Search Documents

By R. L. Amelunxen

P. T. Freeport Indonesia (PI) in conjunction with Crescent Technology Inc. has developed a method to predict the metallurgical performance of ores blends based on the behavior of their component ores. The question addressed in this paper is whether ores treated individually could be extrapolated to predict the behavior of a blend of ores. The work further investigates the use of modal analysis to establish individual mineral flotation kinetics in each of the ore zones. This information would lead to the prediction of grade-recovery curves of ores made up of those minerals. Nine samples of ore, representing various zones of FI's Grasberg ore deposit were tested metallurgically and examined microscopically. The same testwork was performed on blends depicting the 1994 mill quarterly feed. Flotation kinetics of the individual ores were then "mathematically" blended and compared to the results obtained from the quarterlies. The calculated kinetics of the actual blends of ore received by the mill were fed to the simulation program and compared to the actual mill performance.

Jan 1, 1995

By O. M. Johnson

Barite and bentonite are the two principal components of drilling fluid systems used in the petroleum industry for oil and gas well drilling with rotary-type rigs. Approximately 87 percent of the world's annual production of barite is used in drilling applications. Of the worldwide production of bentonite, an estimated 30 percent is used. The drilling fluid, or drilling mud, to which barite and bentonite are added, performs five distinct functions: Lubrication-The liquid phase of the drilling mud lubricates the drill bit, preventing premature failure of the cutting edges and bearings. it also helps to soften the formation being drilled. Cuttings Removal-A mud system must be able to carry rock cuttings broken loose by the bit up to the surface where they can be removed by mechanical or chemical methods. The fluid's ability to perform this function depends upon maintaining a proper balance between the rate of circulation of the fluid and the colloidal properties required to entrain the cuttings in the mud to prevent their settling to the bottom of the hole. Hole Stability-The pressure exerted by the mud against the wall of the bore hole prevents the collapse of the uncased portions of the hole. Downhole Information-The fluid characteristics of the mud should be such that good cuttings samples, cores and electric logs may be obtained to help evaluate a well's productive zones and potential. Control Oil, Gas and Water Flows-It is essential that a drilling fluid offset any pressure from naturally occurring formation fluids in order to prevent a potentially wasteful and dangerous blowout.

Jan 1, 1980

"Metallurgical process development in greenfield projects must define the comminution flowsheet and establish the equipment sizes that are required to deliver the project design criteria. These are critical steps that heavily influence the financial performance of the project, requiring a detailed understanding of the ore properties of the project resources and the best practice methods to size comminution machines. This paper reviews current practices for determining the ore characteristics relevant to comminution circuit design. Particular attention is given to the design of sampling and testing programs, and the methods commonly applied to size crushers and mills for conventional size reduction applications in mineral processing. IntroductionMetallurgical process development in greenfield projects requires the selection of a comminution flow sheet and must establish the equipment sizes required to deliver the project design criteria. This necessitates a detailed understanding of the ore properties that define the project resource. For brownfield projects the same objectives may apply for plant expansions, or the project objective may be simply to define the capacity and operating cost of an existing facility for a new ore source. The process development phase in either instance will typically comprise the following key activities:• Geometallurgical classification and sampling of the ore deposit or deposits.• Determination of comminution energy requirements.• Benchmarking similar projects.• Identification of flow sheet options.• Equipment selection and sizing.This paper is concerned specifically with process development testing and will as such focus on the first two activities on the list: sampling and testing of the deposit. The discussion will focus on testwork programs to support the design of comminution circuits commonly in use in mineral processing today, specifically crusher, tumbling mill and stirred mill technologies.It is important that any testwork program is designed giving consideration to the types of flow sheets that are viable for the project, and the data that will need to be generated to support the final equipment sizing. Designing a testwork program to only provide information about one particular type of flow sheet will not allow sufficient information to be generated for a rigorous trade-off analysis of options, and may therefore preclude financial optimization of the project. Testing programs should be designed to collect sufficient data to ensure that any backtracking at a later stage to fill in missing information is minimal."

Jan 1, 2016

By D. W. Struhsacker

Mineral exploration has evolved into a sophisticated science which uses powerful scientific tools to make mineral discoveries. In addition to their usefulness in performing mineral exploration, these scientific tools can assist the exploration geologist in assessing environmental conditions at exploration sites. During exploration, environmental data acquisition should focus on data collection efforts which can be easily integrated into exploration activities, and should provide information needed for pre-feasibility and preliminary engineering design studies. Environmental studies performed during exploration should also include an environmental liabilities audit and a fatal flaw analysis to assess whether there are any unresolvable environmental or regulatory issues affecting the project. Performing extensive environmental baseline studies during exploration and project evaluation is neither necessary nor recommended. This paper describes opportunities to integrate environmental data collection with mineral exploration activities. This paper also examines how political and communication issues can affect the outcome of permitting efforts, and recommends a strategy to improve the industry's ability to respond to political challenges and to communicate with the public. This strategy integrates technical and political issues, and implements programs to convince the public of the mining industry's technological achievements and its commitment to resource stewardship and environmental protection.

