Search Documents

By David S. Bolin, Bruce Kennedy, Leigh A. Readdy, Graham Mathieson

INTRODUCTION The estimation of ore reserves is a process that begins with the earliest exploration stages on a property and continues throughout any subsequent evaluation and exploitation of the deposit. During exploration and preliminary evaluation, the results of these reserve estimates constitute the basic data for prefeasibility studies and economic analysis. The decision to continue exploration and development or to abandon a prospect is often based upon these studies. During the active life of a mine, reserve computations are continuously revised to assist in development planning, cost and efficiency analyses, quality control, and improvement of extraction and processing methods. Accurate reserve estimates are also required when financing a project, purchasing or selling a property, and for accounting purposes such as depletion and tax calculation. It is important to remember that the reliability of ore reserve estimates varies progressively through time as more and more information becomes available. The lowest order of reliability of estimation of reserves exists at the time of discovery. The maximum level of certainty concerning the ore reserves within a deposit is reached when the deposit is completely mined out. Between these two extremes are variable levels of certainty as to the tonnage and grade of the resource. This is particularly true of that portion of the mineral resource that constitutes the "minable reserve," as this portion is dependent upon economic as well as geological and technological factors. In the following discussion, several of the factors affecting ore reserve computation and some of the commonly used methods of calculation are presented. The first part of the discussion is confined to classical methods of hand calculation utilizing level maps and sections. The second part of the discussion presents an overview of somewhat more sophisticated methods of geostatistics which have been developed within recent Years. Geostatistical methods frequently provide the best ore re- serve estimates for many deposits. However, a digital computer is required for such geostatistically derived estimates due to the number and complexity of the cornputations involved. For many properties the classical nongeostatistical methods are adequate, particularly in the early exploration stages. In fact, it is the author's contention that even at those properties where the geostatistical approach is employed for reserve estimation, the geological and engineering staffs should prepare an estimate by traditional means. This provides an internal audit for the reserves and at the same time requires a continuing close appraisal of geologic problems that influence the presently known geostatistically estimated reserves and production at the mine.

Jan 1, 1982

By J. Hanna

Four Ca-bentonitic clays from Alabama were evaluated for use in Diammonium Phosphate (DAP) or Urea Ammonium Nitrate (UAN) fertilizer suspensions. The viscosity and gel strength of suspensions prepared with different proportions of a Western bentonite clay and sodium exchanged Alabama clays, were measured as a function of clay content and dispersant concentration. The results obtained suggested that three of the Alabama Ca-bentonites would replace about 40% of the more expensive Western bentonite in UAN and DAP fertilizer suspensions. The performance of the Na-modified clays, prepared according to the TVA soda ash method, was as good or even better than those observed for the Mg-, Na/Mg-or K-modified clays. The TVA clay modification procedure appears to be reliable and cost effective.

Jan 1, 1989

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By F. A. Renninger

Limestone and dolomite are the most common rock types mined and quarried as industrial minerals in the United States. In 1993 over 720 million tons of limestone and dolomite valued at over 3.1 billion dollars were extracted and consumed throughout the nation. While the greatest volume of this vast production is used as aggregate for construction purposes, few people realize how critical limestone and dolomite are to our food chain and our national goals of clean air and water. Limestone, including dolomite, can truly be called nature's gift to the environment. Without a reliable, economical source of limestone the quality of our environment would be severely comprised and the standard of living of our citizens dramatically reduced.

