Search Documents

By Reed J. Irvine

One normally does not find sudden and dramatic changes in the investment climate, barring the unexpected outbreak of-wars or revolutions. Asia has seen a fair amount of military action and revolt during the past year, not all of it unexpected There was the fighting in Laos, which resulted in the as yet unconcluded negotiations which will probably lead to the establishment of a neutralist regime. In April of 1961 another revolution occurred in South Korea, and the elected government was replaced by a military dictatorship.. Communist guerrilla activity in South Vietnam was stepped up, and uncertainty about the future of that area increased. Relations between Pakistan and Afghanistan became more strained, and while no fighting has broken out, diplomatic relations between the two countries were broken off. India was both the victim of further incursions of her territory by communist China and the perpetrator of the forcible seizure of territory from Portugal. Indonesia has been making preparations for an armed attack on the Dutch in New Guinea.

Jan 1, 1962

By R. Klimpel

Recent work has shown that the measurement of flotation kinetics in the laboratory is useful in providing guidelines on how operating sulfide flotation plant performance can be improved. This work outlines the influence of various factors on flotation kinetics such as collector/frother type and concentration, particle size, and frother blending.

Jan 1, 1981

By H. R. Bullis

Lupin is located on the shores of Contwoyto Lake at lat. 65° 48'N, Long. 111° 15'W and lies about 80 kilometers south of the Arctic Circle. Since start up in 1982 the mine has produced over 2.15 million ounces of gold from 6.66 million tonnes of ore grading 10.63 gm/tonne. Total remaining reserves at 1993 year end were 5.1 million tonnes at a grade of 9.11 gm/tonne (1.65 million ounces). This is sufficient for 7 -8 years at the present annual production rate of about 200,000 ounces. The Centre and West Zones of the deposit are open to depth. The deposit is in an Archean metaturbidite sequence of the Contwoyto Formation, which has been mapped as part of the Yellowknife Supergroup of supracrustal metasedimentary and metavolcanic rocks making up part of the Slave Geologic Province. These rocks have been subjected to regionar and contact metamorphism and to several phases of deformation. Six stages of Archean plutonism have been identified and all Archean rocks have been cut by Proterozoic diabase dyke swarms. Gold mineralization in the Lupin deposit is commonly fine grained and associated with pyrrhotite and arsenopyrite in amphibolitic banded iron formation. The gold-bearing portions of the host iron formations are characterized by the presence of multiple quartz veins and the pervasive replacement of grunerite by hornblende. In sparsely mineralized portions of the host iron formation, zoning of sulfides about quartz veins is clearly seen with the arsenopyrite halo being more restricted around the veins than the pyrrhotite halo. In well mineralized portions, quartz vein densities approach one vein per metre along strike. In these areas pyrrhotite distribution in the iron formation is more pervasive and the rock takes on the appearance of a banded sulphide rock.

Jan 1, 1995

By Mark L. Munsell

In recent years, miners have tried many approaches to maintenance such as: - Highly sophisticated computerized programs. - large planning groups designed to preplan and schedule work. - Contract maintenance. - Break down maintenance. Each of these approaches has faced the added constraints: - High replacement cost of equipment necessitating longer useful equipment life - management?s increased scrutiny of all indirect costs such as maintenance. Faced with these factors, what system of maintenance control is right? After visiting many properties recently, it appears there is no right system. Maintenance programs need to be tailored to the people and production constraints that occur at an individual property.

Jan 1, 1976

By N. S. Tanious

This paper summarizes the results of an investigation into possibly the largest coal pillar failure in the USA. The newly opened drift mine is located in Southeastern Kentucky and worked an 11 feet thick coal seam, all other mines in the District worked seams 4-5 feet thick. The initial mine development consisted of 14 main entries (Fig. 1) which were driven in two sets of 7, under increasing depth of overburden. As the left seven entries came under deeper overburden the pillar ribs began sloughing which caused many of the concrete-block ventilation stoppings to crack. The mine management stopped the advance in the left seven and continued with the right seven entries. During the spring of the following year development resumed in the left seven, rib sloughage occurred again and this time severely cracked many stoppings and many were totally disintegrated from the excessive deformation. Within few weeks the sloughage was so heavy that many of these entries behind the active face were filled with piles of sloughed coal slabs. When the face reached a depth approximately 1150 feet, the sloughage became a slow, massive squeeze. The entry convergence (closure) reduced their height from 11 to 7-8 feet and the squeeze spread back to shallower depth covering an area roughly 300 pillars.