Jan 1, 1994

By G. Blackwell

In the 1980's the Canadian surface mining industry was confronted by declining competitiveness in the face of low cost foreign producers and alternative materials. Low metal prices undermined profits for many mining companies. Restructuring, rationalization, capacity reduction, technology transfer, as well as favourable currency rates and higher commodity prices, helped revitalize the industry by the close of the decade. Now in the 1990's, however, the need to improve competitiveness for profitability has re-emerged in greater intensity. In the current climate it is considered that there are three strategies available to industry to ensure profitability: continued rationalization and restructuring; optimization of operating practice; and technology development and transfer.

Jan 1, 1993

By H. Sevim

Three transportation systems in surface coal mines: 1-Truck Haulage, 2-Belt Conveying, and 3-Coarse-Coal Slurry Transportation are compared from the operations and cost point of Views. Computerized design and cost models were developed and cost data banks were compiled for each system. These models can be used to evaluate transportation systems and layouts that are practiced in most of the U.S. surface coal mines. A typical midwestern area strip mine was considered for illustration purposes. Sensitivity analysis on critical parameters such as production rate, transportation, distance, etc. was conducted and the outcomes are presented.

Jan 1, 1990

By T. Krumins, L. Zunti, R. Frischmuth

"Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals and other process piping. In the autoclave vent application, titanium ignition risk is controlled by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature operating conditions and therefore oxygen concentration and the associated titanium ignition risk is dependent on standard operating procedures, process control interlocks and permissive conditions. It is not uncommon for these standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for a titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions. INTRODUCTION High temperature pressure oxidation (>190°C) is a well recognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulphide ores and concentrates before conventional leaching with cyanide. Titanium and titanium alloys are highly corrosion resistant in pressure oxidation process conditions and are therefore commonly selected as materials of construction for many components including: autoclave internals, agitators, process piping, and components in autoclave vent systems. Operations that anticipate or have experienced aggressive corrosion in the vent system often have little choice in material selection other than the use of titanium (Krag & Henson, 1992). Titanium is not suitable for use with elevated oxygen concentrations and is considered a restricted material because of its high pyrophoricity and combustion propagation properties (Beeson, Smith, Stewart, 2007). Several serious incidents have occurred in which titanium materials have ignited in autoclave applications (Zawierucha, McIllroy, Million, 1995). In autoclave vent applications, titanium ignition risk is reduced by preventing elevated oxygen concentrations, maintaining low gas velocities, and minimizing the potential for gas impingement on surfaces. Oxygen concentration in the autoclave vapour phase and vent system is dependent on the autoclave operating pressure and temperature conditions and therefore titanium ignition prevention controls typically include process interlocks and operating procedures based on the selected nominal design operating conditions. However, it is not uncommon for these controls to be deficient or for operations to deviate from the nominal operating conditions over time, increasing the risk of titanium ignition. The introduction of an online calculation of autoclave overpressure and a maximum target autoclave pressure as well as associated process control interlocks and permissive conditions can alert the autoclave control room operator and prevent an elevated oxygen concentration from developing, and therefore reduce titanium ignition risk in autoclave vent systems."

Jan 1, 2016

By George E. Aikens

Prolonged subzero climatic conditions impose some unique engineering problems for the developer and operator of open-pit mines in the Far North. The remoteness of the job site and the extremely cold, long, dark winters severely tax both man and machine in the quest for the Arctic's rich mineral wealth. Undoubtedly the singular most troublesome problem for the engineer is Permafrost which underlies about 201o of the land area of the world and about 85% of the state of Alaska. Permafrost has its impact on building construction and mine excavation, while posing a more pervasive threat to the-delicate ecologic balance within the Arctic wilderness. Yet the difficulties associated with mining up North may not be as overwhelming as has been previously supposed. For example, the lowest temperature recorded at Point Barrow is -560F, whereas Montana has recorded -69.7° F.. There are no specially designed machines for mining and construction in the Arctic, and efficient equipment utilization is maintained through proper operation and servicing techniques. However, neither equipment or people can be assumed to function normally at -40°F. Special techniques in drilling, blasting, and ripping are being used to yield economically competitive ores. Overall, a fundamental understanding of the nature of Permafrost will allow the engineer to deal expeditiously with an Arctic mining venture and at the same time to deal fairly with Arctic environment.

