Search Documents

By Charles Stone, Madan Naik, Drupad Desai, Karel Rossler

Planning of New York’s new subway line dictated the location of shallow underground station caverns and track crossovers. Clear span openings ranging from70 feet to 100 feet and lengths in excess of 1000 feet, coupled with low rock cover ranging from 25 feet to 40 feet required judicious selection of construction methods, equipment, and proper sequencing of the excavation stages. Rock classifications alone could not predict the behavior of the rock mass during construction. A robust design procedure that considered most of the important aspects of rock behavior and elements of shallow tunnel design, minimized the negative impacts of variable geotechnical data. This paper describes the intricacies of the planning and design of the $16 billion Second Avenue Subway with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2005

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986

By M. K. Gangal, E. D. Dainty

The CANMET diesel-related work, carried out in cooperation with the Canadian mining industry, resulted in the identification of several useful R/D studies. One such study was the development of a dash-mounted alarm signal system to indicate overexposure of production LHD diesel vehicle operators to toxic contaminants in a mine environment. The resulting instrument has been called the [CO2 Exposure Meter]. This meter is particularly applicable to LHD machines because previous investigations have indicated that operators of LHDs and some haulage truck drivers are exposed to up to 200% of the contaminant concentrations measured in the general mine return air. This paper describes the development of the system which continuously monitors and displays the operator's exposure to diesel pollutants, and indicates an overexposure by an alarm light. The overexposure limits are preset by mine personnel based on carbon dioxide (CO2) measurements, which in turn are related to simultaneous spot respirable combustible dust (RCD) measurements (or to Air Quality Indices - AQI, if available). The CO2 settings are, in general, related to the engine/exhaust treatment selections, vehicle duty cycle and local ventilation rates and efficiency. The system continuously displays one of three lights: green for underexposure, yellow for caution, and red for overexposure. Overexposure can occur for several reasons, such as: reduced ventilation, malfunction of the diesel vehicle, and excessive airborne contaminants. The paper confirms satisfactory operation of the system in a laboratory-simulated mine environment, as well as in field trials.

Jan 1, 1993

Continued market pressure on the US coal industry was the overriding factor affecting developments in underground mining in 1986. An oversupply of coal in the spot market kept prices low throughout the year and caused a number of operations to close their doors. Operators stepped up their efforts to improve productivity at existing operations. They made technology advances and improved their relations with employees. A continuing market-related development during 1986 was the divesting of coal properties and operations by major oil companies, which were faced with economic pressures in both the oil and coal industries. Further increases in contract mining production resulted as some larger operators were unable to compete in a tough economic environment. Longwall mining is still seen by many as the technology that will provide the necessary productivity to remain cost-effective. But the number of active faces in the US declined in 1986, as reserves were depleted and economics forced some closures. At the first Longwall USA meeting in June, much attention was placed on improved technology, as electro-hydraulic controls for roof supports gained acceptance. Other recent developments include shearer initiation of roof supports, automatic horizon control for shearer drums, and collection and storage of machine data for predicting maintenance requirements. The government and academic communities continued their research on dust control at longwall faces. Jankowski, Kissel, and Daniel, (October 1986, Mining Engineering), gave an overview of progress in longwall dust control. And Mukherjee, Singh and Jayarman (November 1986, Mining Engineering), recommended design guidelines for improving water spray systems for dust control. Surface subsidence Increasing attention is being given to surface subsidence. This is primarily because of longwall mining and the Surface Mining Control and Reclamation Act. Improved methods of prediction of surface subsidence, especially computerized methods, are being continually developed. Mining engineering faculty at major universities such as Virginia are helping develop public policy and regulations concerning subsidence. As part of this effort, Unrug and Johnson identified major subsidence areas of Western Kentucky. Peng and Chen (February 1986, Mining Engineering), gave an overview of history and research of surface subsidence. And Elifrits and Aughenbaugh, (February 1986, Mining Engineering), discussed effects of moisture variations and overburden on subsidence. This research culminated in a Symposium on Surface Subsi¬dence at the SME 1986 Fall Meeting in St. Louis and the 2nd Workshop on Surface Subsidence at West Virginia University. Ground control in coal mining continued to be an item of major research interest. Some 30 papers were presented at the 5th International Conference on Ground Control in Mining at West Virginia University. And six sessions were related to coal mining at the 27th US Symposium on Rock Mechanics at the University of Alabama. At the 4th Annual Workshop, Generic Mineral Technology Center, Mine Systems Design and Ground Control emphasized efforts of the participating universities to improve ground control. Peng and Chiang summarized results of studying support capacity and roof behavior with longwall shield supports. And Unrug, Johnson, and Nandy analyzed the process of deterioration of shale roof in a case study of a room-and-pillar coal mine. The importance of geologic conditions in determining mining productivity is receiving increased attention in coal mine design in the US. Mullenex related, through case studies, the benefits to be derived through analyzing the depositional system of coalbeds as an integral part of mine design. Improved technology in this area was related by Lloyd, Semborski, and Stolarczyk. They discussed a case study of using radio imaging to indicate coal-seam discontinuities in advance of mining. Improved coal mining technology in general is being researched more heavily, to help improve US coal competitiveness. However, much of this research and development process has yet to be widely implemented. Equipment manufacturers are devoting more resources to development of continuous-haulage systems, mobile roof-supports, mine-monitoring systems, and predictive-maintenance systems using computers to extract machine data.