Jan 1, 1989

By Carl E. Williams

Several years ago it was decided that ASARCO was in need of a good mine scheduling program to complete the computerized open pit mine planning package that was being used on new prospects and operating properties. A trial and error approach was being used to schedule a mine on a year by year basis, but this was time-consuming and far from offering an optimum solution l. Due to the magnitude of time and expertise required to develop such a sophisticated computer program, it was decided to search outside of the company for one already developed and available for purchase, This proved fruitless and therefore proposals were requested from consulting firms that had the expertise to develop such a program. Out of the five firms that submitted proposals, the one chosen was Systems Control, Inc., (S.C.I.) of Palo Alto, California. S.C.I. was selected because it was felt that they offered the greatest capability in the mathematical solution of complex problems. But due to their lack of mining expertise, a cooperative venture was developed whereby ASARCO would supply this mining knowledge. The selection of this vendor, the formulation of the contract and specifications, and the development of the computer program required about 3 years to accomplish.

Jan 1, 1973

By D. Nutakor

Rock joint stiffness is not only a poorly known parameter, but also has no established laboratory measurement procedure. This paper presents methods used to determine the normal and shear stiffnesses of healed joints filled with vapor-altered minerals obtained from the Yucca Mountain site in Nevada. Results show that these joints behave linearly up to 85% of their loading history and are stiff with strengths very close to the strength of the intact rock. Factors that might have contributed to the linear behavior of these joints are discussed and areas requiring further investigation are provided. Joint normal stiffness ranges from 7.16 to 64.77 GPa/mm with an average value of 26.93 GPa/mm, while joint shear stiffness averages 11.41 GPa/mm and ranges from 3.09 to 28.41 GPa/mm. Young?s modulus of the vapor-altered joint infilling was calculated from the stiffness of the healed joint. Young?s modulus of the vapor-altered joint filling material averages 7.89 GPa and ranges from 2.15 to 19.43 GPa. Given the pervasive presence of such altered rock, usually in the form of sub-spheroidal 3-D pockets, this property should be of value in any numerical modeling attempting to describe the mechanical behavior of these tuff formations at the level of detail where inclusions might be a factor.

Jan 1, 2008

By F. L. Wilke

Bong Mining Co. Ltd. in Liberia, West Africa, operates an iron ore open pit some 60 miles northeast of Monrovia. The production is at present about 40,000 t/d (metric tons/day) from which about 18,500 t/d concentrate with 65.5% Fe is produced. The ore waste ratio is about 1: 1.5 to 1:2. The technical layout and the equipment are very similar to those in many modern open-pit operations as described by Jacobs and Thomson (1967). As described by Lersch in detail (1966), the deposit is a very irregular one. The quality of the ore changes within very short distances with regard to both physical conditions (hardness) and chemical properties. Very soft and very hard ore as well as high-grade and low-grade ore are found adjacent to each other. In addition, there are enclosures of sterile rocks. For the purpose of identification and production scheduling, 12 different types of ore are distinguished.

Jan 1, 1979

By Dr. Peter J. Conroy

The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to the DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. This paper summarizes the work that has been completed through September of 1981 and presents the results that have been achieved during this period. Technical difficulties encountered during both the installation and monitoring phases are discussed, and recommendations for future work are presented.

Jan 1, 1982

Iron removal using biologically produced organic acids was investigated as a treatment option for the production of refractory grade bauxite. A leaching solution containing 98mM oxalic and 67mM citric acid was prepared from a sucrose medium using for fermentation the fungus Aspergillus niger. The leaching capacity of the metabolic product was tested on a bauxite sample containing 16-19% iron (as Fe2O3). Aerobic and anaerobic leaching tests were carried out at pH 3, 50°C and in the absence of light. Results indicated that more than 80% of total Fe can be removed from the ore, when the sample is finely ground and applying a two stage treatment. The presence of oxygen was seen to affect adversely the kinetics of the process, suggesting that leaching follows a reductive mechanism. Experiments that were carried out with different particle size fractions indicated that for obtaining efficient removal of iron particles should be finer than 0.63mm. Reduction of the operating temperature from 50 to 30°C caused a decrease in the rate of iron removal by more than 10 times.

