Search Documents

By R. V. Ramani, W. Miola

The MSHA prescribed method for the determination of quartz in airborne respirable-dust samples from underground coal mines is the P-7 method, a combination of low-temperature, radio-frequency ashing (LTA) and infrared analysis (IR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive infrared (IR), Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) methods are most commonly used for the analysis of quartz in powders. Several aspects of the experimental procedures, such as the preparation of the analysis sample from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist and data interpretation, affect the results from each of the methods differently. Significant differences in analytical results obtained from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All studies point to the need for reliable quartz analysis methods. In a recent research program, a procedure for preparing bulk-coal and host-rock samples for quantitative quartz analysis was developed. Further, the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle-size distribution, matrix and calibration on the analytical results. In this paper, several issues concerning the measurement of quartz in the samples of coal, host-rock and airborne respirable dust from mines are outlined and quantified.

Jan 1, 1996

By Allan E. Hall, Stephen G. Hardcastle, Lucien D. Nel, Jean-Paul Saindon

A description is given of the investigation conducted at Sherritt Gordon's Ruttan Operation in Manitoba during 1986. Gas and dust concentrations were measured in the exhaust air of the major working sections to assess the potential for recirculating exhaust air into the intake air in winter to reduce heating costs. The results indicate that there is excellent potential to significantly reduce winter heating costs by controlled recirculation of exhaust air. Gas and dust concentrations vary significantly during the working shifts but have consistent trends from shift to shift and day to day. The variations in gas concentrations have similar trends but no single gas could be reliably used to predict the variation of the other gas or the dust concentrations. Dilution and the other effects which reduce pollutant levels as the exhaust air returns to surface indicate that recirculation should take place as close to surface as possible, subject to the economic constraints of the airway construction required and the extra fan energy required for the longer recirculation path. Recommendations are made for the choice and positioning of air and dust monitoring sensors and the logic of a control system. Economic analysis of the results indicates that controlled recirculation is viable at an existing mine with a pay back period of approximately two years. Incorporation of a system into a new mine at the planning stage would significantly shorten the pay back period.

Jan 1, 1987

By Isobel Clark

The problem of the estimation of ore reserves is essentially a simple one to describe. Given a set of sample data, at specified locations within a deposit, how can we estimate the value (or quantity) of ore in unsampled areas. The question may be posed of a whole deposit (global) or it may be more desirable to estimate smaller volumes within the planned mine area, e.g. stopes or blocks (local). Many methods have been evolved to tackle this problem, from hand-contouring of values by the mine geologist to extremely sophisticated geomathematical analysis. The main difficulty with any estimation method in this context is that it is almost impossible to check whether the "predicted" value bears a close relationship with the "actual" value. The only reliable way to decide if an estimation method has "worked" is to test the eventual value of ore against the predicted value. This is, more often than not, impossible - even allowing for the time factor involved. To know the "actual" value of a mined block it has to be sampled intensely, and these values with their positions recorded accurately. Alternatively, blocks may be passed through the concentration process individually and these results recorded. In most producing mines neither of these alternatives are practicable or seen to be-important. Another problem with comparing in-situ (so-called) mineable reserves with production figures is the introduction of many variables into the concentration process -- dilution, wastage, possible stockpiling, mill recoveries and so on.

Jan 1, 1979

By Roberto Zaragoza

Historically, the control of flotation operations has been viewed by many as an art. Only recently has process measurement and control come to be viewed not as an ?art? but as a very complex and productive science. In recent years, process control applications to flotation plants have been established and already some gains have been reported for several industrial operations using individual stabilizing control loops including level, pulp flow, pulp density, reagent addition rate and pH (Paakinen, 1979; Hales, 1985). The use of process control computers combined with on-line x-ray florescence (XRF) in industrial flotation circuits has made the application of more sophisticated control techniques feasible in the mineral recovery process. In spite of the availability of reliable instrumentation in modern flotation plants, satisfactory control strategies are difficult to develop and implement. Extremely important factors such as changes in ore type, liberation characteristics, flotability, degree of oxidation on particle surfaces, and specific gravity constitute unmeasured disturbances to the process. Most current control systems cannot adapt specifically to such disturbances.

