Search Documents

By M. Mathiba

High CO2 fluxes associated with reclaimed coal mine spoils pose an environmental hazard where such sites are used for building. CO2 concentrations in excess of 25% have been reported in homes constructed on or down gradient of such spoils. The objective of this study was to investigate the effect of a mitigation trench used at one mine site on CO2 fluxes across the trench using chamber?based trace gas measurement. LI8100 automated CO2 flux system was used to measure CO2 fluxes from 32 sample points located across a deep mitigation trench on June 8 and 9. The maximum recorded fluxes were 7.29 and 8.18 µmol/m2/s, with averages of 4.15 and 5.50 µmol/m2/s, up and down-dip respectively. These preliminary results show CO2 flux is higher up-hill than down-hill at 95% significant level. This work shows that flux measurement can be used to investigate CO2 migration on reclaimed mine land. Further work is necessary to allow geostatistical modeling of the spatial variability of CO2 fluxes over reclaimed coal mine spoils. Knowledge gained would assist mining practitioners and regulators in reclamation planning for envisaged post-mining land uses.

Jan 1, 2010

By A. Fleming

The exploration process, like any other commercial activity, can only succeed if the objective of the exercise is clearly defined and persistently pursued. Successful exploration requires properties, funding, personnel and persistence. Many of us have years of experience in conducting exploration in our countries of residence. Conducting exploration in a foreign country, however, requires a number of significant other criteria.

Jan 1, 1997

By F. D. Wicks

This paper summarizes the direct operating cash costs for the Barrick Mercur open pit gold mine. A comprehensive, detailed system of cost management has been in effect for the life of the Mercur operation. This system provides the basic data for operations control and is the basis for drafting budgets as well as analyzing impact of change on operations costs. The ore body is complex geologically and metallurgically, requiring operators to pay close attention to mining and processing costs. The cost history provides data which enables analysis of changes in production levels, aging of the mine production fleet, and the impact of specific cost changes through time.

Jan 1, 1993

By Jim Buckley, Ryan Sibley, Scott G. Giltner, Thomas Pallua, Joe Schrank, Robert Cidlik

Because of variation in rock type and site conditions, it is important to create site-specific prediction models for peak particle velocity (PPV) and understand instrumentation mounting locations to better interpret the readings provided following blasting operations. The Atlanta Airport is expanding the section of underground tunnels for its Plane Train people mover, and drill and blast operations were determined to be the suitable method of excavation for the project. Extensive work was done to begin creating prediction models and determining levels of concern based on readings from various types of instrumentation. This paper analyzes the effect of close quarters construction blast vibrations and observed frequency spectrum on existing structures with data from 22 different seismographs mounted in various locations and ground conditions.

Dec 1, 2022

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

By Richard E. Thill

Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind-backfilling process has been particularly successful for stabilizing ground over abandoned and inaccessible underground coal mines. Using this newer technology, vast quantities of backfill material can be distributed over wide areas in underground openings from a small number of injection boreholes. The rapid and successful development of this backfilling method, however, has outstripped technology for monitoring and controlling backfill placement. Surface or borehole remote sensing methods are needed to determine where fill material is being distributed underground and how effectively the material is packed in the voids. In search for improvements in backfill monitoring and control technology, potential remote geophysical sensing, process monitoring, and tracer methods were evaluated to select candidate systems for monitoring backfill placement under the constraints imposed by the injection process and the surface and subsurface conditions. ' A multiple objective ranking matrix, based on theoretical considerations as well as pragmatic experience with systems working in related or similar conditions, was used to narrow down potential methods to several most-favored candidates. Two of the candidates were field tested under actual operating conditions at a backfilling site in the Wilkes-Barre-Scranton region of northeastern Pennsylvania. Although process and acoustic emission monitoring indicated promise for improving existing backfill monitoring technology, more extensive testing under different conditions at various sites is required to establish the validity and utility of these methods. Results indicate that no single method is adequate in itself for backfill monitoring, and that a successful system will require the Integration of several methodologies.

Jan 1, 1982

By Gerald L. Colborne

The major role of financial institutions in the free world in the development of mineral resources is to provide the necessary capital in the form of loans to underwrite the development of these resources by the industry on a stable and continuous basis. This capital provided by the depositors to the bank must be invested in sound projects where the degree of risk is relatively small, the return on the investment is reasonable and the time to retire the loan is of short duration. Money is, therefore, one of the important ingredients along with technology, manpower and an exploitable resource that will provide a sound economic base in this region of development. Canadian banks are similar to banks of other western nations, although each country has some differences in their banking systems. The basic difference between the American and Canadian systems is that the former employs unit banking while the Canadian utilizes the more mobile branch system, which is prohibited or restricted in the United States and some other countries. Canadian banks are the subject of this paper, so, subsequent material will relate to Canadian banks unless indicated otherwise. It will be realized by everyone that the mineral industry is only one area of the economy in which the banks are interested and to cover the subject matter in the time allowed, the topic is restricted to mineral resource development. In Canada this is a vital sector of our economy and before we outline some of the details of financing and services involved in various aspects of mineral development, a review of the Canadian mineral industry is a necessary part of the sequence of presentation. The writer presents this material as a resource engineer advising a major bank in mineral matters, so the presentation may relate more to the financial problems of the developer

