Search Documents

By L. Alan Weakly

This paper was presented at the ‘17th U. S. Symposium on Rock Mechanics’ on August 29, 1976, at Snowbird, Utah, at the SME-AIME Fall Meeting on September 1, 1976, at Denver, Colorado, and at the Polish-American conference on Ground Control in Room-and-Pillar Mining on August 7, 1980 at Southern Illinois University, Carbondale, Illinois. Introduction The purpose of this paper is to present a viable method of reinforcing rock pillars by utilizing fully grouted reinforcing steel and a cement- fly ash mortar. Although the fully bonded bolt concept is not new as exemplified by the present widespread use of resin bolts within United States mines and by the use of cement grouted reinforcing used as back pins in the Kiruna Iron Ore Mine in northern Sweden, (1)(2)the method of stabilizing mine pillars with fully bonded reinforcing is new. This method, called the "grout-rebar system", was first incorporated at St. Joe Minerals Corporation's Fletcher Mine in December of 1972. The system was used on an emergency basis before extensive research on the mechanics of the system could be completed. Since Decmeber of 1972, however, approximately 206 pillars have been reinforced at Fletcher and the system is currently being used on a regular basis at two other St. Joe mines and at two competitor mines in the area. Basically, this paper is a case study of the efforts, research and results of utilizing the grout-rebar system, on a selective basis, at the Fletcher Mine. In addition to information about the system, this paper will explain in detail the three rock mechanics instruments developed by St. Joe and used to measure and monitor rock movement to validate the group-rebar system.

Jan 1, 1982

By Betty Gibbs

The Ore Body Modeling and Mine Planning Worshop, sponsored by the Society for Mining, Metallurgy, and Exploration, Inc. (SME), was held Feb. 22-24, 1991 before the SME Annual Meeting and Exhibit in Denver, CO. More than 40 people from mining companies, government agencies and universities attended. Eight vendors of integrated ore body modeling and mine planning software attended and presented the results of problem sets given before and during the workshop. They were: [ ]

Jan 1, 1991

By James R. Boulton

Fire detection using Carbon Monoxide sensors is based on the assumption that a rise in the level of Carbon Monoxide in the atmosphere over a fixed, predetermined ambient level is indicative of a fire. The method is simple, reliable, and effective in those mines where the only source of CO is from undesired combustion. Ambience for this purpose is defined as that level of the gas that is present on a day to day basis whose source is not a fire. In a diesel powered mine the level of CO can and does vary so widely from hour to hour and minute to minute that the selection of a predetermined, fixed level represents a compromise between sensitivity and reliability. The compromise is a best of both and worst of both situations and the computer system often resembles the little boy who cried wolf instead of a state of the art early fire monitoring and detection system. Cyprus Coal personnel have developed method of determining the ambient level of CO in the atmosphere on a real time basis and using that dynamic ambient level to determine whether or not a fire exists in the mine. The method has been given the name of Wave Trend Crossing.

Jan 1, 1991

By Paul M. Godlewski, Gerry Millar, Harvey W. Parker

Recently, over 70 railroad tunnels in the western USA have been enlarged and rehabilitated "live track," utilizing modern excavation and lining methods, in most cases to clear the larger double-stack container cars. This paper presents the general conditions of the tunnels and the technical aspects and costs of the rehabilitation of approximately 40 kilometers of tunnels, which range in length from a few hundred meters to 13 kilometers. Concrete-lined tunnels were rehabilitated by grouting and rock bolting, while unlined or timber-supported tunnels were relined with shotcrete and rock bolts. High output lining methods were required because of limited track time. Enlargement has been accomplished primarily by carving notches out of the concrete linings with a roadheader, or occasionally with saws. Unlined tunnels were enlarged by drill-and-blast or roadheader excavation.

Jan 1, 1991

By David C. McLean, Peter Penner, Martin de G. Salter

The Rogers Pass Project for C.P. Rail includes a 14.7 km tunnel and an 8.5m diameter concrete lined ventilation shaft to a depth of about 335m. The shaft collar is in bouldered water bearing glacial till to a depth of about 95m. Initial excavation in the overburden was with the aid of dewatering wells. When ground support problems arose the excavation was completed by a two stage freeze programme. Freeze holes were drilled from the shaft bottom. This most unusual method was successful in overcoming the difficulties safely and efficiently. The remainder of the shaft was sunk and lined conventionally. Finally, a central dividing wall was poured by jump forming from the bottom up. The wall was completed to a high standard at up to about 20 vertical metres per day.

