Search Documents

By Lynn I. Kelley

Industrial-mineral production contributes on the order of CDN$1.5 billion per year to the economy of Saskatchewan, Canada. Potash is the primary industrial mineral produced in the province, followed by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium-chloride brine, and "clinker." Potentially economic deposits of kaolin, diamond, and building stone are under evaluation. All of the major deposits of commodities discussed here are located south of lat 56°30'N. Most of the locations are presented on Figure 1 POTASH Saskatchewan supplies approximately 30% of the world's demand for potash. Eight conventional underground mines and two solution mines produced an all-time high of more than 13 million metric tonnes of potash (KC1) (8 million tonnes K2O equivalent) in 1997, valued at over CDN$1.4 billion. All of the mines exploit the middle Devonian Prairie Evaporite. The four potash-bearing members of the Prairie Evaporite underlie much of southern Saskatchewan and extend southward into North Dakota and Montana and east- ward into Manitoba (Fig. 2). Halite and anhydrite separate the potassic members. The evaporite beds locally are interrupted by solution structures (anomalous ground). Some of the structures may be related to deep-seated tectonic features.

Jan 1, 1999

By D. W. Park

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floor and thinly-laminated immediate roof. The investigation covered by this paper concerns a mine that was experiencing ground-control problems with weak floor conditions. Four hundred ft above the presently producing seam, another seam has been mined out. Several roof falls occurred locally, and as much as two ft of floor heaves have been experienced. The paper presents the results of comprehensive analysis conducted on floor heave, roof sagging, and the influence of the mined-out seam using instrumentation and numerical analysis.

Jan 1, 1991

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (KO88) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron- and steelmaking and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By S. C. Tadolini

Roof support systems have evolved from standing posts and timbers to a generation termed ?big nails? where steel bars are inserted into boreholes and anchored with expansion shells and/or resin cartridges. These systems have been effective but are limited to mining height. Additionally, the properties of steel do not resists shear forces or have the flexibility being required in difficult ground conditions. The next generation of roof support systems is coupling the best parts of the ?big nail? and resin grouted cable bolt systems. This paper will present the advanced technical solutions of the next generation of cable systems that includes an indented high-capacity PC-strand used with a variety of fixtures. Case histories of support applications will be presented.

Jan 1, 2012

By K. H. Boss

In modern iron pelletizing plants fuel consumption has been optimized to such an extent that only minor savings can be expected in the future. Inspite of this fact, different process parameters were studied with a mathematical model and firing tests. The influence on fuel consumption and productivity was established. Furthermore, the adoption of simplified firing patterns was investigated, in particular for coal firing. In view of high costs of oil and natural gas, only substitution of these fuels by coal can substantially reduce production costs. In existing plants partial replacement of oil and gas can be achieved by addition of coal to the iron ore feed and by firing the pellets with pulverized coal. Two systems have been developed for the Lurgi- Dravo travelling grate process which enables coal to completely replace oil or gas. This paper describes in the first part the potentials for fuel savings available in the Lurgi-Dravo process. In the second part, different techniques for the use of coal as fuel in iron or pelletizing plants and in particular the recently developed Lurgi Multistage Coal Injection and Combustion Process (LMC) are discussed. Combined with the LMC process, a wide variety of iron ores and coals - also with high ash contents - can be used in the Lurgi-Dravo travelling grate process.

Jan 1, 1983

By J. W. Leonard, D. A. Newman

By using physical and chemical means to increase the bulk density of newly broken coal freed from the mine face, the potential to improve coal mine productivity is significantly enhanced. It is estimated that by increasing bulk density, greater tonnages can be placed in fixed volume scoops and shuttles cars to improve production by as much as 10% to 20%. Such improved packaging to achieve new levels of volumetric efficiency might require only small and easy to implement changes to present downstream mining operations. Opportunities exist for improving broken coal bulk density from the moment of breakage, during transport across the continuous miner or loading machine, during discharge into the haulage unit, and after placement in the haulage unit. Physical/chemical methods for broken coal compaction in mobile, fixed volume units in underground operations are discussed.

Jan 1, 1990

By Karen M. Kessen

The isotopic variations of lead from Mississippi Valley galenas have long been used to place constraints on the sources of the lead, and on the residence the of the lead in crustal reservoirs prior to its emplacement in the Mississippi Valley province. Similar studies based on strontium isotope variations in gangue minerals associated with the lead-zinc sulphides have been neglected until Haden's (1) study of such minerals from several localities in northwestern Ohio. His work revealed two things about the mineralization. Firstly, it shoved that the average isotope composition of lead from galenas from northwestern Ohio lies on the anamalous lead line characterizing Mississippi Valley-type leads, albeit at the least radiogenic end of the entire data array. This confirm earlier assignments of the Ohio mineralization as Mississippi Valley-type (Hey1 and others (2)). Secondly, Haden (I) showed that the strontium in the calcite, strontianite and fluorite is broadly similar in isotopic composition to the strontium in the host Silurian to Devonian marine carbonates within which these minerals arc emplaced. He concluded that the mineral strontium my have been very locally derived, from the carbonate hosts.

