Search Documents

By E. Baliktsis

PPC (Public Power Corporation) operates a new power plant at the South-West part of Crete. Recently the extension of the Power Plant started. ATHENA SA the main contractor of the project assigned to EXORIXI SA the implementation of a blast vibration monitoring program and prevention-evaluation of risks caused by construction blastings inside or very close to the operating part of the power station. The blasting parameters and characteristic elements that had been evaluated, the measures that had been taken and materialized, the overall risk management and the results of the whole program are presented in this paper.

Jan 1, 2006

By Joseph P. Gildner, Michael S. Kucker, Robert A. Robinson

Considerable controversy seems to exist over the extent and nature of information that should be provided in design-build type contracts. Much of this controversy may relate to the types of owners, ranging from private industry to state and federal agencies that are implementing design-build. Philosophies for the development of geotechnical information ranges from no information to a thorough investigation approaching that needed for final design. Several recent projects, such as the Channel Tunnel in Europe, Whittier Tunnel in Alaska, Tren Urbano in Puerto Rico, and Sound Transit in Seattle have taken varying approaches to providing and interpreting geotechnical information for bidders. The pros and cons of these various methods are discussed and assessed.

Jan 1, 2001

By James F. Reynolds

Introduction There are 1.4 Gt (1.5 billion st) of recoverable coal under less than 914 m (3,000 ft) of cover in Colorado in pitching seams. Snowmass Coal Co., in cooperation with the US Department of Energy, introduced the longwall mining method in pitching seams to North America. This venture is a coal mining research program directed toward the profitable production of coal under difficult mining conditions as found in pitching seams of the western US. Snowmass Coal classifies pitching seams into the following categories for longwall on the strike in seams 3 m (10 ft) or less thick: • Flat = 0 to 10°: Normal continuous mines and shuttle cars work efficiently. • Slight = 10° to 22°: The maximum pitch that rubber tired equipment will function. • Moderate = 22° to 40°: The angle of repose of mined coal. • Steep = 40° to 60°: The limit of safe use of this roof support. • Vertical = over 60°. The longwall roof support covered here will work in all pitches except vertical. The shearer and conveyor will work in flat through moderate conditions. Longwalling across strike with this equipment in seam pitch over 60° could be accomplished with an inclined face. Development of the first longwall panel began in 1979 and was completed in 1981. The longwall equipment was installed and mining began on Aug. 11, 1981. Mine Planning and Development The original mine plan took advantage of old works abandoned in the 1960s. The gates were developed on a two-entry system with the entries rising 2° to the strike, allowing water to drain from the face. The mining method was by Alpine F6A road header continuous miners with bridge conveyor type coal transport into 5.4-t (6-st) bottom dump coal cars hauled on 1.1-m (42-in.) gauge track by 7.2-t (8-st) battery locomotives. The initial concept was to haul coal from the longwall by battery locomotive. Lack of discipline, however, was shown in the irregular direction of the gate entries, and local rolls in the coal seams severely limited the capacity of battery locomotives. Current mining law prohibits using an intake escapeway for belts or trolley locomotives. A two-entry system is the simplest method of panel development in a pitching seam. A continuous miner cannot be trammed from one entry to another because of steep "X" cuts. Thus, the development requires a continuous miner in each entry. The configuration of the old mine works resulted in a first panel longwall block of three 108 m x 1.6 km (355 ft x 5,400 ft). In panel development, the use of battery locomotives for coal hauling became evermore costly. When the panels were completed and the setup room finished, the lower gate entry was changed to a belt entry and battery locomotives were abandoned. A new slope was driven and the mine supply system was converted to rubber tire diesel supply. The latest generation of roadheader and standard high powered shuttle car-to-belt system is now used for development. Selection of Longwall Equipment Longwall mining across the strike on pitching seams is currently practiced in many nations. Equipment similar to that used by flat seam longwalls is available for pitching seam use in Great Britian and Germany. Face equipment includes a twin outboard armored face conveyor. It was selected to give maximum retention of coal on the conveyor due to flight rigidity and to prevent coal from sliding down the face and jamming the lower belt gate. Also selected was a 22-mm (0.9-in.) Dowty twin-outboard face conveyor for a 106-m (350-ft) face with a single 112-kw (150-hp) drive