Jan 1, 1995

By Manfred Hager

The ability of conveyor belts to transport large mass throughputs economically over previously unprepared ground has resulted in this system achieving great and extensive use. A significant component in this development is the conveyor belt itself. The development of high strength steel cord conveyor belts involves the optimising of splice design, the use of excellent rubber material especially in the splice, good craftsmanship during splice production and modern field vulcanisation equipment. The durability of a splice for belts of class St 3000 up to St 790 is expressed by the fatigue strength under dynamic stress. The results obtained with a test method and equipment developed by the University of Hannover indicate the present state of the art in this field. Belts of high nominal strength used on inclined long distance conveyors reach splice fatigue strengths of about 3000 N/mm. The design should only exploit approximately 50% of the fatigue strength determined in the tests as maximum operating stress. IMPORTANCE OF CONVEYOR BELT SYSTEMS The use of conveyor belt technology has expanded considerably over the last decades in the bulk goods transportation sector. Because of the favourable transport costs and the technology's adaptability to specific topographies, belt conveyors frequently represent the most economic solution. When flows of goods are large, as in German lignite mining operations, where masses of up to 40,000 t/h are given, it is the only technically feasible alternative. The use of belt conveyor systems allows the sensible distribution of the waste and the production of the coal (Hager, 1981). But this transportation alternative is also suitable when the masses involved are smaller. Whereas conveyor belts were only suitable for loose bulk goods up until a few years ago, today they are frequently also used for hard rock open cast mines, e.g. in the production of copper ore. Because of the favourable transport costs it is frequently still economic to use mobile crushers with a throughput of up to 10,000 t h 6 which breakdown the large blocks produced y explosives into transportable grain sizes. In many operations, trucks are only used to provide flexibility between the excavator and the crusher, i.e. over short routes, and the long, frequently steep, transport paths to the processing plant or to the spreader are undertaken by belt conveyors (Einenkel et al., 1992). The advantages of belt conveyors, i.e. to cope with large mass flows over inclines and down slopes of up to 1:4 have resulted in this system gaining very extensive use throughout the world. The conveyors can be installed over for the most part unprepared ground with suitable vertical radii, adapted to the locally available belt material. In the process individual conveyor belts with lengths of up to 15 km, and in the underground sector with lift heights of up to 1 km, have been built and operated. This great variety of application possibilities is complemented by a limited ability to pass through horizontal curves. This can be achieved with the help of design measures on the conveyor whilst bearing in mind the characteristics of the belt. STRESSING OF CONVEYOR BELTS IN DIFFERENT TYPES OF PLANT The advantage of conveyor belts compared with other systems is also to be found in the large available service-time window, i.e. the excellent reliability and the low costs of energy consumption and maintenance. It is in particular the reliability of a belt transport system which depends to a great degree on its main component, that is the belt - in all its different types and variations. For this reason, the belt is also given the greatest attention in the development of the individual components, because it is the belt which must be designed optimally with regard to various factors. The specific properties of the conveyor belt then assert a considerable influence on the design and sizing of most other components in a