Jan 1, 1979

By James J. Scott

Introduction Friction Rock Stabilizers, trade name Split Sets, are presently under research and development by Ingersoll-Rand Company and Dr. James J. Scott, inventor. Conceived in 1953, the system is a patented process undergoing extensive field and laboratory testing. The author has published papers on the Split Set System earlier (References 4, 5, 6) The Split Set System holds promise to be a revolutionary development in the field of ground control. The system produces an interior reinforcement to a rock mass which: 1. Is simple in its concept. 2. Adjusts to the degree of restraint needed to match rock properties. 3. Provides a yieldable support and, later, a more rigid support as it is needed. 4. Pre-loads the rock in compression to increase stability. 5. Is a full-contact, fully tensioned device to resist rock loads. 6. Minimizes the stress concentration effects inherent in many interior support devices. 7. Improves safety for the miner. 8. Is cheaper than a grouted system. 9. Offers the rock mechanics engineer an opportunity to design in a fashion not before possible.

Jan 1, 1977

By R. Hogg, L. G. Austin, R. C. Klimpel

Slurry densities and holdup were measured for open circuit grinding tests in a laboratory overflow ball mill of 0.3 m diam by 0.6 m long, by emptying and drying after stoppage of the mill. Contrary to some other results in the literature, there was negligible variation of slurry level in the mill as a function of flow rate over a range of increase of flow rate of about 5 to I. However there was a gradual increase of solid holdup at higher flow rates because the slurry density in the mill increased. Equations are given for holdup and slurry density in the mill as a function of over flow diam, ball load, and feed slurry density. The average level of slurry necessary to give over flow was found to be much higher than that necessary to fill the mill to the overflow level at rest. The total level of balls and slurry was only increased slightly by ball loads higher than the overflow level. The overflow diam appeared to be the major controlling factor in determining the mill holdup.

Jan 1, 1990

By John A. Ames

Limestone for portland cement must be beneficiated to produce uniform raw material for the kiln. Careful quarrying and selective recovery are factors in this process, but the chief aspects of beneficiation are "in plant" processes, such as crushing and screening, washing, grinding, flotation, and heavy-media separation. Numerous technical and economic problems exist. Detailed studies of the limestone deposit and the stone itself are required for intelligent beneficiation. As used in this paper, beneficiation is defined as the improving of limestone composition so as to produce an economically usable raw material A limestone deposit is defined as a mass of limestone which can be recovered, by quarrying or mining, for sale or for use in a commercially profitable operation. The stone may require elaborate processing, or it may qualify with little or none. Obviously, the "commercially profitable" qualification may change as the economy changes. Potentially commercial deposits may be of much better quality than actually developed deposits, and yet may be denied development for various economic reasons.

Jan 1, 1966

By R. V. Ramani, K. V. K. Prasad

Forecasting mined grade variability from exploration information is a challenging task in mine planning. For effective planning of activities, such as workplace scheduling, ore grade quality control, etc., development of realistic numerical simulation models of in situ variability from exploration information is an essential first step. Geostatistical conditional simulation (GCS) is one of the well known methods to develop such simulations. Recently, stochastic fractal models based on the assumptions of scale-invariance and self-similarity have been used for developing simulations of several natural phenomena. It has been suggested that these models might permit the generation of short-scale variability information from exploration data with greater fidelity when the data satisfies the attendant assumptions. In this paper, stochastic fractal models are reviewed, and their relationship to geostatistical variogram models is examined. A comparison of the two simulation techniques has been performed using coal sulfur data from a mined-out coal property. The results of this comparative analysis are also presented in the paper.

