Search Documents

By Anis Farah, Khosrow Aref

Pull-out tests were conducted on cable bolts grouted with concrete, and cement paste. The influence of several parameters on the performance of these cables were studied under loading rates varying from very slow to relatively fast. These parameters include water-cement ratio, cable surface conditions, curing time and embedded length. In addition to being more economical, the results indicate that cables grouted with concrete have higher ductility and ultimate bond strength as compared to those with cement paste only.

Jan 1, 1986

By Mohammad Djavid

The one-pass tunneling pipe jacking method has often been the most schedule and cost efficient method for the pipe line installation. The main challenges in jacking pipes larger than 108 inches and for longer runs are: transportation and logistics, requiring high jacking forces, keeping line and grades, control of ground surface settlement, providing adequate external lubrication, and the potential of damaging the joints and pipe spigots. In recent years, 144" diameter pipes have been jacked for short runs of up to only 300 feet. In this article design and construction of installation of up to 1,000 linear feet run of 144-inch internal diameter, reinforced concrete pipes without intermediate jacking station in Chicago O?Hare International Airport are discussed. The article also presents discussions regarding the subsurface saturated silt formation, shallow cover, dewatering, jacking and receiving shafts, jacking forces, lubrication and settlement data.

Jan 1, 2008

By Jaime Lomelin

The brines from the sub-surface of the Laguna del Rey dry lake are pumped to Química del Rey, S. A. plant, where they are cooled in adiabatic crystallizers precipitating sodium sulphate decahydrate. This salt is dehydrated in multiple effect evaporators and dried in rotary kilns producing high purity anhydrous sodium sulphate. The spent brines from the sodium sulphate operation are concentrated in solar ponds, precipitating astrakanite and leaving a brine with a higher concentration of magnesium ions. This brine is treated with calcium chloride solution to eliminate the remainder of sulphates, leaving a solution of magnesium chloride ready for the manufacture of refractory grade magnesium oxide or periclase. The magnesium chloride is reacted with dolime to produce magnesium hidroxide which is washed, filtered, and calcined to produce soft burned magnesium oxide, which is briquetted and dead burned to produce the periclase.

Jan 1, 1984

By Dominick Mandalari, David Mast, Heather Ullinger, Juan Granja, Amanda Foote

The City of Akron will construct the Northside Interceptor Tunnel (NSIT) project to control and reduce combined sewer overflows. One component of the project a large diameter tunnel diversion / flow control structure that will facilitate tunnel storage, divert dry weather flow to the treatment plant, and divert large wet weather events that are greater than the tunnel capacity to the Cuyahoga River. The structure is designed to pass up to 1.2 billion gallons per day of flow and includes floatables screening. This paper will discuss project background, factors that influenced shaft location, and options evaluated to manage the large design flows.

Jun 23, 2024

The thermal field of a frozen rockmass surrounding an airway is often disturbed due to thermal interaction with mine ventilation air. Outside air entering an underground mine changes the parameters of the physical state of the surrounding medium. The variations in air temperature result in stress redistributions around a tunnel or mine working. This paper examines the influence of fluctuations in air temperature on stress distribution around an airway, and approaches are suggested to minimize the impact of temperature- stress on the stability of mine openings in far northern mines.

Jan 1, 1991

By J. R. J. Edwards

Jaspilite, a mineral consisting of silica and iron oxide in varying proportions, is one of the host rocks of the high grade ore deposits situated in the Middleback Range of South Australia. As a result of laboratory investigations, a flowsheet was postulated for the beneficiation of jaspilite to produce an acceptable grade product for feeding to blast furnaces, The flowsheet involved the reduction of the hematite in the haspilite to magnetite, the grinding of the reduced product to 95 pct minus 325 mesh Tyler followed by wet magnetic separation, hydroseparation and filtration to yield a magnetite concentrate. Agglomeration of the fine concentrate would then be necessary to meet the physical requirements of blast furnace feed. To prove the postulated flowsheet, to obtain a more accurate estimate of costs and to obtain design data for a commercial installation, a pilot plant was constructed at Whyalla, South Australia.