Jan 1, 2006

By Jacob Feld

Introduction The best way to eliminate the possibility of rapid excavation in tunnel work is to start an argument between Owner Engineer and Contractor. And arguments are readily started when work is progressed without a frank open agreement on the rules of the game. Fifty years ago a tunnel contractor took a job to excavate and line a tunnel, providing all labor and materials under the guidance and continuous instruction of the Engineer who provided all survey work, checked each new heading and set the lines for the next round of drill holes, usually designed and ordered protective measures, kept record of progress and controlled payment for the work. In my first job in a tunnel, muck cars were loaded by hand and hauled by donkeys. Progress was, at today's criteria, not rapid. The Contractor or in the case of a large concern, his executive field representative was always at the site, knew most of his men by name, and there was a mutual feeling of respect between him and the Engineer in charge of the work. Misunderstandings were cleared up when they came up, expeditiously and fairly, even though satisfaction was not always expressed. The Owner came for the ground breaking and usually for the holing through shot. The Owner had full reliance on the Engineer's ability and integrity. The Engineer recognized the Contractor's expertise in being able to man the job and produce results.

Jan 1, 1974

By Elza F. Burch

Feeding 600 pm X 0 raw coal to heavy media cyclones, along with the +600 pm size coal, produces an efficient separation of both the +600 pm and 600 pm X 150 pm sizes. Major advantages of the process include the elimination of desliming screens and secondary fines circuitry for cleaning the 600 pm X 150 pm size coal, and result in a very simple circuit. Incorporating four 660 mm diameter heavy media cyclones, the Providence Plant of Island Creek Corporation has operated efficiently for ten years with a magnetite consumption rate of less than 0.45 kg per ton of raw feed at a feed rate of 454 tph.

Jan 1, 1988

By N. S. Tanious

This paper summarizes results from an investigation into possibly the largest coal pillar failure in the USA. The newly opened coal mine worked an 3.35 m (11 ft) seam under overburden depth that ranged from 91 to 671m (300 to 2200 ft) . The mine main entries, and the enclosed pillars, experienced a massive slow squeeze. The squeeze could not be controlled and the mains were lost. A new set of mains were driven. Entry convergence (closure) measurements were carried out behind the advancing face to monitor stability. Pillar stresses were also measured under four different depths of overburden: 229.433, 472.579 m (750,1420,1550, and 1900 ft). The strength of pillars in the new mains was calculated from the loads that triggered the failure in the old mains, using three pillar strength formulas. The stress measurements showed that the new pillars supported more load than their predicted strength, indicating that current strength formulas are inadequate under deep conditions.

Jan 1, 1992

By A. L. Williamson, G. Savci

Hydrologic assessments of existing and proposed waste rock stockpiles (WRS) are typically required for application of operating and closure permits at mine sites. The results of these assessments can be used to determine the applicability of the state groundwater permit program requirements to the operation and closure of these stockpiles. The objective of this hydrologic assessment was to ascertain whether or not the WRS at the Ajo Mine have a reasonable probability of discharging potential pollutants to the underlying aquifer under the operational mine conditions. The hydrologic assessment was performed based on an evaluation of climatic data, prediction of the net infiltration rate through the WRS and prediction of additional hydrologic factors such as the time required to deplete available moisture storage in WRS. The predicted net infiltration rates ranging from 0.13 inches/year (1.1x10-8 cm/s) to 0.24 inches/year (1.9x10-8 cm/s) are below the threshold value of less than 10-7 cm/s recommended by Hutchison and Ellison (1992) as being characteristic of conditions that produce no or negligible quantities of seepage. In addition, the total time required to deplete available moisture storage within the Ajo Mine WRS and for any potential seepage from the WRS to reach the underlying aquifer is estimated to range from 260 years to 1,950 years. Collectively, the climatological and geotechnical investigations and the hydrologic predictions demonstrate that the WRS at the Ajo Mine hydrologically do not have a reasonable probability of discharging pollutants to the underlying aquifer. As a result of this prediction, the stockpile will not be regulated under the state groundwater permit program and operational and reclamation requirements will be limited to managing surface water runoff.