Jan 1, 1987

The concept of optical basicity is now being widely applied to rationalize and predict the chemical properties of slags. It employs signals from a probe ion to indicate the "state" or relative "freeness" of the oxygen ions in the slag, and hence provides a fundamental measure of slag basicity. Values of the bulk optical basicity of a slag can either be measured spectroscopically in samples of transparent solid glassy slag, or calculated very simply and accurately from the chemical composition of the slag. The way in which these values vary in different systems are illustrated as isoptical basicity lines on ternary diagrams, and the patterns obtained are discussed. The difficulties associated with assigning optical basicities to the oxides of transition elements are also reviewed briefly. It has been demonstrated that these bulk values can be used as the basis of a flux control model for steelmaking to achieve end-point chemistries much more reliably. Furthermore, several correlations have been established which allow the prediction of the slag-metal distribution of various solute elements. This approach has been used to predict the phosphorus distribution at the end of steelmaking, and also to custom design fluxes for the ladle and tundish to aid in the control of residual elements in the steel such as suphur, hydrogen and nitrogen.

Jan 1, 1990

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001

By Larry S. Diaz

The paper considers the selection of control instrumentation for a modern flotation plant, as well as the best interpretation and most effective use of the process data obtained. Process control computer availability is considered from the outset. A general philosophy of control is proposed which leads toward a system that is its own reliability monitor. The bulk of the problems are in grinding and classification. Alternative control methods are described that use particle size measuring devices. Flotation controls, based to a large extent upon on-stream X-ray analysis, are reviewed in detail. Reagent control methods are also examined. Methods to analyze the data obtained from the various measurement devices are introduced. These methods would enable an estimate of the validity of the data and require some redundant information. Another objective of these methods is the protection of operating equipment from possible control malfunctions. Although the discussion generally considers some degree of computer usage, this paper attempts to describe instrumentation and data analysis methods that enable control with or without the process control computer.

Jan 1, 1972

By Stewart W. Daniel

Competitive pressures involving product duality, uniformity and economics are increasing the interest in and accelerating' the adoption of automation by the cement industry. The demands of this industry on instrumentation and control manufacturers for more effective and reliable control of process variables is also increasing. The trend to replacing small grinding mills with a fewer number of larger mills is lowering the investment requirement per unit of capacity both for the mills and for their automation. Cement process control systems of today are more sophisticated than the equipment installed two or three years ago, not because the process itself is more complex but because todays demands require a higher degree of control action and accuracy. Because of increasing labor costs, an important objective of an automation program is a reduction in the process labor content. This can be realized by allowing the operator free time for other duties, by increasing the number of grinding circuits one operator can supervise and by removing to. a large extent the need for the operator to make process' adjustment decisions.

Jan 1, 1965

A group of geologists is located in a remote area of North America, without telephone lines, electricity or even running water. They have spent days accumulating data for a mining company that is eager to receive any information about the dig. But the team does not have access to a wired communications infrastructure. So the geologists must wait until they get to the nearest town to transmit their data. TMI Communications has a mobile satellite communication system that allows geologists in the field to transmit their data from remote locations. The company's satellite is the heart of its North American mobile communications network. This satellite turns all of North America, including Canada, Mexico and the Caribbean into a single digital communications cell. Traditional terrestrial communications systems, such as dedicated phone lines or cellular systems, cannot handle a remote geological exploration camp's extensive communications needs. Cellular technology, where available, has high costs and limited applications. For geologists in the isolated areas of North America, accessible and reliable phone service is vital to success. For those who have established temporary camps, TMI Communications' satellite phone service has improved the speed and accuracy of their communications with home base. This wireless network is suited to meet the needs of existing data applications and the challenges of new ones. It can support any one- or two-way, fixed or mobile data transfer. TMI's network enables geologists to transmit exploration results, spreadsheet information and location co- ordinates to anywhere in the world, at any time. This is important if a team needs to relay vital data back to its headquarters to support immediate decision making on a prospect site or a find.