Jan 1, 1989

By C. L. Karr, D. L. Meredith, D. A. Stanley

The U.S. Bureau of Mines is currently investigating ways to combine the learning capabilities of genetic algorithms with the process control capabilities of fuzzy logic. Fuzzy logic has been successfully used for controlling a number of physical systems. However, the selection of acceptable fuzzy membership functions has generally been a subjective decision. In this paper, high-performance fuzzy membership functions are learned using a genetic algorithm, a search technique based on the mechanics of natural genetics. The membership functions learned by the genetic algorithm provide for a more efficient fuzzy logic controller than the membership functions selected by the authors for the liquid level system considered. The approach to developing genetic algorithm-based fuzzy logic controllers is demonstrated on a liquid level controller.

Jan 1, 1990

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

By Pierre J. Goossens

Since Guild 1 and Snelgrove 2 attracted our attention to the relationships between certain endogenic ore deposits and plate boundaries, an abundant flow of papers appeared in the metallogenic literature concerned with this problem and its application to mineral exploration. Some of the papers only speculate with the formation of specific type of ore deposit 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 Other papers are more concerned with genetic and structural relationships between plate tectonics and mineralization 13, 14, 15, 16, 17, 18, 19, 20 They are philosophical, in that they are generalized and refer to no specific area. Yet it is true that a large part of the world mineral potential is concentrated at the convergence of oceanic and continental plates, for example, around the Pacific. Therefore, the interaction of two plates by either subduction, obduction or slippage likely has an important role for the genesis and/or the (structural) control of these "orogenic" ore deposits. If subduction is the driving mechanism for the generation of igneous rocks 21, 22 and endogenic ore deposits 18, volcanic activity and the nature of volcanic products certainly are the major geologic processes and events to be tested. Fonteilles 23 and Alsac 24 have already emphasized the important relationship between mineralization and the talc-alkaline affinity of the volcanics. The Andean orogen is one of the best areas for testing such genetic relationships. Rich and varied endogenic and volcanogenic ore deposits occur there and plate interaction is still active.

Jan 1, 1975

By Eung Ha Cho, Olufemi Olajide

A laboratory study of dense-medium cycloning with Redstone seam coal has been conducted. The investigation was performed using a 203 mm (8 inch) Heyl-Patterson dense-medium cyclone. Two underflow orifices of 31.8 mm (1.25 inch) and 44.5 mm (1.75 inch) in diam were used. The effects of feed pressure and particle size were determined on the cycloning performance. In addition, the cyclone performances with coal-rich and refuse-rich samples were also investigated. The results of the experiments were analyzed using basic hydrodynamic principles. The increase in the feed pressure increases the specific gravity of separation (defined as the specific gravity of a particle which has an equal chance of reporting to either the overflow or underfow) for both underfow orifices. The specific gravity of separation increases as the particle size decreases with the smaller underflow orifice. However, an opposite relationship has been observed with the larger under flow orifice. The separation becomes sharper with the smaller under flow orifice than with the larger underflow orifice especially for fine material. Also, the separation becomes sharper with an increased feed pressure for a coal-rich sample. However, this effect is less significant for a refuse-rich sample. This means that a high feed pressure is required for a coal-rich sample to maintain a good separation. It also means that applying a high feed pressure provides a good separation regardless of the type of feed coal in terms of ash content in the solid.

