Search Documents

By James A. Strosnider

INTRODUCTION The Metro Rail Project is approximately a 20-mile initial portion of Southern California's planned 150-mile transit network and will provide transit service to the dense population and employment centers within the Los Angeles regional core. The Southern California Rapid Transit District (SCRTD) has defined, as the first segment, a 4.4-mile five station rail line, which extends from the yard and shop area near Union Station to the Wilshire/Alvarado Station. Design packages are completed; utilities are currently being relocated; demolition is underway; early construction contracts have been awarded; and construction has started. This paper will describe the current status of the Metro Rail design and construction, after first briefly reviewing its history, objectives, and main components. PROJECT HISTORY The California State Legislature created the SCRTD in 1964 with a legislative mandate to design, construct, and operate a rapid transit system within the Los Angeles County area. To obtain the monies required to support this program, in June, 1974, Proposition 5 was passed by a solid majority, allowing a portion of state gasoline taxes to be used for rapid transit development. This measure provided a local source of funds for SCRTD to begin its rail rapid transit development program in Los Angeles.

Jan 1, 1987

By B. M. Davis

The Colosseum Mine is within the Clark Mountain mining district located approximately 72 km (42 miles) southwest of Las Vegas. Nevada in San Bernardino County, California. Gold mineralization at the Colosseum Mine is hosted in two 150 m by 210 m (500 ft X 700 ft) interconnected. rhyolitic intrusive breccia pipes that intruded Precambrian crystalline basement rocks and over-lying Paleozoic marine sedimentary rocks. Sub-sequent erosion (de-roofing) of all of the Paleozoic section and a portion of the Precambrian section has exposed the pipes to the present level (probably a significant depth in the original breccia pipe system).

Jan 1, 1989

Accidents that resulted in 16 deaths in three West Virginia coal mines, two in Kentucky and one in Utah have government and industry re-evaluating current safety regulations. Even though U.S. mines continue to improve on their safety records, the deaths reminded the industry and state and federal agencies that mining remains a dangerous business. Even so, data from the U.S. Mine Safety and Health Administration (MSHA) show that new technologies and a highly trained workforce has allowed the nation’s coal mines to increase production while providing safer workplaces. Since 1970, coal production at U.S. mines has increased by about 83 percent. During the same period, fatal injuries have fallen by 92 percent. And more than half of the U.S. coal mines operate each year without a lost-time injury. In 2005, there were 22 deaths in U.S. mines, a record low.

Jan 1, 2006

By Rick McGregor, David Blowes, Mike Choi, Ralph Ludwig

The oxidation of sulfide minerals at an ore transfer location in Western Canada has resulted in widespread contamination of underlying soil and groundwater. The oxidation of sulfide minerals has released sulfate [SO,] and heavy metals including cadmium [Cd], copper [Cu], nickel [Ni], lead [Pb], and zinc [Zn] into the groundwater. A compost-based sulfate-reducing reactive wall was installed in the path of the plume in an attempt to reduce the potential impact of the heavy metals on a down-gradient marine inlet. Monitoring of the reactive wall over a 21-month period has shown that Cu concentrations decrease from over 4000 ug/L to less than 5 ug/L. Cadmium, Ni, Pb, and Zn concentrations also show similar decreases with treated concentrations generally being observed near or below detection limits.

