicator minerals such as garnet and ilmenite, which are derived from mantle xenoliths hosted by kimberlites. The first goal of such prospecting is to locate kimberlite intrusions; the second goal is to identify the diamond-bearing kimberlites. Explorationists have worked much less on the indigenous kimberlite phases. The kimberlitic opaque oxides, ilmenite and particularly spinels, promise to be useful in discriminating between intrusion episodes in identified kimberlites, and perhaps in the evaluation and prediction of diamond grades. Several petrologists have showed that spinel compositions and zoning patterns are specific to certain intrusive facies in South African and Canadian kimberlites. Careful evaluation may indicate a correlation between spinel parameters and diamond content.

Jan 1, 1983

By Jürgen Brune

This is a shortened version of the paper ?The Methane-Air Explosion Hazard Within Coal Mine Gobs published in the 2013 volume of SME Transactions (Brune, 2013, pp. 376-390). This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Evidence from numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners, including the explosion of the Upper Big Branch Mine in West Virginia, where 29 miners lost their lives April 5, 2010.The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions, along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe. Keywords: Longwall, gob, methane, EGZ, explosive gas zones, underground, coal, explosion, fire

Feb 1, 2014

By R. A. Wharton, Z. Yang, R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al(III) and flotation collectors. It was found that the presence of Al(III) is necessary for good flotation of the organism, whether or not Pb(II) is present, when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8, and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al(III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminopropionic acid is used as collector, good flotation occurs at about pH 4 without the addition of Al(III).

Jan 1, 1992

By I. H. Gundiler

Although cyanidation has been universally applied in the processing of gold and silver ores, the search for less toxic alternatives continues. Difficulties encountered in processing ores containing oxidized copper minerals and the inherently slow kinetics of cyanidation have generated a renewed interest in thiosulfate leaching. This process, as well as the catalytic effects of copper ion, were well recognized and widely applied towards the end of the past century. In this study, the effects of copper, ammonia, and thiosulfate concentrations on gold dissolution were investigated using the rotating disk technique. Extraction of gold and silver from an oxidized copper-bearing ore was also studied utilizing a statistical experimental design, and these results were displayed in the form of contour plots.

Jan 1, 1993

By M. I. Brittan

A technique has been developed that analyzes routine mill operating data to determine the key operating parameters responsible for gold losses to tails. These parameters represent the prime operating variables having a dominant effect on gold recovery. The technique quantifies these effects for the specific plant being analyzed, providing a tool to optimize recovery and costs and so enhance the mine?s cash flow. The quantitative relationships generated will be different for each ore and plant: every case is site-specific and has to be treated on its merits. Examples are provided to illustrate the considerable metallurgical and financial benefits which can be realized from optimization. The examples are taken from case studies of mills in four major gold mining districts of the world.

Jan 1, 2010

By E. Krist

The newest addition to the Anamax Mining Company's Twin Buttes copper producing complex is a by-product uranium extraction plant which was placed into service in February 1980. The plant is unusual in that it is placed internal to the copper countercurrent decantation, solvent extraction, and electrowinning plant. The plant reached full production within a month and, to date, has produced continually above design rates.

Jan 1, 1981

By P. E. Nielsen, T. L. Loga, B. B. Mauko

A numerical model is presented which simulates the dynamic fracturing process for a circular geometry fracture in a uniform stress medium. The dependence of crack aperture and net pressure in the crack upon various dominant parameters of the fracturing process is discussed. An analysis of a 75% nitrogen foam fracture in a coal seam at 5600 feet (1707 m) is also presented. The analysis is based upon the discussed parametric trends, the job records of treatment parameters, and a Nolte plot of net downhole pressure. It is interpreted that fracturing with water, in pre-foam fracture pump tests, resulted in significant fracture height growth. However, the subsequent foam fracture had reduced height growth due to the high effective viscosity of the foam and due to the higher magnitudes of elastic modulus and stress in the bounding rock strata with respect to the coal.

Jan 1, 1986

By Ronald L. Wiegel

In a mineral processing plant there are a number of routine decisions which are based at least in part on the plant's metallurgical performance. Among these are those related to: 1) equipment functioning properly 2) suitable operating conditions 3) reagents achieving desired results 4} determining operating response to changes in ore 5) defining circuits offering potential for improvement A step beyond the routine, are the periodic management evaluations of operating supervision and technical assistance, which are based largely on profit -a direct function of are availability, metallurgical performance and operating costs. The "yardstick", excuse me -"meterstick", by which performance is best measured is the plant metallurgical balance, which tells not only what was produced but how it was produced. Since this metallurgical balance is directly related to both plant profits and individual rewards, it is only reasonable to make that "meterstick" as precise as humanly possible.