Jan 1, 1990

By H. H. Richards, Ray L. Tobie, L. A. Thomas

GENERAL DESCRIPTION Since the beginning of operations, with the exception of a small tonnage mined by slushing, ore extraction has been by full gravity caving. Formerly, a checkerboard sequence of block undercutting was followed with the even-numbered blocks in one panel and the odd¬numbered blocks in the adjacent panel being mined. As these blocks were depleted, the intermediate or pillar blocks were mined (Fig. 1). Following this checker¬board, the mining sequence went through a number of changes, finally evolving into diagonal retreat panel cav¬ing by blocks (Fig. 2). The numbers in Fig. 2 indicate the sequence in which blocks were undercut. Gaps in the numbering sequence indicate undercutting on the level outside the illustrated area. Geology The ore body is a low-grade deposit of chalcopyrite mineralization disseminated throughout structurally weak, highly fractured, strongly altered granitic host rocks. It takes the shape of a gently dipping elliptical cylinder consisting of an ore shell of variable thickness surrounding an interior waste core. Major and minor axes of the mineralized cylinder are 1524 m (5000 ft) and 762 m (2500 ft), respectively, and length approximates 2438 m (8000 ft). Ore is sufficiently fractured to break readily into medium-coarse size. The igneous rock complex containing the ore body is covered by a wedge-shaped blanket of Tertiary con¬glomerate which was brought into place by faulting along the major regional structure of the San Manuel fault. Thickness of the conglomerate cap varies from only 9 m (30 ft) at the east end of the ore body to more than 610 m (2000 ft) at the west. Structurally, the con¬glomerate is much more competent than the igneous host rocks and, when caving, it breaks into massive chunks. Conglomerate boulders seen in drawpoints underground are very coarse. The total rock column over the initial mining area of the 1415 grizzly level was 354 m (1160 ft) of which 122 m (400 ft) was ore, 79 m (260 ft) was leached igneous capping, and 152 m (500 ft) was conglomerate above the San Manuel fault. Diamond Drilling: From 4572 to 7620 m (15,000 to 25,000 ft) are drilled annually from underground workings to delineate the ore body. MINE DEVELOPMENT Haulage Level In the south or main ore body (see Figs. 3-6), with the exception of the draw and transfer raises, all the extraction openings are concreted (Seaney and Tobie, 1965). The haulage panel drifts, which are 18 m (60 ft) below the grizzly drifts, are first driven with pre¬concrete ground support. The drift, which has an arched section, then is concreted using mobile collapsible steel tunnel forms. The haulage drifts leading from the pan¬els to the hoisting shafts are not concreted. After the panel drifts have been concreted, the raise stations from which transfer raises will be driven are constructed and the raise-station ore-drawing chute is installed. The chute is prefabricated of A-36 steel with undercut guillo¬tine gates made of abrasion-resistant 2.5-cm (1-in.) steel plate powered by 20-cm (8-in.) air cylinder installed on each side of the raise station. Transfer Raises The transfer raises are lined with 15 x 20-cm (6 x 8-in.) cribbing and are 1.22 m (4 ft) in the clear. Each cribbing is protected from wear by a high carbon steel angle which is nailed onto the cribbing. The transfer raises are driven from each side of the raise station on an angle of 1.1 rad (63°). Each raise con¬sists of a main and a backover branch. The transfer¬raise driving crew consists of two men working one shift only. Grizzly Drifts After the transfer raise reaches the grizzly level, the grizzly drift can be driven. The grizzly drifts are spaced at 10.6-m (35-ft) centers and are driven parallel to the long axis of the ore body (see Fig. 2). This drift is driven by a two-man crew working on one or more drifts at a time using feed-leg machines. The eight grizzlies in the 42.7-m (140-ft) long drift are spaced at 5.3-m

Jan 1, 1982

By Jeffery Leavy, Ken Davis, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) is a United States Department of Energy facility located in southeastern New Mexico. It is designed for the safe disposal of transuranic radioactive waste in deep geologic salt beds. Westinghouse TRU Solutions, LLC, the managing and operating contractor, undertook a project to simulate the processes at WIPP in order to identify bottlenecks and optimize available resources. The activities simulated in the model included the receipt, processing and disposal of radioactive waste underground, the mining of new areas for future waste disposal and the transportation of salt out of the mine. The complexity of the processes and the interactive requirements between processes required the use of advanced modeling techniques. The simulation model includes a huge number of locations and path network node points, with movement to and from the locations controlled using parameters rather than explicit routing. Information for the timing and sequence of the mining and nuclear waste emplacement operations is brought into the model via spreadsheets. Arrays in the simulation model keep track of past and future events that occur. Routing to the multiple possible positions in the underground mine is done using attributes, and system functions within ProModel in order to allow for a highly flexible sequence of planned events and to reduce the level of effort in creating the ProModel processing. Considerable use of subroutines in the simulation model is utilized for parametric decision-making that is repetitive. This presentation describes the modeling techniques used to accurately simulate the surface and underground operations. The surface and underground operations are considerably different, thus they will be treated in their own sections.

Jan 1, 2002

By N. S. Tanious

The accuracy of vibrating wire stress meters has been questioned by various users in the mining industry. During an in situ coal pillar study, a laboratory evaluation program was developed to determine whether stress meters could produce reliable measurements in coal. More than $0 stress meters were tested for accuracy, repeatability, effects of setting pressure, and the concept of using a single curve for interpreting the stress-meter data. The testing medium was lucite, a material with a modulus of elasticity very similar to coal. The evaluation demonstrated that the stress meters did provide repeatable measurements, but that accuracy was lacking when the recommended interpretation technique was used. Therefore, a new technique was developed that required all stress meters to be calibrated in the laboratory before use in the field. This new technique reduced the average error to typically less than 10% and, in the worst case, to below 15%.