Jan 1, 1960

By Steve Karl, Rock Jenkins

Continuing its objective of sharing new ideas, methods, theory, and engineering developments, more than 550 members of the underground fraternity gathered in New York City for the 1985 Rapid Excavation and Tunneling Conference (RETC). Since the first meeting in 1972, RETC’S aim has been to lay a foundation of tunneling experience on which the industry could expand and develop over the years. The RETC is jointly sponsored by the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the American Society of Civil Engineers, in cooperation with the Canadian Institute of Mining and Metallurgy, and the Engineering Institute of Canada. The 17 sessions included 72 papers that explored up-to-date practices in the mining and civil engineering fields. Session topics ranged from geotechnical and seismic design, through design, construction, and support of underground openings, to ground water control in shafts and mine openings. Case histories of tunnel boring machines and large diameter tunnel and underground openings were also reviewed. All the papers presented at the three-day conference are valuable additions to improving the state of rapid excavation. A few sessions, however, are particularly noteworthy as they are geared to the mining industry. The two volume proceedings of the entire conference are available from SME. (See ad on page 1003).

Jan 7, 1985

By J. T. Sitarski, R. C. Emmett, L. W. Luinstra, R. P. Klepper

A mining operation in Zimbabwe produces a pyritic gold concentrate that requires oxidative pretreatment prior to cyanidation in order to liberate 80 percent of the gold values. Bio- oxidation offered the potential of increased gold recovery and was considered to be an economically advantageous alternative to the existing practice of roasting the concentrate. Based on bench- scale test work, a small bio-oxidation plant, capable of processing approximately 50 percent of the concentrator production, was installed at the mine to evaluate this approach. The plant included two 57 m3 bioreactors in series and the ancillary equipment needed to prepare the feed concentrate, to wash the leached residue prior to cyanidation, and to neutralize the waste liquor. The plant was operated for a year-and-a-half, and the conditions needed to achieve a 90 percent liberation of gold values were determined. A number of critical technical problems were encountered, and many were resolved on-site. Others have been addressed since the pilot plant was moth-balled in June 1988. Valuable insight was gained from the operation of the pilot plant, which has provided useful guidance for continued process and equipment improvement.

Jan 1, 1990

By L. R. Nelson

Cyprus Pima is a medium-sized open-pit copper mine located 35 km (22 miles) south of Tucson, AZ. The ore body was discovered using geophysical prospecting methods in 1953 and was originally worked as a small underground mine followed by small open-pit operations. As mining equipment grew larger and the economic ore grade dropped, the operation grew in size, through four expansions, to the present 50 500 tpd (56 500 stpd) milling rate. The remaining stripping ratio is about 2.5 to 1. Mining equipment includes 11 electric shovels ranging in size from 6 to 15 m3 (8 to 20 cu yd) and 42 diesel-electric haulage trucks ranging in size from 89 to 223 t (100 to 250 st). Mine planning is performed at Cyprus Pima to serve several functions. The most important is to plan ahead, one year at a time, to predict the ore grade and stripping requirements on a month-by-month schedule. This yearly plan is necessary for budget preparation and is revised once each quarter to incorporate variations in actual production experienced during the preceding quarter.

Jan 1, 1979

By Prof. Dr. T. R. Boulos

The Egyptian marine phosphorite of Sebaiya West, the Nile Valley, consisting of both non-oxidized hard siliceous and oxidized leached friable ore types, is subjected to a roughing-cleaning silica flotation circuit for production of wet-process phosphoric acid concentrate. Operating at its maximum capacity of 268 t/hr, the following were the main problems encountered during the early stages of running the plant: 1. The tremendous amount of slimes generated by scrubbing the crushed ore causing turbidity in the plant thickener after a short time of operation, regardless of the added flocculant. 2. Rod mill choking leading to inefficient performance of all other equipment and poor flotation results. 3. The drastic increase in imported oleic acid price. Pulp density and slurry flowrate measurements at different points of the plant as well as ore microscopy, size distribution analysis, chemical analysis and x-ray diffraction analysis of representative ore samples coupled with Work Index measurements of feed samples showed that the wide variation in the ore's hardness was responsible for such problems. Application of the locally produced non-edible rice bran oil as a substitute to imported oleic acid in flotation resulted in total saving of U.S.$2 million in 1990. The total unsaturated fatty acid content of the oil is high, ranging from 75.2 to 81.5 mole % of which the C18-unsaturated fatty acid content ranges from 72 to 79 mole %.