Jan 12, 1983

By Michel Grenier, Mahendra Gangal

Two methods used to measure the exposure of mine workers to diesel exhaust particulate were compared. One method was developed by the U.S. Bureau of Mines and the University of Minnesota's Particle Technology Laboratory. The method which was originally developed for use in coal mines is a size selective sampling technique. The other method uses an “ashing" approach to assess the exposure to diesel particulate. This second method is based on the principles of sampling according to the ACGIH respirable dust sampling criteria and the use of a silver membrane filter as collection substrate. Because a silver membrane filter is used, both respirable combustible dust (diesel particulate) and respirable silica can be measured from one sample. The comparison study took place in a Canadian lead-zinc mine during tests which were primarily designed to evaluate the gaseous and particulate emissions characteristics of new diesel engine technology. The study has shown that under the test conditions encountered, some differences were observed between the results as obtained by the two methods. These differences seem to depend on the characteristics of the respirable dust found in the work- place, i.e., size and composition. The impact, on sampling and analysis of diesel particulate, of the proposed guideline (ACGIH) for a TLV® of 0.15 mq/m3 is discussed briefly.

Jan 1, 1997

By Henry N. Doyle

One can hardly discuss coal pneumoconiosis unless it is placed in the context of the total pneumoconiosis problem in the mining industry. However, it might be well if first we defined a few terms, since it has been my experience that the use of the word pneumoconiosis frequently causes con- fusion among those who are not familiar with the term. Pneumoconiosis comes from two Greek words meaning lung and dust. Hence, the word pneumoconiosis simply means dusty lung, or dust on the lung. There are many forms of the disease, some of which are disabling and some are not. Among the many dusts which cause pneumoconiosis might be included silica, asbestos, coal, talc, iron ore, and many other mineral dusts. Silicosis is a specific form of pneumoconiosis. It is caused by the inhalation of excessive amounts of silicon dioxide in the form of crystalline quartz. The disease is manifested by nodulation of the lungs which is apparent on an X-ray film. Continued exposure to silicon dioxide causes the nodules to grow and ultimately large areas of the lung become scar tissue which pre- vents the lung from performing its physiologic function. In its more advanced stages, there is a significant loss of pulmonary function which accounts for

Jan 1, 1966

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013

By Gonzalo Barrientos

Instrumentation and observation of real mine structures helped define the pressure arch at White Pine, a large copper mine in sedimentary rocks. The pressure arch, which is attributed to inherent horizontal stresses, is used in the design of mine openings.

Jan 1, 1969

By Madhu G. Ranade

A statistically designed pot grate- kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables, bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate, were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a pl ant trial. The target firing temperature at the Empire Plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets

Jan 1, 1985

By Rolf J. Wesely

Recent events in The Peoples Republic of China indicate that a major effort is underway to increase trade with the western world. Gold production contributes to China's ability to participate in international trade. Consequently, the Chinese government places a high priority on increasing gold production. Many of the operating gold mines in China contain refractory ores that to date have not been efficiently treated. Figure 1 illustrates the description and location of a few of China's major gold mines. China recognizes that the technology necessary to economically treat this ore has been developed in the United States and other western countries. The country has therefore begun to seek assistance in evaluating several potential projects. Organizational structure Gold mining and processing in China is directed by the China National Gold Corp. (CNGC), headquartered in Beijing. The agency has a director in each province who is responsible for exploration, mining and processing. CNGC uses the services of two engineering organizations for metallurgical testing, process development and design engineering for their projects. The largest engineering organization is the Central Engineering and Research Institute for Non-Ferrous Metallurgical Industries (ENFI), also located in Beijing. The second engineering organization is the Changchun Gold Design Institute (CGDI), located in Changchun Jilin province.