Jan 1, 1972

By Gary W. Hudiburgh

The gangue in some magnetite ore bodies contains feldspar; the alkali content of the feldspar reduces the usefulness of these iron ores. One method of decreasing the feldspar content in magnetite concentrate is froth flotation. The amine flotation of feldspar from magnetite concentrate was investigated using zeta potential measurements, Hallimond tube flotation tests and laboratory-scale flotation tests. The zeta potential of various feldspars (microcline, albite, anorthite, oliqoclase and anorthoclase) were determined as a function of pH; the point of zero charge ranged from pH 1.4 to 2.5. Hallimond tube flotation tests using two amine reagents were conducted on the feldspars. Hallimond tube flotation tests using six amine flotation reagents were performed on the cobber tails (quartz, albite and microcline) from a magnetite concentrating plant; in all cases, over 85 percent flotation recovery was obtained at pH 8 and 10-5 to 10-4 [M] collector addition. Laboratory-scale (667 grams) flotation tests were performed on the magnetite concentrate in an attempt to float the feldspar which had reported to the concentrate. The effects of three different collectors, two levels of collector concentration, three pH levels, starch and HF acid were investigated.

Jan 1, 1975

By Jodi Banta

Thanks to strong industry support and longstanding partnerships, the University of Arizona has provided extensive pre-college mining education and outreach for more than a decade. These efforts to promote mining-related degree programs and the wide variety of indemand career opportunities reach thousands of middle and high school students and hundreds of teachers every year. The School of Mining Engineering & Mineral Resources is constantly looking at ways to help students overcome barriers into degree programs. But competition among degree programs for talent is fierce, and outreach has not made a big enough difference in the number of students pursuing mining engineering degrees. With workforce shortages threatening to undermine the industry, more is needed. The Bureau of Labor Statistics estimates 500 new mining engineering jobs each year, and according to a study by Deloitte (2023) nearly 50 percent of skilled engineers will reach retirement age in the next decade. At the same time, the 14 accredited mining or mineral engineering degree programs in the United States are producing fewer than 200 graduates annually (Society of Mining Professors and Society for Mining, Metallurgy & Exploration, 2021). To better understand mining’s competitive position, the School of Mining Engineering & Mineral Resources conducted a comprehensive study to determine (1) how prospective college students, parents and educators perceive the industry, related careers and the mining engineering degree, (2) factors affecting students’ choices of degrees and career plans and (3) the roles parents and educators play and how they influence students. This article is the first of two installments to discuss the results. This installment focuses on what students, parents and educators think about mining and where they get those impressions, as well as the role parents and educators play in influencing students’ choices of careers and degrees. The second installment, scheduled for publication in a later issue of Mining Engineering, looks at what students are seeking in their degrees and careers, and how mining compares with other degrees and industries.

Sep 1, 2025

By R. E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on giving mine operators the capability to evaluate the higher production, the lower costs, and safety enhancement that comes with mechanical mining. The opportunities for low cost and high production must outset the high capital costs associated with mechanical excavation. Giving the mining industry the tools to effectively evaluate and successfully implement mechanical methods defines the challenges and directions of the mechanical mining industry.

Jan 1, 1994

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive, and it is quantified as a confined or unconfined velocity. The confined velocity is more significant as explosives are usually used under a definite degree of confinement. This study evaluates the stepwise increment of the air-deck volume from 10 to 30 percent, and its effect on the VOD. The VOD estimation in the 172-mm-diameter explosive column was conducted using the Dáutriche technique. The air-deck volume increment has an attenuation effect on the steady-state VOD, and detonation failure is high at 30 percent air-deck volume. This attenuation effect is directly linked to the explosive’s rating and efficacy. The air-decking approach in this study is different from conventional air-decking techniques in that it does not employ the fixed blasthole parameters, air-deck volume and specific VOD. 

By T. Harris

Exports of crude gypsum from Mexico currently comprise about 60% of all domestic shipments, and about 25% of the imported material consumed in the U.S. wallboard industry. However, of growing importance are the domestic markets for calcined gypsum in Mexico including building plasters and wallboard, which account for 55% of the internal demand for natural mined material. This paper will examine the current trends in the production and trade of natural mined gypsum in Mexico and North America and the opportunities and threats that are facing existing and new suppliers in this changing market.

Jan 1, 1996

By I. A. Tinto

Labrador City is located in the southwestern portion of Newfoundland-Labrador, approximately 965 kilometers north-east of Montreal. The mine and beneficiation complex of the Iron Ore Company of Canada, known as the Carol Project, is situated 535 metres above sea level in a climatic region characterized by cold winters and short, cool summers. History The iron Ore Company of Canada commenced work in the area in 1949, however, it was not until 1958 that the decision was made to proceed with mining operations. The ore body consists of Specular Hematite (Fe203) and Magnetite (Fe304) with small quantities of Limonite and Geothite. The average grade of the ore bodies is 39% iron.