Jan 1, 1993

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The reliable quality assessment of grouting operations is one of the key issues in establishing impermeable grout curtains around shafts, drifts and tunnels. Reliable opera¬tional information on the decrease in the permeability of rock during the grouting process facilitates the assessment of the effectiveness of the completed curtain and assures production quality. Quality control and assurance also fa¬cilitates the early detection and elimination of possible de¬fects in the grout curtain. Thorough control of the grouting process provides the capability to evaluate decreases in the permeability of water-producing fracture zones prior to the beginning or the continuation of excavation of the shaft, tunnel or drift. In order to achieve this objective, post¬grouting hydrodynamic investigations are conducted prior to the initiation or re-initiation of work on the underground workings to measure the decrease in the permeability coef¬ficient of aquifers during grouting operations. 8.1 QUALITY ASSURANCE AND CONTROL OF THE ISOLATION OF ROCK BY GROUTING THROUGH HOLES DRILLED FROM THE SURFACE Quality assurance and control are based on measuring the decrease in the permeability coefficient of water-pro¬ducing horizons as a result of injecting grout into the drill¬holes. For this purpose, the value of the acceptable residual permeability coefficient is calculated beforehand based on the acceptable value of ground water inflow into the shaft, drift or tunnel as specified by the "construction norm and integrated practice (SNIP)" (Anon., 1976). Having ob¬tained the values of aquifer thickness, permeability, and head distribution for each aquifer from flowmetric data (dis¬cussed in Chapter 3), the average value of the permeability coefficient of all aquifers intersected by the shaft is calcu¬lated as [ ] where Ki is the permeability coefficient of the "ith" aqui¬fer; Pi is the pressure of the "ith" aquifer; and M; is the thickness of the "ith" aquifer. The total expected inflow of ground water into the shaft is [ ] where RK is the radius of the contour of influence; RCFB is the radius of the shaft; and p is the coefficient of dynamic viscosity of the ground water. The necessary reduction of the coefficient of permeabil¬ity of the aquifer [ ] where Q is the expected inflow of ground water into the shaft from eq. 8.2; Q.-fin is the acceptable inflow of ground water; and a is the safety factor. By knowing the average permeability value of the rock and the permeability reduction coefficient, it is possible to determine the value of the acceptable residual permeability coefficient for all the aquifers [ ] The values of the permeability coefficient, pressure, and thickness for each aquifer are determined from the data gathered during the hydrodynamic investigations conducted in grout holes prior to beginning the grouting operations as discussed in Chapter 3. After injecting the grout into the first of the holes, the injection into each of the following grout holes is preceded by repeated hydrodynamic investi¬gations. Using the data obtained for each water-producing zone, a graph is constructed where the numbers representing the grout holes in their order of grouting are placed on the abscissa, and the values of the aquifer permeability coeffi¬cient are placed on the ordinate (Fig. 103). This curve char¬acterizes the change in permeability of the given hydro¬stratigraphic unit as grouting operations are completed, one hole at a time. The results of grouting operations are considered to be positive when each sequential observation records a steady decrease in the permeability of the aquifer. The permeabil¬ity measured prior to the injection of the grout into the last hole must be lower than or equal to the acceptable perme¬ability as determined by the application of eqs. 8.1 through 8.4. Table 8.1 presents illustrative data on the hydrogeo¬logic properties of aquifers at a mine shaft prior to the initiation of grouting operations. Data also are presented on the reduction in the permeability coefficient during the in¬jection of the grout. The shaft in question intersects eleven aquifers. Based on data concerning aquifer pressure, thick¬ness, permeability, and the expected inflow rate of water for each of the strata, the average permeability coefficient is calculated according to eq. 8.1 as K = 0.2 x 10-12 m2. The