Jan 1, 1972

Integrated mining information and process control systems can reduce information delays, enhance decision making and improve the responsiveness of mining operations to, for example, variations in market conditions, mineral grades and ground conditions. This paper examines developments in the areas of: monitoring, data analysis and diagnosis,' communications systems; integrated mining support system;, and process and machine control. It concludes that the development of a comprehensive information technology plan is fundamental to the phased implementation of these technologies. In addition, hardware and software standards and concurrent digital design and simulation practices in selected manufacturing industries are examined and concluded to have relevance to the mining industry. Integrated information and process control systems will lead to emergence of the "digital mine". Such advances in mining information infrastructure as well as mining equipment will enable mining operations to shift from mass production methods to leaner production techniques. "Lean mining" aims to enhance and accelerate cash flow over the life of a mine by focusing on reduction of' throughput times; stockpiles for volume and quality control; and wastage and rework.

Jan 1, 1995

By E. Berrezueta

Automatic digital phase imaging should yield unbiased and representative characterizations of gold ores. However, this is not a simple tusk due to low gold grade, fine grain size, possible complex mineralogy, nugget effect, etc. Using the same sections of a gold-rich ore, a critical test was performed using an optical microscope (OM) and an electron microscope (EM). In general, the two methods are consistent and useful for ore processing. There are some minor differences, such as the detection of very fine gold grains is enhanced by EM. Key words: Digital imaging, Gold ores, Mineralogy, Electron microscopy, Optical microscopy

Jan 1, 2003

Conditional simulation provides a model of the ore body that represents variability in the data. This can be used to determine the impact of various grade control and mining strategies. A number of transfer functions are discussed that assist in optimizing grade control sampling. The cost effectiveness of various drilling and trenching techniques are discussed. Modelling of the expected performance of a mill head grade sampler is investigated. Conclusions are drawn about the likely impact of various sampling techniques on the economic performance of an operation and about applying sampling theory to grade control sampling.

Jan 1, 1999

By M. Rieber

The potential for the wide-spread commercialization of superconductivity, the disappearance of all resistance to a direct current (D.C.) electric flow, began in 1986-87 with the development by Bednorz and Muller at IBM's Zurich Laboratory of an yttrium -barium -copper oxide conductor which attained zero resistance at 90t:. Although the status of superconductivity is still pre-bench scale, it is useful to forecast its probable effects on the copper industry. I t should not be forgotten that at their inception, the impacts of transistors, semi-conductors, thin films and fiber optics on the electric/electronics sector of this industry, were largely underestimated. Superconductors are not metals, but a class of ceramics. They represent an efficiency increase of one or more orders of magnitude. If their development is to be a boon to the copper industry, rather than a reduction of metal demand through miniaturization or material substitution, vastly expanded copper containing electrical uses must be in prospect. In this paper the projected uses of high temperature superconductivity are examined, followed by the remaining problems to be overcome. Assuming success, a time horizon for maturation is estimated. The penalties for the non-recognition of new markets and material substitution are shown on the basis of past forecasts. Finally, the application of successful superconductivity to the copper industry over the forecast period is estimated.

Jan 1, 1990

By Ahmet Unal

Use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments will be reviewed, giving specifications of some past and currently available systems. The advantages and disadvantages of using various frequencies, system configurations, and specific components, including their construction standards and capability, will be discussed. The remaining challenges to more widespread use of RFID systems for personnel and vehicle tracking will be identified, and recommendations concerning operating environment capabilities will be detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency will be discussed.

Jan 1, 1997

By R. L. Grayson

In 1995, Congress abolished the Bureau of Mines in the Department of Interior but preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the merger of the former Bureau with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data informed" priority setting. This presentation will review current surveillance information concerning the level of injury and disease from mining work and will discuss how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 1998

By L. Donovan Clark

The term "powder factor" is almost universally accepted as the measure of the efficiency of a blasting program. It represents the economics of blasting since it designates quantity of explosive (thereby providing quality control in rock fragmentation) in terms of the associated volume broken. It is the wide use of this concept that explains the interest shown in an approach to rock blasting preferred by A. W. and Z. W. Daw* in a treatise on 3 blasting (1) substantiating its use in the form, Q = CVW3 for single shot hole, where Q = quantity of explosive lb Cv = blasting coefficient W3 = unit volume of rock It is obvious that the term Cv could also be called the apparent powder factor should the equation be written in the form, Cv = Q/W3 (lb per cubic unit). However, while the approach was ingenious** and the practical applications straightforward, their original, rather limited experimental work, along with certain assumptions, was questioned.