Jan 1, 1985

By Francis X. McCullough

After OSHA published a Notice of Proposed Rulemaking on August 5, 1983, to revise its standards for Underground Construction, many contractors and their representative associations became concerned by the sweeping changes in the proposed rule. After reviewing all of the evidence and testimony on file with OSHA, the contractors presented extensive written and oral testimony to the Department of Labor in Washington, D. C. to help insure that the final published rule would be effective without jeopardizing the economic viability of the industry. The results of those efforts, the entire OSHA rulemaking process, and the opportunity for the construction industry to participate in that process will be discussed.

Jan 1, 1985

By E. W. Davis

This paper deals with the role of the Maintenance Department in a milling operation; specifically, the Mines Development, Inc., processing plant at Edgement, South Dakota. The goal of very maintenance department is the smooth and uninterrupted operation of the plant it serves, To achieve this goal, maintenance men adapt various features and procedures into a program designed to fit the characteristics of their particular plant operation. A few of the basic elements of a sound maintenance program are: 1, A periodic preventive maintenance schedule. 2, A systematic inspection and lubrication procedure. 3. A training program for maintenance personnel. 4 A good equipment-history file system, 5. A carefully planned spare parts inventory.

Jan 1, 1962

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of 4 foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with MSHA’s lower coal mine respirable dust standard (1.5 mg/m3). Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used a low pressure air generated by a blower and water pressure using a NIOSH developed foam generator. Foam property tests comprising of a bottle shake test, foam expansion ratio, and water drainage were used to classify foams. The bottle shake tests determined that the lowest concentration of foam agent to be used was approximately 1.5%. Compressed air generated foams tended to have low expansion ratios (10-19) with high water drainage. Blower air generated foams had higher foam expansion ratios (30-60) with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The different foam agents produce foams with different material properties. Results of testing eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents, while having different foam properties, seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. INTRODUCTION About one-half of U.S. underground coal is produced by longwall mining. This technique allows for mining high volumes of coal, producing significant amounts of coal mine dust. This can lead to the overexposures to longwall miners and possibly occupational respiratory diseases black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [1]. When respirable quartz is present, the mine must maintain an average concentration at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present [2]. Respirable dust samples collected by U.S. Mine Safety and Health Administration inspectors for the five-year period from 2010 to 2014 found that 5.6% (53 of 943 respirable coal mine dust samples) of the longwall operators on the tailgate side exceeded the coal mine dust standard, and 4.3% (76 of 1768 samples) of the jacksetters exceeded the standard. If silica is present, the reduced standard is implemented, meaning that 11.4% (36 of 316 respirable coal mine samples analyzed for dust) of the jacksetters exceeded the reduced standard. Only 3.8% (18 of 478 samples) of the longwall operators on the tailgate side exceeded the reduced standard [3]. Had the 1.5 mg/m3 standard been in effect during this period, non-compliant samples would have been much higher. For example, over 15% of the samples collected at the tailgate shearer operator occupation exceeded the lower standard."

Jan 1, 2017

By V. Z. Sun

One of the major concerns of ground control in a coal mine is safety against failure of one of three components (i.e. roof, pillar, or floor) of the mine entry. In order to better design and evaluate stability of the mine entry with a certain confidence, a reliability approach is introduced rather than using the conventional safety factor (SF) method only. Advantages of using the reliability approach is that it not only takes variability of both rock/coal properties and stress distribution into consideration, but also assesses the stability of each component and mine entry as a whole system. Therefore, it is anticipated that, by using this approach, the current ground control technology in coal mine will convey a better sense of confidence. The results of a case example show a significant influence on the current design concept and stability evaluation of mine entry.

Jan 1, 1997

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V, 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

May 4, 2023

By M. D. Bath

Minproc Engineers Inc. (Minproc) recently completed the construction and start-up of a process facility to treat 14,000 t/d of gold-silver ore at Kori Kollo, Bolivia. The comminution circuit consists of crushing and SAG-ball mill grinding. Breakage characteristics of the ore were determined and a circuit model developed. This enabled variations of the circuit to be simulated, and evaluated in terms of predicted performance to provide the criteria for final engineering design. Subsequently, analysis of the operating circuit provided data for circuit model-fitting. The validity of the original model and circuit performance predictions are discussed.

Jan 1, 1994

By David Maust, Rob Albinger, Mike Walling, Michael Rispin

The safeguarding of health and life is the number one priority for underground infrastructure projects. While culture and approach are critically important, the industry has also seen the development of innovative tools and technologies that assist in making the underground environment and working places more safe and secure, both on an everyday basis and in the event of an unexpected occurrence.

Dec 1, 2022