Jan 5, 1987

By Kendrick C. Hardcastle

Although the basic techniques employed in hydraulic pumping in open pit mining have been practiced throughout the better part of this century, only relatively recently have studies of' sufficient depth and scope been conducted to improve these techniques. This paper will point out the basic techniques involved and some of the more recently discovered data concerning hydraulic pumping, Inherent in all hydraulic transportation systems apart from the consideration of transportation cast, is the outstanding advantage of slurrying the matrix at the mining pit so as to provide a lengthy and thorough soaking and washing of the material while in the pipe line and thereby reduce the necessity for washing, scrubbing and other treatment in the beneficiation plant. This is quite important in view of the constant increase in demand for a cleaner product.

Jan 1, 1964

By A. Jahedsaravani, M. Massinaei, M. H. Marhaban, N. Mehrshad, M. I. Saripan

"It is well known that froth visual features reflect the operating conditions of the flotation process, so that being able to accurately obtain the froth properties is the most significant criteria to optimize and control this process. Froth segmentation is a useful procedure that can determine the bubble size distribution. Several algorithms have been proposed in this field, but marker-based watershed transform shows the best performance. In spite of this fact, the algorithm suffers from oversegmentation in cases when the flotation froth includes large bubbles along with small ones. In the paper, the marker-based watershed method is modified to prevent oversegmentation of large bubbles. The developed algorithm is validated using some froth images captured at different operating conditions, so the results indicate that the method can segment the mixture of big and small bubbles effectively.IntroductionFroth flotation is a widely used process for separating valuable from gangue minerals. Effective control of flotation circuits has a dramatic effect on overall performance of a mineral processing plant. In most flotation plants, process operators monitor the froth surface visually and make adjustments to process parameters based on their interpretation of the surface appearance and their idea of the appearance of an ideal froth. However, due to natural complexity of the flotation process, achieving optimal control is often not possible for human operators.In recent years, attempts have been made to control the flotation circuits using machine vision systems (Moolman et al., 1995; 1996a,b; Bartolacci et al., 2006; Kaartinen et al., 2006; Vanegas and Holtham, 2008; Aldrich et al., 2010). The froth bubble size distribution is the most significant control variable that reflects the operating conditions in a flotation machine. To date, a number of approaches have been proposed for bubble size measurement from froth images, including segmentation (Sadr-kazemi and Cilliers, 1997; Wang et al., 2003; Mehrshad and Massinaei, 2011), texture spectrum (Nguyen and Thornton, 1995), wavelet (Liu et al., 2005), an improved texture spectrum approach, a method based on binary images (Lin et al., 2008) and, finally, using interfacial morphological information (Yang et al., 2009)."

Jan 1, 2015

By P. H. S. W. Kulatilake

The presence of discontinuities strongly affects the mechanical and hydraulic behavior of rock masses. Joint geometry networks play a vital role in civil, mining, and petroleum engineering projects associated with jointed rock. The need for a realistic representation of joint geometry in rock masses has been recognized. The first part of the paper shows how to build three-dimensional stochastic joint network schemes and also shows how to perform validation studies for these schemes using joint data from the Stripa mine, Sweden. Due to the existence of complex joint patterns, mechanical behavior of jointed rock masses usually exhibit scale effects and an-isotropic properties. A correct understanding of the mechanical properties (strength and deformability) of jointed rock masses is important for designing and performance estimation of structures build in and on rock masses. Beyond a certain volume, the mass proper-ties of the rock may remain essentially constant with respect to the effect of joints. This minimum volume may be used as the element size to represent the equivalent properties of a statistically homogeneous rock mass volume which contains a significant number of joints. This volume may be termed as a "Representative Elementary Volume" (REV) and may be of great importance for engineering purposes. Investigations are underway at both the 2D and 3D levels to look into the possibility of establishing relationships between REV mechanical properties and joint geometry parameters. Recently developed joint geometry modeling schemes are linked with existing distinct element codes (both 2D and 3D) to create a stochastic/deterministic stress analysis approach in achieving the goal. Results obtained so far in this direction are presented in the second part of the paper.