Jan 1, 1970

By J. R. Patts, L. D. Patts, S. J. Janisko, T. Barone

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more efficient and effective use of rock dust. A prototype, flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed in line between the ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over a period of three days at set distances from the fan exhaust to assess the changes in float coal dust levels in the return due to the operation of the scrubber. Mass-based measurements were collected on a per-cut basis and were normalized per foot of advance by the continuous miner. Results show that average float coal dust levels measured under baseline conditions were reduced by over 91% when operating the scrubber. INTRODUCTION In 2012, underground mining in the United States produced over 342 million tons of coal [EIA 2013]. During the cutting, crushing, and transport of this coal, dust is generated and can be entrained in the air ventilating the mine. Title 30 Code of Federal Regulations Part 75.400-1 (30 CFR§ 75.400-1) defines float coal dust as particles of coal that can pass a No. 200 sieve. These coal particles can be carried by the ventilating air into return entries before settling onto mine surfaces [NIOSH 2006]. If this float coal dust becomes re-entrained into the airstream, it can propagate an explosion throughout mine workings [Harris et al. 2010]. Application of rock dust in underground coal mines is required by Federal regulation as a means of preventing the propagation of explosions by float coal dust. In order to meet Title 30 Code of Federal Regulations Part 75.403 (30 CFR § 75.403), 80% incombustible content must be maintained in the composition of dust deposited in mine entries [76 Fed. Reg. 35968 (2011)]. This fraction of incombustible content is increased if elevated levels of methane are present. In order to maintain the required incombustible content, frequent or constant application of rock dust is undertaken by mine operators. Title 30 Code of Federal Regulations Part 75.2 (30 CFR § 75.2) defines the properties of the rock dust that must be used by mine operators."

Jan 1, 2015

By C. Patrick

Longwall face-to-face transfers can cost over $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high cost makes extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. This paper reports operations research techniques used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate over 30% of the total U.S. longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation models of transfers under varying conditions were generated; and, the economics of general transfers and time-cost tradeoffs in the transfer procedure were investigated.

Jan 1, 1993

By S. P. Winkelmann

The expansion in gold production in the Carlin 'Trend over the last few years has been one of staggering proportion. To increase gold production while minimizing capital requirements and providing for the safe and efficient mining and processing of ores has required a tremendous effort by the Mine Engineering group at Newmont Gold. This paper discusses the organizational changes implemented to effectively deal with a full range of engineering problems and how the Newmont Gold Mine Engineering group dealt with these problems. Specially developed computer software and their applications will be explained. Improvements in the techniques used in converting geologic resources into reserves, and in scheduling the mining of multiple pits to feed multiple processing facilities, as well as ore control procedures are presented. Current mine engineering practices are discussed.

Jan 1, 1990

By A. Haghighat

The Missouri University of Science and Technology?s (Missouri S&T) Experimental Mine is a teaching and research facility which has been excavated in limestone by mining engineering students over almost 100 years. The mine is currently being extended to a second level. Available fans for ventilation are two surface fans of 24 kW and two underground booster fans of 12 kW. The design of a ventilation network in conjunction with multi surface fans and booster fans entails a complex procedure. Ventsim Visual software modeling has been used for network analysis to determine the optimum surface and booster fans locations, blade settings, and speeds. Both natural and mechanical induced ventilation pressures have been taken into account. Three working faces on each level have been designated as target points that minimum air quantities are required. The model has been calibrated against a pressure and quantity survey. Design of ductwork, door/stopping positions and different fans characteristics have been examined. The optimum flow rate at identified working faces, efficiency and minimum energy losses and annual network power cost determine the best scenario. The optimum design has been determined for the ventilation network for the next 100 years. The optimum flow rate across working faces is the key criterion selected.

Feb 23, 2014

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the U.S. National Institute for Occupational Safety and Health collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants revealed not having a systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. In this paper, we identify and describe three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication and specialized training, to increase awareness of imminent danger situations. IntroductionIn recent years, the metal and nonmetal mining sector, as categorized by the U.S. Mine Safety and Health Administration (MSHA), experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured, twice the number of fatalities in each of the previous two years (MSHA, 2015a). As a way to address this increase, MSHA issued its P15- IV-01 program policy letter, suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners” (MSHA, 2015b). The goal of these examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 9, 2018