Jan 1, 1993

By Earl M. Frizzell, Ronald W. Utley

Introduction For the past several years the Bureau of Mines has undertaken research to develop alternative mine material haulage systems that will improve mine productivity, reduce haulage costs, increase mineral availability, and conserve energy. One basic concept being pursued is a means for crushing primary blasted rock to a size that can be reliably and economically moved on conveyors. During 1980, mine requirements for this equipment and the capability of existing technology to satisfy these requirements were assessed. The study continued into 1981 on the basis that satisfactory equipment for this purpose needed to be developed. The objective of the 1981 program was to perform an engineering design of such a system. A mine survey and equipment development study was conducted in cooperation with the open-pit mining industry by GATX through its subsidiaries, Fuller Co. (a crusher manufacturer) and GARD Inc. (GATX's research and development center), under contract to the USBM. Results of a mine survey in the copper, iron, and molybdenum industries indicated that a universal crusher system could be developed even though details might vary from mine to mine. The crushing characteristics, including tonnages desired, were similar in all surveyed mines. Most mines had similar views about the desirability and frequency of crusher movement. The perceived need for in-nit crushing varied between copper and iron mining. The copper mines felt a greater sense of urgency for introduction of such a system, probably because typically greater vertical haulage is found in copper mines than in the iron mines. All mine personnel surveyed were interested in portable crushers and almost universally preferred gyratory-type primary crushers. They preferred large crushers, citing inherent reliability and durability, and the machine's relative freedom from clogging. Large size minimizes the number of crushers and conveyors needed. Analysis of desired crusher system characteristics (Table 1) fixed the crusher size at 1.5 x 2.3 m (60 x 89 in.). The 1.5-m (60-in.) feed-opening dimension could accept the largest material normally fed to the crusher, and the 2.3-m (894n.) head diameter could fulfill the 3.63 kt/h (4,000 stph) capacity requirement. Selected System Description The comments and analyses discussed in the contract report led to the design and refinement of a movable crusher system. This system represents the consensus of more than 100 mine workers and almost 50 construction and engineering company personnel. It is supported by more than 50 years of experience in crusher manufacturing. Although many alternatives are available for any given system, and selections are likely to be dictated by varying site conditions, the selected system is believed to be appropriate for most projected requirements. Final design would be dictated by mine operators during evaluation for approved projects. Detail design of the feed and discharge systems were not included in the study because they are mine specific. The basic system (Fig. 1) consists of a 1.5 x 2.3-m (60 x 89-in.) gyratory crusher on a structural steel frame. The frame is used as an operating platform for the crusher and as a carriage to move the crusher. The control tower includes a crusher lubrication room, a hydraulic equipment room, a switch gear room, a room for the motor control center, and a control room for operating the crusher and maintaining the equipment. The auxiliary system consists of a hydraulic rock hammer and pedestal crane with 74-t (80-st) and 14-t (15-st) hooks. Figure 1 also shows stairs, railings, and a work platform. Feed and discharge arrangements are shown on Fig. 2. The system shown is for mildclimate applications. Additional enclosure and heating would be needed for extremely cold weather conditions. Crusher A 1.5 x 2.3-m (60 x 89-in.) gyra¬tory crusher was selected for this application. This size can handle the typical throughput of 3-3.63 kt/h (3,500-4,000 stph) desired by the mines and the 1.3-m (50-in.) material to be crushed without difficulty. The crusher is the heaviest

Jan 4, 1983

By W. R. Junge

The investigation, selection, and implementation of remedial activities for large, complex mining and milling sites is dependent on the cost-effective management of tailing and waste materials. Site investigations evaluate the contaminant source areas, assess the potential release rate of contaminants, and determine the acceptable contaminant release rate for the site. Selection of appropriate remedial activities is based on evaluation of constructability, reliability, performance, effectiveness, permanence and cost. Remedial technologies available for tailing and waste material include removal, consolidation, capping and drainage control. Proper implementation and documentation of the selected remedial activities are critical to the overall success or failure of the remedial program. A step-by-step process, established at the initiation of a project, should accurately document all construction activities, monitor environmental conditions at the site, assess the performance of the remedial activities, and, ultimately certify that the remedial activities have met relevant and appropriate standards. Case histories are presented for a uranium mill at Uravan, Colorado and a lead, zinc mine at Gilman, Colorado. These case histories provide examples as to the combination of remedial technologies that have been applied at these specific sites.

Jan 1, 1989

By CORNELIUS STEPHANUS LODEWYK SCHUTTE, WIEHAN ADRIAAN PELSER, JEAN HERMAN VAN LAAR, MICHAEL DAVID HARMSE

Rising electricity costs in South Africa have resulted in a need for optimized compressed-air networks in the mining environment. As a result, the financial benefit of air receivers needs to be reconsidered along with the economic dispatch strategy. This study investigates the use of an evolutionary algorithm in the mining industry to determine the potential financial benefit for various-sized air receivers, as well as their dispatch strategy. A genetic algorithm was selected due to the improved solution reliability and accuracy compared to other optimization techniques. This study indicates that a genetic algorithm can be used to determine the optimal dispatch of compressed air in the deep-level mining industry. Further, this study indicates that air receivers are financially viable in the mining industry and can be used to reduce operating costs, improving profitability.