Jan 1, 1992

By John W. Wilson

INTRODUCTION In the past, the cost and time required for the construction of shafts has played an important part in the planning of underground mines. For reasons that are discussed later, the economics and technology of shaft construction in the future can be expected to play an even greater role in the planning of new mines and the operation of existing mines. Indeed, the very feasibility of a proposed mining venture may depend on the cost and timing of the shaft requirements. The most commonly used shaft sinking methods used today for excavating vertical shafts are discussed and the need for new technology and methods emphasized. In one study by the U. S. Bureau of Mines, it was reported that the coal industry in the United States alone could require 170 to 190 new shafts per year on the basis of doubling current production by the mid 1980's or 70 to 90 shafts on a more moderate coal production expansion program. This study concluded that the attainment of the required number of shafts would be unlikely with the present shaft sinking resources and costs. In order to meet the requirements for shafts in the United States coal and metal mining industries, more efficient and speedier shaft construction methods will be necessary. Current shaft sinking methods are, in the main, labor intensive, and it is noteworthy that it is becoming increasingly difficult to attract the work force required to sink shafts conventionally. Because of this situation, some attempts at mechanization have been made to compensate for this ever-increasing scarcity of trained

Jan 1, 1976

By Duncan M. Lamb

Commercial computer "time-sharing" is a new and powerful tool for the engineer. It is a system of virtually simultaneous use of a digital computer by several individuals. Access to the computer is by means of a conventional teletypewriter which transmits over the regular telephone lines to the computer which may be located any distance from the user. Complex or repetitive computations can be programmed and the speed of computation is many times that which one can do with slide rule and desk calculator. The availability of such a commercial computer "time-sharing" system offered an opportunity to transform a tedious and time-consuming task into one that requires only a few minutes. Until the work of F. C. Bond produced widely accepted mathematical statements concerning the performance of grinding mills, the selection of the proper size equipment was done by comparison with similar operating equipment. Allis-Chalmers systematized Bond's work in a bulletin published in 1963 but the calculations are laborious and the final mill selection still required comparison of the calculated power draw with the power requirements listed in equipment catalogs. This was, however, a step forward from previous procedures. This paper discusses a rapid and simple method of determining the size and power requirement of overflow ball mills. A shared-time computer program has been developed which rapidly calculates and displays the physical dimensions, power requirements, grinding media size and quantity, as well as the important correction factors used. All of these data are calculated from input information which is usually available.

Jan 1, 1969

By HONGWEI YANG, Lili Zhang

Copper slag is mainly used in cutting tools, abrasives, asphalt pavement, road construction, and in the production of concrete as an alternative to sand and cement [1]. As a renewable resource, only about 15-20 percent of the slag is used for these applications, and the dumping or disposal of surplus unused slag results in waste of a certain amount of usable metal in the feedstock [2]. In this work, the oxidation behavior of copper smelting slag under nonisothermal condition is studied using data obtained by the thermogravimetric (TG) method, and the kinetics parameters and reaction mechanism of oxidation are determined. It provides a theoretical basis for the comprehensive recovery of iron resources in slag and the selection of reasonable slag-making conditions.

Oct 1, 2022

By R. A. Seitz

Although the role of the collector has long been thought to play a predominant role in coal flotation, recent investigations by the authors show that the frother plays an equally important role. These investigations have included extensive testwork in several coal preparation plants and in the laboratory. The factors which were investigated include the absolute level of collector and frother addition, the ratio of frother to collector additions, the type of frother, and the particle size distribution of the feed. Results from this testwork reveal strong interactions between these factors as well as the necessity of considering these factors in order to optimize the reagent regime.

Jan 1, 1987

By D. Brunner, G. R. Baiden, H. J. Yazici

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By Stephen Phillips, Luigi P. Gonano

Vertical circular shafts have been proposed for multiple access to high level nuclear waste deep geologic repositories. Shaft construction is a critical path item in the commissioning of a repository. Other constraints on the shaft design and construction criteria include the lack of design precedence for long term performance and the importance of minimizing rock and groundwater disturbance. A comparative evaluation of conventional and mechanized shaft sinking techniques is presented in the context of the particular geologic and design constraints. Technical and non-technical factors for blind drilling, blind boring, raise-reaming, drill-and-blast and ream-and slash methods are reviewed for typically "hard rock" and "salt" type repository sites. Appropriate shaft designs are developed, the suitability of each method to the particular requirements evaluated and construction costs and schedules determined. The explicit appraisal of the significant design factors for each method serves as a rational basis for the preliminary selection of the most suitable sinking technique for a particular set of site/design conditions.

