Search Documents

By D. An, J. Withers

A nano-scale investigation has been carried out by applying an AFM (atomic force microscope) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it contacts the solutions of the collectors, suggesting that all these collectors can effectively adsorb on bastnaesite. Increasing temperature can help increase the adsorption of oleic acid on bastnaesite. FTIR (Fourier transform infrared) results also show that all these collectors adsorb strongly on bastnaesite with a strong absorbance spectra being detected, which confirms with the results obtained with AFM imaging analysis. In general, hydroxamic acid collector (HA and SHA) adsorbs on bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite. INTRODUCTION Rare earth metals, which are very important to modern industry, are generally extracted from numerous rare earth minerals. In practice, however, the actual extraction of rare earth is mainly from bastnaesite, monazite and xenotime. The Mountain Pass mine is one of the largest rare earth mine in the world, at which the main rare earth mineral is bastnaesite. In the past years, froth flotation has been applied to the beneficiation of Mountain Pass ore. In practice, the rare earth ore is usually crushed, milled and further separated from calcite, barite and other gangue minerals by froth flotation, in which the rare earth oxide-bearing minerals stick to aerated bubbles in the pulp and float to the surface, leaving the gangue at the bottom of the flotation cell and disposed of as tailings.(Bulatovic, 2010) In spite of the fact that froth flotation has been applied to treat the bastnaesite ore at the Mountain Pass mine, the rare earth oxide (REO) recovery is still low,(Anderson, 2015) especially compared to the one obtained with sulfide flotation. For example, the typical recovery obtained at the Mountain Pass mine was only about 70%. This may be due to the low selectivity of the collector (oleic acid). In addition, to enhance the flotation selectivity, the pulp in the mine circuit has to be heated up to 70 to 90°C and it involves a lot of energy consumption. Last but not the least, a lot of depressants have to be added to improve the selectivity of flotation process. Therefore, it is critical to re-examine the existing flotation process at the Mountain Pass mine and seek any chance of improvement. (Anderson, 2015)

Jan 1, 2019

By Thomas E. Shufflebarger

Glass is one of man's most versatile creations. ---The earliest glaze known---is about 12,000 B.C. ---The oldest pure glass is a moulded amulet of about 7,000 B.C.---. Indicative of a knowledge of properly-proportioned, quality raw-material, means were found for producing the first relatively clear, transparent glass at about the beginning of the Christian era. The fundamentals of almost all the modern, technical processes of manufacture were established during the 3rd Century. (1) Glassmaking, practiced in Colonial America, was moved toward the Ohio Valley in response to increasing demands for fuel. This move, beginning in the 1860's resulted in the use of the glass sands contained in the Oriskany (and St. Peter) sandstone. (2) Glass sand,(3) virtually pure, fine-to-medium-grained quartz sand(4) is the principal raw material used in the manufacture of glass; it constitutes proportions which range to a maximum of about 72% and seldom is glass made without it. However, acceptable glass sands are, invariably, those which most nearly fit the glass-producer's economic needs and any method used to evaluate a raw material's potential must finally prove equatable with such needs. As used in the United States, source-rocks of glass sand include sandstone, unconsolidated silica sands, quartzites and vein-quartz. Admixtures of silica sand and other (principally clay and feldspar), readily separable components have been proven viable. However, the silica sand, refined by nature to a high degree of purity, is the desirable product of exploration. If the term, standard, is justified by long-continued use, the Oriskany - and St. Peter sandstones are, together, the nonesuch of the glass sand industry they provide the principal tonnage of melting sand. According to Grimsley,(5) Ottawa, Illinois, glass-sand is considered the standard glass-sand of the West and the analyses of Berkeley Springs sand (Oriskany) compare most favorably with this sand.

Jan 1, 1974

By F. Calizaya

A booster fan is an underground ventilation device installed in the main airstream to handle the total quantity of air circulated to one or more working districts. It is installed in a permanent stopping and equipped with airlock doors, a monitoring system and interlocking devices between the main fan and the booster fan. When adequately installed, a booster fan can be used to reduce the main fan pressure, reduce leakage and decrease the power consumption. However, an inadequate installation can increase the likelihood of mine fies and recirculation of air contaminants. This study identifies hazards associated with the operation and maintenance of booster fans. It analyzes the accompanying risks and recommends control measures to reduce those risks to acceptable levels. The ventilation network of an existing coal mine was updated to include a booster fan. The hazards associated with the operation of this fan were identified, the risks analyzed and the esponse to each failure mode established.