Jan 1, 1999

By John G. Viets, J. Robert Clark

A multielement extraction system is being used successfully to provide essentially interference-free geochemical analyses to aid in gold exploration. The Methyl isobutyl ketone-Amine synerGistic Iodide Complex (MAGIC) extraction system separates Ag, As, Au, Bi, Cd, Cu, Ga, Hg, In, Mo, Pb, Pd, Pt, Sb, Se, Sn, Te, T1, and Zn from interfering geological matrices. Quantitative extraction of these elements is accomplished over a broad range of acid normality, making it possible to economically determine all 19 elements from a single digestion or leach solution. The resulting organic extracts are amenable to analysis by inductively coupled plasma atomic emission spectroscopy (ICP-AES) and flame atomic absorption spectroscopy (FAAS). For many years the principal shortcoming of ICP-AES was the complex spectral and stray-light interferences that were caused by the extreme variability of components such as Fe. Na, and Ca in common geological matrices. The MAGIC extraction allows determination of the extracted elements with enhanced sensitivity, from a virtually uniform matrix, by ICP-AES and FAAS. Because of its simultaneous multichannel capabilities, ICP-AES is the ideal instrumental technique for determining these 19 extracted elements. Ultratrace (sub-part-per-billion) determinations of Au and many of the other extracted elements can be made by graphite furnace atomic absorption spectroscopy (GFAAS), following back stripping of the extracts. The combination of the extraction followed by stripping of the organic phase eliminates 99.999% of potential interferences for Au. Gold determination by GFAAS from these extracts under the specified conditions yields a fourfold improvement in sensitivity over conventional GFAAS methods. This sensitivity enhancement and the interference-free matrix allow highly reliable determinations well into the parts-per-trillion range.

Jan 1, 1990

By Richard Keith Corbin

INTRODUCTION The purpose of this paper is to assist explorationists and entrepreneurs in deciding whether to invest in gold mining concessions in lesser developed countries (LDCs) and, if so, in deciding which LDCs provide the best opportunity. The first decision is difficult in the face of common notions that foreigners are not welcome - only their money; that the best gold deposits were worked out long ago; that even if you survive the mal- aria, and in spite of 51% control by a national partner, you manage to profit from a new discovery, they will tax your operation to death, or worse yet, nationalize it. Close scrutiny of what happened to foreign investors in LDCs during the “Mexicanizationt” of the 1930's through the "Zambianization" of the 1970's shows that many of these concerns are well-founded historically. But the trend of knowledgeable writers over the past decade seems to be away from this gloomy foreboding, and towards a cautious optimism, based on recently perceptible metamorphoses in certain LDCs' conditions and attitudes. If the explorationist or entrepreneur decides to seize on this apparent opportunity, the second decision -- which of these certain LDCs to invest in -- is doubly difficult, because of the formidable tasks of coming up with a rating system to provide rational comparison, and then gathering enough current, reliable information to apply. To assist in these tasks, a suggested rating system and case studies, respectively, follow a brief review of recent writings on the subject

Jan 1, 1987

By D. M. Kjos

Large-diameter autogenous and semiautogenous grinding mills represent the primary thrust of the expanding grinding technology. In spite of initial difficulties, large autogenous and semiautogenous mills have reached an acceptable level of technology that provides the mineral engineer with a reliable, low cost means of ore comminution. A successful milling installation begins during the design stage of the grinding mill and the plant in which it is to be installed. This is particularly true in autogenous and semiautogenous mills. Critical mill and plant design factors should be considered while the mill and installation are still only "paper." Various current liner designs will be discussed ranging from lifter bar/plate to integral types. Modes of operation such as "high-low" will be considered. Liner maintenance procedures ranging from laydown area in plant design, proper mill shutdown methods, to installation and bolt tightening complete the equation to yield optimum performance possible for any particular grinding application. The objective of this paper is to discuss trends in wear materials, designs, and operating practices, and to provide some guidelines for good practice as we move through the 1980s. We will put together concepts that relate to the designs, materials, and applications so that higher performance can be obtained by the operator for his specific application. The concepts are shown as being in series became they are dependent on each other to achieve the desired performance: designs times materials times application results in higher performance (Arnson, Parks, and Kjos, 1983).