Jan 1, 1993

By Michael M. Donahue

"The public interest -- as opposed to the narrow interests of particular shippers -- will also benefit from the establishment of adequate revenue levels and the revitalization of the railroads. And this is particularly true with respect to the transportation of coal. "

Jan 1, 1981

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By William W. Edgerton

The California Department of Transportation (Caltrans), the Contra Costa Transportation Authority (CCTA), and the Alameda County Congestion Management Agency (Alameda CMA) are involved in a unique partnership on the planning and design of the fourth bore of the Caldecott Tunnel, located on State Route 24 in Alameda and Contra Costa counties. The project will add a two-lane bore north of the existing three bores. The project will alleviate traffic congestion in the non-peak direction. This paper provides background on the existing facility, summarizes the need for the new fourth bore, describes the proposed improvements, sets forth the approach for project delivery, and lists some of the challenges that are expected during construction.

Jan 1, 2008

By J. E. Rourke, O&apos

This paper describes the use of index testing to obtain rock properties that are useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include: point load; Schmidt hammer hardness; abrasion hardness; and total hardness. The first two index properties correlate to uniaxial compressive strength (UCS) and Young's modulus. Discussions are given on empirical, normalized relationships of UCS to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The hardness property indices correlate to construction performance parameters and some relevant experience is cited. Examples of data are presented from an index testing program carried out primarily on siltstone, sandstone and limestone rock core samples retrieved from depths up to 1005 m (3300 ft) in a borehole drilled in the Paradox Basin of eastern Utah. The borehole coring was done for a nuclear waste repository site investigation.

Jan 1, 1990

By J. B. Hiskey, V. P. Atluri

Resin-in-leach (RIL) cyanidation experiments were performed on a refractory carbonaceous gold ore. The objective of this investigation was to determine if strong-base ion exchange resins could adsorb the soluble aurocyanide complex in preference to natural "preg robbing" organic constituents. Direct cyanidation of the carbonaceous gold ore used in this study resulted in less than 2% gold extraction in 24 hr. RIL cyanidation resulted in about 70% gold recovery onto the resin. Kinetic experiments indicated that 50% of the gold is extracted after 1 hr of leaching. Resin breakage was investigated for as-received and preattrited resins. Similar results were obtained with three different strong base resins.

Jan 1, 1990

By Harry E. Hughes

A section of the largest Superfund site in the country has become a success story for engineering innovation and for cooperative problem solving. “Superfund site” and “success story” are phrases that are not commonly found in the same sentence. Yet, their use seems justified. The project’s certification of construction completion from the US Environmental Protection Agency (EPA) includes a commendation. It reads, “for completing the project nearly a year ahead of schedule, at a cost substantially less than estimated originally and without com-promising the requirements for protection of human health and safety or the environment.” The EPA director who issued that certification also referred to the project as “a positive example of cooperation among all who have a stake in the outcome.”

Jan 1, 1996

By John C. Braithwaite

Gold production commenced in New Zealand during the gold rush of 1861, and recovery to date is over 900 tonnes, almost 60% of which was alluvial. New Zealand pioneered development of bucket line dredges during the 1880's. The advent of the modern hydraulic excavator and increased gold price led to a resurgence in alluvial production with about one hundred plants in operation in 1988. The processing plants are mainly floating, with throughputs of 50-100m3/hr fed by backhoes of 20-40 tonne operating weight. Some larger plants with more sophisticated recovery systems have commenced over the last few years, with the largest using a 180 tonne backhoe.

Jan 1, 1989

By Todd Minoski, KRISTIN FLOYD, Michael Murphy, VASU GANGRADE, Gamal Rashed, DYKE MARK VAN, Brent Slaker

Underground stone mines frequently operate on multiple mining horizons or are required to undermine or overmine old workings. In these situations, the effects of pillar columnization and interburden thickness on the stresses surrounding mine workings are poorly understood. Many old workings were not designed to consider the effect on future undermining or overmining and, as a result, are laid out on irregular patterns and with pillar sizes that are difficult or impossible to replicate on adjacent levels. Additionally, as depth increases, even a consistent gridded mine layout may result in poor columnization due to the need to increase pillar sizes. Rules of thumb and past practice for designing multiple levels may often be effective. This paper explores the effect that multiple-level stone mining has on stress redistribution through the discussion of two case-study mines and associated numerical modeling to provide additional insight into situations which may cause concern.