Mar 1, 2014

By C. J. Pritchard

The Office of Mine Safety and Health Research (OMSHR) investigated ways to increase mine airflow to underground metal/nonmetal (M/NM) mine working areas to improve miners? health and safety. One of those areas is controlled recirculation. Because the quantity of mine air often cannot be increased, reusing part of the ventilating air can be an effective alternative, if implemented properly, until the capacity of the present system is improved. The additional airflow can be used to provide effective dilution of contaminants and higher flow velocities in the underground mine environment. Most applications of controlled recirculation involve taking a portion of the return air and passing it back into the intake to increase the air volume delivered to the desired work areas. OMSHR investigated a Nevada gold mine where shaft rehabilitation was in progress and one of the two main fans was shut down to allow reduced air velocity for safe shaft work. Underground booster fan operating pressures were kept constant to maintain airflow to work areas, inducing controlled recirculation in one work zone. Investigation into system behavior and the effects of recirculation on the working area during times of reduced primary ventilation system airflow would provide additional information on implementation of controlled recirculation into the system and how these events affect M/NM ventilation systems. The National Institute for Occupational Safety and Health monitored the ventilation district when both main fans were operating and another scenario with one of the units turned off for maintenance. Airflow and contaminants were measured to determine the exposure effects of induced recirculation on miner health. Surveys showed that 19% controlled recirculation created no change in the overall district airflow distribution and a small reduction in district fresh air intake. Total dust levels increased only modestly and respirable dust levels were also low. Diesel particulate matter (DPM) levels showed a high increase in district intake mass flow, but minor increases in exposure levels related to the recirculation percentage. Utilization of DPM mass flow rates allows input into ventilation modeling programs to better understand and plan for ventilation changes and district recirculation effects on miners? health.

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be re-handled. Prior studies have shown that by only changing blast hole timing with the same blast design, fragmentation and throw alters. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum inter-hole delay for fragmentation has been found by studying timings from 0ms to 45ms. Instantaneous timing between holes increased the throw by over 100 ft, but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw. This paper investigates this optimized inter-hole timing while altering top and bottom column primer time to potentially improve throw while maintaining optimum fragmentation. Timings studied are top initiation, bottom initiation, and top and bottom simultaneously. INTRODUCTION Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading, and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.” Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is re-handled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators has allowed for precise delay timings to be used between rows, holes, and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation. This study consisted of 3 full scale bench blasts at a granite quarry in Talbotton, GA. Each blast was characterized by the timing delay between the top and bottom primer in the blast column of each hole; one simultaneous blast with a 0 ms delay, a bottom-initiated blast with a 1 ms delay, and a top-initiated blast with a 1 ms delay. Fragmentation analysis of the resultant muckpiles was performed using a combination of the PortaMetrics handheld point-and-shoot rugged tablet from Motion Metrics and the software WipFrag from WipWare. Throw was measured by placing strategic distance markers on the floor of the bench and then taking overhead photographs of the muckpiles after each blast. High-speed video footage was captured of each blast using an MREL Blaster’s Ranger II camera."

Jan 1, 2017

By David Brown, Adrian St. John, John Comins, Mike King

"INTRODUCTION The Crossrail project provides an East-West link across London enabling an additional 200 million journeys each year linking up major business centres and existing transportation interchanges, while reducing congestion at street level and within the current underground system. The project has built major structures in Sprayed Concrete Linings (SCL), including 5 new stations, 6 crossover caverns and numerous passages, adits and ventilation tunnels. Construction has taken approximately 4 years, and has involved the spraying of over 200,000m3 of concrete. At the start of the project there was a lack of available records from previous projects concerning concrete falls, which hindered risk assessments and the ability to make meaningful comparisons around spraying or material performance. This paper redresses this lack of data by providing information on falls experienced on this project and makes recommendations to assist future projects. Construction Methods Table 1 below summarises the main contracts with elements of permanent SCL. The listed primary lining lengths include pilot tunnels, side drift tunnels and enlargements as separate tunnels.A range of construction sequences were used in order to deal with the design requirements, geometry, and the ground and ground water conditions. The following briefly summarises the build up by layers, with typical design dimensions provided for a platform sized tunnel (approximately 9m internal diameter), excluding tolerance allowances. Some linings were sprayed in more than one layer to allow for inclusion of reinforcement layers or to avoid a too aggressive build-up of thickness: •,Initial shotcrete, or sealing, layer (ISL) of 75mm followed by a Primary Lining (PL) of 300mm. •,Regulating layer of 40mm followed by a Waterproof membrane (Sprayed membrane, 3-6mm). •,Secondary lining (SL) of 250mm with a separate sprayed fire protection layer (FPL) of 50mm."