Jan 1, 2000

Introduction The art of ripping has been around since the Romans built the Appian Way, but only in the last decade has ripping emerged as a close competitor with drilling and blasting in breaking up heavy rock formations. That is not to say ripping is as effective in every case, or even applicable in all cases, but it does provide a cost efficient option in many situations-if the optimum ripping techniques are used. Originally designed only to loosen hard pan, the ripper has evolved into a powerful tool, its capability increasing as the weight and horsepower of tractors increased. The tractor-mounted ripper extended the range of ripping because of the additional weight it brought to bear on the ripper tooth. Tandem ripping added the weight and power of a second tractor, extending the rippability range even further. Of course, the use of ripping depends on the type of material to be ripped. Not all rock can be ripped. Determination of rippability-an art in itself-is often inconclusive but there are certain universal principles that can be considered in the first step toward optimizing ripping techniques. Each of the three basic rock types, igneous, sedimentary, and metamorphic, exhibits characteristics that bear on rippability. Igneous rocks are the most difficult to rip because they lack the stratification and cleavage planes essential to ripping hard rock. Sedimentary rocks are generally the most easily ripped since they are built of layers differing in material, texture, color, and thickness. Metamorphic rocks vary in rippability with degree of lamination or cleavage caused by transformation from pre-existing rock. The condition of rock also affects its rippability. Although sedimentary rocks offer the best opportunity to rip and igneous and metamorphic the least, decomposed granite and other weathered igneous and metamorphic rock often can be ripped economically. Little or no trouble is encountered with hardpan, clays, shales, or cemented gravel. Likewise, highly stratified or laminated rocks offer good possibilities for ripping. However, thicklybedded rock formations generally must be drilled and blasted. The physical characteristics that favor ripping may be summarized as follows: • Fractures, faults, and planes of weakness of any kind; • Weathering, resulting from temperature and moisture changes; • Brittleness and crystalline nature; • High degree of stratification or lamination; • Large grain size; • Moisture permeated clay, shale, and rock formations; and • Low compressive strength. Ripper Types A second fundamental to optimal ripping is choosing the right equipment for a particular job. There are three types of rippers-the hinge, the parallelogram, and the adjustable parallelogram. In the hinge ripper the linkage carrying the beam and shank pivots on a fixed point at the rear of the tractor. The resulting arc from up and down movement causes up to 30° differential in the tip-ground angle. Thus, the tooth angle changes as it enters and proceeds to ripping depth. The parallelogram ripper's linkage maintains the same tip-ground angle regardless of tooth depth. This type of ripper has advantages over the hinge-type when ripping above maximum depth, but does not provide the aggressive tooth angle necessary for hard-to-penetrate materials. The adjustable parallelogram combines the benefits of both the hinge and the parallelogram rippers. It has the additional benefit of being able to vary the tip angle to the optimum angle of penetration. It can also be adjusted while moving, for the optimum ripping angle in any material. Several other factors that are important in selecting the right ripping equipment are down pressure available at the tip of the ripper, tractor flywheel horsepower, and the tractor's gross weight. Down pressure at the tip determines whether ripper penetration can be obtained and maintained. Flywheel horsepower rating determines whether the tractor has the power to advance the tip. The tractor's gross weight determines whether the tractor will have sufficient- to use the horsepower. The best ripping procedure depends on the job's actual conditions. While conditions, vary, it is still possible to apply certain proven techniques to a typical ripping situation. Caterpillar Tractor Co.'s Handbook on Ripping says optimum ripping efficiency can be realized if-before actual ripping begins-these questions and answers are considered.

Jan 1, 1983

By Kaixi Jiang, Chaozhen Zheng, Shuchen Qin, Hao Ma, Yufang Wang

The study investigates the behaviors of zinc and iron in neutralized residue during pressure and hot acid leaching. It examines the effects of temperature, acidity, leaching time, and oxygen partial pressure on zinc extraction. The results indicate that the acid to zinc mole ratio is crucial for the extraction process, with a zinc extraction rate reaching 98.0% under optimal conditions.

Feb 14, 2022

Using mines in Canada, Boart Longyear, a leading provider of drilling services and products, has put its Stage 3 Coring Bit to the test and each time the bit has passed the test with great success. After more than a year in the field at a major mine operation in Sudbury, Canada, the Stage3 coring bit broke life records to become recognized as the most productive design in the industry. In addition to the proven advantage seen in regular bit life increases of as much as 300 percent in some cases, the design is quickly being recognized for its cost-saving operational impact. In Sudbury, the mine operation realized actual cash savings of more than C$45,000 within an eight-month period by making the switch to Stage3 bits. For years, the Sudbury Basin team has relied on the Alpha Extended Crown bit with the Express Waterway geometry option, ordering approximately 500 units per year. This 07 COM ECEX configuration performed well in medium-hard, non-abrasive to ultra-hard, non-abrasive formations with an average bit life of 150 m (490 ft). While satisfied with the performance of the Alpha Ex-tended Crown, the team agreed to put the new Alpha Stage3 to the test. Boart Longyear?s field engineers supplied five drill sites with Alpha Stage3 bits in a 07 COM configuration. After thoroughly testing the Stage3, the results were clear. Even with the well-known performance and versatility offered by the previously preferred configuration, the Stage3 set a new standard of bit performance. The new bit maintained its cutting edge for up to three times longer than the Alpha Extended Crown, a significant performance increase when compared to the 07 COM ECEX.

Jan 1, 2009

By Paul Eimon

In the world of minerals exploration, computer-oriented data storage and retrieval methods are being talked about, studied and researched. The goal is to facilitate the recording, collating, indexing, recovery, and analysis of mineral deposit-prospect data. A survey has been made of the various report forms, suggested outlines, and computer coding forms that are currently used in mineral exploration to index and/or describe mineral deposits and prospects. These forms have a number of common characteristics: location, commodities, type of deposit, host rock, etc. Such basic mineral deposit-prospect "data units" are part of most exploration programs. "Data units" may be comprehensive bound published descriptions of mines or mining districts or 3x5 file cards or elaborate computer coding forms being developed in Canada. Initial attempts to develop computer-oriented information systems have run into the same roadblock: the lack of a body of organized, processible data describing the basic qualities of mineral deposits and prospects. To solve this problem, international committees are considering coding forms, world-wide semantics, and rules or standards for data collection and description. It appears that mistrust and lack of understanding of the computer; fear of loss of proprietary information; and disagreements over terminology are distorting the picture of what has to be done if the mining industry is to grow into more meaningful information systems for mineral exploration.