Dec 1, 2022

By R. E. Utting

INTRODUCTION Until recently, gamma doses had been largely ignored in Ontario uranium mines. This has been due to the assumption that these doses are small and have been more or less unchanged with time and hence their effects have been included automatically in the epidemiological studies that led to the establishment of radon daughter exposure limits. This assumption had to be challenged for two basic reasons. The first was that radon daughter exposures to miners have been progressively reduced over the years due to improved ventilation and ever more stringent regulations, while gamma exposures have presumably remained relatively unchanged. Therefore it must be assumed that the ratio of gamma to radon daughter exposure has gone up. The second reason is more philosophical. It is clearly inappropriate to make judgements on the significance of a potential industrial hazard when the magnitude of that hazard has not been fully assessed. Having decided that some sort of assessment of gamma exposures to uranium miners must be made, it was than necessary to determine how this should be done. Several options were available, for instance: (i) Wholesale personal gamma dosimetry for all mine and mill workers, (ii) Personal gamma dosimetry only for those workers suspected of receiving the higher doses, coupled with area monitoring to estimate the exposures of other workers, (iii) Area monitoring coupled with dose rate times time calculations for all. This would correspond to the generally prevalent method of assessing radon daughter exposures. It was argued that since radon daughter exposures are the major radiological hazard in uranium mines, to invest resources for assessing a lesser hazard to a greater degree of precision was not cost effective. (iv) Since gamma dose rate is related to ore grade, individual doses could be assigned from knowledge of work location and ore grade. Before deciding which of these options would be most appropriate, it was necessary to have some idea of the magnitude of the problem. Very few data were available in the literature and with the exception of a few spot dose rate measurements, and the results of a few gamma dosimeters issued to selected individuals by some of the mining companies, nothing was available. A rule of thumb of obscure origin is often quoted within the industry indicating that gamma dose rates underground will be about 0.25 mR/h per lb/ton or 5 mR/h per % U. This had been used by some to justify neglecting gamma radiation at least for ore grades of the order of 0.1% or 2 lb/ton, on the grounds that gamma dose rates would be of the order of 0.5 mR/h and therefore give rise to annual doses of only about 10 mSv (lrem). That is, it was assumed that gamma radiation was of limited concern compared to the hazard associated with the inhalation of radon daughters. We were thus faced with the situation of just assuming that no regulatory limits were being breached. This situation could not be allowed to continue. A program was initiated to investigate the gamma doses absorbed by uranium miners in three mines in Ontario, and extensive gamma surveys were conducted in the Quirke 2 mine of Rio Algom Ltd, Elliot Lake; Denison Mine, Elliot Lake; and Agnew Lake Mine, Espanola. Negative reaction was received from several mine company officials to the possibility of all miners being required to wear personal gamma dosimeters due to the logistical difficulties involved, and therefore part of the project was aimed at determining if a reliable correlation between gamma dose rate and ore grade in the work location could be deduced, in order that dose rate times time calculations might be used for gamma dose assessments. The results of these programs provided evidence that the gamma dose for some employees in the three mines investigated may be a significant fraction of the current maximum permissible annual dose of 50mSv (5 rem). When combined with radon daughter exposures in the manner recommended by the ICRP at their 1980 Brighton meeting (ICRP 80) the results indicated that some individuals will come close to the resulting limit and may even exceed it. The results also indicate that is probably not feasible to develop a reliable formula for

Jan 1, 1981

By Thomas J. DeMull

Heap leaching was introduced to the precious metals mining industry approximately two decades ago as a simple, low cost method for recovering gold and silver from ores. Since that time, operational experience has contributed to knowledge and understanding of the process, making it a reliable alternative to conventional milling processes for low grade ores. At time of this writing, dozens of heap leach operations are active producing hundreds of thousands of ounces of gold and millions of ounces of silver annually. These successes have caused the popular press to acclaim heap leaching "high-tech" gold mining, but, despite the hype, the process remains a simple one. An example of simplicity in heap leaching is the operation established in 1986 at Amax Gold's Sleeper Mine. Starting with a simple goal, namely to produce gold from sub-mill grade ore at low cost, heap leaching was rapidly implemented at Sleeper; only five months after testwork started, leaching commenced on the first commercial scale, 50,000 ton heap of low grade ore. Sized at 600,000 tons per year to produce 10,500 oz gold per year, the low grade heap operation has performed beyond expectations. During the first year of production, 881,800 tons have been leached producing 15,665 oz of gold and 35,528 oz of silver. Operating ·costs for the first year have averaged $112 per oz gold produced ( or $95 per oz if silver credit is included). Successful implementation of heap leaching at Sleeper has had a dramatic impact on ore reserves and future operations.