Jan 1, 2016

By G. B. J. Leon, M. Karmis, C. Newman

"The prediction of surface deformations due to underground mining operations has been a long recognized practice with case studies documented as far back as 1556 in Georgius Agricola's De Re Metallica (Latin for On the Nature of Minerals). There is currently increased public awareness and regulatory scrutiny on the potential impacts of underground longwall and second mining operations, but this time the focus is placed on environmental impacts to overlaying bodies of water such as streams, rivers, wetlands, lakes, etc. (Karmis and Agioutantis, 2015). Community residents and environmental groups, as well as federal and state regulatory agencies, have often cited adverse stream impacts and demanded stronger measures and scrutiny in issuing mining and reclamation permits (Booth, 2006). Mining companies are required to focus on the protection of sensitive bodies of water through the monitoring of stream flow and water quality, management and rehabilitation techniques, as well as the adoption of ""no mining zones,"" which potentially sterilize large portions of minable coal reserves. This paper examines the use of an empirical modeling approach for the protection of surface streams based on evaluation of ground strain magnitudes. Utilizing enhanced features of the Surface Deformation Prediction Software (SDPS), ground movements can be predicted accurately in the vicinity of surface bodies of water. The modeling of ground movements can aid in establishing optimum extraction sequences, while the magnitudes of anticipated subsidence can be used in the evaluation of mitigation plans when undermining surface bodies of water. INTRODUCTION When utilizing high recovery underground mining methods, such as longwall or room-and-pillar mining, the movement and deformation of the overburden propagates toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope, and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidence initiated changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, subsidence induced strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed, ""ruptures,"" upward blocking stream flow or having the stream diverted into the facture zone at the base (Iannacchione, et. al., 2010)"

Jan 1, 2016

By C. R. Stephan

There are a large number of facilities throughout the world which handle coal, such as preparation plants. Many other facilities use coal as a fuel, such as cement and lime factories. Although coal can be handled safely and can be an efficient fuel, there are explosion hazards which are accentuated as the particle size is reduced. Particle sizes of coal which can fuel a propagating explosion occur within thermal dryers, cyclones, baghouses, pulverized-fuel systems, grinding mills, and other process or conveyance equipment. This paper discusses how explosions can occur within these facilities.

Jan 1, 1998

By F. Alsobrook

Coleman Quartz Inc. has a long history as the sole U.S. producer of lascas for the cultured quartz growing industry based on its unique deposits in Arkansas. Since 1989 the company has also been producing metallurgical grade silica for the ferrosilicon industry from a deposit of unusually pure Arkansas novaculite. This paper chronicles Coleman's trans-formation of an abandoned railroad ballast quarry into a generator of $1.5 million in annual sales to a nontraditional novaculite market. Potential additional applications for this high quality silica rock will also be mentioned.

Jan 1, 1992

By T. M. Yegulalp

A new explanation of the scale dependency of the strength properties of rock is presented based on the theory of extremes. A review of past work on specimen size strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect on the statistical properties of the strength distribution. It is shown that the weakest link theory is directly related to extremal statistics and properties of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1992

By Robinson Leon-Diaz, Alberto Jaen-Toribio, Raymond Blanchard, Mike Deevy, Miguel Fuentes-Llanos