Jan 1, 1969

By Malcolm Ross

Asbestos crystallizes within rock formations undergoing intense deformation characterized by folding, faulting, shearing, and dilation. Some of these conditions have prevailed during formation of the taconite iron ore deposits in the eastern Mesabi Iron Range of Minnesota. This range includes the Peter Mitchell Taconite Mine at Babbitt, Minnesota. The mine pit is over 8 miles long, up to 1 mile wide. Fifty three samples were collected from 30 sites within areas of the pit where faulting, shearing and folding occur and where fibrous minerals might occur. Eight samples from seven collecting sites contain significant amounts of ferroactinolite amphibole that is partially to completely altered to fibrous ferroactinolite. Two samples from two other sites contain ferroactinolite degraded to ropy masses of fibers consisting mostly of ferrian sepiolite as defined by X-ray diffraction and TEM and SEM X-ray spectral analysis. Samples from five other sites contain unaltered amphiboles, however some of these samples also contain a very small number of fiber bundles composed of mixtures of grunerite, ferroactinolite, and ferrian sepiolite. It is proposed that the alteration of the amphiboles was caused by reaction with water-rich acidic fluids that moved through the mine faults and shear zones. The fibrous amphiboles and ferrian sepiolite collected at the Peter Mitchell Mine composes a tiny fraction of one percent of the total rock mass of this taconite deposit; an even a smaller amount of these mineral fragments enter the ambient air during mining and milling. These fibrous minerals thus do not present a significant health hazard to the miners nor to those non-occupationally exposed. No asbestos of any type was found in the mine pit. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Amphibole; Reserve mining; Tailings; Mesabi iron range; Mineral fibers

Jan 1, 2007

By S. S. Mauney

Natural and synthetic colors are used in almost every facet of daily life as a means of communication and expression. Natural ochres, umbers, hematites and magnetites were once used in their crude or semiprocessed state for their pigment value in construction products and low-end coatings applications. In recent years, though, they have yielded to synthetically produced iron oxides for more sophisticated products. Today, through innovative mining processing and marketing techniques, natural iron oxide pigments are once again gaining strong inroads into products and markets requiring precise chemical and physical characteristics. With the focus on environmental consciousness and resource conservation, value added natural iron oxides provide an economical and responsible alternative to color needs.

Jan 1, 1995

By J. R. Blair, D. P. Lindroth, W. R. Berglund, R. J. Morrell

The objective of this US Bureau of Mines (Bureau) research was to determine the technical feasibility, principles and effectiveness of a combination energy method for drilling and cutting hard rocks. Experimental test results of microwave heating and drilling in basalt and granodiorite are given. The experiments were performed with pilot-scale, commercially available equipment employing microwave energy at a standard industrial frequency of 2.45 GHz. The data indicate that penetration rates, well in excess of the state of the art, are possible.

Jan 1, 1993

By G. T. Adel

This paper presents the highlights of a general-purpose simulator for mineral processing plants that is being developed at the University of California, Berkeley. The state-of-the-art structured design methodogy based on a top-down design approach is being used to construct a modular and completely structured simulator such that it is independent of the unit operation models and routines. The simulator provides for two levels of operation allowing prebuilt or user-built simulation flowsheets depending upon the degree of computer knowledge expected of the user. The philosophy used in designing this simulator appears to be unique in the field of flowsheet simulation. The paper also includes a mini-example demonstrating the usage of the simulator.

Jan 1, 1982

By J. W. T. Ropkins, D. Allenby

The paper describes a technique by which large concrete boxes are unobtrusively inserted beneath existing highway and railway infrastructure to form new subways, culverts and under-bridges, thus avoiding the inconvenience and costs of disruption to traffic associated with traditional cut and cover techniques. A series of project examples, undertaken in the United Kingdom and United States, are used to illustrate the design and construction of the box structures, together with the technology required to control ground disturbance in the tunnel face and around the box, and the jacking systems necessary for box installation.