Jan 1, 2002

By A. M. Stone

Following the conceptual idea of a Continuous Elution Process early in 1982, the system was successfully pilot plant tested at Western Mining's Kambalda gold plant in December 1982. As a consequence of these tests the Ok Tedi elution ciruit design was changed from batch operation to continuous operation resulting in a reduction in the number of similarly sized elution columns from five operating with one standby to one operating with one standby and halving the process steam requirements. In addition to providing significant capital and operating cost savings the continuous process was simpler to operate than the batch process.

Jan 1, 1989

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

By Julian Prada

Tunneling requirements are presenting designers with greater challenges. The design and construction of the 2000-ft long unidirectional twin highway tunnels for the approach to one of two bridges of the Louisville-Southern Indiana Ohio River Bridges (LSIORB) Project is no exception. Excavation under low cover, beneath an historic site, with each tunnel of 70-feet wide and 50-feet high dimensions will set precedents for US highway tunnel excavation size. To investigate ground conditions to supplement final design of the highway tunnels, an exploratory tunnel excavated through karstic limestone and shale will be located within the confines of the proposed final alignment. With the LSIORB Project, Jefferson County, Kentucky and Clark County, Indiana will have improved cross-river mobility between them. The Indiana Department of Transportation (INDOT) and the Kentucky Transportation Cabinet (KYTC) are developing the LSIORB Project jointly, in coordination with the Federal Highway Administration (FHWA). Section 4, one of six sections, as shown in Figure 1 is the East End Kentucky Approach and Connections to I-265. Key elements of Section 4 are the twin three-lane highway tunnels under the historic Drumanard Estate. The property is located on the north side of US Highway 42 (US 42) at the intersection with the Gene Snyder Freeway (also KY841) as shown in Figure 2. One aspect of the project consists of the excavation of an Exploratory Tunnel along the southbound alignment tunnel. At the time of preparation of this paper, KYTC has not awarded the Exploratory Tunnel Contract. This paper will focus on the planned geotechnical investigation program that will occur during excavation of the exploratory tunnel and how the design of the twin highway tunnels will incorporate the findings to achieve an innovative and efficient configuration.