"Tunnels designed to NFPA 502 are required to withstand the RWS time-temperature curve, more specifically prevent progressive spalling and loss of strength of steel reinforcement. Fire boards or spray-on layers can be effective, however, these solutions have capital and whole-life cost implications. The use of “fire resistant” concrete based on a suitable aggregate with polypropylene fibers has also increased in recent years. This article presents a new methodology for thermal and structural analysis of segmentally lined tunnels, which permits the analysis of project specific fire curves and an assessment of different fire protection strategies. The effectiveness of fire boards is assessed along with whether “fire resistant” concrete alone is a viable means of achieving the required protection. Finally, since NFPA 502 recommends water-based fixed fire-fighting systems for Category C and D tunnels, we discuss the question of how a fixed fire-fighting system should be addressed within the structural design. INTRODUCTION Protecting road tunnels from structural damage and collapse is a key requirement for both life safety and business continuity. Where road tunnels are part of key highway corridors, protecting business continuity is a high priority for owners, operators and the Authority Having Jurisdiction. For existing tunnels, compliance with NFPA 502 may require upgrades with either passive fire protection and/or water-based fixed firefighting systems. For new tunnels, compliance with NFPA 502 requires a combination of good practice in design and fire testing. A water-based fixed firefighting system is a Conditionally Mandatory Requirement1 for Class C and D tunnels, i.e. all tunnels greater than 300m and 1000m long respectively. The basis for fire safety design of new tunnels and assessment of existing tunnels is the worst-case fire scenario. A number of factors, including but not limited to the following, influence this design fire scenario:"

Jan 1, 2016

By William J. Douglas

Critical path modeling (CPM) has been used widely as a tool to manage large-scale projects having many activities which are conducted in series or parallel. The construction industry is a regular user of critical path modeling as a planning tool. In this context, the method is used to provide an orderly schedule for all activities to forecast delays, slippages, and problem areas and to identify critical activities where resources should be directed. It also identifies others which have slack time, and provides information on the degrees of freedom and flexibility available in completing the project. The purpose of applying critical path modeling to an underground mining system is not primarily for scheduling, but as an analysis tool. In observing underground mining systems, it Is clear that repeated sequences of activities must take place for mining to proceed efficiently. Some of these activities must be sequential, while others be carried out in parallel. The fundamental difference between critical path modeling applied to mining versus a large-scale construction project are: (1) The activities in a mining system are cyclic in nature. (2) The location of the activity varies, and the entire process is not thought of as co-located, as is the case in a construction project. Another important aspect of the network development for mining systems is the degree of detail that is desired. One can be concerned with very macroscopic networks which represent, for example, an entire mine life cycle. Networks representing this problem would be more closely analogous to those of a large construction project. On the other hand, one might be interested in evaluating alternative ways of developing a property or of mining in a given section. More detailed networks representing the section activities are necessary to evaluate system parameters and their impact on long-term production.

Jan 1, 1978

By B. Das

Most coals are susceptible to spontaneous heating which in turn creates problem to mining, storage and transportation of coal. It is impossible in actual practice o eliminate spontaneous heating but spontaneous combustion can effecively be controlled through a clear understanding of its mechanism and the factors affecting it. There are altogether six stages in the process of spontaneous combustion. This includes the water adsorption stage and six oxidation stages: chemi-sorption (upto 70°C), decomposition of peroxygens (70°C-150°C), oxy-coal formation (150°C-230°C), combustion initiation (230°C) and active combustion (> 230°C). Heat is produced in all these stages. On the other hand heat is also dissipated so that some equilibrium temperature is reached. If this temperature exceeds a certain critical value (generally about 70°C), coal oxidation may advance to spontaneous combustion. The major factors influencing spontaneous combustion of coal are: coal rank, maceral composition,, water, mineral matter, joints and fissures, seam depth and thickness, mine Layout, method of ventilation, etc. Susceptibility is high for low rank coals and generally decreases with increase in rank. Of the macerals, the exinites are generally most susceptible, the inertinites least and the vitrinites somewhere in between. Water plays a major role on the spontaneous heating of coal, assisting in someways and inhibiting in other. Unrecovered coal in the gob (generally in thick seams) is a major source of fire hazards and this is specially important in shallow mine. Proper design of mine ventilation system can substantially reduce the risk of mine fire. Panel layout and load transfer can affect the development of induced cracks which in turn influence spontaneous heating. Finally, the difference between the spontaneous heating of coal in a seam and that in storage or transportation is mainly due to the change in moistured content, air circulation through the coal and coal fragmentation. These aspects have been analyzed in this paper with a view o reducing the risk of spontaneous combustion.