Jan 1, 1987

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By W. R. Peters

An experimental hole-to-hole seismic probe system has been developed for use in coal measure geology as a means of determining the structural conditions of coal seams. The source probe produces a 500-joule electric arc discharge whose seismic wavelet has a spectrum in the 200 to 2,000 Hz frequency range. Low compliance hydrophones contained in the source probe as well as in a separate seismic detector probe are matched to the frequency range of the source. Both probes are constructed with 5-72 cm diameter housings. The transducers in the probes are equipped with fluid-inflatable boots to permit operation in either wet or dry boreholes. Preliminary tests in vertical boreholes drilled 213 m apart in sedimentary rock formations show reliable operation and useful seismic propagation measurements along horizontal and oblique paths up to 232 m in length. Because the seismic wave- let has an accurately repeatable waveshape, multiple shots and signal averaging techniques can be used to enhance the signal-to-noise ratio and extend the transmission distances.

Jan 1, 1985

By Kenneth J. Reid

The application of computers for control purposes in hydrometallurgical processes is not as well-established as in mineral processing plants. This is not only due to the comparatively new development of large-scale application of hydrometallurgy and the relatively small number of operating plants, but also due to some of the basic dynamic characteristics of hydro- metallurgical processes., Basically there is little difference in the development and application of digital control techniques in hydrometallurgical plants from those techniques widely in use throughout the chemical process industry and in nonslurry applications; particularly for those cases involving liquid streams only, the primary sensing elements are essentially the same. On-stream X-ray fluorescence analysis is a well-established method for determination of metal content in the process streams, and standard equipment is used for the measurement and control of pH, flow, density, temperature, pressure, and other variables. Nevertheless, the high proportion of corrosive slurry streams at elevated temperature and pressure poses a challenge to the instrument engineer concerned with developing long-life, reliable instrumentation. One major difference and potential problem area in developing control systems for hydro- metallurgical processes is related to the very long time constants which are common in the larger plant. In these circumstances, it is important to define the overall control objectives very carefully and be prepared to allow for considerable drift in intermediate variables. In larger projects with many control loops the general advantage of lower costs compared to conventional analog instrumentation can be confidently expected. Also in most cases, the process analysis necessary to design and specify a comprehensive computer control system and the increased operator involvement in implementing digital control systems yield additional benefits due to the increased understanding of the dynamic characteristics of the process.

Jan 1, 1979

By Andrew Mackenzie, Paul Rantala

Data is now appearing in literature that indicates many current paste fill systems in Canada suffer from plugged lines and severe wear rates. Both of these conditions suggest: design problems with the pipe distribution system, backfill composed of poorly graded material and/or possibly poor operator practices. Problems that can be prevented in the design stage, but still may be readily solvable with current technology. However, if left untreated will lead to an increasing frequency of down time. The compatibility of the distribution system with the paste fill rheology is fundamental and essential for the reliable delivery of fill. Either many mine operators are not familiar enough with the technology to provide a critical review that could foresee problems down the road, prior to construction and or North American designers are not clarifying their designs to their customers. The objective of this paper is to highlight key concepts to mine operators with the purpose of better enabling a critical review of contractor's/consultant's designs. There is a great deal of understanding about the rheology of backfill over a range of pulp densities from hydraulic slurry to dense to paste. However, outside of deep mines (especially in South Africa) neither hydraulic or dense fill distribution systems have suffered the problems of paste fill. Paste fill is fundamentally different from hydraulic fill principally in its transportation characteristics. These differences have a direct impact on the design of the distribution system. By understanding the practical implications of these differences the operator can play a more active role in their design while better appreciating how to best operate their own system.