Jan 1, 1988

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By Hassan Madani, A. Malek Mohammadi

Dorreh barite mine located in the central part of Iran is one of the largest barite mines, in the country. The mine is subdivided into three blocks, which are called block 1,2,3 according the barite quality. In the central part of each block, a heavily concentrated grid of exploratory drill holes have been drilled and the reserves of area was calculated based on these holes, some years ago. It was decided to compute the reserve of the area by geostatistical methods, in the form of an M.Sc. project. In order to study the area, three regionalized variables including density, thickness and density-thickness (accumulation) was studied and the spherical variograms were fitted to these variables. These models were evaluated by cross-validation method. The optimized block size was chosen in order to compute the reserves by kriging method. The reserves of explored parts of each block of mine was calculated and the results were extended to the whole area of the blocks. The reserve of the explored parts and the total reserve of the area were calculated to be 96,000t and 1,670,000t respectively.

Jan 1, 1996

By M. A. Sochocky

Rod mills were developed, as a logical substitute for the rolls crusher when larger tonnages had to be handled, on a continuous basis. Today, with even larger tonnages to process, the trend is to install larger equipment, automate the plant and develop the highest availability possible, in order to cut costs. The rod mills, because of design limitations in size and speed 1'2, are not able to meet these new requirements. The autogenous mill was a timely development and serves as an excellent alternative for ores that are suitable to this type of grinding. When ores are not amenable to autogenous grinding, selection of a flowsheet is dictated by liberation characteristics and unit operations to be used for mineral recovery.. The following alternatives are available: (a) Multiple rod mills, capable of drawing no more than 2000 HP each, followed by ball mills. (b) Gyradisc crusher followed by two stages of ball mill grinding.3 (c) Tertiary crushing followed by closed circuit single stage ball mills grinding to approximately -100 mesh, as in the copper industry. (d) Tertiary' crushing followed by two-stage, ball milling. Each stage will operate in closed circuit with either screens or cyclones. It is this last alternative, particularly as it

Jan 1, 1972

By Joseph Peterson, Alexander May

The Bureau of Mines used geochemical modelling computer programs to characterize a site containing lead slag generated by a lead processing facility. Tests for toxic elements by the U. S. Environmental Protection Agency (EPA) extraction procedure showed that all elements except lead were in compliance. Concentrations for lead ranged from 28 to 30 ppm. However, analysis of water samples from monitoring wells resulted in no lead concentrations that exceeded the National Drinking Water Standard. A discussion of a computational program to calculate concentrations of lead species and several other ions is presented.

Jan 1, 1991

By Michael B. Gilbert

The Woodbury L-73 Tunnel involved the design and construction of a 96-inch tunnel driven through 8,080 lf of very difficult ground conditions. Anticipated ground and groundwater conditions consisted of potentially flowing silty sand with cobbles and boulders, mixed face of sand and sandstone and full face of the St. Peter Sandstone. Actual conditions were similar, although the quantities did change from bid quantities. This paper presents the approach used for development of the GBR regarding risk management. The means of arriving at a fair compensation for variances from the baseline values to address the actual encountered tunneling behavior of the soil, boulder count and its effect on production rates are presented.

Jan 1, 2008

By D. DeGagné, E. De Souza, J. F. Archibald

A comprehensive survey of minefill practices in underground mines in Canada has been conducted. The survey was designed to cover the entire filling operation for individual mines from feed to the preparation plant, to underground transportation, and to stope placement. The questionnaire examined such areas as mining method utilized, the purpose of backfilling, backfill formulations, including binding and chemical additives, slurry properties, transportation parameters, stope preparation procedures, backfill placement properties, fill instrumentation, and costs. This paper presents the current state of backfill usage in Canada, identifies trends in minefill practices and provides mine operators with an updated database to compare their own practices with modern trends throughout the industry.

Jan 1, 2001

By T. Kelly

The post-apartheid South African government has instituted a new minerals policy. As part of the new policy, minerals rights are now held by the national government, not as private property. In addition, the national government desires to see a greater participation of all South Africans in the corporate mining arena. At the same time, the national government has adopted a policy of a strong monetary unit compared to the U.S. Dollar. The combination of these tow policies has led to changes within the platinum mining industry.

Jan 1, 2004

By G. G. O. O. Uwadiale, M. A. Kollere, M. A. U. Nwoke

Birnin Gwari and Alawa graphite deposits were upgraded by flotation. Using 0.5 kg/t kerosene and 0.25 kg/t sodium silicate, flotation concentrates grading 90.7% and 88% Cg with recoveries of 86.2% and 84% were produced from Birnin Gwari and Alawa graphite samples, respectively. The combination of 0.5 kg/t kerosene, 0.2 kg/t pine oil and 0.25 kg/t sodium silicate yielded high-grade graphite (92.3% Cg) with a recovery of 83.9%. Flotation with refined rubber nut oil and kerosene, at a 1:1 ratio, produced a concentrate grade of 86.3% Cg with a recovery of 90.4%. With acid leaching of the flotation concentrate, a high-grade graphite concentrate containing 98% Cg was produced.

Jan 1, 1998