Jan 1, 2008

By G. H. Thomas, M. C. O’Riordan, S. Rae

INTRODUCTION The British mining industry comprises 228 nationalised coal mines producing some 113 million tonnes of deep mined coal and employing 242,600 persons of whom 185,200 work below ground. There are in addition 174 small privately-owned coal mines employing 1500 persons underground and producing 1.5 million tones of coal. In the non-coal sector there are 108 privately-owned mines producing some 20 different minerals, including tin, wolfram, fluorspar, potash, rock salt, china clay, ball clay and fireclay. There are currently 4,100 persons employed in these mines of whom 2,346 are employed below ground. One mine producing potash employs 870 persons of whom 465 are underground workers. Since 1975 all matters relating to the health and safety of persons at work and of the general public who are exposed to industrial hazards have come within the purview of the Health and Safety Executive (HSE). The Mines and Quarries Inspectorate (MQI) is a constituent part of that organisation and enforces legislation applicable to all mines and quarries. The National Radiological Protection Board (NRPB) is a statutory and independent body that was established in 1970 to advance knowledge and provide information and advice about radiological protection. The NRPB has an agency agreement with HSE to provide advice and services relating to radiological protection, including protection against exposure to radon decay products in mines. There are as yet no statutory requirements controlling exposure to this source of radiation in Britain. Investigations for the presence of radon in British coal mines were begun in the mid 195Os. The concentrations found were of low order, typically around 2 pCi/l (Duggan et al., 1968). This was not surprising since big coal mines are well ventilated to control methane and airborne dust and it is now generally accepted that radon and its decay products do not constitute a health hazard in British coal mines. At one or two small mines where igneous intrusions were in close proximity to the coal workings, slightly higher readings were recorded. The MQI then commissioned NRPB to make investigations at metalliferous mines and in these much higher readings were detected. It was later agreed that the NRPB should undertake a survey of all non-coal mines in Britain to establish the extent of the problem. This survey was conducted mainly in 1973, (Strong et al.,1975) and follow-up surveys at various mines have since been conducted by the MQI. These investigations revealed that radon readings could be high in mines producing tin, haematite and fluorspar. Some small mines working other minerals in the same localities also showed high readings. More recently owners have been making environmental measurements at mines where there was some cause for concern. LEGISLATION AND RADIATION STANDARDS As a result of the survey work for MQI the Board in 1975 recommended an occupational limit of 4 WLM in a year from radon decay products together with a programme of radiological supervision (Strong et al., 1975). The MQI accepted the recommendation and advised employers and employees that the 4 WLM limit should be adopted. The limit corresponds to a concentration of 0.3 WL, equivalent to 30 pCi/l of radon-222 in equilibrium with the decay products, and was in accordance with an earlier recommendation by the International Commission on Radiological Protection (ICRP, 1959). ICRP recommendations are usually endorsed in Britain. It was recognised that some years would probably be required to achieve general compliance, and this is proving to be the case. Some confusion has been caused in Britain by the conflict between successive Euratom Directives on this and other standards of safety. As relative newcomers to the Community, we were not affected by earlier Directives, but the situation is different now. In 1959, the Commission of the European Communities provisionally recommended a maximum permissible concentration for radon-222 and daughters of 3 x 10-7 µCi/cm3, which corresponds to 300 pCi/l (CEC, 1959). The number was affirmed in 1962 (CEC, 1962) and reaffirmed in 1966 (CEC, 1966) but without any specification of the state of equilibrium. In 1976, the CEC again recommended 300 pCi/l, but on this occasion, the daughters were assumed to be present in the same quantities as in unfiltered air (CEC, 1976): this implies 40 WLM a year in poorly-ventilated mines. The formula is repeated in the latest version of the Directive (CEC, 1980), but the value is now said to be an interim one because it might not ensure compliance with the appropriate dose limit. ICRP (1955) recommended 300 pCi/l in equilibrium with the decay products in 1955 and reduced this value to 30 pCi/l for unfiltered air in 1959 (ICRP, 1959), endorsed it for equilibrium conditions in 1976 (ICRP, 1976), and held to it until 1980: these values imply respectively 40 and 4 WLM a year. The recent recommendation of the ICRP (1980) that the annual limit of intake for the decay products should be 0.02 J in a year corresponds to 5 WLM, but there is a rider that reduction should be made for exposure to gamma rays and long-lived airborne radioactivity. An allowance of 20% is suggested for uranium mines, implying 4 WLM a year for the decay products. The

Jan 1, 1981

By Perry N. Halstead

The primary objective of the structural geology portion of the Kennecott Copper Corporation-U. S. Bureau of Mines Pit Slope Stability Study was to determine the attitude, geometry, and spatial distribution of geologic structures of the west wall of the Kimbley Pit for use in designing a maximum stable slope for the pit. A corollary objective was to develop and refine techniques for collecting and analyzing geologic structural data with emphasis on numerical methods that could be integrated with other aspects of pit design. Surface mapping techniques used were a modification of conventional joint set mapping and a detailed linear sampling method. For subsurface investigations both oriented core and a borehole camera were used. It was determined that the major faults in the area were favorably oriented for mining a steep stable slope. The jointing or natural fracturing, although complex, was not random in attitude and consisted of several persistent fracture sets and a number of secondary sets. The attitude of the persistent fracture sets was favorable for steeper slope angles, and these attitudes were used in the design considerations. There was no significant difference between the attitude of the fracture sets determined from the former and new slope face.

Jan 1, 1968

By S. Strömberg, A. Jokilaakso

Two complex copper concentrates and one arsenical nickel concentrate were oxidized in simulated flash smelting conditions using a laminar-flow furnace. The concentrates contained tetrahedrite as Sb-bearing mineral and arsenopyrite and gersdorfite as As-bearing minerals. At high temperatures and low oxygen potentials, Sb tended to vaporize, but with high oxygen potentials it was captured in mixed oxide phases with copper and iron. Arsenic was found to follow antimony in copper concentrates, although with less sharp contrast between low and high oxygen potentials. In the nickel concentrate studied, arsenic was found to vaporize from the gersdorffite particles and, subsequently, condense on the other particles.

Jan 1, 1998