Jan 1, 1993

By I. Papadopoulos

Nowadays, geophysical prospecting is implemented in order to resolve a diversity of geological, hydrogeological and geotechnical problems. Though plenty of applications and a lot of research have been conducted in the country-side, only a few have been reported in the literature concerning urban areas, mainly due to high levels of noise present that aggravate most of the geophysical methods (e.g. electromagnetic, seismic, gravity etc.) or due to spatial limitations that hinder normal method implementation (e.g. electrical). Among all geophysical methods, electrical tomography proves to be the most rapid and urban noise insusceptible technique. This work presents a case study in the urban area of Hania (Crete I., Greece), where Electrical Resistivity Tomographies (ERTs) have been carried out for the detection and identification of possible buried ancient ruins or other manmade structures, prior the foundation of a building. Nineteen profiles were surveyed in a 20x40m grid using dipole-dipole configuration. The results indicate two areas of interest, that are interpreted as probable old wells, in the context of the existence, in former times and in the same area, of an olive oil plant. In the vicinity, near surface ancient ruins have been disclosed, but no such evidence provided this survey, for the particular area under study and the prospected depth. The collected ERT-data were processed by applying advanced algorithms in order to obtain a 3D-model of the study area that depicts more clearly and accurately the interesting subsurface structures.

Jan 1, 2005

By Michael E. Berndt

Asbestos first became an issue to Minnesota?s iron industry when it was revealed that mineral fibers similar to those in Reserve Mining?s tailings were being found in drinking water for several communities that used Lake Superior as their primary water source. This discovery turned what had largely been an environmental court battle into a case concerning public health. The courts listened to much conflicting and uncertain scientific testimony on the size and distribution of the mineral fibers and on the potential health effects imposed by them. In April 1974, the plant was ordered to shut down by a federal judge but the company quickly appealed the decision. The appeals court granted a stay and ultimately ruled that the plant?s closure could not be justified based on the unknown health effects of the mineral fibers since the consequences of such an action would have immediate and severe social and economic impacts. The plant was allowed to continue operation, but ordered to abate emissions to air around the plant and to switch to a land-based tailings disposal system. Much of the scientific uncertainty and public concern over mineral fibers in Minnesota?s taconite industry remain today. ©2007 Elsevier Inc. All rights reserved. Keywords: Minnesota; Iron ore; Taconite; Asbestos; Amphibole; Reserve Mining; Tailings; Mesabi Iron Range

Jan 1, 2007

By M. M. Botz, F. W. DeVries

Discussion by F.W. DeVries Comments on natural cyanide attenuation. The paper by Botz and Mudder in the November 2000 issue of Minerals and Metallurgical Processing had one disappointing aspect. Table 1 (p. 229) failed to include a significant species - neutral copper cyanide (CuCN). This compound has been most trouble-some in many plant-scale cyanide cleanup processes, includ- ing acidification-volatilization- reneutralization (AVR), hy- drogen peroxide cleanup and air/SO2 cleanup. It has also plagued many pilot efforts to use ion-exchange (IX) resin technology. This author elucidated the concept that, under some conditions, copper cyanide failed to precipitate out of treated effluents and appeared to exist as a filterable colloid that reported as copper and cyanide, with the latter measured as WAD (weak-acid-dissociable) cyanide in that analytical method. The concentrations measured were very near the levels of 0.2 ppm, often the regulatory limit for WAD cyanide. The copper concentration, using the 1 : 1 ratio for this com- pound, would then be more than 0.4 ppm, which could also be unacceptable. We discovered that it was unsafe to assume that the Cu(CN),- would surrender both cyanide ions simultaneously and allow cupric copper to be removed subsequently as, say, cupric ferrocyanide (Hatchett's Brown). This compound could be ignored as safely as the "iron blues," as essentially an inert solid, stable in geologic time if not exposed to sunlight. Under poorly controlled oxidation of the cyanocuprite ions (copper with four, three or two cyanides complexed to the copper), CuCN could well be formed and could not be assumed to precipitate out as a solid. The authors of the paper, by failing to include the CuCN species in their model, may have left users of the model prone to ignore the possible occurrence of the colloidal(?) form in the discharge, thus finding an effluent that failed to meet regulatory limits. (See addendum below.) This somewhat ephemeral material may well have been responsible for some large-scale failures of cyanide destruction technology to succeed at sites in North America and elsewhere. Two specific references alluding to this occurrence may be found: Griffiths et al., 1987, "The detoxification of gold-mill tailings with hydrogen peroxide," Journal of the South African Institute of Mining and Metallurgy, September, p. 282. DeVries, 1989, "Improved understanding in detoxification of cyanide leach liquors using peroxide" Rand01 Gold Conference, Sacramento CA, p. 15 1. It is advisable for workers in this area of cyanide removal or recycle to avoid assuming that CuCN will, with certainty, precipitate out of solution, or that the dicyanocuprite ion will part simultaneously with both cyanide ions and allow cupric copper to be dealt with by other reactions. One further piece of work may be incomplete. That is, a definitive study of the long-term behavior of CuCN that does precipitate when exposed to other compounds present in neutralized tailings. Addendum. The extremely complex reaction of cupric ion on cyanide- which, of course, results in oxidation of cyanide to cyanate, probably through the intermediate stage of forming cyanogen [(CN)2] from oxidation of HCN with its hydrolysis to cyanate and cyanide ion - involves two cyanide moieties and the reduction of the cupric ion back again to the cuprous state. This, then, can form the CuCN potential "solid" that was already the undesirable species. In cyanide cleanup, with either air/SO2 or hydrogen peroxide, copper is generally employed as the catalyst, so it is unclear what happens when the CU(CN)2-1 is ultimately exhausted. Certainly, the field evidence is quite clear that all