Jan 1, 1983

By M. Sandin

According to the world bank1, the mining industry consumes up to 11 percent of global energy use. In comparison, 70 percent of mining projects from the six largest mining companies operate in water-stressed regions. To steer the direction of the process industries toward more sustainable practices, more than 40 governments have adopted a price on carbon. This measure includes additional taxes on the use of fossil fuels, trade programs, new standards for renewable energy, energy efficiency mandates, more stringent emissions regulation, carbon offsets, etc. This emphasis is also supported by investors shifting their priorities to reduce risk by focusing on long-term plans, including environmentally friendly operations. The metals and mining industry is at the core of the green energy mix and electrification of vehicles. This new trend creates an astronomical increase in demand for minerals. Under a 2-degree scenario, according to the latest analysis from the world bank, as new energy technologies continue to grow, it is expected that all minerals to double in demand, and the distribution of these materials will depend on their application. • Solar panels, will account for 87% of the aluminum demand, and more than 95% of silver • Wind turbines and geothermal plants will require 98% zinc and 64% titanium. • Solar and wind energy alone will demand more than 74% of the global supply of copper, and this is without considering wiring or other infrastructure to connect the grid • Battery storage accounts for 100% of the graphite and lithium demand. (Hund, 2020) • Other materials, such as nickel and steel, are also projected to more than double in demand as they are cross-technology minerals. These materials require a manufacturing process that is accountable for the emissions proper of the transformation process. It requires that these processes move from a hindsight mode focused on reporting to a forecasting mode based on run-time measurement of GHG emissions. This is a critical first step in companies realizing an economic return for doing the right thing for the environment and their communities.

Feb 1, 2023

By Pascale St-Germain, Michael Li, Lionel J. J. Catalan

The oxygen flux into water-covered reactive sulphidic tailings is required for evaluating the long-term performance and predicting the quality of engineered shallow water covers. This information can also serve as an input to the design of water covers for reactive tailings decommissioning. This paper describes some dissolved oxygen (DO) profiles recently measured in the field across the tailings/water interface and oxygen fluxes derived from these profiles. These fluxes are compared with previously reported flux values from similar field measurements. Techniques and pitfalls for measuring DO profiles and calculating oxygen fluxes are also discussed.

Jan 1, 2000

By John Brouwer

Through the use of good preventive maintenance procedures in which the work of both production and maintenance personnel is well-coordinated, production downtime can be drastically minimized, and costly repairs and interruptions in planned maintenance and production schedules can be eliminated. There had been some conflict in the past between production and maintenance people over the proper method of achieving maximum machine performance. The usual practice was to operate production equipment at maximum capacity for the longest possible time until breakdown occurred, and then make hurried repairs to get back into production. In most cases, these repairs involved unscheduled work and were thus performed inefficiently. Both production and maintenance have the same objective: to produce a quality product at maximum efficiency and at minimum cost. Preventive maintenance is a common tool available for both production and maintenance personnel to achieve this objective. Actually, one of the main objectives of preventive maintenance is to find any abnormal machine condition that may cause machine failure before a breakdown occurs. This makes it possible to plan and schedule maintenance work with the least amount of interruption and plan production volume with a higher rate of accuracy. Maintenance people prefer to perform this work on a scheduled basis and get away from the "crash" situation that accompanies breakdowns. They thereby increase the utilization of available manpower and machine time, prolong equipment life, and improve maintenance costs.

Jan 1, 1979

By Don U. Deere

The tunnel boring machine (TBM) can be a magnificent tunneling device under optimal rock conditions. Such ideal conditions would include good Rock Material Characteristics (compact, uniform; low to medium strength, hardness, and abrasiveness); good Rock Mass Characteristics (few joints and shears; unweathered); and good Geologic Environmental Characteristics (above groundwater level and moderate in-situ stress). Such idealized rock conditions would eliminate support problems, fallout at face and grippers, frequent cutter changes, and water problems. Daily advance rates of 50 m would be commonplace. Unfortunately, nature seldom provides the ideal geologic characteristics. The challenge to the geologist, machine manufacturer, and contractor is to provide equipment and procedures to best handle the adverse geologic features, once identified.

Jan 1, 1981

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

By J. B. Hadaway

The current limit to power transmission for grinding mills through one mill pinion is approximately 7,500kW. Above this power rating either twin pinion arrangements or Gearless drives are required. The SMTP concept was developed to overcome this limitation by using two pinions with a single large drive motor. The SMTP mill drive offers major advantages in capital cost and greatly simplifies plant layouts, while using an innovative adaptation of industry-proven single helical gearing. Through the use of a single motor, provision of variable speed drive is greatly simplified. The SMTP can also be used for significant power upgrades on existing mills.

Jan 1, 2001

By J. Dasher

Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to al low editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels.

Jan 1, 1991