Jan 1, 1993

By Kenneth K. Humphreys

27.1-HISTORY, PROCESSING STATISTICS KENNETH K. HUMPHREYS 27.1.1-MINERAL PROCESSING HISTORY The processing of minerals predates recorded history. Many processing techniques have existed for thousands of years. For example, Georgius Agricola, in De Re Metallica (1556), described equipment and techniques, such as picking tables, smelting furnaces and cupolas of various types, sieves, launders. various types of crushers and grinders and other equipment, all still in use in one form or another. In translating Agricola's work into English, the late Herbert C. and Lou Hoover provided the following summary indicating the early history of particular mineral- processing operations :

Jan 1, 1973

By Robert L. Russell

Production at Freeport Indonesia's Ertsberg open pit copper-gold mine started in 1972 at a rate of 7.5 kt/d (8270 stpd). Mill throughput remained at that rate for several years until the discovery of the Ertsberg East (GBT) ore body. This discovery prompted three succes¬sive expansion stages from 1981 to 1988 that boosted production to 20 kt/d (22,000 stpd). In 1988, the discovery of the huge Grasberg porphyry copper deposit launched an era of much larger expansions. The first of these was the installation of a fourth primary mill in 1989 that increased throughput to 32 kt/d (35,270 stpd). That was followed by an expansion of the crushing and screening plant and in 1991 the addition of a new south concentrator to bring production to 57 kt/d (62,830 stpd). The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 brought production to its current level of 66 kt/d (72,750 stpd).

Jan 1, 1994

By J. Craynon, M. Karmis

Previous papers by the authors have presented a systems-engineering approach based on the premise that systems can only be optimized if all factors are considered and integrated into mine planning. This paper discusses the challenges inherent in optimizing the design of large-scale surface coal mining operations in Appalachia. Regulatory and permitting programs in the United States often focus on single parameters, rather than the full suite of desirable outcomes for sustainability. By utilizing geographic information system (GIS) tools to evaluate available data on environmental and social resources, the regulatory barriers which prevent operations from incorporating ecological and other sustainable development concerns into coal mine sustainability performance were identified. By analysis of the on-the-ground issues related to sustainability, the key parameters to be incorporated into an optimized coal mine design in Appalachia are discussed along with possible changes to the regulatory framework that would enhance incorporation of sustainability into coal mine design.

Jan 1, 2011

By A. K. Haines, M. W. Godfrey, D. M. Miller, P. C. van Aswegen

The Bacterial Oxidation [(BIOX)] process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairvew Mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developmenst to improve plant operating efficiencies. These new developments, which include a higher solids content of the pulp feed to [BIOX], lower retention times, higher operating temperatures, lower power utilizaton for oxygen dispersion and reduced nutrient addition, have all been successfully implemented on the Fairvew plant. It has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Contineous cyanidation pilot plant work conducted on [BIOX] product has indicated that cyanide consumption can be drastically decreased if a continuons flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1992

By J. M. Mutmansky, Y. J. Wang

The usual method employed to determine the direction of flow in a connecting airway in advance is to conduct a survey between the two existing nodes being connected by means of the new airway. It is then assumed that airflow will take place from the node with higher pressure to the node with lower pressure. The purpose of this paper is to examine this direction-of-flow problem -- using properties of the system characteristic curve for a two-terminal network -- and specify some conditions that ensure that flow will take from the higher-pressure node to the lower-pressure node. It is concluded that the only requirement is that all characteristic curves of fans in the network should be strictly decreasing. Five numerical examples illustrate some important properties of the direction-of-flow problem.

Jan 1, 1999

By Christopher Laughton, Michael P. Bruen

At Fermilab, a 4000-ft long underground complex has recently been constructed for a high-energy physics experiment. The complex is sited up to 350 ft, below grade principally in bedrock. The rock excavations were mined by TBM and drill and blast methods and supported by a combination of rock bolts, dowels and shotcrete. Water control was achieved using a combination of pre- and post-excavation grouting, drainage systems, drip shielding and air desiccation measures.

Jan 1, 2003

By I. Stavrakas

This work studies the variations of the electric current caused by the application of an electric field on marble samples when they are subjected to continuously increasing mechanical stress at a constant rate up to fracture. The external electric field is applied in a direction perpendicular to the applied mechanical stress. An increase of the level of the electric current was observed when micro-damages started to occur in the samples. The increase of the electric current was approximately 14%. Consequently, the current started to decay abruptly and the sample failed. This electric current recording is compared with the corresponding electric recording without applying the external electric field (Pressure Stimulated Current technique). Both recordings show similar qualitative characteristics. The most obvious of these characteristics are that the electric current starts to develop when microcrack structures start to form due to the externally applied stress. Both recordings show a maximum in the vicinity of fracture.

Jan 1, 2008

By N. T. Rempe

The underground voids that result from mining provide opportunities for deep geologic waste disposal (DGWD). Such disposal could solve many environmental problems. DGWD takes careful planning, technology transfer and true partnership between waste generators and mine/repository operators. The US government is now planning on using specially mined excavations to dispose of radiotoxic and mixed waste. Using the experience gained from the domestic projects that are now in preparation and from foreign repositories that are now in operation, US mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1997

By R. E. Weeks, D. J. Millenacker

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time- frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The US Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1987