Jan 1, 1986

By R. Kramer, A. Habibi

"Diesel Particulate Matter (DPM) measurements were taken at Tronox’s Westvaco Trona mine in Wyoming. Both shift-average and real-time monitoring using Elf pumps and Airtec analyzers, were used. The mine’s underground transportation fleet consists of more than 250 diesel-powered vehicles. A vehicle monitoring log tracked fleet usage during the test; logged data consisted of vehicle type, direction of travel, and time. The log was used in analysis to determine the DPM spread rate, of normally operating equipment, in the different entries with respect to vehicle location. Airflow velocity measurements at the stations were taken during the survey. The survey results also identified vehicles with higher emission rates. An ECOM gas and a MAHA DPM analyzer, both located in the mine’s underground emission shop, were used to obtain various vehicle emission rates. The correlation of the workshop and field measurements was investigated with regard to the machine activity, fuel usage and atmospheric conditions. The results were used to identify and execute a ventilation project to reroute 45% of diesel shop air back to intake entries, by interlocking an automated door and a regulator. The result is reduced DPM downstream. INTRODUCTION DPM has been classified as a potential occupational carcinogen by the National Institute for Occupational Safety and Health (NIOSH).The Mine Safety and Health Administration (MSHA) rule governing DPM exposures in metal and nonmetal mines cites total carbon (TC), a summation of elemental carbon (EC) and organic carbon (OC) obtained by NIOSH Method 5040, as a surrogate for determining DPM exposures (Noll, 2006). MSHA personnel use the 1973 sampling criteria outlined by the American Conference of Government Industrial Hygienists (ACGIH) for collecting compliance-based respirable and inhalation samples in metal/nonmetal mines. Instrumentation developments are allowing improved real time monitoring of ventilation parameters. DPM is within the aerodynamic particle size range of the samplers used for respirable and inhalable dust measurements. If a sampler used by MSHA to collect inhalable or respirable dust samples in underground metal/nonmetal mines was used to collect DPM, both the DPM and mine ore dust would accumulate on the sample filter (Noll, 2006). To comply with the requirement and lower the DPM exposure, mines are implementing a variety of control technologies such as emission based maintenance programs where adjustments or repairs are performed on the vehicles (McGinn, 2000)."

Jan 1, 2016

By Jr. Pitts

Elevation of surface charge density on colloidal particles in the presence of a high potential electrostatic field is demonstrated as a viable technique for preventing the accumulation of solids in solvent extraction circuits. The effect of the technique is manifest by relative turbidity measurements between pregnant leach solution and raffinate, by changes in the character of the sludge accumulations, by alteration of the zeta potential of particulates, and by a general reduction in the mass of solids.

Jan 1, 1992

By R. A. Jankowski

The U.S. Bureau of Mines has conducted a study to identify the sources of respirable dust and appropriate dust controls applicable to today's high tonnage longwall faces. The primary source of respirable dust identified is the cutting action of the shearer; however, the pct contribution of dust from coal transport through the stageloader/crusher was significant. This was primarily due to the high rate of mining, requiring rapid and constant coal transport. Techniques implemented for the control of shearer-generated dust included high drum water flow rates, deep cutting, shearer-clearer-type external water spray systems, and radio-remote control. The high water flow rates, and an enclosed stageloader with scrubber, were used to control dust during coal transport. No novel or effective control technology exists to control dust during support advance. Administrative controls for dust avoidance, and manual and batch-activated electro-hydraulic control systems were used to keep support movers out of the dust generated during support advance.

Jan 1, 1990

By Anita Wu

"GENERAL BACKGROUND/CONTEXT The £300 million Bond Street Station Upgrade project will provide essential congestion relief and step-free access to an important interchange and destination station in the heart of the London Underground network. In 2010 London Underground (LU) let a design & build contract to Costain Laing O’Rourke (CoLOR), with the works to be completed in early 2017. CoLOR’s lead designer is Halcrow-Atkins JV (HAT). The station upgrade works comprise the following principal elements: •,A new satellite ticket hall on the North side of Oxford Street •,Two additional escalators and stairs providing congestion relief to the Jubilee line platforms •,Four lift shafts to provide step-free access between the different levels of the station •,Additional stairs to Central line platform level •,Tunnelled connection to the Crossrail station immediately to the south •,Connecting passageways, including ten connections to existing station tunnels. To achieve this, an existing property at 354-358 Oxford Street has been purchased and demolished, and the basement deepened to make provision for the new ticket hall. From this basement two circular shafts have been sunk, providing construction access for the tunnelled passages and lift and escalator shafts. The tunneling is principally in the London Clay stratum, which is widely recognized as a favorable tunneling medium, although the deepest parts of the works extend into the Lambeth Group strata which consist principally of stiff clays at this level but also contain water-bearing sands. The majority of tunneling has been carried out using mechanical excavation and sprayed concrete linings but other techniques have been used in areas where SCL is not practicable.A key challenge for design and construction of the works has been spatial constraint, in particular due to: •,The existing underground station layout •,The Limits of Deviation for the works •,The small construction site at 354-358 Oxford Street •,Overlaying Third Party assets including Listed buildings, sewers and water mains."