The dissolution behavior of gold and silver from Au/Ag alloys in aerated cyanide solutions has been investigated using rotating disc electrodes. The variables studied included concentration of cyanide, oxygen partial pressure and rotating speed of the disc. The dissolution potential and the rate of dissolution were obtained in view of the anodic and cathodic current-potential relationships. The results were discussed in terms of a mixed potential theory. The results showed that the dissolution rate of gold and silver from the alloys was partially controlled by chemical reaction, but largely by transport of either oxygen or cyanide, depending on their relative concentration under the experimental conditions employed in this study.

Jan 1, 1995

By C. Rutter, N. SHEA, K. KOLOBE

Henderson Mine’s primary production transitioned from the main portion of the 7700 level to the 7210 main panel in 2005. On the 7700 level, the southwest (SW) panel was brought into production in 2014 and produced through 2020. A-Panel was brought online in 2019 and took over primary production in 2020. The 7210 north panel is under development with production expected to commence in 2025. The 7700 northwest panel is expected to be the mine’s last production panel.

By James M. Barker, Richard O. Y. Breese

The recognition of perlite as a distinct volcanic glass, and of the arcuate fractures that often characterize these natural glasses, dates back at least to the late 19th century and perhaps into the 18th century (Howell, 1974). Some authors suggest that recognition of perlite dates considerably further into antiquity, perhaps to the 3rd century BC (Caley and Richards, 1956). Most recent definitions identify perlite by the presence of vit¬reous, pearly luster and by the presence of characteristic concentric or arcuate perlitic fractures. As discussed more fully below, arcuate fractures in perlite need not be megascopic. The textures of perlite which commonly occur in deposits range from dense to highly vesiculated to pumice-like. Thus, the classical definition of perlite is descriptively restrictive compared to the natural range of textures and neglects to address the issues of genetic origin and geologic occurrence. In spite of the petrological usage of the term perlite, the in¬troduction of expanded perlite aggregate into industrial markets caused the term to be applied as well to the lightweight, cellular aggregate that is produced through the rapid thermal expansion of milled perlite ore. Perlite is distinguished petrologically from other natural glasses by a silicic or rhyolitic composition by the presence of 2 to 5 wt% total chemical water held within the glass structure and often by the presence of pearly luster and onionskin-like perlitic fractures. Worldwide, occurrences are associated with Tertiary through early to middle Quaternary volcanics and with the glassy portions of silicic domes and flows, with vitric tephra, with the glassy chill margins of dikes and sills, and with the glassy portions of welded ash flow tuffs. Less commonly, perlite is reported in association with the glassy portions of volcanic plugs and lacco¬liths. The perlite carapaces that partially or fully comprise extru¬sive domes and flows are often thick and areally extensive, and thus provide commercially attractive targets for low cost open pit mining. Perlite tuffs and tephras are also important commercial sources. Mining costs are minimized by open pit quarrying and by either bulldozer ripping or blasting. Crushing and sizing facilities are generally close to the pits. Due to the low weight and large volume of expanded perlite, unexpanded perlite that has been crushed and sized is usually shipped nationwide directly to local markets where it is expanded and processed for distribution to end users. The vast majority of international trade is in unexpanded perlite. In the United States, the evolution of the expanded perlite industry can be traced to the late 1930s and early 1940s when expanded perlite aggregate was introduced into gypsum plaster and concrete markets as a substitute for vermiculite (Schundler, Jr., oral communication, 1991) and was promoted for use in a much broader spectrum of products (Howell, 1974). By the early 1950s, end user markets were well established and small expanders were numerous east of the Mississippi River. Today, mining and expan¬sion is undertaken throughout the world. Worldwide production of perlite is dominated by the former Soviet republics, the United States, and Greece. Total worldwide production of processed perlite during 1990 is estimated at roughly 1 778 000 tons (Davis, 1991). The physical properties of expanded perlite that give this prod¬uct unique commercial value include: low bulk density, chemical inertness, high insulating ability, nonflammability and fire resis¬tance, and its ability to retain water. These and other physical properties give expanded perlite value in such uses as: lightweight acoustical and thermal insulating aggregate; component in plaster, insulating cements and lightweight concrete; loose fill insulation; as aggregate in horticultural applications; and in milled form as filter aid. In the United States and Europe, the largest end use is within building construction products.

Jan 1, 1994