Search Documents

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides: chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 1000 to 150°C. The rate of dissolution of chalcopyrite becomes so rapid under these conditions that the rate of recovery is no longer limited by the rate of chalcopyrite dissolution, but by the degree of exposure and other factors. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, size of sulfide particles, and fraction of sulfide exposed to solution.

Jan 1, 1972

By P. H. S. W. Kulatilake

The presence of discontinuities strongly affects the mechanical and hydraulic behavior of rock masses. Joint geometry networks play a vital role in civil, mining, and petroleum engineering projects associated with jointed rock. The need for a realistic representation of joint geometry in rock masses has been recognized. The first part of the paper shows how to build three-dimensional stochastic joint network schemes and also shows how to perform validation studies for these schemes using joint data from the Stripa mine, Sweden. Due to the existence of complex joint patterns, mechanical behavior of jointed rock masses usually exhibit scale effects and an-isotropic properties. A correct understanding of the mechanical properties (strength and deformability) of jointed rock masses is important for designing and performance estimation of structures build in and on rock masses. Beyond a certain volume, the mass proper-ties of the rock may remain essentially constant with respect to the effect of joints. This minimum volume may be used as the element size to represent the equivalent properties of a statistically homogeneous rock mass volume which contains a significant number of joints. This volume may be termed as a "Representative Elementary Volume" (REV) and may be of great importance for engineering purposes. Investigations are underway at both the 2D and 3D levels to look into the possibility of establishing relationships between REV mechanical properties and joint geometry parameters. Recently developed joint geometry modeling schemes are linked with existing distinct element codes (both 2D and 3D) to create a stochastic/deterministic stress analysis approach in achieving the goal. Results obtained so far in this direction are presented in the second part of the paper.

Jan 1, 1992

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By C. Patrick

Annually, the U.S. coal industry generates and must dispose of over 200 million tons of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks, used for under-ground ventilation stoppings, with refuse blocks. Refuse was collected from three active preparation plants in Eastern Kentucky and used as the primary aggregate for concrete cylinders. The refuse fell within ranges normally observed for size consist, moisture, and ash. Stress-strain analyses yielded compressive strengths of the refuse cylinders from 59% to 77% of the control group strengths. Low variability within groups while significant differences between groups were found. On-going determination of effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1995

By C. Gregory Knight

Adequate planning for the development, operation, and reclamation of a surface mine requires attention to present and future uses of land, both on the mine site and in the mine vicinity. This paper outlines land use implications of surface mining, and suggests procedures that could link mine planning, mine operation, and reclamation to more general land use concerns. Mining is viewed as a temporary use of land that may irretrievably commit land resources away from some future activities, but may allow other uses, some of which may have been impossible without mining. The paper accepts the premise that surface mining should attempt to minimize environ-mental damage and to maximize future alternative uses of land by appropriate reclamation. I. The Effect of Surface 1'1ining on Land Use Surface mining is a temporary utilization of the land most often criticized because the disturbances it creates are of far greater duration than the actual extractive operation, Resource recovery disrupts existing activity on the land, at least temporarily, and

Jan 1, 1977

By Fengmei Chen, Na Liu, Bingrui Li

A quantitative analysis method based on the airflow influence factors is proposed to evaluate airflow stability and discriminate airflow directions in complex ventilation networks. The law governing the changes in airflow caused by changes in branch resistance is revealed based on simulations of the airflow state in a ventilation network and a statistical analysis of the results. Then, three evaluation indices (airflow sensitivity, airflow influence factor, and critical airflow) are determined, matrices of the airflow influence factors and critical airflows are constructed, and a quantitative evaluation method for ventilation system stability and an airflow directional discriminant are proposed. The results show that the stability of a ventilation system can be reliably evaluated based on the airflow influence factors. The sensitive branches and dominant branches in the ventilation network can be determined based on the matrix of airflow influence factors, and the reversed branches, the trigger branches, and the reversal conditions can be determined based on the critical airflow matrix and the matrix of airflow influence factors. The proposed airflow directional discriminant is suitable for evaluating arbitrarily complex networks.