Jan 1, 1978

By Alok Garg, Rajeev Kumar Dayal

The Himalayan ranges have complex geological formation induced with locked up tectonic stresses and squeezing ground conditions. High overburden, steep slopes, perennial snow, and forest cover restricts accurate prediction of geological features, resulting in surprises during excavation. The tunnel planning under high altitude, extreme climatic, and unfavorable approachability conditions requires elaborate detailing. The construction technique and working faces for excavation are influenced by site accessibility/high overburden conditions, restricting the provision of access tunnel or shaft. The paper discusses site constraints influencing construction method and working faces for 8.9 km long highway tunnel at elevation 3,000 m under 1,900 mover burden through quartz-mica-schist formation.

Jan 1, 2001

By Roy Norcross, Stephen Gos

For over 100 years Degussa has worked together with the min­ing industry not only providing quality products but also develop­ing technologies to support these products through value added goods and services. For cyanide, these technologies include leach enhancement processes such as PAL™ and Solidox™, and cyanide detoxification with peroxygen based processes such as SILOX™ and Caro's acid using our DegOX™ technology. Degussa has also made important advances in how sodium cyanide is packaged and shipped with our liquid NaCN plant joint venture with MSI, CYANCO in Winnemucca, Nevada, and our Advantage SLS™ solid to liquid cyanide delivery system. All of these innovative technologies developed to support NaCN in mining, provide value to our customers and show Degussa's commitment to Responsible Care·11.1 and dedication to product stewardship. With Responsible Care and the customer in mind, Degussa has developed Advantage CCS™ cyanide control system, which will soon be available for the North American market. Currently there are several CCS units in service installed by Degussa AG (Germany), and we are in the process of designing the next gen­eration of the CCS which should be completed by late '98. Based on our experience working with gold and silver mines all over the world, there appeared to be an opportunity to further assist our customers by providing a better more automated way to control their cyanide additions. By providing the mine with an accurate method for maintaining their desired cyanide levels in their leach circuits, we could help them avoid underdosing and the associated gold and silver losses, and overdosing the cyanide which not only wastes cyanide but may increase treatment costs as well. In the early 1990's, when we began to introduce our CCS units, there were several cyanide controllers and on-line analyzers avail­able. However, they appeared to be too complicated and not made to stand the harsh conditions inside a mill. This resulted in exces­sive downtime and poor analytical results. We also found that many units would be installed but not commissioned by the sup­plier. Based on these observations, along with filtration and con­trol problems on some existing units, Degussa decided to design its own cyanide control system based on our extensive knowledge of cyanide chemistry, using the best components available worldwide.

Jan 1, 1998

By Gy. Deák Deák

The ECOMINING platform aims to develop a scientific and technical organization in order to promote within the natural resources industry a framework for environment-friendly exploitation technologies (on Best Available Technologies principle) and also to develop a solid basis for performing Research and Development projects. The ground of this project is the success of the First International Seminar: ECOMIN-ING - Europe in 21st Century1, organized by the Research and Development National Institute for Metals and Radioactive Resources Bucharest in co-operation with ITASCA Consultants GmbH Germany, the University of Petrosani and supported by the National Society of Salt Bucharest & Praid salt mine branch and the Ministry of Economy and Commerce. The platform provides a complex data base, for partners? selection and researchers? team structure. This can provide the scientific results with a high level of confidence for the projects of interest in the field of exploitation of mineral resources and for the participation on national and international project proposals competitions (i.e., target the 7th Framework Programme or any European / national programme, which can provide funds for the ECOMINING platform field of interest). The next step is the affiliation of the ECOMINING platform to the European ones, and to be compatible with them. The ECOMINING platform represents itself a 7th Framework Programme (FP) project idea.

Jan 1, 2007

By B. P. Sullivan

This paper describes how the author projected the economic benefits of a proposed coal liquefaction project based in Pennsylvania. These benefits were assessed in a successful effort to garner government support for the project. The projections considered such issues as increases in employment, wages, and tax receipts to state and local government, plus other less-obvious benefits, such as site remediation. The paper explains how sponsors of similar projects can use economic projections in making meaningful and compelling presentations to federal, state and local authorities.