Jan 1, 1998

By D. Hodouin

The improvement of mineral processing data using material balance computer programs is nowadays a current practice in many plants, engineering companies or research centers. It now becomes more obvious that such programs should integrate new features such as the preprocessing of data, the estimation of less accessible process variables and an in-depth interpretation of: the computed results. A few solutions to these new problems are already available. The feasibility of a mass balance computation for instance can be examined by analyzing the degree of redundancy of the measurements prior to any data adjustment. New variables such as chemical analyses in particle size intervals or liquid phase composition can be included in a set of measurements. Finally, a sensitivity analysis can be used to analyze the reliability of the results, to detect eventual outliers or to redesign a sampling scheme. Some illustrations of these new developments are presented.

Jan 1, 1989

By B. K. Sternberg

Since 1986, we have developed a series of electromagnetic (EM) sounding systems at the Laboratory for Advanced Subsurface Imaging (LASI). These may be categorized by their frequency ranges: low frequency (LF, 30 Hz to 30 kHz), medium frequency (MF, 1 kHz to 1 MHz), and high frequency (HF, 30 kHz to 30 MHz). We have applied these EM systems to a variety of targets, including: mapping of plumes of contaminated groundwater, tracing leachate for an in-situ leaching operation, locating buried hazardous waste, identifying subsidence-prone zones and detecting buried voids. These systems are also applicable to exploration for ore bodies. Currently, our sounding system uses a vertical magnetic field vector. Previous systems of this type required a slow and relatively inaccurate manual rotation of the sensing coils. The systems also used occasional calibrations of the measuring system. We have developed a 3-dimensional mathematical rotation procedure for the data, as well as a simultaneous, high-accuracy, calibration method. These new developments have greatly increased the speed of the measurements, as well as improving the accuracy of the ellipticity data. We use stepped-frequency measurements along with narrow-band filtering to allow accurate measurements, even in high-noise areas. We typically obtain ellipticity measurements at eleven frequencies and along densely sampled profile lines. We use neural networks to help interpret the measured ellipticity patterns. Neural networks can be trained to relate the measured ellipticity patterns to earth resistivities or to discrete targets buried in the earth. The neural network training may use theoretical EM responses calculated from computer codes for relatively simple structures. The theoretical EM response for many complex targets that are of interest cannot currently be reliably calculated, even with the largest supercomputers available. We have therefore chosen to do some of the training using theoretical EM responses generated in a full-scale modeling tank located at our Avra Valley Geophysical Test Site. We have also developed data-visualization software to help interpret the large data sets produced by this system.

Jan 1, 1997

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine's requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By Victor Romero, Steve Redmond