Nov 15, 2023

By K. Feledi

"A booster fan is an underground mechanical ventilation equipment installed in series with a main surface fan that is used to boost the air pressure provided by the surface main fan passing through it. As mining continues to expand and go deeper, the need for improved and efficient ventilation increases. This has led to the use of booster fans and other auxiliary ventilation devices in underground mines. This paper details experiments and results carried out at Missouri S&T Experimental Mine that investigated air leakage and recirculation caused by the use of booster fans. The results were compared with the situations where booster fans are used and not used.The variables considered were the booster fan blade angle and the fan combinations. Air quantity measurements were taken at each individual stopping under a number of scenarios and across four blade angle settings. The first set of situations examined were; the main surface Joy fan only running, the main Joy, and the west booster fan running, and the main Joy fan and east booster fan running. Observations were made which lead to the conclusion from the experimental analysis that booster fans affect the behavior of leakage and recirculation. The locations of the booster fan and the blade angle setting have the most effect on leakage and recirculation. To limit the potential for system leakage and recirculation, the location and size of a booster fan in a ventilation system should be thoroughly evaluated.INTRODUCTION Missouri S&T Experimental Mine ventilation system The Missouri S&T Experimental Mine has two shafts. One currently serves as the main intake shaft. Air is forced through the main shaft by a Joy Manufacturing Vane Axial fan and follows the direction shown on the map on Figure 1. The air is currently naturally exhausted through the Wheeler portal. As indicated on the map there are eight stoppings in the mine, with stoppings number 2 and 8 fitted with man doors. The mine also consists of three raises which are either fully or partially blocked, two portals with one acting as an exhaust and the other generally closed by a hydraulic Kennedy door."

Jan 1, 2015

By Valerie (Wollet) Rebar

Successful execution of fast-track projects is an arduous task at best. Effective and organized management, a comprehensive technical design with an independent check-and-balance system, and optimal schedule components all play major roles in project success, regardless of the required timeline. However, a fast-track schedule intensifies the significance of each of these elements due to the heightened time constraints.

Jan 1, 2008

By S. F. Willey

The difficulties encountered in justifying replacements for over-age mobile mine equipment at the Gay Mine are common to most mining operations. More critical management reviews, resulting from ever rising capital expenses, increased such difficulties. These increased difficulties are especially apparent to those who are primarily operators and are not statisticians, mathematicians, or computer oriented. The Gay Mine is located 17 miles east of the town of Fort Hall in southern Idaho. This open pit operation annually supplies the J. R. Simplot Company and the FMC Corporation with 1.5 MM - 2.0 MM tons of phosphate ore. Stripping ratios average approximately three bank cubic yards of waste per ton of ore mined. The mobile mine equipment fleet consists of ten 24 yard scrapers; twenty-one 30-50 ton end dump trucks; four 32 42 yard shovels; fifteen dozers in the D-8 and D-9 classes; and three road patrols. Equipment replacement is based on the results of evaluations made on individual units. Authorization of capital expenditures for equipment replacement is dependent upon a favorable profitability index (true rate of return on investment) plus a favorable payout time. The system is based on cash flows and requires the determination of (1) the net cash outflows in the form of capital expenses plus (2) the expected cash inflows resulting from reduced expenses and depreciation tax credits. After adjustments for taxes and the time value of money, the net amounts are used to calculate the required indices. The basic elements for the system related to the replacement of mobile mine equipment include: (1) the determination of dollar penalties to be expected from the continued use of aging equipment; (2) the selection of equipment that will provide the greatest return on the investment dollars; (3) the quantification of the expected savings; and (4) the calculations of the prescribed indices. Inadequacies inherent in previous evaluating methods led to the search for more