Jan 1, 2003

By Frank Matter

Production of ultrafine powders of industrial minerals has been a problem in the past. In recent years new wet and dry grinding stirred ball mill systems have emerged which have been commercialized Two such systems are the TRZK mill with double step air classifier for dry grinding and the NRZK mill for wet grinding The primary features of these mills are feed entering from top and the product along with the grinding media leaving from the bottom, and a media separation and recycle system A detailed description of the NRZK mill for grinding coal is presented

Jan 1, 1983

By M. K. Gangal, E. D. Dainty

CANMET/MRL has been contributing to an industry/government program to assess the quality of air in mines, and improve the working environment for Canadian miners. The ultimate aim of this program is to recommend a sampling methodology and appropriate concentration limits for both the soot (diesel particulate matter - DPM) generated by diesel equipment, and respirable combustible dust (RCD) as measured underground. The program was conceived by the Canadian Adhoc Diesel Committee, which consists of representatives from seven major Canadian mining companies, three provincial inspectorates, one union representative, two manufacturers of diesel equipment, and CANMET, a Federal Canadian research agency. This paper describes the modification and laboratory confirmation of an existing methodology for the sampling and analysis of DPM/RCD, including: sampling problems, filter selection, filter efficiency, DPM size distribution, the approximate performance of fractionating devices, and it reports the results of current ambient measurements of exposure levels in Canadian underground mines. Because of the concern about the health impact of DPM/RCD on mine workers, North American agencies are in the process of establishing limits for these aerosols. So far, the Province of British Columbia is the only jurisdiction in North America to legislate the maximum exposure level of RCD in its underground mines, i.e. 1.5 mg/m3 interim level recommended by the Adhoc Diesel Committee. It has also recommended the use of the CANMET/ADHOC RCD sampling protocol.

Jan 1, 1993

By W. Chae

The influence of solution ionic strength (IS) and electrolyte valence on the flotation behavior of malachite has been investigated. The microflotation tests were conducted over a range of solution IS (1?300 mM) at a constant speed (340 rpm), pH (9.5), flotation time (10 min), and sodium oleate dosage (5.3×10-7 moles/g). The size of malachite ranged from 45 to 53 µm, and two different types of electrolytes (NaCl and CaCl2) were employed. Electrophoretic mobility was also measured over the same IS range employed in the microflotation study. Overall, strong coupled effect of solution IS and ion valence was observed. Specifically, the flotability of malachite increased with increasing IS in the presence of monovalent cation (Na+) while the flotability increased up to 30 mM and decreased with increasing IS in the presence of divalent cation (Ca2+). Notably, the flotability of malachite was greater with the presence of Na+ compared with Ca2+ under high IS conditions (IS>30 mM). Consistent trend for Na+ versus Ca2+ was observed from the flotation results with different SO dosages. The characterization and flotation results suggested that the trend was likely attributed to the increased unfavorable interaction between malachite and bubble via the charge reversal of bubbles and malachite at higher IS in the presence of Ca2+.

Feb 27, 2013

By Robert E. Moore

Investigators have attempted to develop lime refractories on a scale for broad applications in the metal and ceramic industries for several decades. There was a flurry of activity in the early to mid-fifties but no commercial developments were forthcoming. The literature of that period yields little information on plant trials. A major factor suppressing past interest in lime has to have been the high success with the application of magnesic and dolomitic materials. These materials, usually tar-bonded or impregnated, have become the refractories success story of the past two decades, especially in BOF applications. It is safe to say that their development and application has essentially plateaued, and that work today is focussed on finding cheaper paths to produce MgO-based refractories. For example there are efforts underway to extract MgO from mineral magnesite and to combine natural dolomite with MgO1. Beginning in the late sixties, rather intensive research began on the development of CaO brick, especially in East and West Germany, in Poland, and other communist bloc satellites, 'and also in Italy and Spain. One speculates that the motivation was a regional shortage of good magnesia and dolomitic material. Of course, There has always existed the prospect of cost savings should it be possible to use raw limestone as the starting material. Quite a large literature has appeared treating of these developments which in the early seventies had already reached full plant scale trials and uses. Some of the directions followed in the research have led to novel methods of brick manufacture.

Jan 1, 1985

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein-type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed and to improve the metallurgical efficiency of 'the concentrators to improve the production quality and quantity of concentrates.

Jan 1, 1992

By Kumar Vikram

Rich reserve of prime quality limestone in east khasi hills of India and abundant quantity of low-cost fuel (Natural Gas) in Bangladesh made Lafarge Surma cement limited a joint venture company of Lafarge France and Cementos Molins Spain to envisage an integrated cement plant at Chatak District-Sylhet) a bordering town of Bangladesh. Since April 2006 the single flight 17 km Long Belt Conveyor (LBC) built by M/S Larsen & Toubro Ltd. (L&T), ECC Division an engineering and construction company of India, is feeding limestone/shale to the Lafarge Surma cement plant. This engineering marvel was created on a turnkey basis with technology support of M/S Aumund France

Jan 1, 2008

By W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999