Jan 1, 2002

By E. Steel, V. S. Znamensky, A. Wylie

The asbestiform habit is most commonly developed in certain amphiboles and chrysotile, but other minerals also may crystallize with this unusual habit. The habit may be characterized by (1) a fibril structure, single or twinned crystals of very small widths (generally less than 0.5 pm), which have grown with a common fiber axis direction, but are disoriented in the other crystallographic directions; (2) anomalous optical properties, primarily parallel extinction; (3) unusual tensile strength; (4) high aspect ratio; and (51 flexibility. In addition, there is evidence to indicate that some amphibole asbestos may have unusual surface properties. ASBESTOS AND THE ASBESTIFORM HABIT Asbestos is defined as a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven, are heat resistant and chemically inert, and possess a high electric insulation, and therefore are suitable for uses where in- combustible, nonconducting, or chemically resistant material is required (Gary, et al., 1974). The most common minerals that may occur with the asbestiform habit are chrysotile, grunerite (amosite], riebeckite (crocidolite), actinolite, anthophyllite, and tremolite; although the development of this habit among these minerals is rare. Other minerals, most notably other amphiboles, can occur in this habit, but no others have been mined commercially as asbestos. All asbestos is confined to metamorphic rocks, even though other habits of the amphiboles are common in igneous rocks. Slip fiber veins are the most common deposits (South African amosite, Canadian chrysotile, etc.), but mass fiber deposits also may occur such as California chrysotile or mountain leather. Field relations and experimental data support the hypothesis that metasomatism is the dominant process in the formation of asbestos fibers, amphibole as well as serpentine. The crystal habit of a mineral is the shape or form a crystal or aggregate of crystals take on during crystallization. The asbestiform habit has a number of characteristics that differentiate it from other habits. Chief among these is the fibril structure.Afibri1 is a single or twinned crystal with a very small width, generally less than 0.5 pm, and an extremely high aspect ratio; bundles of fibrils may have lengths reaching into the cm. Fibrils share a common crystal growth direction along the long axis of the fiber, but appear to be disoriented with respect to one another in the other crystallographic directions. The structure of the individual fibrils, and the organization of fibrils within a fiber may differ among the various types of asbestos. The fibril structure of asbestos is probably a factor in controlling a number of secondary properties that include high tensile strength, flexibility sufficient for weaving, and anomalous optical properties. The high tensile strength of asbestos is quite remarkable, exceeding that of the ordinary varieties by a thousand fold (Zoltai, 1978). In part, this may be attributed to the lack of defect on the fibril surfaces (Zoltai, 19781, but some contribution also must come from the existance of bundles and the nature of the ordering of and forces among the fibrils. The flexibility is not only enhanced by the fact that the fibrils may slip past one another, but by their small widths and extreme aspect ratios. However, structural defects parallel to the fiber axis also may contribute to this property. Among the common commercial asbestos types, the greatest flexibility is found in chrysotile and the least in grunerite asbestos (amosite), varying inversely with fibril thick- ness. In addition, at least for chrysotile, composition also may affect the flexibility of the fibers. Finally, most asbestos minerals are mono- clinic, but optically display parallel extinction (Heinrich, 1965, and Wylie, 1978). This also must be due, in part, to the ordering or lack of ordering of the fibrils. The fibril structure is probably a random

Jan 1, 1986

By L. C. Bartel

Geologic features such as structure (faults, folds, fractures, etc.), water bearing zones, aquifers, pemeability variations, and porosity variations are important for mine planning and in situ energy recovery processes. Features important for planning a mine will be important for planning the recovery of energy by in situ processes. Various geophysical techniques might be used to obtain the necessary geologic information. In this paper, case histories will be discussed of the use of electromagnetic geophysical surveys at a potential underground coal gasification site and a potential tar sand oil recovery site to obtain pertinent geologic information. Results show that the controlled source audio- frequency magnetotelluric technique shows promise for mapping faults and natural fracture systems when there is a sufficient resistivity contrast.