Jan 1, 1972

By E. D. Sehnke

The refractory materials industry provides the largest commercial market for nonmetallurgical grade bauxite. Refractory grade bauxite is prepared from bauxites having low iron, titania, and alkali content by calcining at temperatures near 1,650° C. Although there are substantial bauxite reserves in the world, premium grade bauxite ores suitable for use in refractory applications are limited to only a few specific sources, primarily in Guyana and the People's Republic of China. Consumption of bauxite for refractory use is closely associated with the production and consumption of primary metals, in particular iron and steel. Barring major disruptions within the principal producer nations, sufficient supplies of refractory bauxite will be available to meet world demand well into the next century, and raw material costs will continue to determine the availability of markets for bauxite-based refractory products.

Jan 1, 1992

By F. V. Antonio, R. S. Pizarro

Masbate Gold Mines, dormant since WWI I, are now back in operation. The ore treatment plant incorporates carbon-in-pulp processing, utilized because of the ready availability of coconut shell charcoal in the Philippines and the high clay content of the ore. A detailed description of the plant, including the surprisingly fast and efficient alcohol stripping facility is presented. Operating data for the plant is provided together with an interesting performance evaluation of mechanical versus air- lift agitated leach tanks.

Jan 1, 1981

By H. R. Hernandez-Guerrero, S. A. Robles-Salazar, M. Marín-Pasillas, P. J. Pompilla-Rosales

Peña Colorada is a company dedicated to the exploration, exploitation, and beneficiation of iron ore, serving the national steel industry. Established in 1975 as a stateowned enterprise, it transitioned to operating as a private organization in 1991. It is jointly owned by two investors, ArcelorMittal and Ternium, each holding a 50% stake. The mining operation is situated in the municipality of Minatitlan, in the northwestern part of the state of Colima, Mexico (Figure 1). It comprises an open pit mine and a concentrator, covering an area of approximately 2,300 hectares. The pellet mill is in the town of Manzanillo, Colima state, a port on the Pacific coast, about 46 km southwest of the mine. The pellet mill occupies its own property with a total area of 60.4 hectares. A gravity-driven concentrated slurry pipeline connects the mine and the pelletizing plant, located at an average elevation of 1,020 meters above sea level and 20 meters above sea level, respectively. Currently, Peña Colorada produces 4.1 million tons of pellets and 0.4 million tons of iron concentrate annually. In 2018, due to a change in the cutoff grade, the processing volume of the beneficiation plant increased from 9 million tons to 16 million tons annually. This led to a greater amount of information to process and characterize the ore extracted from the pit before its processing in the beneficiation plant. Consequently, Peña Colorada sought new ore control technologies to enhance ore selection, optimize human resources and data management, as well as minimize discrepancies between planning and execution. To ensure adherence to quality agreements with stakeholders, it is crucial to understand the ore characteristics before initiating mining activities.

Feb 1, 2024

Teeter-bed (i.e., hindered-bed) separators are used throughout the mineral processing industry for both classification and density separation. The high capacity and sizing characteristics of these units make them ideal for feed preparation prior to coarse flotation (+0.100 mm) circuits. Teeter-bed separators are typically easy to control with two basic operating parameters including fluidization water rate and bed level. However, data show that these two parameters greatly interact with one another. Given this finding, a high-level automatic control scheme was developed and implemented on a full-scale separator. In addition, dialogue with plant operators has led to several simple changes to an already established design that improves operational and maintenance characteristics.