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2011

By Norbert Patzelt, Johann Knecht

INTRODUCTION Grinding mills have been used in the minerals processing industry for over 100 years. Their dimensions have grown continuously during this time. Besides increasing throughput rates of grinding plants due to the depletion of high grade ores, the lower specific in- vestment costs, as well as reduced operating and maintenance requirements are major reasons for this trend. When selecting new plant equipment one must consider that design principles which have proven their reliability on sizes of today's equipment do not automatically warrant a successful operation on the ever larger size of equipment. Modern calculation methods as for instance the Finite Element method already contribute considerably to the safe design of the huge equipment being built today and are a standard tool of the design engineers. More recently, modern computer programs are also being used in order to size the equipment to meet the process requirements. Today, two design principles are on the market - one which supports the weight of such a unit on trunnion bearings through cast conical endwalls and one which is supported through slipper pad bearings arranged at the circumference of the mill shell (Fig.1). The reason for the development of this alternative grinding mill design can be found in the past. During the sixties and seventies the growing sizes of ball mills with high LID ratios caused many mill failures due to cracked endwalls. The accuracy of the calculation methods as well as the quality standards for castings were not developed to a degree required for such kind of heavy equipment. One way to overcome these problems was the increase of the manufacturing quality standards as well as the introduction of the finite element method based on the analysis of the experience available. The biggest grinding mills being built today are large size SAG mills with cast conical endwalls and trunnion bearings (Fig.2). This is due to the fact that mill manufacturers who had come from the conventional ball mill design adopted these principles as well to their SAG mills. These grinding mills perform well without special concern to the operators. Other manufacturers overcame the problems as mentioned above by eliminating completely the heavy castings and trunnion bearings and the problems associated to it (Fig.1). This design was originally applied to ball mills for the mining and other industries. Due to the success of these shell supported ball mills, this design principle was also applied to SAG mills(Fig.3). Despite of the fact that the majority of today's grinding mills are built to the conventional design it is also interesting to have a look at this alternative. Principles which have proven their reliability on sizes of today's equipment do not automatically warrant a successful operation on the ever larger equipment if bigger mill sizes are realized only based on the pantograph principle. With growing grinding mill sizes, the mass and volume flows through the equipment increases rapidly. Thus it is very important not only to concentrate on the safe design of the structural components of the equipment but as well on the process requirements. The influence of the design on important process parameters of dry and wet grinding plants are discussed thereafter. It shall be shown how modern computer programs can assist in the optimization of the design of components in order to fulfil the operational requirements of such large size equipment. PROCESS REQUIREMENTS OF LARGE SIZE GRINDING MILLS Dry Grinding Mills The world's biggest ball mill is a dry grinding ball mill having a diameter of 6.2m and an overall length of 25,5m with a drive power of 11,200 KW or 15,000HP. This grinding mill dries and grinds gold ore at a rate of 500 tons per hour at a moisture content of up to 9,5%. As shown in Fig.4 this mill was built as a shell supported unit. In fact only this design principle allowed to meet the process requirement. This mill could hardly be built with cast conical endwalls due to the constraints of the trunnion bearings limiting the mill inlet. The following case shows how modern computer programs can help to meet the design criteria of the air system of large size dry grinding plants. For dry grinding plants, the gas flow through the SAG mill has to match the drying, as well as the material transportation require-

Jan 1, 1998

By K. Hajmrle

The production of nickel coated mica composite powder by hydrogen reduction of a nickel ammine sulphate solution, followed by the production of molded plastic samples containing Ni/Mica is described. Sample preparation by injection or compression molding is outlined and the better results in compression molding are explained by the combination of better particle-to-particle contact, less particle breakage during processing, and more random particle distribution in the plastic. Three volume resistivity measurement techniques are described and compared. Two of them (conductive paint and silver-rubber electrodes) are found reliable and are used throughout the work. The influence of nickel content and particle size of Ni/Mica on volume resistivity is evaluated and the optimum product defined. One of the most important assets of Ni/Mica, its ease of injection molding, is demonstrated by the good electrical properties obtained with little optimization of the injection molding process. Surface roughness of molded plastics with and without Ni/Mica is briefly discussed. Shielding effectiveness of Ni/Mica in four plastics (PP, ABS, PBT and PC) is presented and correlated to volume resistivity data for the same materials. The addition of 15 to 50 weight % Ni/Mica (3 to 16 volume %) to plastics and subsequent injection or compression molding produces composite materials having low volume resistivities (0.03 to 1 ohm.cm) and high shielding effectiveness (40 to 70 dB).