Jan 1, 1982

By T. E. Mccandless

Detrital minerals of mantle origin have been found in the Green River Basin of Southwestern Wyoming (Figure 1). Pyrope, pyrope-almandine, and chrome-bearing clinopyroxene and orthopyroxene occur on the antmounds of Pogonomyrmex Occidentalis. These antmounds are a common sight throughout the western U.S., and were used by early paleontologists as fossil mammal collection sites. The mound is composed of two types of material; (1) soil excavated during the digging of the nest below the surface (maximum depth 3 meters) and (2) larger grains collected from the surface and placed on the mound, probably to prevent erosion. The selection of grains to armor the mound seems to be based largely on the mean diameter of the grain, with other factors such as weight, sphericity, roundness and composition in decreasing order of importance (Wheeler and Wheeler, 1963). The minerals of this study happen to fall within that mean diameter range. The garnets are found on the mounds as 3-6 mm diameter subrounded to subangular grains. The pyroxenes are also 3-6 mm in diameter and are most commonly subangular laths. The minerals themselves show evidence of abrasion, such as frosted surfaces and rounded edges. Orange peel texture is present on some of the grains, which suggests that kelyphitic rims were once present, but have been removed. Also, no similar minerals were found in sieved soil auger samples to depths of 2 to 6 meters taken near the antmounds. These observations imply a distal rather than proximal source for the minerals. Lamproitic rocks of upper mantle origin are found bordering the "Green River Basin. The best known are the Leucite Hills, a series of ultrapotassic volcanics found on the north flank of the Rock Springs Uplift (Carmichael, 1967). Minor occurrences of mica peridotite and ultrapotassic volcanics are also found on the western end of the Uinta Mountains in Utah (Best, et al, 1968). None of these rocks are known to contain minerals like those on the antmounds. The garnets are comprised of purple chrome pyrope, red chrome pyrope-almandine, and pink to orange low chrome pyrope/pyrope-almandine. Oxide statistics for these groups are summarized in Table 1. These three groups are distinct when their Cr203 values are plotted against magnesium number (Figure 2). The chrome pyropes are highest in Cr203 (1.28-2.66%) and have high, restricted Mg number values (0.781-0.826). The chrome pyrope almandines have similarly high Cr203 (1.29-2.62%) but a lower Mg number range. The low chrome pyrope/pyrope-almandines have the lowest Cr203 content (0.09-0.73) and the widest Mg number range (0.534-0.836). Using the classification scheme of Dawson and Stephens (1975) the chrome pyropes are most similar to garnets derived from kimberlite and from garnet lherzolite, websterite, and harzburgite xenoliths in kimberlite. The chrome pyrope-almandines and the low chrome pyrope/ pyrope almandines are similar to garnets derived from eclogite nodules (Figure 3).

Jan 1, 1984

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

By James C. Conti

A surface charge sensor has been developed that responds to changes in the double layer properties of colloidal silica during the cationic flotation of silica from taconite ores. Sensor design allows for the measurement of two aspects of the electrical double layer surrounding all solids immersed in ionic solutions. One aspect responds to a flow induced change in the double layer properties of a solid. The other is a function of the chemical composition of the aqueous phase. Evaluation of sensor performance during froth flotation experiments has been encouraging. Process monitoring capabilities are indicated.