Jan 1, 2000

By Rolland L. Blake

The Bureau of Mines is investigating the potential for in situ leach mining "(ISM) of gold and silver mineralization. This preliminary study examined samples from several types of deposits using light optical microscopy and the electron microprobe to characterize the ore and gangue minerals and their microscopic characteristics, including the spacial relations between the target minerals and likely natural fluid channelways. Low grade disseminated deposit types from the western U.S. were found to contain fracture-hosted or matrix-hosted gold and silver minerals, some of which are encapsulated by quartz or pyrite. Geologic features readily observed microscopically include ore and gangue mineral identity, size, and their association with each other and with fractures. Successful ISM application to gold and silver deposits needs this data to: (1) select the proper lixiviant based on chemical reactivity of the host rock, ore, and gangue minerals, (2) determine potential permeability characteristics when designing lixiviant flow patterns, and (3) understand potential problems of the lixiviant reaching encapsulated ore minerals. Careful examination of the geologic characteristics of each ore body is required because of the observed diversity of characteristics in deposits from the same "class" and even within the deposit itself.

Jan 1, 1989

By D. R. East

The concept of sub-aerial tailings deposit.ion using a managed rotational deposition system to form a deposit of partly-saturated tails for North American conditions was introduced by Knight and described by Knight and Haile (1983). The application of the sub-aerial technique, together with continuous removal of all surface waters and underdrainage outflows from the Key Lake uranium mine I s tailing storage facility in Northern Saskatchewan, Canada, has been documented by Knight and Haile (1984). Since then, the concept is being applied in the United States to tailings facilities in California, Nevada, Arizona, Utah, Colorado, Idaho and South Dakota.

Jan 1, 1989

By Christophe Bragard, Brett Robinson

This paper reflects the challenges encountered during the construction of the light rail tunnels under Boyle Heights, in Los Angeles, California. Equipped with two state-of-the-art EPB TBMs, the construction team undertook the mining of twin bored tunnels in the Los Angeles alluvium. The gassy underground conditions dictated many aspects of the design of the tunnels, as well as the tools and means used for their construction. This paper will detail the challenges encountered during construction, as well as the means, methods and logistics used on the project. Discussion includes: EPB TBM machines with some very unique/specific features; complex assembly sequence due to limited shaft access; final precast concrete liner with double gaskets; NATM cross passage excavation in soft ground and below the water table; compensation grouting; mucking shaft arrangement.

Jan 1, 2007

By Parris A. Lyew-Ayee

The Government or Jamaica has just completed agreements with four of the five bauxite/alumina companies operating in Jamaica. These companies are Kaiser, Reynolds, Alcoa, and Alcan, and the Agreements came into effect on February 1, 1980. One of the results of these new Agreements is the Acquisition of all company-owned bauxite lands by the Government and the rationalization of bauxite reserves.

Jan 1, 1980

By J. R. Dillon

Today more than ever, there is an increased demand for higher plant production capacities and efficiencies to offset the increasing costs for labor and materials. Plants involved in processing large volumes of bulk materials are particularly interested in more efficient material handling systems to (1) reduce labor and maintenance costs, (2) improve blending of non-uniform raw material feed to processing facilities, (3) improve blending of finished bulk materials from storage. DragScraper systems are being used effectively for handling a variety of bulk materials in both indoor and outdoor storage. Materials being handled include ores, chemicals, coke, clay, and stone, to name a few. Handling capacities these machines can provide vary from a few tons to over 1500 tons per hour. The basic components of a DragScraper machine consist of a bottomless Crescent scraper, a two or three-drum DragScraper hoist assembly including gas, diesel, or electric power unit, operating cables, guide blocks, and either fixed or mobile head and tail structures. They are presently available in sizes through 15 cubic yards, for operating spans up to 1000 feet.

Jan 1, 1969

By J. Kircher

Nevada Goldfields' Aurora Mine consists of a 270 mtpd (300 tpd) precious metals mining and milling facility located 28 miles southwest of Hawthorne, Mineral County, Nevada and lies within five kilometers of the Nevada-California border. (Figure 1) Ore production presently is derived 85% from an open pit source with the balance from underground. The Aurora Mill is a compact conventional cyanide plant utilizing a carbon-in-leach extraction process followed by stripping of loaded carbon and electrowinning at Nevada Goldfields Kingston Mine, located near Austin, Nevada. Production commenced in December 1987 and annual gold production is currently 20,000 troy ounces of gold and 22,000 troy ounces of silver per annum, produced at an average cash cost of $178 per ounce of gold. Tailings handling at, Aurora was originally accomplished using a belt filter press producing a solid cake that was then transported to a final storage area. Although overall operating costs at the mine were' in the lower percentile of producing gold mines, the tailings handling portion of the operating costs were inordinately high.

Jan 1, 1989