Jan 1, 2010

By M. R. Grundy

The Robinson project is based on the porphyry copper and gold deposits in the Robinson Mining District, near Ely in Eastern Nevada. The district was mined from the late nineteenth century to 1978 by Kennecott Copper Corporation and its predecessors. Operations ceased when falling copper prices in the late 1970's made their outdated mill and smelter complex at McGill uneconomical. In October 1991, Magma Copper Company (Magma) acquired the many claims that cover the known porphyry copper deposits in the district These occupy a disturbed area about nine miles long and three miles wide between the towns of Ely and Ruth. Magma proposes to build a copper / gold mine and concentrator and expand the existing gold leaching facilities. Several pits, previously mined by Kennecott Copper Corporation, will be enlarged; the use of larger, more modem equipment will result in higher productivity and lower operating costs in general. ICF Kaiser Engineers, of Oakland, California, were awarded the con-tract for detailed design of the process facilities, which was essentially complete by the end of 1993. The project at present is awaiting completion of the environmental permitting process; state air and water permits are in hand, and the Bureau of Land Management's (BLM) current schedule indicates that the final obstacles to construction will be cleared by early fall of this year.

Jan 1, 1994

By G. Van Weert

Oxygen transfer from dispersed air in agitated slurries represents an important unit operation in the minerals processing industry. Gold leaching, iron precipitation and especially bio-oxidation come readily to mind. However, little engineering information is available on the variations between impeller types on such O2 transfer. Engineering literature on the subject, i.e. information which relates slurry density and energy input to O2 transfer, is reviewed and compared to current experimental work. The latter was carried out with minus 50 micron sand/water slurries in a 64 I laboratory tank of standard proportions, equipped with a variable speed drive with torque meter. A standard Rushton turbine and a specifically sized A315 were compared. Results confirm an increasing impairment of O2 transfer with increasing slurry density for both impellers. The volumetric mass transfer coefficient, k,a, in a 10 vol. % slurry shows a decrease of 30% compared to the k,a in water. At 20 vol. % sand this decrease is near 50 %, depending somewhat on superficial gas velocities. Power efficiency, i.e. the kg O2/kWh, decreases about 25 % more rapidly for the Rushton turbine than for the A315 with the addition of sand. However, for equivalent O2 transfer the Rushton turbine was more efficient in this work. Experimental results are presented and their significance for slurry bio-oxidation discussed.

Jan 1, 1996

By Neal Retzer, Adam Bedell, Nick Cioffredi

The first wagon trail across Loveland Pass was built in 1869 thus starting the struggle between the Colorado Rockies and interstate travel. The 1st Pioneer Bore underneath Loveland Pass at the Continental Divide in Colorado was attempted between 1941 and 1943 and was abandoned due to ground conditions at the Loveland Fault. Construction on the nearby Eisenhower Tunnel began in 1967 and was completed in 1973. Numerous challenges associated with tunneling, including at 11,000 ft were overcome. The purpose of this paper is to summarize the history of investigation and construction challenges associated with the Eisenhower Tunnel to celebrate its 50th anniversary.

Jun 13, 2023

By Adolph V. Mitterer

International Minerals and Chemical Corporation operates one of six potash mines in the Carlsbad potash basin. More than 90 percent of America's potash is produced at Carlsbad and IMC accounts for about one-fifth of that amount, Since the Company began operations in 1941 it has mined nearly 50 million tons of ore. Of the two types of ore mined at Carlsbad the principal tonnage is sylvinite in which sylvite-potassium chloride-is the ore mineral. It is produced by IMC as well as by all other mines in the area, In addition to sylvinite IMC is the exclusive producer of langbeinite ore--potassium-magnesium sulfate. From its two ores, International produces a spectrum of 8 high-quality agricultural and industrial chemical products.

Jan 1, 1959

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a significant quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives, the authors have considered original equipment manufacturer (OEM) haul trucks, which are commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application and efficiently manage energy consumption.

Jan 1, 2010

By Lex L. Udy

External detonation generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating ex-plosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall. The effects of this phenomenon on several explosive compositions and types are demonstrated and discussed. Explosives tested include aluminum sensitized and explosive sensitized slurries, ANFO, liquid explosives and dynamites. Various techniques are described that can be used to reduce or eliminate the plasma effect.

Jan 1, 1978