Jan 1, 1981

By Richard R. Klimpel

The first part of this two-part article summarizes the result of a 10-year, multimillion dollar research and plant testing program involving operating mining companies throughout the world. The program was aimed at developing a better understanding of the influence of slurry rheology on the performance of mineral/coal grinding circuits. Part 1 presents the basic concepts identified, including typical laboratory results showing the influence on grinding behavior of controlled changes in percent solids, particle size, slurry temperature, and viscosity control chemicals. Part 2, in January, will illustrate typical industrial scale test results on both open and closed circuits using the concepts presented in Part 1. Special emphasis will be placed on identifying some industrial operating implications of controlling rheology by different methods. Introduction The industrial-scale practice of wet grinding minerals and coals in tumbling media mills (ball, rod, and pebble) is well-known to operating mineral processing engineers and plant design personnel. Over the last century, considerable experience and data has been collected, correlated, and put into rules or guidelines for successful circuit design and operation. Typical factors influencing circuit throughput that have been analyzed in some depth are mill diameter and length, grinding media size and loading, feed and product particle size, mill power use, and the interaction of classifier type and efficiency with the grinding device. Until recently, knowledge of slurry rheology influence on large scale grinding circuit performance has been limited. Even today slurry rheology effects are essentially ignored in plant design. Indeed, in most plant operations only qualitative guidelines are followed. For example, too thick a slurry causes throughput losses and too thin a slurry uses excessive water or causes water handling problems such as pumping limitations. A search of published literature and numerous discussions with experienced plant operating personnel has shown an awareness that changing the percent of solids in the mill influences grinding or the response of grinding involving fine feeds versus coarse feeds. However, most the work identified relative to rheology effects in mineral/coal grinding was qualitative. Even in the few studies that were more quantitative, the scope of the work was usually too narrow to draw general conclusions. Also, the detailed rheological characterization tied to observed breakage and the combination of laboratory to industrial-scale testing that is required to develop a broad understanding of any factor influencing grinding had not been done. In this environment, this detailed program began in 1967. It had three distinct goals: • To develop a basic understanding of slurry rheology influence on breakage characteristics in the laboratory. • To test general rheology concepts developed in the lab on the industrial scale. • To develop a commercially viable chemical approach to controlling slurry rheology that would lead to the use of chemical grinding additives or grinding aids. The goals have been met, at least in part, this year. A small fraction of the extensive laboratory and plant results have been made available in published literature. Much of the research program dealt with identifying and developing chemical grinding aids, but a lot of useful and practical information on percent solids, particle size, and slurry temperature influence on grinding circuit performance also was collected. The purpose of this article is to present a clear and concise sum¬mary of the results of the entire program. The importance of rhe¬ology control in grinding circuit behavior will be demonstrated using a series of carefully per¬formed industrial scale experi¬ments (both open and closed cir¬cuits) that have not yet been reported in general literature. Mining companies participating in the test program on a proprie¬tary basis have found the informa¬tion in this article to be useful in better understanding and improv¬ing circuit performance. Viscosity Effects in Grinding Studies In this program&apos;s previous labo¬ratory studies, it was shown that there is a consistent pattern of change in specific rates of break¬age of both mineral and coal slur¬ries as slurry fluidity changes. Using the net production rate of material smaller than some spec¬ified size-for example, kg/hr of <75 µm (200 mesh)-as an index of mill production in a standard batch mill test (with a given feed material, feed size, mill, and mill conditions such as constant time of grind), the following facts were established (see Fig. 1): • The normal range of low den¬sity, low viscosity slurry (region A) gave no variation in mill produc¬tion. The measured rates of break¬age exhibited normal first order grinding. • Grinding of a somewhat higher viscosity slurry (region B) could give increased production. The higher viscosity was obtained

Oct 12, 1982

By J. den Drijver, M. Opahle, R. Inderst

Safety reasons render necessary the advanced calculation of the amount of methane degassing from a longwall in the scope of the ventilation planning of mines. Today empirical methods, which are based on observations of operational procedures, are used for the calculation of the amount of methane. Despite of constant improvement those calculations are not always sufficient. In particular calculations which are based on operational facts but not proved by experience are not reliable. Most of all these calculation procedures lack physical-analytical descriptions of the procedure itself, presenting only the effects on important parameters such as the distance between seams in the roof or floor or gas pressure. Tschersich [Tschersich 961 developed an analytical model for an advanced calculation by analysing the degassing of seams in the roof and floor and the physical parameters of gasflow. This model might correct the lacks of existing procedures and improve the precision and reliability of additional calculations. The model simulates the emission record in seams of the roof and the floor. It takes into account not only a multitude of parameters such as the distance to adjacent seams and gas pressure but also the depth of seams, gas content, rank of carbonification, rock temperature, face advance rate, initial and succeeding mining and the face length. In order to comprehend and to verify those correlations we extended the model of Tschersich and programmed this enlarged model using the computer language C++. Aim of this research is to guarantee a much higher accuracy in calculating methane emission caused by mining. The improved planning is expected to result in more safety and better prevention of high methane con- tent in ventilation as well as in a better use of the capacity of the mining equipment. The application [Drijver, lnderst 961 of the ex- tended model will also be very useful in the course of research projects as it allows computer simulation, i.e. in-situ research can be extensively limited or even replaced.

Jan 1, 1997