Jan 1, 1988

"Caterpillar has developed the Cat GH800B longwall plow system, designed for mining very low coal seams at high rates. Building on the attributes of the proven GH1600 plow system, the Caterpillar longwall team in Lünen, Germany, worked with the German Ibbenbüren Mine to design and construct a system for mining an anthracite seam averaging only 0.85 m (33.5 in.) thick. The result is the GH800B plow and associated longwall system, which is now operating in the Ibbenbüren Mine - where the seam does not exceed 1 m (39 in.) in height.The Cat GH800 plow, with an installed power of 2 x 400 kW, has been the plow of choice for seam heights from 0.9 to 2 m (35 to 78 in.), regardless of seam inclination or coal hardness. But the lower the coal seam, the more difficult the extraction process. Flexibility, reliability, efficiency and serviceability of the whole system had to be refined for maximum productivity in such a minimal height, but several key modifications led to success.The armored face conveyor (AFC) modifications for the GH800B plow system include PF4 plow line pans with a replaceable top trough and a new plow guide made of a one-piece casting to provide extra strength and durability while being lower in height than the previous welded version. External dogbone connectors between the line pans and a strong and flexible relay bar between the AFC and the roof supports (shields) further adapt the conveyor for very low seam operation. To increase coal throughput, the engineering team widened the conveyor crosssection with extended side plates."

Jan 1, 2014

By P. Gelfi, J. Vanderbeek, J. Enriquez

"The Cerro Verde copper-molybdenum mining complex is located near Arequipa, Peru. A 108,000 t/d copper concentrator (C1 concentrator) commenced operation in late 2006 and was debottlenecked to a 120,000 t/d capacity in 2011. A feasibility study, initiated in May 2010, assessed the potential for expanding the processing rate of the large Cerro Verde sulfide reserve via the installation of a second, stand-alone, concentrator (C2 concentrator) capable of processing a nominal 240,000 t/d ore. The feasibility study was successful and the project advanced through engineering, permitting and construction. Ramp up to nameplate capacity was ahead of schedule. The overall project was completed on schedule and within budget. The details of the project and supporting components are described. The design philosophy and design basis of the concentrator facilities are discussed as are factors that influenced the concentrator layout. Risk mitigation features included in the design are reviewed. The factors that drove the successful and rapid ramp up to nameplate capacity are discussed. Operational experiences in the first year of plant operation and project lessons learned are described. INTRODUCTION/BACKGROUND Sociedad Minera Cerro Verde S.A.A. (SMCV) operates a copper mine near Arequipa in southern Peru. Small scale operations operated intermittently until 1970 when the deposit reverted to the ownership of Minero Perú S.A (Peruvian government). Minero Perú S.A. commenced mining and processing of oxide reserves in 1972 and placed an SX-EW plant into production in 1976. The ownership of the property has changed hands several times over the years. Minero Perú sold Cerro Verde to Cyprus Climax Metals in 1994. Cyprus was acquired by Phelps Dodge in 1999. Freeport-McMoRan (FCX) acquired Phelps Dodge in 2007. Several studies were undertaken during the 1990’s that tried to establish the economic justification to process the large primary sulfide resource that underlies the surface oxide deposit. None of these studies produced an economic conclusion until a feasibility study was completed by Phelps Dodge and SMCV in 2004. This study provided the economic justification for the construction of a 108,000 t/d concentrator during 2005 and 2006. The key to the success of this study was identifying a water source that was sufficient to support processing economies of scale. Concentrator operations commenced in late 2006. The original design production rate of 108,000 t/d was achieved on a 30 day moving average basis on the 266th day after ore was first introduced. During 2009, studies and evaluations were performed that had the objective of addressing observed concentrator bottlenecks to allow a production rate of 120,000 t/d to be achieved. The 120,000 t/d figure represents the sustainable production limits associated with the installed primary crusher and tailing thickeners which would have been prohibitively expensive to upgrade. Debottlenecking activities were implemented during 2010 allowing sustained production rates of 120,000 t/d to be achieved."

Jan 1, 2017