Jan 1, 2001

By K. E. Hjelmstad, W. H. Pomroy

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage. Recent research by the US Bureau of Mines has established the feasibility of ultralow frequency electromagnetic signaling for underground mine fire warning. Infield testing completed thus far at five mines, signals of from 630 Hz to 2000 Hz were transmitted through rock up to distances of 1645 m (5400 ft) to a pencil-sized ferrite-core receiving antenna and intrinsically safe receiver circuit. Theoretical analysis indicates a capability to transmit effectively for distances in excess of the maximum depths of most American mines, which is about 900 to 1000 m (2950 to 3280 ft) . The prototype system uses off-the-shelf components and state-of-the-art technology to ensure high reliability and low cost. This technology would enable simultaneous and instantaneous warning of all underground personnel, thereby in- creasing the likelihood of successfully evacuating a mine during a disaster. This report discusses the theoretical basis for through-the-rock ultralow frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 1991

By Kugan Kuganathan

Pastefill is being increasingly considered as a viable fill by underground mine operators. Mount Isa Mines (MIM) chose pastefill to fill their deep copper mine (>1200m deep) after considering various other types of fill in the feasibility studies. During the development of pastefill at Mount Isa (1996 - to date) the Mining research of MIM developed two cost effective, reliable and simple testing methods and used. With the help of these tests the behaviour of MIM pastefill was studied thoroughly and the most optimum mix design for pastefill was achieved. The MIM's pastefill plant, the largest in the world with a capacity of 450rph continuous pastefill production and unique in the process used, has been built (1998-1999) to produce pastefill to the specification developed through extensive testing program using the Flow Cone and Mini Slump cone Tests. As a consequence, it is now possible to select the optimum pastefill mix designs and predict their flow behaviour in bore holes or pipe lines using only these tests. MIM Blended Tailings Pastefill (BTPF) uses 3-3.55 Portland cement and the cost of pastefill is much lower than the total tailings pastefill, that could be produced from the same tailings.

Jan 1, 2001

By d&apos, I. J. Agati

The stockpiling and reclaiming of bulk materials can be a challenging task for engineers seeking the optimum solution for plant needs, reliability, and at lowest unit cost. The objective of this paper will be to expose advantages, disadvantages and limitations of many storage and reclaiming systems to the responsible engineer and management. The paper will emphasize the practical aspect of stockpiling and reclaiming methods. Many valuable and interesting papers are available dealing with the theoretical viewpoint and application of a particular manufacturer's machine. Several of these are mentioned in the bibliography. As many practical parameters as possible will be given. After twenty years in the field of designing and selling bulk materials handling systems, the needs of the user and the plant are recognized and reasonably understood. This paper cannot give solutions to all problems In this vast field but will stress practical applications and examples of various installations. The evolution of advancements in materials handling is based upon not only technological innovations, but learning from many experiences of others and utilizing them as stepping stones to improved installations.

Jan 1, 1969

By Steve L. Bessinger, Luis B. Giraldo, Joram Shenhar, James D. Pile

This paper discusses the Helical Drag Bit (HDB) and its rock drilling applications with an emphasis on use in mining operations. The HDB is a drilling tool that employs cutting members arranged in a pattern to form a helical groove or thread within a borehole. This pattern of cutters can be used for several purposes including roof bolting in mining, interpretation of the lithology of the strata being drilled and low energy consumption drilling. Laboratory and field experiments have consistently shown increase of roof bolt-anchoring capacities in weak rock of more than 100% using the short encapsulation pull test method when boreholes are conditioned using the HDB. In 2004 a series of tests conducted in mines with weak roofs demonstrated the benefits of HDB technology for roof bolting applications in mining. HDB technology offers opportunities for new and beneficial approaches to interpret the geology of roof strata. During conventional drilling, traditional approaches to determine rock properties require simultaneous measurement of several parameters such as thrust, rotational velocity, torque and penetration rate. The unique geometry of the HDB possesses a characteristic that allows determination of the mechanical properties of the rock being drilled by measuring torque as a single drilling parameter. This capability greatly simplifies the process of determining rock properties and provides reliable results. Additionally, HDB technology has been demonstrated to offer significant advantages for rock drilling. A substantial portion of the rock is removed by the fracturing of the internal thread created in the rock bore by the tool taking advantage of the weakness of the rock in tension. Because the rock chips obtained in this process are relatively large, savings in energy are realized when compared to traditional drilling technologies.

Jan 1, 2005