Jan 1, 2016

By Weijie Wei, Jinwang Zhang, Jiachen Wang, Yang Li

"Longwall top-coal caving (LTCC) mining technique is one of the important methods for underground thick seam extraction in China. The coal seam in LTCC panel is divided into two parts: bottom-coal and top-coal. The bottom-coal is mined by conventional longwall method while the top-coal is mined by caving method. The top-coal caving process in LTCC and block caving process in metal mine are both gravity flow of loose ore/coal blocks. However, the presence of caving shield in LTCC makes the characteristics of drawing body shape in the two caving processes differ a lot. This paper discusses the influence of caving shields on the characteristics of drawing body shapes in light of recent studies of the top-coal drawing process. The theoretical model for describing the drawing body shape in LTCC is proposed both along the seam strike and seam inclination. Then, the experimental data are used to validate the correctness of the theoretical model. Furthermore, two examples of how the theoretical findings assist LTCC mining are given and discussed.INTRODUCTIONLongwall top-coal caving (LTCC) mining technique and large-cutting-height mining technique have been widely used for extracting thick coal seams in China. About 0.6–0.7 billion metric tons of coal come from longwall top-coal caving panels every year. The maximum annual production is 15 million metric tons per panel _The mining method employed in such panel is a combination of top-coal caving mining technique and large-cutting-height mining technique, which is suitable for seam height between 12–20 m, as shown in Figure 1. Apart from China, LTCC has also been employed in some coal mines in Australia and Vietnam (Le et al., 2017).The coal seam in a LTCC panel is divided into two parts: bottom coal and top coal. The bottom-coal is mined by the conventional longwall method, while the top coal is mined by the caving method. The top-coal caving process in LTCC and block caving process in metal mines are both gravity flows of loose coal/ore blocks, as shown in Figure 2. However, the presence of caving shields in LTCC causes the characteristics of the drawing body shapes in the two caving processes to differ significantly.There are two main differences between the blocking method and the top-coal caving method:"

Jan 1, 2019

The Henderson Mine is a large underground panel cave molybdenum mine located near Empire, Colorado. Secondary blasting requirements have varied from one shot per 27 tonnes (30 tons) to one shot per 900 tonnes (1,000 tons) of ore. Geology, structure, cave abutment loads, and location of the ore in the column all affect the amount of oversize boulders (greater than three-fourths cubic meter or one cubic yard) that require secondary breakage. The primary method of breakage utilizes cone charges (plastic funnels filled with an emulsion) placed on accessible oversize rocks. Hangups in the brow area of the drawpoint are drilled with a self contained diesel hydraulic drill and loaded with gelatin dynamite. High hang-ups located beyond the reach of the secondary drill are "bombed" in with strategically placed emulsion bundles or ANFO bags loaded in place though a sectioned aluminum pipe.

Jan 1, 1994

By Ronald D. Hill

The occurrence of acid mine Drainage (AMD) with coal mining has been well documented. (1) Less documentation is available of its association with other types of mining, e.g., copper, gold, zinc, and sulfur. Yet there are many locations in the western states where acid mine drainage is as great a pollution problem as in Appalachia and in some cases, because of the high copper, zinc, and arsenic concentrations, they present an even more difficult problem. Until a few years ago, it was generally believed that the neutralization of acid mine drainage was uneconomical thus, AMD was allowed to discharge freely into our streams. However, the demand for good water finally dictated that the mining industry be included under pollution laws. In 1964 the Commonwealth of Pennsylvania passed a law requiring that all active mine discharges meet a discharge standard of pH 6-9, iron less than 7 mg/1, and the water must have a net alkalinity. Several other states now require active mines to treat AMD. In all but a few cases, lime neutralization, often in conjunction with aeration, has been the treatment method used. The high cost of lime as compared to limestone and the poor quality sludge, (slow settling, large volumes, and low solids content) has stimulated work in the utilization of limestone. This paper reports on the current state-of-the-art of limestone treatment of AMD.

Jan 1, 1970